基于U形塑料光纤的氧气传感器

报道了一种基于荧光猝灭原理的光纤氧气传感器.采用塑料光纤作为传感和传光元件进行氧气传感,传感头制成U形.以邻菲咯啉钌作为荧光标记物,用溶胶-凝胶法制备敏感材料.采用相移法来实现对荧光寿命的测定.测量了不同弯曲半径传感头对氧气传感的灵敏度,发现当U形光纤的弯曲半径较小时系统的灵敏度较高.对荧光寿命和氧气浓度的关系进行了测量,发现二者呈亚线性关系,提出双荧光体模型解释这一实验现象.

低损耗有机无机混合溶胶凝胶波导的实验研究

利用有机无机混合的溶胶凝胶方法在硅基底上制备波导薄膜．采用正硅酸四乙酯和苯基三乙氧基硅烷作为反应先驱物，利用旋涂的方法成膜，对其折射率，传输损耗以及条形波导的光刻、刻蚀特性进行了研究．测量了波导薄膜折射率随成分变化的关系．实验表明，该方法工艺简单，可以获得具有较低损耗的波导薄膜．测试得到632．8nm波段的损耗系数为0．23dB／cm．采用ICP刻蚀工艺获得了较为平整的条形波导．

利用有机-无机溶胶-凝胶方法制备平面波导环形谐振腔

采用简单的有机一无机混合的溶胶一凝胶方法制备了折射率在一定范围内可调的波导材料，并利用其制备了平面波导环形谐振腔器件。波导结构呈现倒脊形，其制备工艺首先是利用感应耦合等离子体刻蚀技术（ICP）在二氧化硅衬底上刻蚀波导结构的凹槽，然后再沉积波导薄膜。利用光谱仪对器件的传输特性进行了测量，观测到具有10dB对比度，自由光谱范围0．182nm周期性谐振现象，结合环形谐振腔的传输特性，得到环形腔具有较低的传输损耗1．7dB／cm。同时对环形谐振腔的温度特性进行了测量，得出波导材料的热光系数为-1．54×10^-4

钛宝石强激光负载的有机硅复合凝胶增透膜研究

以硅酸四乙酯(TEOS)和甲基三乙氧基硅烷(MTEOS)为前驱材料，用溶胶-凝胶(sol-gel)方法在钛宝石表面制备得到均匀性良好且具有高激光损伤阈值的有机硅复合凝胶增透膜。膜层在钛宝石激光器输出波段(750～850nm)的增透效果显著，其平均透过率超过98．6％；激光破坏阈值为2．2J／cm^2(800nm，300ps)；膜层表面均匀性达到激光波面的要求，在皮秒、飞秒超短脉冲高功率激光领域具有应用价值。溶胶的性能测试结果表明，溶胶粘度和成膜折射率均随溶液中CH3SiO1.5溶胶体含量的增加而增大，而膜

Modified porous silica antireflective coatings with laser damage resistance for Ti:sapphire

Porous SiO2 antireflective (AR) coatings are prepared from the colloidal silica solution modified with methyltriethoxysilane (MTES) based on the sol-gel route. The viscosity of modified silica suspensions changes but their stability keeps when MTES is introduced. The refractive indices of modified coatings vary little after bake treatment from 100 to 150 Celsius. The modified silica coatings on Ti:sapphire crystal, owning good homogeneity, display prominent antireflective effect within the laser output waveband (750-850 nm) of Ti:sapphire lasers, with average transmission above 98.6%, and own laser induced damage thresholds (LIDTs) of more than 2.2 J/cm2 at 800 nm with the pulse duration of 300 ps.

溶胶-凝胶多孔二氧化硅减反膜稳定性研究

多孔SiO2膜层经热处理后，具有很高的激光破坏阈值，但是结构中有许多Si-OH亲水基团，导致光学透过率受环境相对湿度的影响很大。实验目的是改善膜层内部结构，使膜层结构中的亲水基团转变为疏水基团。提高膜层的疏水性，增强膜层的透过率稳定性。系统地研究了膜层透过率随时间变化的规律，在氨气和六甲基二硅氮烷(HMDS)混合气氛下热处理膜层，处理后生成Si-O-Si(CH2)3非极性疏水基团，使膜层的疏水性大大提高，因而膜层的透过率稳定性有大幅度提高。稳定性的提高延长了膜层的寿命。处理后膜层的表面粗糙度良好，均方根表

掺入有机硅提高溶胶-凝胶二氧化硅减反膜的稳定性研究

膜层稳定性对于激光器能否长期稳定使用极为重要。多孔SiO。减反膜经热处理后，结构中还存在许多Si—OH亲水基团，透过率稳定性受环境相对湿度的影响较大。向膜层中掺入有机硅，添加疏水基团，提高了膜层的疏水性，增强了膜层的透过率稳定性。膜层中加了Si-CH3疏水基团，膜层的疏水性大大提高；当Si-CH3与二氧化硅悬胶体中的Si的摩尔比为1／5．7时，即Si—CH3质量分数为0．35％时的二氧化硅膜层，其减反效果好，疏水性也高，从而大幅度提高了膜层的透过率稳定性，延长了膜层的寿命，对二氧化硅膜层具有高激光损伤阈值

磷酸盐激光玻璃聚（CH3）2Si（OC2H5）2防潮膜

以（CH3）2Si（OC2H5）2为前驱体，采用溶胶-凝胶与有机合成相结合的方法，制得稳定性良好的涂膜液。采用旋转涂膜法在掺钕磷酸盐激光玻璃棒端面涂制防潮膜，膜层固化后透过率达96．5％，获得的膜层表面粗糙度优良，均方根表面粗糙度（RMS）为1．659nm，平均粗糙度（RA）平均为1．321nm；在激光波长1053nm，脉冲宽度1 ns条件下膜层的激光破坏闽值可达10～14 J／cm^2。经过“神光Ⅱ”高功率激光器物理实验运行，膜层使用期为五年，并且已经在我国“神光Ⅲ”原型装置上试用。

磷酸盐激光玻璃凝胶防潮膜和减反膜

采用溶胶-凝胶方法制备（CH3）2Si（OC2H5）2预聚体涂膜液以及掺入SiO2悬胶体涂膜液改性，采用旋转法在掺钕磷酸盐激光玻璃棒端面涂制防潮膜，热处理后膜层固化。SiO2改性的CH3O防潮膜，热处理后的膜层耐摩擦性能明显改善。然后旋转涂制第二层多空性SiO2减反膜，涂膜胶体通过硅酸乙脂碱催化水解缩聚制得，减反膜的折射率为约1．25，玻璃棒涂膜后激光波长1053nm减少表面反射率6．5％-7．5％，双层膜激光破坏阈值12J／cm^2，1053nm／1ns，膜层表面粗糙度（RMS）2．523nm。直径20

高激光损伤阈值溶胶-凝胶ZrO2薄膜

采用醇热法水解氧氯化锆（ZrOCl2·8H2O）制备ZrO2溶胶，提拉法涂膜。采用粘度、粒度分布、折射率、IR、DSC、AFM等测试手段对溶胶和薄膜性能进行表征。结果表明，ZrO2溶胶颗粒的平均粒径为18．9nm，薄膜经300℃热处理后折射率可高达1．95，膜层表面均匀平整，表面平均粗糙度仅为0．561nm，膜层的激光损伤阈值为14J／cm^2（1064nm，1ns）。

Optical properties of dye-doped zirconia films by spectroscopic ellipsometry

The optical properties of zirconia films doped with rhodamine 6G and oxazine 725 by the sol-gel process were investigated using spectroscopic ellipsometry (SE). Accurate refractive index n and the extinction coefficient k were determined using a three-oscillator classical Lorentz model in the wavelength range of 300-800 nm. The derived refractive index of dye-doped films exhibited anomalous dispersion in the absorption region. Wavelength tunable output lasing action yellow and near-infrared wavelength region was achieved by DFB configuration using zirconia films doped with R6G and oxazine 725. (c) 2006 Elsevier B.V. All rights reserved.

Optical properties of zirconia-titania-ORMOSIL films for temperature tuning distributed feedback waveguide lasers

The zirconia-titania-ORMOSIL waveguide thin films with considerable optical quality were prepared by the sol-gel process. The refractive index (n) and the extinction coefficient (k) were determined by a scanning ellipsometer. Wavelength tunable output of distributed feedback waveguide lasing was demonstrated in Rhodamine 6G doped ZrO2 TiO2-ORMOSIL thin films by varying the temperature, and about 5.5 nm wavelength tuning range was achieved around the emission wavelength of 599 nm. The thermal-optic coefficient (dn/dT) of the active ZrO2-TiO2-ORMOSIL films was deduced. (c) 2005 Elsevier B.V. All rights reserved.

Effect of processing parameters on the optical properties of TiO2/ormosil planar waveguide

Hybrid TiO2/ormosil waveguiding films have been prepared by the sol-gel method at low thermal treatment temperature of 150° C. The influence of processing parameters including the molar ratios of titanium butoxide (Ti(OBu)(4))/3-glycidoxypropyltrimethoxysilane (GLYMO) and H2O/Ti(OBu)(4) (expressed as R), especially aging of sot on the optical properties was investigated. The optical properties of films were measured with scanning electron microscope (SEM), UV/VIS/NIR spectrophotometer (UV-Vis), m-line and the scattering-detection method. The results indicate that the film thickness increases with the increase of sol aging time, but the variation of refractive index as a function of sot aging time depends on the relative ratios of GLYMO to Ti(OBu)(4). Higher transmittance and lower attenuation of the planar waveguide can be obtained in the sol with lower Ti(OBu)(4) contents and shorter aging time.

Study of hybrid TiO2/ormosil films doped with laser dyes

TiO2/ormosil films doped with laser dyes have been prepared by the sol-gel method. Spectroscopic properties of the entrapped dyes are studied by the absorption and emission techniques. The results indicate that the absorption and fluorescence spectra of kiton red depend strongly on the properties of the ormosil matrices. The heat-treatment of the kiton red-doped film obviously leads to the increasing fluorescence intensity and the largest fluorescence intensity is obtained after heat-treatment of 150 degrees C for 2 h. However, the fluorescence intensity of the rhodamine 6G-doped film decreases with the increase of the heat-treatment temperature. (c) 2005 Elsevier B.V. All rights reserved.

Preparation and characterization of hybrid ZnO/ormosils films

Hybrid ZnO/ormosils Elms are prepared by the sol-gel method. A FT-IR spectrometer, 900 UV/VIS/NIR spectrophotometer, atomic force microscope, and ellipsometer are employed to investigate microstructure and optical properties of the films fired at different temperatures. The results show that the films with high transmittance and low surface roughness could be obtained at the heat-treatment temperature of 150 degrees C, the refractive index and thickness of the film are 1.413, 2.11 mu m, respectively. Higher temperatures (350 degrees C, 550 degrees C) change the Elm microstructure severely, and then decrease the transmittance of the films.