Hybrid Scaffolds Built From PET and Collagen as a Model For Vascular Graft Architecture

A hybrid material with excellent mechanical and biological properties is produced by electrospinning a co-solution of PET and collagen. The fibers are mapped using SEM, confocal Raman microscopy and collagenase digestion assays. Fibers of different compositions and morphologies are intermingled within the same membrane, resulting in a heterogeneous scaffold. The collagen distribution and exposure are found to depend on the PET/collagen ratio. The materials are chemically and mechanically characterized and biologically tested with fibroblasts (3T3-L1) and a HUVEC culture in vitro. All of the hybrid scaffolds show better cell attachment and proliferation than PET. These materials are potential candidates to be used as vascular grafts.

Hybrid Materials Based on Smectite Clays and Nutraceutical Anthocyanins from the Acai Fruit

Hybrid materials were prepared by combining clay mineral (montmorillonite SWy-2 and saponite SapCa-1) and dyes extracted from the acai (Euterpe oleracea Mart.) fruit, which contains mainly anthocyanins from the 3-glucoside class, to increase the stability of the dye and facilitate its handling and storage. Clay minerals are common ingredients in therapeutic and pharmaceutical products and acai phytochemicals show disease prevention properties. The extract of the acai fruit was mixed with water suspensions of layered silicates in different proportions. The dyeclay hybrids presented incorporated organic material in amounts up to 24 wt.-%. X ray diffractometry and vibrational (FTIR and Raman) and electronic spectroscopic data showed that flavylium cations were successfully intercalated between the inorganic layers. Mass-coupled thermogravimetric analysis (TGA-MS) data showed a significant gain in the thermostability of the organic species in relation to anthocyanins in the extract. MS curves related to CO2 release (m/z = 44) are ascendant above 200 degrees C when the dye cations are confined to the inorganic structure. The radical scavenging activity of the hybrid materials was monitored by electron paramagnetic resonance (EPR) toward the stable radical DPPH (1,1-diphenyl-2-picrylhydrazyl) and compared to the activity of the acai extract. In addition to the fact that interaction with clay minerals improves the stability of the acai dyes against heat, their properties as radical scavengers are preserved after intercalation. The improvement in the properties of the nutraceutical species by intercalation by using biocompatible inorganic structures can be valuable for human therapy.

Selection and Use Recommendation in Hybrids of Ornamental Banana

The ornamental market is dynamic and demands constant novelties. The use of fruit crops as ornamental plants can be an interesting alternative with very differentiated and original products. The banana germplasm bank at Embrapa Cassava and Fruits has been primarily used in the breeding program for generating new cultivars as food. To diversify and expand the use of this collection, accessions with ornamental potential have been selected to obtain new hybrids. This work was aimed at characterizing the progeny of ornamental Musa L. spp. by grouping the hybrids according to the following uses: landscape plants, potted plants, cut flower, or minifruits. Forty-two hybrids were evaluated with 14 quantitative and 12 qualitative descriptors in three production cycles. In addition, assays for resistance to black and yellow Sigatoka and to Fusarium wilt were performed. Variability was observed for all the characteristics evaluated within progenies, especially with regard to leaf color, fruit, peduncle, rachis, and heart. All evaluated hybrids were resistant to yellow Sigatoka and to Fusarium wilt and were resistant or showed reduced symptoms of susceptibility to black Sigatoka. Most hybrids (82%) presented reduced plant height. After clustering by use category, the hybrids RM 09, RM 38, RM 37, and RM 33 were selected and recommended to be used as cut flowers, minifruits, or landscaping plants.

GENERALIZED FINITE ELEMENT METHOD ON NONCONVENTIONAL HYBRID-MIXED FORMULATION

The generalized finite element method (GFEM) is applied to a nonconventional hybrid-mixed stress formulation (HMSF) for plane analysis. In the HMSF, three approximation fields are involved: stresses and displacements in the domain and displacement fields on the static boundary. The GFEM-HMSF shape functions are then generated by the product of a partition of unity associated to each field and the polynomials enrichment functions. In principle, the enrichment can be conducted independently over each of the HMSF approximation fields. However, stability and convergence features of the resulting numerical method can be affected mainly by spurious modes generated when enrichment is arbitrarily applied to the displacement fields. With the aim to efficiently explore the enrichment possibilities, an extension to GFEM-HMSF of the conventional Zienkiewicz-Patch-Test is proposed as a necessary condition to ensure numerical stability. Finally, once the extended Patch-Test is satisfied, some numerical analyses focusing on the selective enrichment over distorted meshes formed by bilinear quadrilateral finite elements are presented, thus showing the performance of the GFEM-HMSF combination.

Self-supported bacterial cellulose/boehmite organic-inorganic hybrid films

Self-supported organic-inorganic hybrid transparent films have been prepared from bacterial cellulose and boehmite. SEM results indicate that the BC membranes are covered by Boehmite and XRD patterns suggest structural changes on cellulose due to Boehmite addition. Thermal stability is accessed through TG curves and is dependent on Boehmite content. Transparency, as evaluated by UV-Vis absorption, increases with increasing content of boehmite suggesting application of these materials as transparent substrates for opto-electronic devices.

Glass/PDMS hybrid microfluidic device integrating vertically aligned SWCNTs to ultrasensitive electrochemical determinations

This communication reports a promising platform for rapid, simple, direct, and ultrasensitive determination of serotonin. The method is related to integration of vertically aligned single-walled carbon nanotubes (SWCNTs) in electrochemical microfluidic devices. The required microfabrication protocol is simple and fast. In addition, the nanomaterial influenced remarkably the obtained limit-of-detection (LOD) values. Our system achieved a LOD of 0.2 nmol L-1 for serotonin, to the best of our knowledge one of the lowest values reported in the literature.

Fatty acids as a tool to compare cachara (Pseudoplatystoma reticulatum) (Siluriformes: Pimelodidae) and hybrid (Pseudoplatystoma corruscans x Pseudoplatystoma reticulatum) larvae during early development

In this study, we investigated the physiological alterations during ontogeny for cachara (Pseudoplatystoma reticulatum) and their hybrid larvae (Pseudoplatystoma corruscans x P. reticulatum) using lipids and fatty acids as physiological tools to elucidate the basis for differences in these groups' productivity in an industrial setting. Eggs and larvae samples were collected during January and February of 2008 in the city of Bandeirantes, MS, and were divided into three primary phases: phase I (0-16 h after fertilization); phase II (24 h after fertilization to 6 days after fertilization); and phase III (7-25 days after fertilization). The larvae of both groups showed a high degree of similarity, suggesting that the hybrid larvae showed a high level of heritability from the cachara broodstock. Analysis of the total lipid content provided evidence that there is no alteration in lipid concentration during ontogeny for both groups (i.e., the cachara and hybrids). However, the fatty acid profile showed that during the endogenous feeding period (phase II), when the larvae must use the energy reserves from the mother, the cachara larvae used mainly monounsaturated fatty acids for development. This is typical for most fish species, though notably, the hybrids preferentially used saturated fatty acids. Furthermore, certain specific changes demonstrate unique patterns of energy utilization and structural substrates, which may aid in elucidating the empirical differences reported by fish farmers (i.e., that the hybrids perform better than cacharas in captivity).

The fatty acid profiles and energetic substrates of two Nile tilapia (Oreochromis niloticus, Linnaeus) strains, Red-Stirling and Chitralada, and their hybrid

Protein and lipid content as well as the fatty acid (FA) composition of storage tissues were analysed in two varieties of Oreochromis niloticus (Red-Stirling and Chitralada) and their hybrid. The animals were maintained in cages for 11 months. The samples were taken when the animals weighed 10, 50, 100, 250 and 500 g. The results showed that changes in the metabolic processes occur during an increase in body mass in both varieties of tilapia and also their hybrid, but that these differences are not found in animals collected at the commercial weight. The protein content of the fillet and liver decreased with growth and the same protein content associated with growth was found for fillet lipid content. The genetic variety did not influence the FA profile of the fillet, but different genotypes had different hepatic FA compositions. Even with the same lipid content, the hepatocytes of Chitralada accumulated higher levels of polyunsaturated fatty acids (PUFA) n6 in triglycerides and increased C22:6n3 in the hepatocyte membranes. The higher n6PUFA content was compensated by a lower fraction of saturated FA in the hepatocyte triglycerides. The skin of Chitralada also had higher n6PUFA and C22:6n3 contents, suggesting a higher ability to deposit PUFA in the skin due to alterations in the liver synthetic pathway.

Spectroscopic, morphological and electrochromic characterization of layer-by-layer hybrid films of polyaniline and hexaniobate nanoscrolls

The combination of semiconducting oxides and polyaniline in the nanoscale range may result in hybrid materials having enhanced properties, such as electrochromism and charge capacity. This paper reports the spectroscopic, morphological and electrochromic characterization of hybrid films made up of hexaniobate one-dimensional (1D) nanoscrolls and polyaniline prepared by the layer-by-layer assembly technique (LbL). Secondary electron imaging and backscattered electron imaging techniques performed using a scanning electron microscope showed that polyaniline is adsorbed on the hexaniobate nanoscrolls, which confirms the combination of the components in the nanoscale domain. UV-VIS-NIR electronic spectra of the LbL hybrid films showed the absorption tail in the NIR region, assigned to delocalized polarons of the polyaniline. Resonance Raman spectra in the 1000-1700 cm(-1) range indicated that hybrid films present a higher relative intensity of polaron bands at 1337 and 1508 cm(-1) than pristine polyaniline in the emeraldine salt form. These results suggest that hexaniobate nanoscrolls induce a secondary doping of polyaniline. The cyclic voltammetry (CV) data for the hybrid film showed a specific capacity of 870 C cm(-3). According to CV results, the synergistic effect on charge storage properties of the hybrid material is attributed to the enhanced electroactivity of the hexaniobate component in the LbL film. Spectroelectrochemical experiments showed that the electrochromic efficiencies at 420 nm are ca. -41 and 24 cm(2) C-1 as the potential changes from 0.8 to -0.9 V and from -0.9 to -1.8 V, respectively, whereas at 800 nm the efficiencies are ca. -55 and 8 cm(2) C-1 for the same potential ranges. The electrochromic efficiencies and multi-colour character of the LbL film of hexaniobate nanoscrolls and polyaniline indicate that this novel hybrid material is an interesting modified electrode for electrochromic devices.

Double shunt technique for hybrid palliation of hypoplastic left heart syndrome: a case report

We report a technique to palliate hypoplastic left heart syndrome, with no PDA stenting, but with double polytetrafluoroethylene shunt from pulmonary artery to ascending and descending aorta by combined thoracotomies. A 30-day-old female was operated with this technique. Five months after first operation, the child was submitted to Norwood/Glenn operation. Good hemodinamic recovery and initial clinical evolution was observed. The child was extubated in 8th post operatory day and reentubated in the next day due to pulmonary infection. Despite antibiotic treatment, the child died after systemic infectious complications.

Gibberellic acid in vegetative and reproductive development of Phalaenopsis orchid hybrid genus

The flower industry represents about one billion dollars in Brazil and the development of techniques aimed at flowering control is required. This study evaluated the influence of gibberellic acid (GA3) on the vegetative and reproductive development of young plants of Phalaenopsis FSNT 'Dai-Itigo' hybrid pink color. The application of GA3 was made by foliar sprays at concentrations of 0, 125, 250, 500 and 1,000 mg L -1. The length of leaves increased significantly when using GA3 at low concentrations, but leaf width decreased. The application of GA3 at 125 mg L -1 showed the best results for the promotion of flowering and flower quality of this orchid hybrid. In this treatment, about 50% of plants treated with GA3 flowered about 6-12 months before the plants that were non-treated with this plant growth regulator. The quality of flowering and flowers was best with 125 mg L -1 GA3.

Structural analysis of combinatorial optimization problem characteristics and their resolution using hybrid approaches

Many combinatorial problems coming from the real world may not have a clear and well defined structure, typically being dirtied by side constraints, or being composed of two or more sub-problems, usually not disjoint. Such problems are not suitable to be solved with pure approaches based on a single programming paradigm, because a paradigm that can effectively face a problem characteristic may behave inefficiently when facing other characteristics. In these cases, modelling the problem using different programming techniques, trying to ”take the best” from each technique, can produce solvers that largely dominate pure approaches. We demonstrate the effectiveness of hybridization and we discuss about different hybridization techniques by analyzing two classes of problems with particular structures, exploiting Constraint Programming and Integer Linear Programming solving tools and Algorithm Portfolios and Logic Based Benders Decomposition as integration and hybridization frameworks.

Mixed-domain simulation and hybrid wafer-level packaging of RF-MEMS devices for wireless applications

In questa tesi verranno trattati sia il problema della creazione di un ambiente di simulazione a domini fisici misti per dispositivi RF-MEMS, che la definizione di un processo di fabbricazione ad-hoc per il packaging e l’integrazione degli stessi. Riguardo al primo argomento, sarà mostrato nel dettaglio lo sviluppo di una libreria di modelli MEMS all’interno dell’ambiente di simulazione per circuiti integrati Cadence c . L’approccio scelto per la definizione del comportamento elettromeccanico dei MEMS è basato sul concetto di modellazione compatta (compact modeling). Questo significa che il comportamento fisico di ogni componente elementare della libreria è descritto per mezzo di un insieme limitato di punti (nodi) di interconnessione verso il mondo esterno. La libreria comprende componenti elementari, come travi flessibili, piatti rigidi sospesi e punti di ancoraggio, la cui opportuna interconnessione porta alla realizzazione di interi dispositivi (come interruttori e capacità variabili) da simulare in Cadence c . Tutti i modelli MEMS sono implementati per mezzo del linguaggio VerilogA c di tipo HDL (Hardware Description Language) che è supportato dal simulatore circuitale Spectre c . Sia il linguaggio VerilogA c che il simulatore Spectre c sono disponibili in ambiente Cadence c . L’ambiente di simulazione multidominio (ovvero elettromeccanico) così ottenuto permette di interfacciare i dispositivi MEMS con le librerie di componenti CMOS standard e di conseguenza la simulazione di blocchi funzionali misti RF-MEMS/CMOS. Come esempio, un VCO (Voltage Controlled Oscillator) in cui l’LC-tank è realizzato in tecnologia MEMS mentre la parte attiva con transistor MOS di libreria sarà simulato in Spectre c . Inoltre, nelle pagine successive verrà mostrata una soluzione tecnologica per la fabbricazione di un substrato protettivo (package) da applicare a dispositivi RF-MEMS basata su vie di interconnessione elettrica attraverso un wafer di Silicio. La soluzione di packaging prescelta rende possibili alcune tecniche per l’integrazione ibrida delle parti RF-MEMS e CMOS (hybrid packaging). Verranno inoltre messe in luce questioni riguardanti gli effetti parassiti (accoppiamenti capacitivi ed induttivi) introdotti dal package che influenzano le prestazioni RF dei dispositivi MEMS incapsulati. Nel dettaglio, tutti i gradi di libertà del processo tecnologico per l’ottenimento del package saranno ottimizzati per mezzo di un simulatore elettromagnetico (Ansoft HFSSTM) al fine di ridurre gli effetti parassiti introdotti dal substrato protettivo. Inoltre, risultati sperimentali raccolti da misure di strutture di test incapsulate verranno mostrati per validare, da un lato, il simulatore Ansoft HFSSTM e per dimostrate, dall’altro, la fattibilit`a della soluzione di packaging proposta. Aldilà dell’apparente debole legame tra i due argomenti sopra menzionati è possibile identificare un unico obiettivo. Da un lato questo è da ricercarsi nello sviluppo di un ambiente di simulazione unificato all’interno del quale il comportamento elettromeccanico dei dispositivi RF-MEMS possa essere studiato ed analizzato. All’interno di tale ambiente, l’influenza del package sul comportamento elettromagnetico degli RF-MEMS può essere tenuta in conto per mezzo di modelli a parametri concentrati (lumped elements) estratti da misure sperimentali e simulazioni agli Elementi Finiti (FEM) della parte di package. Infine, la possibilità offerta dall’ambiente Cadence c relativamente alla simulazione di dipositivi RF-MEMS interfacciati alla parte CMOS rende possibile l’analisi di blocchi funzionali ibridi RF-MEMS/CMOS completi.

Caratterizzazione meccanica di calcestruzzi fibrorinforzati con fibre d'acciaio

L’utilizzo di materiali compositi come i calcestruzzi fibrorinforzati sta diventando sempre più frequente e diffuso. Tuttavia la scelta di nuovi materiali richiede una approfondita analisi delle loro caratteristiche e dei loro comportamenti. I vantaggi forniti dall’aggiunta di fibre d’acciaio ad un materiale fragile, quale il calcestruzzo, sono legati al miglioramento della duttilità e all'aumento di assorbimento di energia. L’aggiunta di fibre permette quindi di migliorare il comportamento strutturale del composito, dando vita ad un nuovo materiale capace di lavorare non solo a compressione ma anche in piccola parte a trazione, ma soprattutto caratterizzato da una discreta duttilità ed una buona capacità plastica. Questa tesi ha avuto come fine l’analisi delle caratteristiche di questi compositi cementizi fibrorinforzati. Partendo da prove sperimentali classiche quali prove di trazione e compressione, si è arrivati alla caratterizzazione di questi materiali avvalendosi di una campagna sperimentale basata sull’applicazione della norma UNI 11039/2003. L’obiettivo principale di questo lavoro consiste nell’analizzare e nel confrontare calcestruzzi rinforzati con fibre di due diverse lunghezze e in diversi dosaggi. Studiando questi calcestruzzi si è cercato di comprendere meglio questi materiali e trovare un riscontro pratico ai comportamenti descritti in teorie ormai diffuse e consolidate. La comparazione dei risultati dei test condotti ha permesso di mettere in luce differenze tra i materiali rinforzati con l’aggiunta di fibre corte rispetto a quelli con fibre lunghe, ma ha anche permesso di mostrare e sottolineare le analogie che caratterizzano questi materiali fibrorinforzati. Sono stati affrontati inoltre gli aspetti legati alle fasi della costituzione di questi materiali sia da un punto di vista teorico sia da un punto di vista pratico. Infine è stato sviluppato un modello analitico basato sulla definizione di specifici diagrammi tensione-deformazione; i risultati di questo modello sono quindi stati confrontati con i dati sperimentali ottenuti in laboratorio.