Teaching project: a low-cost swine model for chest tube insertion training

Objective: to describe and evaluate the acceptance of a low-cost chest tube insertion porcine model in a medical education project in the southwest of Paraná, Brazil. Methods: we developed a low-cost and low technology porcine model for teaching chest tube insertion and used it in a teaching project. Medical trainees - students and residents - received theoretical instructions about the procedure and performed thoracic drainage in this porcine model. After performing the procedure, the participants filled a feedback questionnaire about the proposed experimental model. This study presents the model and analyzes the questionnaire responses. Results: seventy-nine medical trainees used and evaluated the model. The anatomical correlation between the porcine model and human anatomy was considered high and averaged 8.1±1.0 among trainees. All study participants approved the low-cost porcine model for chest tube insertion. Conclusion: the presented low-cost porcine model for chest tube insertion training was feasible and had good acceptability among trainees. This model has potential use as a teaching tool in medical education.

One chip solution for low-cost active magnetic bearing system

In this work the implementation of the active magnetic bearing control system in a single FPGA is studied. Requirements for the full magnetic bearing control system are reviewed. Different control methods for active magnetic bearings are described shortly. Flux and the current base controllers are implemented in a FPGA. Suitability of the con-trollers for a low-cost magnetic bearing application is studied. Floating-point arithmetic’s are used in the controllers to ease designing burden and improve calculation precision. Per-formance of the flux controller is verified with simulations.

Cost-effectiveness analysis in South Karelia Central Hospital

The target organization of this study, otherwise South-Karelia Social and Health Care District (Eksote) provides health, senior, family and social welfare services. South Karelia Central Hospital provides special health care and offers health services from all of the most important medical specialties. Eksote has in use 15D instrument to measure the health-related quality of life (HRQoL) of their patients before and after their interventions for observing the health effects of the medical care. Furthermore, 15D allows measuring the effectiveness and cost-effectiveness of health care when comparing these before and after results of the 15D measurements and adding the costs of the interventions into this research. The main purposes of this study were to analyze the effectiveness and cost-effectiveness of medical care in South Karelia Central Hospital by using the gathered 15D data to calculate effectiveness and cost-effectiveness ratios and to analyze the reliability and availability of the data. Study has been conducted using literature review and quantitative research methods. The results indicate that from the patients within the eight units selected to this study the 15D change information was available from the 52 %, the 15D change and the cost information from 38 % and the information of quality-adjusted life years (QALYs) produced and the cost information from 35 %. The effectiveness and cost-effectiveness of medical care were greatest at the units of Pain Outpatient Clinic and Rheumatic Diseases Outpatient Clinic. The most effective medical care is given in the unit where the average price of one produced QALY is the highest (Orthopedics). However, the calculated standard deviations pointed out that there are great variances in the effectiveness and cost-effectiveness within the units also.

A quality and cost approach for welding process selection

The aim of this work was to propose, apply and evaluate a methodical approach to select welding processes in a productive environment based on market requirements of Quality and Costs. A case study was used. The welds were carried out in laboratory, simulating the joint conditions of a manufacturer and using several welding processes: SMAW, GTAW, pulsed GTAW, GMAW with CO2 and Ar based shielding gases and pulsed GMAW. For Quality analysis geometrical aspects of the beads were considered and for Cost analysis, welding parameters and consumable prices. Quantitative indices were proposed and evaluated. After that, evaluation of both Quality and Costs was done, showing to be possible to select the most suitable welding process to a specific application, taking into account the market conditions of a company.

Overview on the Cost-effectiveness of Maritime Safety Policy Instruments

Maritime safety is an issue that has gained a lot of attention in the Baltic Sea area due to the dense maritime traffic and transportation of oil in the area. Lots of effort has been paid to enhance maritime safety in the area. The risk exists that excessive legislation and other requirements mean more costs for limited benefit. In order to utilize both public and private resources efficiently, awareness is required of what kind of costs maritime safety policy instruments cause and whether the costs are in relation to benefits. The aim of this report is to present an overview of the cost-effectiveness of maritime safety policy instruments focusing on the cost aspect: what kind of costs maritime safety policy causes, to whom, what affects the cost-effectiveness and how cost-effectiveness is studied. The study is based on a literature review and on the interviews of Finnish maritime experts. The results of this study imply that cost-effectiveness is a complicated issue to evaluate. There are no uniform practices for which costs and benefits should be included in the evaluation and how they should be valued. One of the challenges is how to measure costs and benefits during the course of a longer time period. Often a lack of data erodes the reliability of evaluation. In the prevention of maritime accidents, costs typically include investments in ship structures or equipment, as well as maintenance and labor costs. Also large investments may be justifiable if they respectively provide significant improvements to maritime safety. Measures are cost-effective only if they are implemented properly. Costeffectiveness is decreased if a measure causes overlapping or repetitious work. Costeffectiveness is also decreased if the technology isn’t user-friendly or if it is soon replaced with a new technology or another new appliance. In future studies on the cost-effectiveness of maritime safety policy, it is important to acknowledge the dependency between different policy instruments and the uncertainty of the factors affecting cost-effectiveness. The costs of a single measure are rarely relatively significant and the effect of each measure on safety tends to be positive. The challenge is to rank the measures and to find the most effective combination of different policy instruments. The greatest potential offered for the analysis of cost-effectiveness of individual measures is their implementation in clearly defined risk situations, in which different measures are truly alternative to each other. Overall, maritime safety measures do not seem to be considered burdening for the shipping industry in Finland at the moment. Generally actors in the Finnish shipping industry seem to find maintaining a high safety level important and act accordingly.

The effect of shielding gas feeding method in laser welding of steel

Gas shielding plays an important role in laser welding phenomena. This is because it does not only provide shielding against oxidization but it has an effect in beam absorption and thus welds penetration. The goal of this thesis is to study and compare the effects of different shielding gas feeding methods in laser welding of steel. Research method is a literature survey. It is found that the inclination angle and the arrangement of the gas feeding nozzles affect the phenomena significantly. It is suggested that by designing shielding gas feeding case specifically better welding results can be obtained.

CTQ process flow development and the impact for cost of quality

Tämä työ tehtiin Kone Industrial Oy:lle Major Projects yksikköön, laatuosastolle. Kone Major Projects yksikkö keskittyy erikoisiin ja suuriin hissi- ja liukuporras projekteihin. Työn tavoitteena oli luoda harmonisoitu prosessi hissikomponenttien laaduntarkkailua varten sekä tarkastella ja vertailla kustannussäästöjä, jota tällä uudella prosessilla voidaan saavuttaa. Tavoitteena oli saavuttaa 80-prosentin kustannussäästöt laatukustannuksissa uuden laatuprosessin avulla. Työn taustana ja tutkimusongelmana ovat lisääntyneet erikoisprojektit ja niiden myötä lisääntynyt laaduntarkkailun tarve. Ongelmana laaduntarkkailussa voitiin pitää harmonisoidun ja selkeän prosessin puuttumista C-prosessikomponenttien valmistuksessa. Lisäksi kehitysprosessin aikana luotiin vanhojen työkalujen pohjalta keskeinen laaduntarkkailutyökalu, CTQ-työkalu. Työssä käsitellään ensin Konetta yhtiönä ja selvitetään Koneen keskeisimmät prosessit työn taustaksi. Teoria osuudessa käsitellään prosessin kehitykseen liittyviä teorioita sekä yleisiä laatukäsitteitä ja esitetään teorioita laadun asemasta nykypäivänä. Lopuksi käsitellään COQ eli laatukustannusten teoriaa ja esitellään teoria PAF-analyysille, jota käytetään työssä laatukustannusten vertailuun case esimerkin avulla. Työssä kuvataan CTQ prosessin luominen alusta loppuun ja case esimerkin avulla testataan uutta CTQ prosessia pilottihankkeessa. Tässä case esimerkissä projektin bracket eli johdekiinnitysklipsi tuotetaan uuden laatuprosessin avulla sekä tehdään kustannusvertailu saman projektin toisen bracketin kanssa, joka on tuotettu ennen uuden laatuprosessin implementoimista. Työn lopputuloksena CTQ prosessi saatiin luotua ja sitä pystyttiin testaamaan käytännössä case esimerkin avulla. Tulosten perusteella voidaan sanoa, että CTQ prosessin käyttö vähentää laatukustannuksia huomattavasti ja helpottaa laadunhallintaa C-prosessikomponenttien tuotannossa.

Validation and Selection of Transportation Cost Drivers with Advanced Methods

In today's logistics environment, there is a tremendous need for accurate cost information and cost allocation. Companies searching for the proper solution often come across with activity-based costing (ABC) or one of its variations which utilizes cost drivers to allocate the costs of activities to cost objects. In order to allocate the costs accurately and reliably, the selection of appropriate cost drivers is essential in order to get the benefits of the costing system. The purpose of this study is to validate the transportation cost drivers of a Finnish wholesaler company and ultimately select the best possible driver alternatives for the company. The use of cost driver combinations as an alternative is also studied. The study is conducted as a part of case company's applied ABC-project using the statistical research as the main research method supported by a theoretical, literature based method. The main research tools featured in the study include simple and multiple regression analyses, which together with the literature and observations based practicality analysis forms the basis for the advanced methods. The results suggest that the most appropriate cost driver alternatives are the delivery drops and internal delivery weight. The possibility of using cost driver combinations is not suggested as their use doesn't provide substantially better results while increasing the measurement costs, complexity and load of use at the same time. The use of internal freight cost drivers is also questionable as the results indicate weakening trend in the cost allocation capabilities towards the end of the period. Therefore more research towards internal freight cost drivers should be conducted before taking them in use.

Cost-benefit analysis of using test automation in the development of embedded software

The goal of this thesis is to make a case study of test automation’s profitability in the development of embedded software in a real industrial setting. The cost-benefit analysis is done by considering the costs and benefits test automation causes to software development, before the software is released to customers. The potential benefits of test automation regarding software quality after customer release were not estimated. Test automation is a significant investment which often requires dedicated resources. When done accordingly, the investment in test automation can produce major cost savings by reducing the need for manual testing effort, especially if the software is developed with an agile development framework. It can reduce the cost of avoidable rework of software development, as test automation enables the detection of construction time defects in the earliest possible moment. Test automation also has many pitfalls such as test maintainability and testability of the software, and if those areas are neglected, the investment in test automation may become worthless or it may even produce negative results. The results of this thesis suggest that test automation is very profitable at the company under study.

European luxury brands made in China: the effect of low-cost country manufacturing on brand image and purchase decisions

European luxury brands have an image of manufacturing their products in the same country where the brands originate. However, in the past years many luxury brands have shifted their manufacturing to countries outside Europe. China is now a common manufacturing country for European luxury brands despite the country’s poor image as a manufacturer. Chinese manufacturing is often associated with bad quality, bad labour conditions, mass production, and counterfeits. The image of China does not quite match the image luxury brands enjoy including characteristics such as high end quality, craftsmanship, details, design, or premium price. A negatively perceived country-of-manufacture may have an effect on a brand’s image and consumers’ purchase decisions. This thesis is focused on European luxury brands manufacturing in China, and how this effects the brand image and purchase decisions among luxury consumers. The empirical part of this thesis is based on focus group research, which is a popular method in the field of qualitative research. The main focus group is female luxury consumers in Finland. This main group has been divided into three categories: 1) the university students, 2) the young career women, 3) the experienced luxury consumers. This categorization has been done based on their different stages in luxury consumption. All in all, the empirical research consisted of 11 interviews and 29 participants. The main contribution of this thesis was that there is a difference between the opinions of the younger groups (university students and young career women) and the experienced luxury consumers when discussing the effect of country-of-manufacture on brand image and purchase decisions of luxury brands. The younger participants thought that manufacturing luxury products in China might affect the brand image, but their purchase decisions would not be that much affected by the country-of-origin. The experienced luxury consumers had quite a different view on the country-of-origin of luxury brands – they found it an important decisive factor prior making purchases. The majority of experienced luxury consumers would not buy luxury products made in China, and they would always check where these products are made in.

Cost-efficient virtual machine management : provisioning, admission control, and consolidation

One of the main challenges in Software Engineering is to cope with the transition from an industry based on software as a product to software as a service. The field of Software Engineering should provide the necessary methods and tools to develop and deploy new cost-efficient and scalable digital services. In this thesis, we focus on deployment platforms to ensure cost-efficient scalability of multi-tier web applications and on-demand video transcoding service for different types of load conditions. Infrastructure as a Service (IaaS) clouds provide Virtual Machines (VMs) under the pay-per-use business model. Dynamically provisioning VMs on demand allows service providers to cope with fluctuations on the number of service users. However, VM provisioning must be done carefully, because over-provisioning results in an increased operational cost, while underprovisioning leads to a subpar service. Therefore, our main focus in this thesis is on cost-efficient VM provisioning for multi-tier web applications and on-demand video transcoding. Moreover, to prevent provisioned VMs from becoming overloaded, we augment VM provisioning with an admission control mechanism. Similarly, to ensure efficient use of provisioned VMs, web applications on the under-utilized VMs are consolidated periodically. Thus, the main problem that we address is cost-efficient VM provisioning augmented with server consolidation and admission control on the provisioned VMs. We seek solutions for two types of applications: multi-tier web applications that follow the request-response paradigm and on-demand video transcoding that is based on video streams with soft realtime constraints. Our first contribution is a cost-efficient VM provisioning approach for multi-tier web applications. The proposed approach comprises two subapproaches: a reactive VM provisioning approach called ARVUE and a hybrid reactive-proactive VM provisioning approach called Cost-efficient Resource Allocation for Multiple web applications with Proactive scaling. Our second contribution is a prediction-based VM provisioning approach for on-demand video transcoding in the cloud. Moreover, to prevent virtualized servers from becoming overloaded, the proposed VM provisioning approaches are augmented with admission control approaches. Therefore, our third contribution is a session-based admission control approach for multi-tier web applications called adaptive Admission Control for Virtualized Application Servers. Similarly, the fourth contribution in this thesis is a stream-based admission control and scheduling approach for on-demand video transcoding called Stream-Based Admission Control and Scheduling. Our fifth contribution is a computation and storage trade-o strategy for cost-efficient video transcoding in cloud computing. Finally, the sixth and the last contribution is a web application consolidation approach, which uses Ant Colony System to minimize the under-utilization of the virtualized application servers.

Utilization of steelmaking waste materials for production of calcium carbonate (CaCO3)

The steel industry produces, besides steel, also solid mineral by-products or slags, while it emits large quantities of carbon dioxide (CO2). Slags consist of various silicates and oxides which are formed in chemical reactions between the iron ore and the fluxing agents during the high temperature processing at the steel plant. Currently, these materials are recycled in the ironmaking processes, used as aggregates in construction, or landfilled as waste. The utilization rate of the steel slags can be increased by selectively extracting components from the mineral matrix. As an example, aqueous solutions of ammonium salts such as ammonium acetate, chloride and nitrate extract calcium quite selectively already at ambient temperature and pressure conditions. After the residual solids have been separated from the solution, calcium carbonate can be precipitated by feeding a CO2 flow through the solution. Precipitated calcium carbonate (PCC) is used in different applications as a filler material. Its largest consumer is the papermaking industry, which utilizes PCC because it enhances the optical properties of paper at a relatively low cost. Traditionally, PCC is manufactured from limestone, which is first calcined to calcium oxide, then slaked with water to calcium hydroxide and finally carbonated to PCC. This process emits large amounts of CO2, mainly because of the energy-intensive calcination step. This thesis presents research work on the scale-up of the above-mentioned ammonium salt based calcium extraction and carbonation method, named Slag2PCC. Extending the scope of the earlier studies, it is now shown that the parameters which mainly affect the calcium utilization efficiency are the solid-to-liquid ratio of steel slag and the ammonium salt solvent solution during extraction, the mean diameter of the slag particles, and the slag composition, especially the fractions of total calcium, silicon, vanadium and iron as well as the fraction of free calcium oxide. Regarding extraction kinetics, slag particle size, solid-to-liquid ratio and molar concentration of the solvent solution have the largest effect on the reaction rate. Solvent solution concentrations above 1 mol/L NH4Cl cause leaching of other elements besides calcium. Some of these such as iron and manganese result in solution coloring, which can be disadvantageous for the quality of the PCC product. Based on chemical composition analysis of the produced PCC samples, however, the product quality is mainly similar as in commercial products. Increasing the novelty of the work, other important parameters related to assessment of the PCC quality, such as particle size distribution and crystal morphology are studied as well. As in traditional PCC precipitation process, the ratio of calcium and carbonate ions controls the particle shape; a higher value for [Ca2+]/[CO32-] prefers precipitation of calcite polymorph, while vaterite forms when carbon species are present in excess. The third main polymorph, aragonite, is only formed at elevated temperatures, above 40-50 °C. In general, longer precipitation times cause transformation of vaterite to calcite or aragonite, but also result in particle agglomeration. The chemical equilibrium of ammonium and calcium ions and dissolved ammonia controlling the solution pH affects the particle sizes, too. Initial pH of 12-13 during the carbonation favors nonagglomerated particles with a diameter of 1 μm and smaller, while pH values of 9-10 generate more agglomerates of 10-20 μm. As a part of the research work, these findings are implemented in demonstrationscale experimental process setups. For the first time, the Slag2PCC technology is tested in scale of ~70 liters instead of laboratory scale only. Additionally, design of a setup of several hundreds of liters is discussed. For these purposes various process units such as inclined settlers and filters for solids separation, pumps and stirrers for material transfer and mixing as well as gas feeding equipment are dimensioned and developed. Overall emissions reduction of the current industrial processes and good product quality as the main targets, based on the performed partial life cycle assessment (LCA), it is most beneficial to utilize low concentration ammonium salt solutions for the Slag2PCC process. In this manner the post-treatment of the products does not require extensive use of washing and drying equipment, otherwise increasing the CO2 emissions of the process. The low solvent concentration Slag2PCC process causes negative CO2 emissions; thus, it can be seen as a carbon capture and utilization (CCU) method, which actually reduces the anthropogenic CO2 emissions compared to the alternative of not using the technology. Even if the amount of steel slag is too small for any substantial mitigation of global warming, the process can have both financial and environmental significance for individual steel manufacturers as a means to reduce the amounts of emitted CO2 and landfilled steel slag. Alternatively, it is possible to introduce the carbon dioxide directly into the mixture of steel slag and ammonium salt solution. The process would generate a 60-75% pure calcium carbonate mixture, the remaining 25-40% consisting of the residual steel slag. This calcium-rich material could be re-used in ironmaking as a fluxing agent instead of natural limestone. Even though this process option would require less process equipment compared to the Slag2PCC process, it still needs further studies regarding the practical usefulness of the products. Nevertheless, compared to several other CO2 emission reduction methods studied around the world, the within this thesis developed and studied processes have the advantage of existing markets for the produced materials, thus giving also a financial incentive for applying the technology in practice.

Atrial natriuretic peptide and feeding activity patterns in rats

This review presents historical data about atrial natriuretic peptide (ANP) from its discovery as an atrial natriuretic factor (ANF) to its role as an atrial natriuretic hormone (ANH). As a hormone, ANP can interact with the hypothalamic-pituitary-adrenal axis (HPA-A) and is related to feeding activity patterns in the rat. Food restriction proved to be an interesting model to investigate this relationship. The role of ANP must be understood within a context of peripheral and central interactions involving different peptides and pathways