Uniquely Identifiable Tamper-Evident Device Using Coupling between Subwavelength Gratings

Reliability and sensitive information protection are critical aspects of integrated circuits. A novel technique using near-field evanescent wave coupling from two subwavelength gratings (SWGs), with the input laser source delivered through an optical fiber is presented for tamper evidence of electronic components. The first grating of the pair of coupled subwavelength gratings (CSWGs) was milled directly on the output facet of the silica fiber using focused ion beam (FIB) etching. The second grating was patterned using e-beam lithography and etched into a glass substrate using reactive ion etching (RIE). The slightest intrusion attempt would separate the CSWGs and eliminate near-field coupling between the gratings. Tampering, therefore, would become evident. Computer simulations guided the design for optimal operation of the security solution. The physical dimensions of the SWGs, i.e. period and thickness, were optimized, for a 650 nm illuminating wavelength. The optimal dimensions resulted in a 560 nm grating period for the first grating etched in the silica optical fiber and 420 nm for the second grating etched in borosilicate glass. The incident light beam had a half-width at half-maximum (HWHM) of at least 7 µm to allow discernible higher transmission orders, and a HWHM of 28 µm for minimum noise. The minimum number of individual grating lines present on the optical fiber facet was identified as 15 lines. Grating rotation due to the cylindrical geometry of the fiber resulted in a rotation of the far-field pattern, corresponding to the rotation angle of moiré fringes. With the goal of later adding authentication to tamper evidence, the concept of CSWGs signature was also modeled by introducing random and planned variations in the glass grating. The fiber was placed on a stage supported by a nanomanipulator, which permitted three-dimensional displacement while maintaining the fiber tip normal to the surface of the glass substrate. A 650 nm diode laser was fixed to a translation mount that transmitted the light source through the optical fiber, and the output intensity was measured using a silicon photodiode. The evanescent wave coupling output results for the CSWGs were measured and compared to the simulation results.

All-analogue real-time filter bank OFDM over 50 Km of SSMF using a novel synchronization technique

A 21.6 Gbit/s 1.78 bit/s/Hz OFDM signal is transmitted over 50 Km of fiber without using DSP in the transmitter or the receiver. The synchronization scheme only requires one PLL to synchronize all the subcarriers.

Experimental comparison of artificial neural network and volterra based nonlinear equalization for CO-OFDM

A novel artificial neural network (ANN)-based nonlinear equalizer (NLE) of low complexity is demonstrated for 40-Gb/s CO-OFDM at 2000 km, revealing ∼1.5 dB enhancement in Q-factor compared to inverse Volterra-series transfer function based NLE.

Efficient Computation of Electromagnetic Waves in Hydrocarbon Exploration Using the Improved Numerical Mode Matching (NMM) Method

In this study, we developed and improved the numerical mode matching (NMM) method which has previously been shown to be a fast and robust semi-analytical solver to investigate the propagation of electromagnetic (EM) waves in an isotropic layered medium. The applicable models, such as cylindrical waveguide, optical fiber, and borehole with earth geological formation, are generally modeled as an axisymmetric structure which is an orthogonal-plano-cylindrically layered (OPCL) medium consisting of materials stratified planarly and layered concentrically in the orthogonal directions.

In this report, several important improvements have been made to extend applications of this efficient solver to the anisotropic OCPL medium. The formulas for anisotropic media with three different diagonal elements in the cylindrical coordinate system are deduced to expand its application to more general materials. The perfectly matched layer (PML) is incorporated along the radial direction as an absorbing boundary condition (ABC) to make the NMM method more accurate and efficient for wave diffusion problems in unbounded media and applicable to scattering problems with lossless media. We manipulate the weak form of Maxwell's equations and impose the correct boundary conditions at the cylindrical axis to solve the singularity problem which is ignored by all previous researchers. The spectral element method (SEM) is introduced to more efficiently compute the eigenmodes of higher accuracy with less unknowns, achieving a faster mode matching procedure between different horizontal layers. We also prove the relationship of the field between opposite mode indices for different types of excitations, which can reduce the computational time by half. The formulas for computing EM fields excited by an electric or magnetic dipole located at any position with an arbitrary orientation are deduced. And the excitation are generalized to line and surface current sources which can extend the application of NMM to the simulations of controlled source electromagnetic techniques. Numerical simulations have demonstrated the efficiency and accuracy of this method.

Finally, the improved numerical mode matching (NMM) method is introduced to efficiently compute the electromagnetic response of the induction tool from orthogonal transverse hydraulic fractures in open or cased boreholes in hydrocarbon exploration. The hydraulic fracture is modeled as a slim circular disk which is symmetric with respect to the borehole axis and filled with electrically conductive or magnetic proppant. The NMM solver is first validated by comparing the normalized secondary field with experimental measurements and a commercial software. Then we analyze quantitatively the induction response sensitivity of the fracture with different parameters, such as length, conductivity and permeability of the filled proppant, to evaluate the effectiveness of the induction logging tool for fracture detection and mapping. Casings with different thicknesses, conductivities and permeabilities are modeled together with the fractures in boreholes to investigate their effects for fracture detection. It reveals that the normalized secondary field will not be weakened at low frequencies, ensuring the induction tool is still applicable for fracture detection, though the attenuation of electromagnetic field through the casing is significant. A hybrid approach combining the NMM method and BCGS-FFT solver based integral equation has been proposed to efficiently simulate the open or cased borehole with tilted fractures which is a non-axisymmetric model.

Integrated System Technologies for Modular Trapped Ion Quantum Information Processing

Although trapped ion technology is well-suited for quantum information science, scalability of the system remains one of the main challenges. One of the challenges associated with scaling the ion trap quantum computer is the ability to individually manipulate the increasing number of qubits. Using micro-mirrors fabricated with micro-electromechanical systems (MEMS) technology, laser beams are focused on individual ions in a linear chain and steer the focal point in two dimensions. Multiple single qubit gates are demonstrated on trapped 171Yb+ qubits and the gate performance is characterized using quantum state tomography. The system features negligible crosstalk to neighboring ions (< 3e-4), and switching speeds comparable to typical single qubit gate times (< 2 us). In a separate experiment, photons scattered from the 171Yb+ ion are coupled into an optical fiber with 63% efficiency using a high numerical aperture lens (0.6 NA). The coupled photons are directed to superconducting nanowire single photon detectors (SNSPD), which provide a higher detector efficiency (69%) compared to traditional photomultiplier tubes (35%). The total system photon collection efficiency is increased from 2.2% to 3.4%, which allows for fast state detection of the qubit. For a detection beam intensity of 11 mW/cm2, the average detection time is 23.7 us with 99.885(7)% detection fidelity. The technologies demonstrated in this thesis can be integrated to form a single quantum register with all of the necessary resources to perform local gates as well as high fidelity readout and provide a photon link to other systems.

Exploring a new transmission window for telecommunications in the 2 μm waveband

In this paper, we will demonstrate the possibility of opening a new telecommunications transmission window around the 2 μm wavelength, in order to exploit the potential low loss of hollow-core photonic bandgap fibers, with the benefits of significantly lower non-linearity and latency. We will show recent efforts developing a dense wavelength division multiplexing testbed at this waveband, with 100 GHz spacing wavelength channels and 105 Gbit/s total capacity achieved.

Développement de fibres optiques composites pour la génération du supercontinuum dans l’infrarouge

Les sources laser à large bande possédant les caractéristiques requises pour émettre sur la plage spectrale correspondant à la seconde fenêtre de transmission atmosphérique (3 à 5 μm) exercent un attrait considérable pour divers domaines tels que la télédétection de polluants atmosphériques et les contremesures infrarouges. Les supercontinua générés à l’intérieur de fibres optiques représentent une option intéressante pour réaliser ce type de sources laser. En effet, ils possèdent une intensité élevée, un large contenu spectral, une excellente directionnalité de faisceau, ainsi qu’un bon potentiel pour constituer des sources lumineuses compactes et robustes. Toutefois, la génération d’un tel supercontinuum implique certains défis à relever sur le plan de la conception des fibres optiques employées. En fait, ces fibres optiques doivent présenter de faibles pertes de propagation sur la plage spectrale de 3 à 5 μm, posséder un paramètre de non-linéarité élevé et permettre le pompage en régime anomal de dispersion à des longueurs d’onde pour lesquelles des sources laser compactes sont offertes commercialement. En matière de robustesse, ces fibres doivent également démontrer de bonnes propriétés mécaniques ainsi qu’une stabilité chimique appropriée vis-à-vis de la corrosion causée par l’humidité. Dans le cadre de cette thèse, un nouveau type de fibres composites à saut d’indice fortement contrasté a été développé pour atteindre ces objectifs de génération de supercontinuum. Ce type de fibres combine respectivement un verre de tellurite et un verre de germanate pour son coeur et sa gaine permettant ainsi d’atteindre une différence d’indice de réfraction d’environ 0.3 entre ces deux dernières structures. Grâce à cet important saut d’indice, ces fibres peuvent fortement confiner les modes optiques à l’intérieur de leur coeur, ce qui leur donne la possibilité d’atteindre un niveau élevé de non-linéarité et d’optimiser leurs caractéristiques de dispersion chromatique pour la génération du supercontinuum. D’autre part, leur section transversale toute solide leur confère aussi une meilleure stabilité environnementale comparativement à celle démontrée par les fibres optiques microstructurées à base de verres d’oxydes de métaux lourds, de verres de chalcogénure et de verres fluorés. Toutefois, leur fabrication nécessite l’appariement de verres dont les propriétés thermomécaniques concordent suffisamment ensemble pour permettre leur fibrage. Les travaux effectués ici démontrent la production de fibres optiques composites et leur potentiel pour la génération du supercontinuum dans l’infrarouge moyen.

Geophysics: Principles, applications and emerging technologies

This book presents research in the field of Geophysics, particularly referring to principles, applications and emerging technologies. Table of Contents: Preface pp. i-xxi Environmental Geophysics: Techniques, advantages and limitations (Pantelis Soupios and Eleni Kokinou, Department of Environmental and Natural Resources Engineering, Technological Educational Institute of Crete, Dynamics of the Ocean Floor, Helmholtz Centre for Ocean Research Kiel, Geomar)pp i-xxi Application of Innovative Geophysical Techniques in Coastal Areas (V. Di Fiore, M. Punzo, D. Tarallo, and G. Cavuoto, Institute for Marine Coastal Environment, National Research Council, Naples)pp. i-xxi Marine Geophysics of the Naples Bay (Southern Tyrrhenian sea, Italy): Principles, Applications and Emerging Technologies (Gemma Aiello and Ennio Marsella, Institute for Marine Coastal Environment, National Research Council, Naples)pp. i-xxi Oceanic Oscillation Phenomena: Relation to Synchronization and Stochastic Resonance (Shinya Shimokawa and Tomonori Matsuura, National Research Institute for Earth Science and Disaster Prevention, Univ. of Toyama)pp. i-xxi Assessment of ocean variability in the Sicily Channel from a numerical three-dimensional model using EOFs decomposition (R. Sorgente, A. Olita, A.F. Drago, A. Ribotti, L. Fazioli, and C. Tedesco, Institute for Marine Coastal Environment, National Research Council, Oristano)pp. i-xxi Monitoring Test of Crack Opening in Volcanic Tuff (Coroglio Cliff. Italy) Using Distributed Optical Fiber Sensor (A. Minardo, A. Coscetta, M. Caccavale, G. Esposito, F. Matano, M. Sacchi, R. Somma, G. Zeni, and L. Zeni, Department of Industrial and Information Eng., Second University of Naples Aversa, Institute for Marine Coastal Environment, National Research Council Naples, National Institute for Geophysics and Volcanology, Osservatorio Vesuviano Naples, Institute for Electromagnetic Sensing of the Environment, National Research Council Naples)pp. i-xxi

Desenvolvimento e caracterização de sensores óticos de qualidade de líquidos

A necessidade de controlar de forma rápida, eficaz e precisa a qualidade de líquidos, principalmente a água, um bem essencial para os seres humanos, conduziu ao desenvolvimento de dispositivos capazes de relacionar a medição de parâmetros físicos com a qualidade da água. Estes dispositivos devem ser capazes de monitorizar os inúmeros parâmetros necessários para aferir a qualidade do líquido, como a turvação, índice de refração, concentração de sedimentos e propriedades cromáticas. Desta forma devem-se recorrer a sensores multiparâmetros. A tecnologia baseada em POF (fibra ótica polimérica) tem sido apontada com elevado potencial no desenvolvimento de sensores óticos nas mais variadas aplicações dado o seu baixo custo, imunidade a interferências eletromagnéticas e flexibilidade. Neste trabalho é proposto um sensor POF multiparâmetro capaz de reunir num único dispositivo a capacidade de medição de altos e baixos valores de turvação, assim como ter a capacidade de medir vários parâmetros em simultâneo e em tempo real. Os resultados permitem avaliar o aumento da capacidade de gama dinâmica de turvação e concentração de sedimentos face aos sensores multiparâmetros já comercializados, uma vez que houve uma boa resposta por parte do sensor para altos e para baixos valores. Um método utilizado para descorrelacionar os diferentes parâmetros foi aplicado com sucesso. A WATGRID LDA. pretende, partindo deste tipo de sensores, disponibilizar aos seus clientes soluções (plataformas) inteligentes e integradas para avaliação e gestão da qualidade dos líquidos para consumo (e.g. água e vinho). Estas soluções irão permitir que os clientes da WATGRID LDA. aumentem a sua eficiência, a qualidade do seu produto e tenham um maior controlo do processo ao mesmo tempo que reduzem custos.

Caracterização in vitro de um dosímetro de fibra ótica para braquiterapia de HDR

Recentemente foi desenvolvido um dosímetro baseado em fibras cintilantes (BCF-12 da companhia Saint Gobain Crystals com 1 e 0,5 mm de diâmetro e 5 mm de comprimento) para braquiterapia de baixa taxa de dose, em particular a braquiterapia direcionada para o tratamento do cancro da próstata. Este utiliza um novo fotomultiplicador de estado sólido dado pelo nome de MPPC - MultiPixel Photon Counter da companhia Hamamatsu Photonics (Japão). Nesta dissertação é estudado o mesmo dosímetro para a modalidade de braquiterapia de elevada taxa de dose (HDR). A informação sobre a dose neste tipo de dosímetros é obtida a partir de sinais óticos (em vez de sinais elétricos), que são imunes a interferências elétricas e eletromagnéticas. Adicionalmente as pequenas dimensões das fibras oferecem uma excelente resolução espacial e uma invasão mínima para uso em dosimetria in vivo, permitindo medir a dose diretamente ou próximo ao tumor e em tempo real. A sua utilização em braquiterapia para o cancro da próstata constitui-se assim como uma vantagem, uma vez que as fibras podem ser inseridas diretamente nos aplicadores utilizados neste tipo de tratamentos. Apesar de tudo, este tipo de dosímetros possui algumas desvantagens, como por exemplo a luz de Cherenkov e a fluorescência (forma de ruído dada pelo nome de stem effect) que, e a contrário da luz produzida pela fibra cintilante, não são diretamente proporcionais à energia depositada. Contudo, e para energias praticadas em braquiterapia de HDR, nesta dissertação, mostrou-se que este problema é pouco significativo dado que a percentagem de contribuição destes efeitos para o sinal medido é menor que 1% (ou 5% para distâncias menores que 25 mm). Ao longo desta dissertação é feita a caraterização do dosímetro (em modo corrente e impulso) e das suas várias partes em ambiente de laboratório e clínico. Nestes estudos o dosímetro, além de exibir uma boa reprodutibilidade (variação máxima de 3% entre medidas), mostrou uma alta linearidade para uma ampla gama de doses, assim como uma sensibilidade (µGy) semelhante à de uma câmara de ionização, tornando-o adequado para braquiterapia de HDR (tratamento que envolve altos gradientes de dose). Complementarmente, a sua grande versatilidade e simples utilização possibilita a sua aplicação prática em outras modalidades radioterapêuticas.

Caracterização do ciclo da marcha em amputado transtibial com prótese inteligente

This work presents an application of optical fiber sensors based on Bragg gratings integrated to a transtibial prosthesis tube manufactured with a polymeric composite systrem of epoxy resin reinforced with glass fiber. The main objective of this study is to characterize the sensors applied to the gait cycle and changes in the gravity center of a transtibial amputee, trough the analysis of deformation and strengh of the transtibial prosthesis tube. For this investigation it is produced a tube of the composite material described above using the molding method of resin transfer (RTM) with four optical sensors. The prosthesis in which the original tube is replaced is classified as endoskeletal, has vacuum fitting, aluminium conector tube and carbon fiber foot cushioning. The volunteer for the tests was a man of 41 years old, 1.65 meters tall, 72 kilograms and left-handed. His amputation occurred due to trauma (surgical section is in the medial level, and was made below the left lower limb knee). He has been a transtibial prosthesis user for two years and eight months. The characterization of the optical sensors and analysis of mechanical deformation and tube resistance occurred through the gait cycle and the variation of the center of gravity of the body by the following tests: stand up, support leg without the prosthesis, support in the leg with the prosthesis, walk forward and walk backward. Besides the characterization of optical sensors during the gait cycle and the variation of the gravity center in a transtibial amputated, the results also showed a high degree of integration of the sensors in the composite and a high mechanical strength of the material.

Análise de conversores de frequência óptica baseados em amplificadores ópticos semicondutores

Dissertação de mest. em Engenharia de Sistemas e Computação, Faculdade de Ciências e Tecnologia, Univ. do Algarve, 2002

Construção de um aparato experimental para monitoramento in situ da deposição de filmes finos de titânio por magnetron sputtering

The technique of surface coating using magnetron sputtering is one of the most widely used in the surface engineering, for its versatility in obtaining different films as well as in the micro / nanometric thickness control. Among the various process parameters, those related to the active species of the plasma are of the most fundamental importance in the mechanism and kinetics of deposition. In order to identify the active species of the plasma, parameters such as gas flow, pressure and density of electric power were varied during titanium coating on glass substrate. By flowing argon gas of 10, 20, 30, 40 and 50 sccm (cubic centimeters per minute) for each gas flow a sequential scan of the electric current of 0.10, 0.20, 0.30, 0.40 , 0.50 A. The maximum value of 0.50 A was chosen based both on literature data and on limitations of the equipment. The monitoring of plasma species present during the deposition was carried out in situ by the technique of optical emission spectroscopy (OES) through the spectrometer Ocean Optics USB2000 Series. For this purpose, an apparatus was developed to adapt the OES inside the plasma reactor to stay positioned closest to the target. The radiations emitted by the species were detected by an optical fiber placed behind the glass substrate and their intensities as a function of wavelength were, displayed on a monitor screen. The acquisition time for each condition of the plain parameters was related to the minima of spectral lines intensities due to the film formed on the substrate. The intensities of different emission lines of argon and titanium were then analyzed as a function of time, to determine the active species and estimate the thickness of the deposited films. After the deposition, the coated glasses thin films were characterized by optical transmittance through an infrared laser. It was found that the thickness and deposition rate determined by in situ analysis were consistent with the results obtained by laser transmittance

Libs in cultural heritage: recognition and identification of objects in an underwater archaeological shipwreck

Nowadays, one of the most important areas of interest in archeology is the characterization of the submersed cultural heritage. Mediterranean Sea is rich in archaeological findings due to storms, accidents and naval battles since prehistoric times. Chemical analysis of submerged materials is an extremely valuable source of information on the origin and precedence of the wrecks, and also the raw materials employed during the manufacturing of the objects found in these sites. Nevertheless, sometimes it is not possible to extract the archaeological material from the marine environment due to size of the sample, the legislation or preservation purposes. In these cases, the in-situ analysis turns into the only alternative for obtaining information. In spite of this demand, no analytical techniques are available for the in-situ chemical characterization of underwater materials. The versatility of laser-induced breakdown spectroscopy (LIBS) has been successfully tested in oceanography 1. Advantages such as rapid and in situ analysis with no sample preparation make LIBS a suitable alternative for field measurements. To further exploit the inherent advantages of the technology, a mobile fiber-based LIBS platform capable of performing remote measurements up to 50 meters range has been designed for the recognition and identification of artworks in underwater archaeological shipwrecks. The LIBS prototype featured both single-pulse (SP-LIBS) and multi-pulse excitation (MP-LIBS) 2. The use of multi-pulse excitation allowed an increased laser beam energy (up to 95 mJ) transmitted through the optical fiber. This excitation mode results in an improved performance of the equipment in terms of extended range of analysis (to a depth of 50 m) and a broader variety of samples to be analyzed (i.e., rocks, marble, ceramics and concrete). In the present work, the design and construction considerations of the instrument are reported and its performance is discussed on the basis of the spectral response, the remote irradiance achieved upon the range of analysis and its influence on plasma properties, as well as the effect of the laser pulse duration and purge gas to the LIBS signal. Also, to check the reliability and reproducibility of the instrument for field analysis several robustness tests were performed outside the lab. Finally, the capability of this instrument was successfully demonstrated in an underwater archaeological shipwreck (San Pedro de Alcántara, Malaga).

Amplification d’impulsions brèves de haute énergie par effet Raman stimulé dans les fibres optiques

Le développement au cours des dernières décennies de lasers à fibre à verrouillage de modes permet aujourd’hui d’avoir accès à des sources fiables d’impulsions femtosecondes qui sont utilisées autant dans les laboratoires de recherche que pour des applications commerciales. Grâce à leur large bande passante ainsi qu’à leur excellente dissipation de chaleur, les fibres dopées avec des ions de terres rares ont permis l’amplification et la génération d’impulsions brèves de haute énergie avec une forte cadence. Cependant, les effets non linéaires causés par la faible taille du faisceau dans la fibre ainsi que la saturation de l’inversion de population du milieu compliquent l’utilisation d’amplificateurs fibrés pour l’obtention d’impulsions brèves dont l’énergie dépasse le millijoule. Diverses stratégies comme l’étirement des impulsions à des durées de l’ordre de la nanoseconde, l’utilisation de fibres à cristaux photoniques ayant un coeur plus large et l’amplification en parallèle ont permis de contourner ces limitations pour obtenir des impulsions de quelques millijoules ayant une durée inférieure à la picoseconde. Ce mémoire de maîtrise présente une nouvelle approche pour l’amplification d’impulsions brèves utilisant la diffusion Raman des verres de silice comme milieu de gain. Il est connu que cet effet non linéaire permet l’amplification avec une large bande passante et ce dernier est d’ailleurs couramment utilisé aujourd’hui dans les réseaux de télécommunications par fibre optique. Puisque l’adaptation des schémas d’amplification Raman existants aux impulsions brèves de haute énergie n’est pas directe, on propose plutôt un schéma consistant à transférer l’énergie d’une impulsion pompe quasi monochromatique à une impulsion signal brève étirée avec une dérive en fréquence. Afin d’évaluer le potentiel du gain Raman pour l’amplification d’impulsions brèves, ce mémoire présente un modèle analytique permettant de prédire les caractéristiques de l’impulsion amplifiée selon celles de la pompe et le milieu dans lequel elles se propagent. On trouve alors que la bande passante élevée du gain Raman des verres de silice ainsi que sa saturation inhomogène permettent l’amplification d’impulsions signal à une énergie comparable à celle de la pompe tout en conservant une largeur spectrale élevée supportant la compression à des durées très brèves. Quelques variantes du schéma d’amplification sont proposées, et leur potentiel est évalué par l’utilisation du modèle analytique ou de simulations numériques. On prédit analytiquement et numériquement l’amplification Raman d’impulsions à des énergies de quelques millijoules, dont la durée est inférieure à 150 fs et dont la puissance crête avoisine 20 GW.