Multi-component quantitation of loratadine, pseudoephedrine and paracetamol in plasma and pharmaceutical formulations with liquid chromatography-tandem mass spectrometry utilizing a monolithic column

The purpose of this study was to develop a rapid, simple and sensitive quantitation method for pseudoephedrine (PSE), paracetamol (PAR) and loratadine (LOR) in plasma and pharmaceuticals using liquid chromatography-tandem mass spectrometry with a monolithic column. Separation was achieved using a gradient composition of methanol-0.1% formic acid at a flow rate of 1.0 mL min-1. Mass spectral transitions were recorded in SRM mode. System validation was evaluated for precision, specificity and linearity. Limit of detection for pseudoephedrine, paracetamol, and loratadine were determined to be 3.14, 1.86 and 1.44 ng mL-1, respectively, allowing easy determination in plasma with % recovery of 93.12 to 101.56%.

Influence of initial CaO/SiO2 ratio on the hydration of rice husk ash-Ca(OH)2 and sugar cane bagasse ash-Ca(OH)2 pastes

This work presents the results of a study on the hydration of pastes containing calcium hydroxide and either rice husk ash (RHA) or sugar cane bagasse ash (SCBA) in various initial CaO/SiO2 molar ratios. The products of the reactions were characterized by thermal analyses X-ray diffraction, and scanning electron microscopy. In the case of the RHA pastes, the product was composed of CaO-SiO2-H2O (type I C-S-H) or CaO-SiO2-H2O (type II C-S-H) according to the CaO/SiO2 ratio of the mixture. In contrast, in the case of the SBCA pastes, the product was composed primarily of CaO-SiO2-H2O that differed from both the previous types; the product also contained inclusions of calcium aluminate hydrates.

Adsorption isotherm studies of BOD, TSS and colour reduction from palm oil mill effluent (POME) using boiler fly ash

Palm oil is one of the two most important vegetable oils in the world's oil and fats market. The extraction and purification processes generate different kinds of waste generally known as palm oil mill effluent (POME). Earlier studies had indicated the possibility of using boiler fly ash to adsorb impurities and colour in POME treatment. The adsorption treatment of POME using boiler fly ash was further investigated in detail in this work with regards to the reduction of BOD, colour and TSS from palm oil mill effluent. The amount of BOD, colour and TSS adsorbed increased as the weight of the boiler fly ash used was increased. Also, the smaller particle size of 425µm adsorbed more than the 850µm size. Attempts were made to fit the experimental data with the Freundlich, Langmuir and Dubinin-Radushkevich isotherms. The R² values, which ranged from 0.8974-0.9898, 0.8848-0.9824 and 0.6235-0.9101 for Freundlich, Langmuir and Dubinin-Radushkevich isotherms respectively, showed that Freundlich isotherm gave a better fit followed by Langmuir and then Dubinin-Radushkevich isotherm. The sorption trend could be put as BOD > Colour > TSS. The apparent energy of adsorption was found to be 1.25, 0.58 and 0.97 (KJ/mol) for BOD, colour and TSS respectively, showing that sorption process occurs by physiosorption. Therefore, boiler fly ash is capable of reducing BOD, Colour and TSS from POME and hence could be used to develop a good adsorbent for POME treatment.

The effects of national legislation on the implementation of IFRS in Finland and Russia

This study examines the possible differences in IFRS implementation between Finnish and Russian companies as well as reasons behind them by theoretical means as well as by incorporating a case study of two companies.

Waste Stream Investigation from Perspective of Changing Waste Legislation at Green Sand Foundries

The update of the Finnish legislation concerning waste was unavoidable, to comply with the European Union (EU) requirements defined in the EU-Directive on Waste. The new waste law updates were enacted into the Finnish legislation on the 11.03.2011 and targeted for applicability by the 11.03.2012. This thesis investigates the implications of the new amendments to the waste legislation from the perspective of green sand foundries. The investigations are conducted by comparing two of Componenta’s green sand foundries and evaluating their waste streams. Additionally, the impacts of legislation amendments are critiqued on their environmental and economic aspects. The study’s comparison of waste fractions at the two foundries reveals that sand is dominant in absolute tonnage and costs. The increments of waste taxes forces foundries to focus on waste management, recycling and disposing. The new legislation’s promotion of material efficiency, also guides foundries towards the prevention of waste. A potential preventive measure is to regenerate waste sand resulting to cost savings on both raw-materials and waste management. However, the lack of absolute targets for waste prevention or recycling rates discourages the interests towards creating or adopting new technologies and methods for the waste handling.

Feasibility of ASH DEC‐ process in treating sewage sludge and manure ash in Finland

In Finland the thermal treatment of sewage sludge has been moderate in 21th century. The reason has been the high moisture content of sludge. During 2005-2008, 97-99% of sewage sludge was utilized in landscaping and agriculture. However agricultural use has been during 2005-2007 less than 3 %. The aim of national waste management plan is that by 2016 100% of sludge is used either as soil amendment or energy. The most popular utilization method for manure is spreading it on arable land. The dry manures such as poultry manure and horse manure could also be used in incineration. The ashes could be used as fertilizers and while it is not suitable as a starter fertilizer, it is suitable in maintaining P levels in the soil. One of the main drivers for more efficient nutrient management is the eutrophication in lakes and the Baltic See. ASH DEC process can be used in concentrating phosphorus rich ashes while separating the heavy metals that could be included. ASH DEC process uses thermochemical treatment to produce renewable phosphate for fertilizer production. The process includes mixing of ashes and chlorine donors and subsequent treatment in rotary kiln for 20 min in temperature of 900 – 1 050 oC. The heavy metals evaporate and P-rich product is obtained. The toxic substances are retained in air pollution control system in form of mixed metal hydroxides. The aim of conducting this study is to estimate the potential of ASH DEC process in treating phosphorus rich ashes in Finland. The masses considered in are sewage sludge, dry manure from horses, and poultry and liquid pig manure. To date the usual treatment method for sewage sludge in Finland is composting or anaerobic digestion. Part of the amount of produced sewage sludge (800 kt/a fresh mass and 160 kt/a TS) could also be incinerated and the residual ashes used in ASH DEC process. Incinerating only manure can be economically difficult to manage because the incineration of manure is in Finland considered as waste incineration. Getting a permit for waste incineration is difficult and also small scale waste incineration is too expensive. The manure could act as an additional feedstock in counties with high density of animal husbandry where the land area might not be enough for spreading of manure. Now when the manure acts as a supplementary feedstock beside sludge, the ash can’t be used directly as fertilizer. Then it could be used in ASH DEC process. The perquisite is that the manure producers could pay for the incineration, which might prove problematic.

Fedora Commons as core repository of the EU legislation

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Short-term exposure of mice to cigarette smoke and/or residual oil fly ash produces proximal airspace enlargements and airway epithelium remodeling

Chronic obstructive pulmonary disease (COPD) is associated with inflammatory cell reactions, tissue destruction and lung remodeling. Many signaling pathways for these phenomena are still to be identified. We developed a mouse model of COPD to evaluate some pathophysiological mechanisms acting during the initial stage of the disease. Forty-seven 6- to 8-week-old female C57/BL6 mice (approximately 22 g) were exposed for 2 months to cigarette smoke and/or residual oil fly ash (ROFA), a concentrate of air pollution. We measured lung mechanics, airspace enlargement, airway wall thickness, epithelial cell profile, elastic and collagen fiber deposition, and by immunohistochemistry transforming growth factor-β1 (TGF-β1), macrophage elastase (MMP12), neutrophils and macrophages. We observed regional airspace enlargements near terminal bronchioles associated with the exposure to smoke or ROFA. There were also increases in airway resistance and thickening of airway walls in animals exposed to smoke. In the epithelium, we noted a decrease in the ciliated cell area of animals exposed to smoke and an increase in the total cell area associated with exposure to both smoke and ROFA. There was also an increase in the expression of TGF-β1 both in the airways and parenchyma of animals exposed to smoke. However, we could not detect inflammatory cell recruitment, increases in MMP12 or elastic and collagen fiber deposition. After 2 months of exposure to cigarette smoke and/or ROFA, mice developed regional airspace enlargements and airway epithelium remodeling, although no inflammation or increases in fiber deposition were detected. Some of these phenomena may have been mediated by TGF-β1.

Simulation and material calibration of ultra high strength steel (UHSS) S960 welded joint under static tensile test utilizing finite element method (FEM)

The aim of this work was to calibrate the material properties including strength and strain values for different material zones of ultra-high strength steel (UHSS) welded joints under monotonic static loading. The UHSS is heat sensitive and softens by heat due to welding, the affected zone is heat affected zone (HAZ). In this regard, cylindrical specimens were cut out from welded joints of Strenx® 960 MC and Strenx® Tube 960 MH, were examined by tensile test. The hardness values of specimens’ cross section were measured. Using correlations between hardness and strength, initial material properties were obtained. The same size specimen with different zones of material same as real specimen were created and defined in finite element method (FEM) software with commercial brand Abaqus 6.14-1. The loading and boundary conditions were defined considering tensile test values. Using initial material properties made of hardness-strength correlations (true stress-strain values) as Abaqus main input, FEM is utilized to simulate the tensile test process. By comparing FEM Abaqus results with measured results of tensile test, initial material properties will be revised and reused as software input to be fully calibrated in such a way that FEM results and tensile test results deviate minimum. Two type of different S960 were used including 960 MC plates, and structural hollow section 960 MH X-joint. The joint is welded by BöhlerTM X96 filler material. In welded joints, typically the following zones appear: Weld (WEL), Heat affected zone (HAZ) coarse grained (HCG) and fine grained (HFG), annealed zone, and base material (BaM). Results showed that: The HAZ zone is softened due to heat input while welding. For all the specimens, the softened zone’s strength is decreased and makes it a weakest zone where fracture happens while loading. Stress concentration of a notched specimen can represent the properties of notched zone. The load-displacement diagram from FEM modeling matches with the experiments by the calibrated material properties by compromising two correlations of hardness and strength.

Real-time monitoring of laser scribing process utilizing high-speed camera

Currently, laser scribing is growing material processing method in the industry. Benefits of laser scribing technology are studied for example for improving an efficiency of solar cells. Due high-quality requirement of the fast scribing process, it is important to monitor the process in real time for detecting possible defects during the process. However, there is a lack of studies of laser scribing real time monitoring. Commonly used monitoring methods developed for other laser processes such a laser welding, are sufficient slow and existed applications cannot be implemented in fast laser scribing monitoring. The aim of this thesis is to find a method for laser scribing monitoring with a high-speed camera and evaluate reliability and performance of the developed monitoring system with experiments. The laser used in experiments is an IPG ytterbium pulsed fiber laser with 20 W maximum average power and Scan head optics used in the laser is Scanlab’s Hurryscan 14 II with an f100 tele-centric lens. The camera was connected to laser scanner using camera adapter to follow the laser process. A powerful fully programmable industrial computer was chosen for executing image processing and analysis. Algorithms for defect analysis, which are based on particle analysis, were developed using LabVIEW system design software. The performance of the algorithms was analyzed by analyzing a non-moving image from the scribing line with resolution 960x20 pixel. As a result, the maximum analysis speed was 560 frames per second. Reliability of the algorithm was evaluated by imaging scribing path with a variable number of defects 2000 mm/s when the laser was turned off and image analysis speed was 430 frames per second. The experiment was successful and as a result, the algorithms detected all defects from the scribing path. The final monitoring experiment was performed during a laser process. However, it was challenging to get active laser illumination work with the laser scanner due physical dimensions of the laser lens and the scanner. For reliable error detection, the illumination system is needed to be replaced.

An impact evaluation of the Ontario ban on smoking in schools and on school property : does the ban on smoking influence high school students' intentions to smoke cigarettes?

The Ontario Tobacco Control Act of 1994 imposed a total ban on smoking in schools, and on school property for every school in the province. The imposition of this policy created problems for school administrators. For instance, students who were smoking on walkways and properties adjacent to school boundaries, clashed with neighbouring property owners who were angry about the resulting damage and disruption. The enforcement of this policy consumes valuable resources at each school; therefore, knowledge about the impact of the policy is important. If effective, this policy has the potential to improve the health of students over their lifetime, by preventing or delaying smoking behaviour. Alternatively, an ineffective policy will continue to create administrative problems for the school and serve no legitimate purpose. Therefore, knowledge about the impact of the smoking ban policy on students' smoking intentions assists policy makers and school administrators in their understanding of the policy's impact within the schools. This research provided an impact evaluation of the ban on smoking in schools and on school property in Ontario. A total of 2069 students, from five high schools, in the Niagara Region, provided complete responses to a survey, designed to test whether smoking intentions were affected by the imposition of the policy. The study used Ajzen's theory of planned behaviour (Ajzen, 1991), specifically, the perceived behavioural control measure, to gain some understanding of students' perceptions of control over smoking imposed by the ban. The findings indicate the policy has the potential to influence students' overall smoking intentions. The ban on smoking policy was found to be a significant predictor of the smoking intentions of high school students. As well, attitude, social norms, and perceptions of control were significant predictors of smoking intentions. Exploratory findings also indicated differences between the control beliefs of students from different high schools, indicating potential differences in the enforcement of the smoking ban between schools. The findings also support the utility of the theory of planned behaviour as a methodology for evaluating the influence of punitive policies. This research study should be continued by utilizing the full theory of planned behaviour, including two phases of data collection and the measurement of actual smoking behaviour.

Forsaking all others: towards a new model of nationalism utilizing the case study of former Yugoslavia

Many people would like to believe that nationalism is a thing of the past, a dinosaur belonging to some bygone, uncivilized era. Such a belief is not borne out by recent history, however. Nationalism occupies the political forum with as much force as ever. Yet, in many ways, it remains a mystery to us. The purpose of this study is to explore individual motivations involved in the rise of nationalism, in addition to the role of structural factors. The linkage employed in this exploration is the psychosocial phenomenon of self-identity, including emotions and self-esteem. We demonstrate how individual, socially-constructed self-identity accounts for why some people embrace nationalism while others eschew it. The methodology employed was theoretical and historical analyses of secondary sources and indepth interviews with subjects who had some connection with former Yugoslavia, the country utilized to test the new model. Our analyses yielded the result that current conceptualizations of nationalism from an exclusively macro or micro perspective are unsatisfactory; we require a more comprehensive approach wherein the two perspectives are integrated. Such an integration necessitates a bridge: hence, our new model, which rests on the psychosocial premise, offers a more useful conceptual tool for the understanding of nationalism. We conclude that nationalism is first and foremost a matter relating to individual social self-identity which takes place within a particular context where oppositional forces emerge from structural factors and our membership in a particular group becomes paramount.

Utilizing a Phenomenological Approach to Examine the Experience of Sexuality for Women Concerned about Urinary Incontinence following Spinal Cord Injury

Sexuality after spinal cord injury (SCI) is a complex issue that is influenced by a number of social, psychological and physiological factors, one of which is urinary incontinence (UI). Using a phenomenological approach, seven mixed methods interviews combining both the interview guide and standardized open-ended approaches were conducted to examine the experience of sexuality for women who are concerned about UI following SCI. Sexual function was one of the top priorities for the women after SCI, and UI was one of the main concerns the women had regarding sexuality. The findings of this study demonstrate that various dimensions of intimacy and the sexual experience as a whole were affected by UI, and the women discussed both physical and psychological concerns. The main issues regarding sexuality included concerns related to relationships, frustrations with limited sexual activities and the difficulty of being sexually satisfied, the number of unanswered questions and concerns, and a fear of being hurt or injured while participating in sexual activities. The main concerns regarding UI were embarrassment, the work and inconvenience involved with the clean-up of UI, bladder infections, the lack of accessible washrooms, and the negative effects of UI medications. When examining sexuality and UI together, the major issues were the constant comparison to the way things were before SCI, as well as the new concerns that the women did not have to worry about previously, worrying about how their partner would react if UI were to occur during sexual activity, and the impact of their own feelings toward UI on sexuality, a connection between pleasurable sexual sensations and UI as well as difficulty differentiating between the sensation of UI with the sensation of UI, dealing with infected urine during sexual activity, having to discuss UI with a new potential sexual partner, and a fear of rejection. Other identified issues included those related to body image, a lack of resources, Doctors who were inadequately educated regarding SCI, and issues related to both having and raising children. There is a significant shortage of information available for women with SCI to use as a resource regarding sexual function in general, and sexual function as it relates to UI. It is necessary that future work focus on creating resources to assist in this area, and that the dissemination of those resources becomes both appropriate and effective. Addressing sexual function and UI which are among the top concerns for this population has the opportunity to greatly improve quality of life (QOL) for these individuals.