Powder forging of a sintered Al-3.8Cu-1Mg-0.8Si-O.1Sn alloy

The forging characteristics of an Al-Cu-Mg-Si-Sn alloy are examined using it new testing strategy which incorporates a double truncated cone specimen and finite element modelling. This sample geometry produces controlled strain distributions within a single specimen and can readily identify the specific strain required to achieve a specific microstructural event by matching the metallographic data with the strain profiles calculated from finite element software, The friction conditions were determined using the conventional friction ring test, which was evaluated using finite element software. The rheological properties of the alloy, evaluated from compression testing of right cylinders, are similar to the properties of conventional aluminium forgings. A hoop strain develops at the outer diameter of the truncated cones and this leads to pore opening at the outer few millimetres. The porosity is effectively removed when the total strain equals the net compressive strain. The strain profiles that develop in the truncated cones are largely independent of the processing temperature and the strain rate although the strain required for pore closure increases as the forging temperature is reduced. This suggests that the microstructure and the strain rate sensitivity may also be important factors controlling pore behaviour. (C) 2002 Elsevier Science B.V. All rights reserved.

Conformational changes in monolayers of a cationic amphiphilic porphyrin on saline subphases

Langmuir monolayer films of the tetracationic porphyrin tetrakis(octadecyl-4-pyridin ium)porphyrinatozinc(II) bromide on various salt containing subphases were analyzed using surface pressure-area isotherms and X-ray reflectivity. The use of these complementary techniques showed that the porphyrin molecules undergo changes in conformation upon compression. Two main phases were identified, one in which the porphyrin moiety is parallel to the subphase and one in which the porphyrin moiety is tilted out of the plane. The addition of different salts into the subphase brought about changes in film behaviour, which are explained in terms of a lyotropic series. Copyright (C) 2002 Society of Porphyrins,& Phthalocyanines.

D2 dopamine receptor gene polymorphism discriminates two kinds of novelty seeking

Cloninger's psychobiological model of personality as applied to substance misuse has received mixed support. Contrary to the model, recent data suggest that a combination of high novelty seeking (NS) and high harm avoidance (HA) represents a significant risk for the development of severe substance misuse. A genetic polymorphism previously implicated in severe substance dependence, the A1 allele of the D2 dopamine receptor (DRD2) gene, was examined in relation to NS and HA amongst 203 adolescent boys. Specifically, we hypothesized that subjects with the A1 + allele (A1/A1 and A1/A2 genotypes) would report stronger NS and would exhibit a more positive relationship between NS and HA than those with the A1-allele (A2/A2 genotypes). These predictions were supported. The correlation between NS and HA in 81 A1 + allelic boys (r = 0.27, P = 0.02), and that in the 122 A1- allelic boys (r = -0.15, P = 0.09), indicated that this relationship differed according to allelic status (F = 8.52, P < 0:004). Among those with the A1-allele, the present results are consistent with the traditional view that novelty seeking provides positive reinforcement, or the fulfillment of appetitive drives. In contrast, novelty seeking in those with the A1 + allele appears to include a negative reinforcement or self-medicating function. (C) 2002 Elsevier Science Ltd. All rights reserved.

Stress correlation function evolution in lattice solid elasto-dynamic models of shear and fracture zones and earthquake prediction

It has been argued that power-law time-to-failure fits for cumulative Benioff strain and an evolution in size-frequency statistics in the lead-up to large earthquakes are evidence that the crust behaves as a Critical Point (CP) system. If so, intermediate-term earthquake prediction is possible. However, this hypothesis has not been proven. If the crust does behave as a CP system, stress correlation lengths should grow in the lead-up to large events through the action of small to moderate ruptures and drop sharply once a large event occurs. However this evolution in stress correlation lengths cannot be observed directly. Here we show, using the lattice solid model to describe discontinuous elasto-dynamic systems subjected to shear and compression, that it is for possible correlation lengths to exhibit CP-type evolution. In the case of a granular system subjected to shear, this evolution occurs in the lead-up to the largest event and is accompanied by an increasing rate of moderate-sized events and power-law acceleration of Benioff strain release. In the case of an intact sample system subjected to compression, the evolution occurs only after a mature fracture system has developed. The results support the existence of a physical mechanism for intermediate-term earthquake forecasting and suggest this mechanism is fault-system dependent. This offers an explanation of why accelerating Benioff strain release is not observed prior to all large earthquakes. The results prove the existence of an underlying evolution in discontinuous elasto-dynamic, systems which is capable of providing a basis for forecasting catastrophic failure and earthquakes.

Simulation of the load-unload response ratio and critical sensitivity in the lattice solid model

The Load-Unload Response Ratio (LURR) method is an intermediate-term earthquake prediction approach that has shown considerable promise. It involves calculating the ratio of a specified energy release measure during loading and unloading where loading and unloading periods are determined from the earth tide induced perturbations in the Coulomb Failure Stress on optimally oriented faults. In the lead-up to large earthquakes, high LURR values are frequently observed a few months or years prior to the event. These signals may have a similar origin to the observed accelerating seismic moment release (AMR) prior to many large earthquakes or may be due to critical sensitivity of the crust when a large earthquake is imminent. As a first step towards studying the underlying physical mechanism for the LURR observations, numerical studies are conducted using the particle based lattice solid model (LSM) to determine whether LURR observations can be reproduced. The model is initialized as a heterogeneous 2-D block made up of random-sized particles bonded by elastic-brittle links. The system is subjected to uniaxial compression from rigid driving plates on the upper and lower edges of the model. Experiments are conducted using both strain and stress control to load the plates. A sinusoidal stress perturbation is added to the gradual compressional loading to simulate loading and unloading cycles and LURR is calculated. The results reproduce signals similar to those observed in earthquake prediction practice with a high LURR value followed by a sudden drop prior to macroscopic failure of the sample. The results suggest that LURR provides a good predictor for catastrophic failure in elastic-brittle systems and motivate further research to study the underlying physical mechanisms and statistical properties of high LURR values. The results provide encouragement for earthquake prediction research and the use of advanced simulation models to probe the physics of earthquakes.

Simulation of the micro-physics of rocks using LSMearth

The particle-based Lattice Solid Model (LSM) was developed to provide a basis to study the physics of rocks and the nonlinear dynamics of earthquakes (MORA and PLACE, 1994; PLACE and MORA, 1999). A new modular and flexible LSM approach has been developed that allows different microphysics to be easily included in or removed from the model. The approach provides a virtual laboratory where numerical experiments can easily be set up and all measurable quantities visualised. The proposed approach provides a means to simulate complex phenomena such as fracturing or localisation processes, and enables the effect of different micro-physics on macroscopic behaviour to be studied. The initial 2-D model is extended to allow three-dimensional simulations to be performed and particles of different sizes to be specified. Numerical bi-axial compression experiments under different confining pressure are used to calibrate the model. By tuning the different microscopic parameters (such as coefficient of friction, microscopic strength and distribution of grain sizes), the macroscopic strength of the material and can be adjusted to be in agreement with laboratory experiments, and the orientation of fractures is consistent with the theoretical value predicted based on Mohr-Coulomb diagram. Simulations indicate that 3-D numerical models have different macroscopic properties than in 2-D and, hence, the model must be recalibrated for 3-D simulations. These numerical experiments illustrate that the new approach is capable of simulating typical rock fracture behaviour. The new model provides a basis to investigate nucleation, rupture and slip pulse propagation in complex fault zones without the previous model limitations of a regular low-level surface geometry and being restricted to two-dimensions.

Genetic constraints on the evolution of mate recognition under natural selection

Field populations of Drosophila serrata display reproductive character displacement in cuticular hydrocarbons (CHCs) when sympatric with Drosophila birchii. We have previously shown that the naturally occurring pattern of reproductive character displacement can be experimentally replicated by exposing field allopatric populations of D. serrata to experimental sympatry with D. birchii. Here, we tested whether the repeated evolution of reproductive character displacement in natural and experimental populations was a consequence of genetic constraints on the evolution of CHCs. The genetic variance-covariance (G) matrices for CHCs were determined for populations of D. serrata that had evolved in either the presence or absence of D. birchii under field and experimental conditions. Natural selection on mate recognition under both field and experimental sympatric conditions increased the genetic variance in CHCs consistent with a response to selection based on rare alleles. A close association between G eigenstructure and the eigenstructure of the phenotypic divergence (D) matrix in natural and experimental populations suggested that G matrix eigenstructure may have determined the direction in which reproductive character displacement evolved during the reinforcement of mate recognition.

Hemodynamic and ventilatory effects of manual respiratory physiotherapy techniques of chest clapping, vibration, and shaking in an animal model

Chest clapping, vibration, and shaking were studied in 10 physiotherapists who applied these techniques on an anesthetized animal model. Hemodynamic variables (such as heart rate, blood pressure, pulmonary artery pressure, and right atrial pressure) were measured during the application of these techniques to verify claims of adverse events. In addition, expired tidal volume and peak expiratory flow rate were measured to ascertain effects of these techniques. Physiotherapists in this study applied chest clapping at a rate of 6.2 +/- 0.9 Hz, vibration at 10.5 +/- 2.3 Hz, and shaking at 6.2 +/- 2.3 Hz. With the use of these rates, esophageal pressure swings of 8.8 +/- 5.0, 0.7 +/- 0.3, and 1.4 +/- 0.7 mmHg resulted from clapping, vibration, and shaking respectively. Variability in rates and forces generated by these techniques was 80% of variance in shaking force (P = 0.003). Application of these techniques by physiotherapists was found to have no significant effects on hemodynamic and most ventilatory variables in this study. From this study, we conclude that chest clapping, vibration, and shaking 1) can be consistently performed by physiotherapists; 2) are significantly related to physiotherapists' characteristics, particularly clinical experience; and 3) caused no significant hemodynamic effects.

Heat transfer and flow behind a step in high enthalpy superorbital flow

Heat transfer levels have been investigated behind a rearward-facing step in a superorbital expansion tube. The heat transfer was measured along a flat plate and behind 2 and 3mm steps with the same length to step height ratio. Results were obtained with air as the test gas at speeds of 6.76kms(-1) and 9-60kms(-1) corresponding to stagnation enthalpies of 26MJ/kg and 48MJ/kg respectively. A laminar boundary layer was established on the flat plate and measured heat transfer levels were consistent with classical empirical correlations. In the case of flow behind a step, the measurements showed a gradual rise in heat transfer from the rear of the step to a plateau several step heights downstream for both flow conditions. Reattachment distance was estimated to be approximately 1.6 step heights downstream of the 2mm step at the low enthalpy condition through the use of flow visualisation.

Large amplitude vibration of thermo-electro-mechanically stressed FGM laminated plates

This paper presents a large amplitude vibration analysis of pre-stressed functionally graded material (FGM) laminated plates that are composed of a shear deformable functionally graded layer and two surface-mounted piezoelectric actuator layers. Nonlinear governing equations of motion are derived within the context of Reddy's higher-order shear deformation plate theory to account for transverse shear strain and rotary inertia. Due to the bending and stretching coupling effect, a nonlinear static problem is solved first to determine the initial stress state and pre-vibration deformations of the plate that is subjected to uniform temperature change, in-plane forces and applied actuator voltage. By adding an incremental dynamic state to the pre-vibration state, the differential equations that govern the nonlinear vibration behavior of pre-stressed FGM laminated plates are derived. A semi-analytical method that is based on one-dimensional differential quadrature and Galerkin technique is proposed to predict the large amplitude vibration behavior of the laminated rectangular plates with two opposite clamped edges. Linear vibration frequencies and nonlinear normalized frequencies are presented in both tabular and graphical forms, showing that the normalized frequency of the FGM laminated plate is very sensitive to vibration amplitude, out-of-plane boundary support, temperature change, in-plane compression and the side-to-thickness ratio. The CSCF and CFCF plates even change the inherent hard-spring characteristic to soft-spring behavior at large vibration amplitudes. (C) 2003 Elsevier B.V. All rights reserved.

Physical activity and sedentary behavior: A population-based study of barriers, enjoyment, and preference

The associations of physical activity and sedentary behavior with barriers, enjoyment, and preferences were examined in a population-based mail survey of 1,332 adults. Respondents reporting high enjoyment and preference for physical activity were more likely to report high levels of activity. Those reporting cost, the weather, and personal barriers to physical activity were less likely to be physically active. Preference for sedentary behavior was associated with the decreased likelihood of being physically active, and the weather as a barrier to physical activity was associated with the increased likelihood of sedentary behavior. These constructs can be used to examine individual and environmental influences on physical activity and sedentary behavior in specific populations and could inform the development of targeted interventions.

Federalismo e rela????es intergovernamentais: os cons??rcios p??blicos como instrumento de coopera????o federativa

Se nos estados federais os mecanismos de coopera????o e coordena????o intergovernamental j?? s??o relevantes, no caso brasileiro eles ganham centralidade ainda maior. A Constitui????o Federal de 1988 agregou complexidade ao desenho federativo brasileiro, reconhecendo o munic??pio como ente federado. Esse processo foi acompanhado por intensa descentraliza????o de pol??ticas p??blicas, pelo fortalecimento do poder local e por mecanismos pouco coordenados de rela????o vertical e horizontal entre os entes federativos. Ao mesmo tempo, a aus??ncia de pol??ticas de desenvolvimento regional acentuou as desigualdades locais e regionais observadas historicamente no pa??s. Diferentes experi??ncias de consorciamento foram levadas a cabo por munic??pios no pa??s e ainda hoje esse ?? um instrumento de larga utiliza????o. De forma diversa, as iniciativas de coopera????o entre estados s??o ainda incipientes. As limita????es institucionais e jur??dicas dos desenhos utilizados pelos munic??pios, no entanto, levaram ?? aprova????o da Emenda Constitucional n?? 19/98, que instituiu os cons??rcios p??blicos e a gest??o associada de servi??os p??blicos.

Estudo da resistência não drenada de solo de baixa consistência por meio de ensaios de campo e laboratório

A variabilidade natural dos solos torna complexo o conhecimento de suas propriedades na elaboração de projetos geotécnicos, sendo a determinação da resistência ao cisalhamento não drenada um parâmetro importante nas análises de estabilidade de solos moles. Os ensaios de laboratório de cone e palheta, não convencionais, os ensaios de campo de palheta e piezocone e os ensaios de compressão simples e triaxial não adensado e não drenado foram utilizados para mensurar a resistência não drenada de uma camada de argila marinha mole localizada na planície costeira central brasileira. Os ensaios de laboratório foram realizados em amostras indeformadas coletadas com amostradores de pistão estacionário em vertical próxima à realização dos ensaios de campo. O sítio foi investigado preliminarmente por sondagens de simples reconhecimento, sendo apresentado o perfil estratigráfico por meio de modelagem computacional. Foram também realizados ensaios para caracterização física (análise granulométrica, teor de umidade, limites de liquidez e plasticidade, densidade real dos grãos) e mineralógica (difração de raios X), e ensaios de adensamento para obtenção do histórico de tensões e classificação de qualidade das amostras indeformadas. Os valores de resistência não drenada obtidos pelos ensaios de laboratório foram comparados ao perfil contínuo de resistência determinado empiricamente pelo ensaio de piezocone, com fator de cone Nkt calibrado pelo ensaio de palheta de campo, apresentando boa concordância, com a variabilidade natural do solo influenciando de forma preponderante a qualidade das amostras na variação entre os resultados. Os valores de resistência obtidos pelos ensaios de laboratório de cone e palheta foram comparados entre si, apresentando boa compatibilidade. Ambos, quando comparados ao ensaio de palheta de campo, não apresentaram boa concordância. Os resultados de resistência obtidos pelos ensaios de compressão simples e triaxial apresentaram boa compatibilidade com os resultados do ensaio de laboratório de cone, o que não ocorreu com os resultados do ensaio de laboratório de palheta. Na comparação entre a resistência normalizada pela tensão de sobreadensamento obtida pelos diversos métodos e algumas correlações empíricas da literatura internacional, foi observado para as amostras de solo com índice de plasticidade superior a 60% boa concordância com as correlações de Mesri (1975) e Jamiolkowski et al (1985). Os ensaios não convencionais apresentaram boa confiabilidade, que aliado a simplicidade e agilidade de execução, justificam a difusão destes na prática da investigação geotécnica brasileira como método alternativo para complementar e dar suporte às estimativas de resistência não drenada de solos moles.

Estudo do efeito da face sobre o equilíbrio de estruturas de contenção de solo reforçado sob condições de trabalho

Os métodos de análise de estruturas de contenção de solo reforçado sob condições de trabalho, em geral, desconsideram a contribuição da face para o equilíbrio da estrutura. Visando estudar a influência do peso específico da face e das propriedades relacionadas à rigidez da mesma sobre o desempenho das estruturas de solo reforçado, são realizadas simulações numéricas de diversas estruturas, utilizando a versão de dupla precisão do programa CRISP92-SC. Avalia-se, também, o emprego de diferentes tipos de elementos para a representação da face. Verifica-se que a face rígida impõe redução significativa das solicitações máximas de tração nos reforços e dos deslocamentos das estruturas de solo reforçado. A influência do peso específico da face sobre a estabilidade interna dos maciços reforçados mostrase desprezível e constata-se que a rigidez à flexão e a rigidez axial da face, função da sua geometria e do seu módulo de Young, são parâmetros influentes no comportamento das estruturas de contenção de solo reforçado. As variações da tração no reforço e da resultante de força cortante na face, em decorrência do enrijecimento da face, são analisadas e propõe-se uma relação entre elas. Quanto à forma de representação de uma face com rigidez expressiva, na simulação de uma estrutura de solo reforçado com o CRISP92-SC, é observado que a representação da face, seja por elementos de viga, seja por elementos quadriláteros, não altera os resultados da análise.

A negação no português falado em Vitória/ES

Todas as línguas possuem algum recurso para expressar a negação verbal, porém cada uma apresenta estratégias próprias para sua realização. No português brasileiro (PB), há três estratégias de negação: 1) pré-verbal (Não+SV); 2) dupla negação (Não+SV+Não) e 3) pós-verbal (SV+Não). À luz da Sociolinguística Variacionista e com base na amostra PortVix (Português Falado na Cidade de Vitória), que tem por parâmetros sociais o gênero/sexo do falante, sua faixa etária e seu nível de escolaridade, o presente trabalho analisa a variação no uso das estruturas de negação no português falado na cidade de Vitória/ES, a fim de situar, a partir desse fenômeno, a variedade capixaba no cenário do PB. Também toma por base a proposta de Schwenter (2005) de que as três variantes se alternam apenas quando o conteúdo negado é ativado no discurso. Sendo assim, se a proposição negada apresentar um estatuto de uma informação nova, apenas a negação pré-verbal pode ser empregada. Desse modo, em nossa pesquisa, buscamos entender quais fatores influenciam a alternância das formas de negação e verificar os contextos linguístico-discursivos que comportam essa variação. Ao confrontarmos nossos resultados com os de outras pesquisas, observamos que a dupla negação é bastante produtiva na fala capixaba, representando 21,1% de um total de 2263 dados. Ao realizarmos rodadas em que foram amalgamadas duas variantes e contrapostas a uma outra, foram selecionados pelo programa Goldvarb X (SANKOFF; TAGLIAMONTE; SMITH, 2005) e, portanto, considerados estatisticamente relevantes para a dupla negação, os seguintes fatores: as sequências dialogais, a ausência de reforço negativo, a ausência de marcadores conversacionais e as orações absolutas. Para a negação pós-verbal, foram selecionadas as seguintes variáveis: as proposições negadas diretamente ativadas e as sequências dialogais. Para a negação pré-verbal, os fatores estatisticamente relevantes foram: as sequências narrativas e as argumentativas, a presença de reforço negativo, a presença de marcadores conversacionais, as orações principais e o gênero masculino. Os resultados revelaram que a variação no uso das estruturas negativas é um fenômeno marcadamente discursivo, mas também com atuação de alguns fatores sintáticos.