Time dependence of effective slip on textured hydrophobic surfaces

In this paper, we present results on water flow past randomly textured hydrophobic surfaces with relatively large surface features of the order of 50 µm. Direct shear stress measurements are made on these surfaces in a channel configuration. The measurements indicate that the flow rates required to maintain a shear stress value vary substantially with water immersion time. At small times after filling the channel with water, the flow rates are up to 30% higher compared with the reference hydrophilic surface. With time, the flow rate gradually decreases and in a few hours reaches a value that is nearly the same as the hydrophilic case. Calculations of the effective slip lengths indicate that it varies from about 50 µm at small times to nearly zero or “no slip” after a few hours. Large effective slip lengths on such hydrophobic surfaces are known to be caused by trapped air pockets in the crevices of the surface. In order to understand the time dependent effective slip length, direct visualization of trapped air pockets is made in stationary water using the principle of total internal reflection of light at the water-air interface of the air pockets. These visualizations indicate that the number of bright spots corresponding to the air pockets decreases with time. This type of gradual disappearance of the trapped air pockets is possibly the reason for the decrease in effective slip length with time in the flow experiments. From the practical point of usage of such surfaces to reduce pressure drop, say, in microchannels, this time scale of the order of 1 h for the reduction in slip length would be very crucial. It would ultimately decide the time over which the surface can usefully provide pressure drop reductions. ©2009 American Institute of Physics

A sequential analysis of "nú" and "núna" in Icelandic conversation

This thesis is an empirical study of how two words in Icelandic, "nú" and "núna", are used in contemporary Icelandic conversation. My aims in this study are, first, to explain the differences between the temporal functions of "nú" and "núna", and, second, to describe the non-temporal functions of "nú". In the analysis, a focus is placed on comparing the sequential placement of the two words, on their syntactical distribution, and on their prosodic realization. The empirical data comprise 14 hours and 11 minutes of naturally occurring conversation recorded between 1996 and 2003. The selected conversations represent a wide range of interactional contexts including informal dinner parties, institutional and non-institutional telephone conversations, radio programs for teenagers, phone-in programs, and, finally, a political debate on television. The theoretical and methodological framework is interactional linguistics, which can be described as linguistically oriented conversation analysis (CA). A comparison of "nú" and "núna" shows that the two words have different syntactic distributions. "Nú" has a clear tendency to occur in the front field, before the finite verb, while "núna" typically occurs in the end field, after the object. It is argued that this syntactic difference reflects a functional difference between "nú" and "núna". A sequential analysis of "núna" shows that the word refers to an unspecified period of time which includes the utterance time as well as some time in the past and in the future. This temporal relation is referred to as reference time. "Nú", by contrast, is mainly used in three different environments: a) in temporal comparisons, 2) in transitions, and 3) when the speaker is taking an affective stance. The non-temporal functions of "nú" are divided into three categories: a) "nú" as a tone particle, 2) "nú" as an utterance particle, and 3) "nú" as a dialogue particle. "Nú" as a tone particle is syntactically integrated and can occur in two syntactic positions: pre-verbally and post-verbally. I argue that these instances are employed in utterances in which a speaker is foregrounding information or marking it as particularly important. The study shows that, although these instances are typically prosodically non-prominent and unstressed, they are in some cases delivered with stress and with a higher pitch than the surrounding talk. "Nú" as an utterance particle occurs turn-initially and is syntactically non-integrated. By using "nú", speakers show continuity between turns and link new turns to prior ones. These instances initiate either continuations by the same speaker or new turns after speaker shifts. "Nú" as a dialogue particle occurs as a turn of its own. The study shows that these instances register informings in prior turns as unexpected or as a departure from the normal state of affairs. "Nú" as a dialogue particle is often delivered with a prolonged vowel and a recognizable intonation contour. A comparative sequential and prosodic analysis shows that in these cases there is a correlation between the function of "nú" and the intonation contour by which it is delivered. Finally, I argue that despite the many functions of "nú", all the instances can be said to have a common denominator, which is to display attention towards the present moment and the utterances which are produced prior or after the production of "nú". Instead of anchoring the utterances in external time or reference time, these instances position the utterance in discourse internal time, or discourse time.

Nonverbal predication in Erzya : Studies on morphosyntactic variation and part of speech distinctions

This dissertation consists of four articles and an introduction. The five parts address the same topic, nonverbal predication in Erzya, from different perspectives. The work is at the same time linguistic typology and Uralic studies. The findings based on a large corpus of empirical Erzya data, which was collected using several different methods and included recordings of the spoken language, made it possible for the present study to apply, then test and finally discuss the previous theories based on cross-linguistic data. Erzya makes use of multiple predication patterns which vary from totally analytic to the morphologically very complex. Nonverbal predicate clause types are classified on the basis of propositional acts in clauses denoting class-membership, identity, property and location. The predicates of these clauses are nouns, adjectives and locational expressions, respectively. The following three predication strategies in Erzya nonverbal predication can be identified: i. the zero-copula construction, ii. the predicative suffix construction and iii. the copula construction. It has been suggested that verbs and nouns cannot be clearly distinguished on morphological grounds when functioning as predicates in Erzya. This study shows that even though predicativity must not be considered a sufficient tool for defining parts of speech in any language, the Erzya lexical classes of adjective, noun and verb can be distinguished from each other also in predicate position. The relative frequency and degree of obligation for using the predicative suffix construction decreases when moving left to right on the scale verb adjective/locative noun ( identificational statement). The predicative suffix is the main pattern in the present tense over the whole domain of nonverbal predication in Standard Erzya, but if it is replaced it is most likely to be with a zero-copula construction in a nominal predication. This study exploits the theory of (a)symmetry for the first time in order to describe verbal vs. nonverbal predication. It is shown that the asymmetry of paradigms and constructions differentiates the lexical classes. Asymmetrical structures are motivated by functional level asymmetry. Variation in predication as such adds to the complexity of the grammar. When symmetric structures are employed, the functional complexity of grammar decreases, even though morphological complexity increases. The genre affects the employment of predication strategies in Erzya. There are differences in the relative frequency of the patterns, and some patterns are totally lacking from some of the data. The clearest difference is that the past tense predicative suffix construction occurs relatively frequently in Standard Erzya, while it occurs infrequently in the other data. Also, the predicative suffixes of the present tense are used more regularly in written Standard Erzya than in any other genre. The genre also affects the incidence of the translative in uľ(ń)ems copula constructions. In translations from Russian to Erzya the translative case is employed relatively frequently in comparison to other data. This study reveals differences between the two Mordvinic languages Erzya and Moksha. The predicative suffixes (bound person markers) of the present tense are used more regularly in Moksha in all kinds of nonverbal predicate clauses compared to Erzya. It should further be observed that identificational statements are encoded with a predicative suffix in Moksha, but seldom in Erzya. Erzya clauses are more frequently encoded using zero-constructions, displaying agreement in number only.

The performance of strawberry plugs in Queensland

Plugs or containerized plants can offer several advantages over traditional bare-rooted runner plants for strawberry (Fragaria x ananassa) production. Some of these benefits include easier planting, better establishment, fewer pests and diseases, and lower water use during plant establishment resulting in less leaching of applied fertilizers. Plugs also offer the potential for mechanical planting. In some areas of Europe and North America, plugs provide earlier production, greater productivity and larger fruit than runners. Research has also shown that the plants can be grown under short days and low temperatures to manipulate flower initiation and fruiting. Plugs are more expensive to buy compared with runner plants, and will only be adopted by industry if the extra costs are matched by convenience, resource conservation, increased fruiting and returns to producers. We investigated the productivity of 'Festival' and 'Sugarbaby' propagated as plugs (75 cm3 containers) and runners from Stanthorpe in southern Queensland (elevation of 872 m), and grown at Nambour on the Sunshine Coast (elevation 29 m). At planting, the plug plants weighed 0.8 ± 0.1 g DW compared with 53 ± 0.5 g DW for the runner plants. 'Sugarbaby' plugs were larger than 'Festival' plugs (33 ± 0.6 g versus 2.9 ± 0.6 g). The differences in growth at planting were maintained until the third week of July (day 94), with the plug plants weighing 17.8 ± 2.2 g, and the runner plants 21.4 ± 23 g. The proportion of plant dry matter allocated to the leaves increased over time from 59 to 70%, while the proportion allocated to the roots decreased from 21 to 10%. Harvest commenced after 60 days, with the plug plants yielding only 60% of the yields of the runner plants up until 8 August or day 109 (14.2 ± 1.4 g plant -1 week-1 versus 23.6 ± 1.9 g plant-1 week-1). 'Festival' (22.2 ± 2.0 g plant-1 week -1) had higher yields than 'Sugarbaby' (15.5 ± 1.5 g plant-1 week-1), even though plants of the latter were larger. Average fruit weight was 15.6 ± 0.3 g, with no effect of cultivar, plant type or harvest time. In other words, the differences in yield between the various treatments were due to differences in fruit set The lower yields of the plug plants probably reflect their small size at planting. Future research should determine whether plugs grown in larger cells (150 to 300 cm3 as in the USA and Europe) are more productive. Tips to be grown in larger containers should be harvested earlier than those for small cells to maximize root growth of the plug plant. This will probably extend the time required from harvest of the tips and potting them from the current four to five weeks, to eight to ten weeks.

Kinetics of Extraction of Iron(II1) by Bis(2-ethylhexyl Phosphate in a Laminar Liquid-Liquid Jet Reactor

The kinetics of iron(II1) extraction by bis(Zethylhexy1) phosphate (HDEHP, HA) in kerosene from sulfuric acid solutions has been studied in a liquid-liquid laminar jet reactor. The contact time of the interface in this reacting device is of the same order of magnitude as the surface renewal time in dispersion mixing and much less than that obtained in the relatively quiescent condition of the Lewis cell. Yet the analysis of the data in this study suggested a rate-controlling step involving surface saturation quite in conformity with that obtained in the Lewis cell and not with that in dispersion mixing as reported in the literature. Further, the mechanism suggested a weaker dependence of the rate on hydrogen ion concentration which was reported by other workers.

Powdery mildew on Passiflora in Australia

Oidiopsis sp., the anamorph of Leveillula taurica (Erysiphaceae), is reported for the first time in Australia on Passiflora edulis, and Oidium passiflorae on Passiflora foetida. A detailed description and illustration of the specimens are given.

Podosphaera xanthii on Euryops chrysanthemoides in Australia

The anamorph of Podosphaera xanthii (Erysiphaceae) on Euryops chrysanthemoides is reported for the first time in Australia. A detailed description of the specimen is given, along with its rDNA internal transcribed spacer sequence.

Embedding sustainability in a real-world context: Developing a world class early learning centre

This symposium describes what is possible when early childhood professionals work with designers to develop a vision for an exemplary early childhood centre with a focus on Education for Sustainability (EfS). The symposium provides insights into cross-disciplinary initiatives between QUT Early childhood and Design staff and students, who have worked together with the iconic Lone Pine Koala Sanctuary in Brisbane, to explore imperatives around EfS, including leadership and professionalism. This practical, real world project has seen all stakeholders engage in a focus on sustainability which has opened new ways of thinking about early childhood centre design. Cross-disciplinarity has created space to re-think the potential of the disciplines to interweave, and in so doing opened different ways for thinking about early childhood centres – their operation and their function. For the first time in Queensland, this project creates strategic alliances between EfS, childcare, business and sustainable design. EfS is essential for addressing local and global environmental issues and early childhood EfS research has been gaining international momentum, with governments nominating this area as having significant capacity to empower communities and promote change. While models for collaboration exist in the early childhood programs in Reggio Emilia, we offer sustainability as a unique and contemporary focus with immense potential to generate international and national interest. To date Early Childhood degree students enrolled in a leadership and management unit/subject have worked collaboratively with Design students to explore the sustainable design of the proposed Lone Pine early childhood centre. Providing students with a ‘real world’ project sees them re-positioned from ‘novice’ to ‘professional’, where their knowledge, expertise and perspectives are simultaneously validated and challenged. These learning experiences are enabling students to practice a new model of early childhood leadership, one that is vital for leading in an increasingly complex world. The symposium will be comprised of three discrete, though interconnected presentations, that work together to tell the story of this project. Three key facets of the project will be explored during the 90 minute session, as the perspectives of key stakeholders are shared. The first presentation (A/Prof Julie Davis, Dr Lyndal O’Gorman& Dr Megan Gibson) will outline the role of QUT School of Early Childhood staff and students, with attention to the ways in which the project was embedded in students’ work in the final year of their degree program of study. The second presentation (Ms Lindy Osborne) will provide insights into the Design students’ collaborative work in the project. Finally, the key role of the Lone Pine Koala Sanctuary and their commitment for EfS (Ms Peta Wilson & Dr Sue Elliott) will map out the philosophy that underpins the project. Together, the authors will conclude key project outcomes that have been achieved through this real-world, cross-disciplinary work.

Changes in phosphine sorption in wheat after storage at two temperatures.

BACKGROUND: Wheat can be stored for many months before being fumigated with phosphine to kill insects, so a study was undertaken to investigate whether the sorptive capacity of wheat changes as it ages. Wheat was stored at 15 or 25C and 55% RH for up to 5.5 months, and samples were fumigated at intervals to determine sorption. Sealed glass flasks (95% full) were injected with 1.5 mg L-1 of phosphine based on flask volume. Concentrations were monitored for 11 days beginning 2 h after injection. Some wheat samples were refumigated after a period of ventilation. Several fumigations of wheat were conducted to determine the pattern of sorption during the first 24 h. RESULTS: Phosphine concentration declined exponentially with time from 2 h after injection. Rate of sorption decreased with time spent in storage at either 15 or 25C and 55% RH. Rate of sorption tended to be lower when wheat was refumigated, but this could be explained by time in storage rather than by refumigation per se. The data from the 24 h fumigations did not fit a simple exponential decay equation. Instead, there was a rapid decline in the first hour, with phosphine concentration falling much more slowly thereafter. CONCLUSIONS: The results have implications for phosphine fumigation of insects in stored wheat. Both the time wheat has spent in storage and the temperature at which it has been stored are factors that must be considered when trying to understand the impact of sorption on phosphine concentrations in commercial fumigations.

Defect Sensitization of Combustion and Thermal Decomposition of Ammonium Perchlorate: Effect of Pelletizing Pressure and Dwell Time

A systematic study was undertaken on the combustion and thermal decomposition of pelletized Ammonium Perchlorate (AP) to investigate the effects of pelletizing pressure and dwell time. At constant pressure, increasing the dwell time results in an increase in the burning rate up to a maximum and thereafter decreases it. The dwell time required for the pellets to have maximum burning rate is a function of pressure. The maximum burning rate is the same for all the pressures used and is also unaffected by increasing, to the range 90-250 μ, the particle size of AP used. In order to explain the occurrence of a maximum in burning rate, pellets were examined for their thermal sensitivities, physical nature and the changes occurring during pelletization with dwell time and pressure. The variations are argued in terms of increasing density, formation of defects such as dislocations leading to an increase in the number of reactive sites, followed by their partial annihilation at longer dwell times due to flow of material during pelletization.

Austropleospora osteospermi gen. et sp nov and its host specificity and distribution on Chrysanthemoides monilifera ssp rotundata in Australia.

Hendersonia osteospermi was found for the first time in Australia on leaf spots of the introduced invasive plant Chrysanthemoides monilifera ssp. rotundata (bitou bush) in coastal regions of New South Wales. Pathogenicity tests on species from 11 tribes in the family Asteraceae, demonstrated that H. osteospermi caused severe necrosis on leaves and stems of C. monilifera ssp. rotundata and its congener C. monilifera ssp. monilifera (boneseed). Small necrotic spots also developed on Osteospermum fruticosum and Dimorphotheca cuneata in the Calenduleae and on Helianthus annuus (sunflower) in the Heliantheae. None of the other plant species tested developed leaf spots, although H. osteospermi was re-isolated from senescent leaves of Cynara scolymus (globe artichoke) in the Cynareae and Vernonia cinerea in the Vernonieae. Single ascospores from ascomata of a Pleospora-like fungus found on diseased stems of bitou bush produced H. osteospermi in culture, which proved the anamorph/teleomorph connection. The ITS region of both a single-ascospore isolate and a single-conidium isolate were sequenced and found to be identical. The taxonomic status of H. osteospermi is re-examined and Austropleospora osteospermi gen. et sp. nov. is described as its teleomorph based on morphology, host range tests and DNA sequence analysis. The potential of A. osteospermi for the biological control of bitou bush and boneseed in Australia is discussed.

A review of Taenaris Hubner (Lepidoptera: Nymphalidae: Amathusiinae) in Queensland, together with first Australian records for T. myops kirschi Staudinger and Elymnias agondas melanippe Grose-Smith (Satyrinae).

Species of the amathusiine genus Taenaris Hubner known to occur in Australia, predominantly from Torres Strait, are reviewed and illustrated. T. myops kirschi Staudinger is recorded for the first time in Australia from four male specimens collected on Dauan Island, Torres Strait. A female specimen of the satyrine Elymnias agondas melanippe Grose-Smith also collected from Dauan Island represents the first record of this taxon from Australia. The high degree of variation observed in the external facies of Taenaris from Torres Strait and reliable taxonomic separation of female specimens are discussed. Taenaris-like forms of the papilionid, Papilio aegeus ormenus Guerin-Meneville and E. a. melanippe from Torres Strait and Dauan Island respectively are illustrated and reviewed. The form of P. a. ormenus from Torres Strait that is most similar to Taenaris spp. is identified as form ormenus Guerin-Meneville variety onesimus Hewitson.

Expression and function of angiotensins in the regulation of intraocular pressure - an experimental study

Glaucoma is a multifactorial long-term ocular neuropathy associated with progressive loss of the visual field, retinal nerve fiber structural abnormalities and optic disc changes. Like arterial hypertension it is usually a symptomless disease, but if left untreated leads to visual disability and eventual blindness. All therapies currently used aim to lower intraocular pressure (IOP) in order to minimize cell death. Drugs with new mechanisms of action could protect glaucomatous eyes against blindness. Renin-angiotensin system (RAS) is known to regulate systemic blood pressure and compounds acting on it are in wide clinical use in the treatment of hypertension and heart failure but not yet in ophthalmological use. There are only few previous studies concerning intraocular RAS, though evidence is accumulating that drugs antagonizing RAS can also lower IOP, the only treatable risk factor in glaucoma. The main aim of this experimental study was to clarify the expression of the renin-angiotensin system in the eye tissues and to test its potential oculohypotensive effects and mechanisms. In addition, the possible relationship between the development of hypertension and IOP was evaluated in animal models. In conclusion, a novel angiotensin receptor type (Mas), as well as ACE2 enzyme- producing agonists for Mas, were described for the first time in the eye structures participating in the regulation of IOP. In addition, a Mas receptor agonist significantly reduced even normal IOP. The effect was abolished by a specific receptor antagonist. Intraocular, local RAS would thus to be involved in the regulation of IOP, probably even more in pathological conditions such as glaucoma though there was no unambiguous relationship between arterial and ocular hypertension. The findings suggest the potential as antiglaucomatous drugs of agents which increase ACE2 activity and the formation of angiotensin (1-7), or activate Mas receptors.

MOE and MOR assessment technologies for improving graded recovery of exotic pines in Australia.

This project was designed to provide the structural softwood processing industry with the basis for improved green and dry grading to allow maximise MGP grade yields, consistent product performance and reduced processing costs. To achieve this, advanced statistical techniques were used in conjunction with state-of-the-art property measurement systems. Specifically, the project aimed to make two significant steps forward for the Australian structural softwood industry: • assessment of technologies, both existing and novel, that may lead to selection of a consistent, reliable and accurate device for the log yard and green mill. The purpose is to more accurately identify and reject material that will not make a minimum grade of MGP10 downstream; • improved correlation of grading MOE and MOR parameters in the dry mill using new analytical methods and a combination of devices. The three populations tested were stiffness-limited radiata pine, strength-limited radiata pine and Caribbean pine. Resonance tests were conducted on logs prior to sawmilling, and on boards. Raw data from existing in-line systems were captured for the green and dry boards. The dataset was analysed using classical and advanced statistical tools to provide correlations between data sets and to develop efficient strength and stiffness prediction equations. Stiffness and strength prediction algorithms were developed from raw and combined parameters. Parameters were analysed for comparison of prediction capabilities using in-line parameters, off-line parameters and a combination of in-line and off-line parameters. The results show that acoustic resonance techniques have potential for log assessment, to sort for low stiffness and/or low strength, depending on the resource. From the log measurements, a strong correlation was found between the average static MOE of the dried boards within a log and the predicted value. These results have application in segregating logs into structural and non-structural uses. Some commercial technologies are already available for this application such as Hitman LG640. For green boards it was found that in-line and laboratory acoustic devices can provide a good prediction of dry static MOE and moderate prediction for MOR.There is high potential for segregating boards at this stage of processing. Grading after the log breakdown can improve significantly the effectiveness of the mill. Subsequently, reductions in non-structural volumes can be achieved. Depending on the resource it can be expected that a 5 to 8 % reduction in non structural boards won’t be dried with an associated saving of $70 to 85/m3. For dry boards, vibration and a standard Metriguard CLT/HCLT provided a similar level of prediction on stiffness limited resource. However, Metriguard provides a better strength prediction in strength limited resources (due to this equipment’s ability to measure local characteristics). The combination of grading equipment specifically for stiffness related predictors (Metriguard or vibration) with defect detection systems (optical or X-ray scanner) provides a higher level of prediction, especially for MOR. Several commercial technologies are already available for acoustic grading on board such those from Microtec, Luxscan, Falcon engineering or Dynalyse AB for example. Differing combinations of equipment, and their strategic location within the processing chain, can dramatically improve the efficiency of the mill, the level of which will vary depending of the resource. For example, an initial acoustic sorting on green boards combined with an optical scanner associated with an acoustic system for grading dry board can result in a large reduction of the proportion of low value low non-structural produced. The application of classical MLR on several predictors proved to be effective, in particular for MOR predictions. However, the usage of a modern statistics approach(chemometrics tools) such as PLS proved to be more efficient for improving the level of prediction. Compared to existing technologies, the results of the project indicate a good improvement potential for grading in the green mill, ahead of kiln drying and subsequent cost-adding processes. The next stage is the development and refinement of systems for this purpose.

Quantitative and molecular genetics of juvenile wood traits in radiata and slash/Caribbean pines.

The Juvenile Wood Initiative (JWI) project has been running successfully since July 2003 under a Research Agreement with FWPA and Letters of Association with the consortium partners STBA (Southern Tree Breeding Association), ArborGen and FPQ (Forestry Plantations Queensland). Over the last five and half years, JWI scientists in CSIRO, FPQ, and STBA have completed all 12 major milestones and 28 component milestones according to the project schedule. We have made benchmark progress in understanding the genetic control of wood formation and interrelationships among wood traits. The project has made 15 primary scientific findings and several results have been adopted by industry as summarized below. This progress was detailed in 10 technical reports to funding organizations and industry clients. Team scientists produced 16 scientific manuscripts (8 published, 1 in press, 2 submitted, and several others in the process of submission) and 15 conference papers or presentations. Primary Scientific Findings. The 15 major scientific findings related to wood science, inheritance and the genetic basis of juvenile wood traits are: 1. An optimal method to predict stiffness of standing trees in slash/Caribbean pine is to combine gravimetric basic density from 12 mm increment cores with a standing tree prediction of MoE using a time of flight acoustic tool. This was the most accurate and cheapest way to rank trees for breeding selection for slash/Caribbean hybrid pine. This method was also recommended for radiata pine. 2. Wood density breeding values were predicted for the first time in the STBA breeding population using a large sample of 7,078 trees (increment cores) and it was estimated that selection of the best 250 trees for deployment will produce wood density gains of 12.4%. 3. Large genetic variation for a suite of wood quality traits including density, MFA, spiral grain, shrinkage, acoustic and non-acoustic stiffness (MoE) for clear wood and standing trees were observed. Genetic gains of between 8 and 49% were predicted for these wood quality traits with selection intensity between 1 to 10% for radiata pine. 4. Site had a major effect on juvenile-mature wood transition age and the effect of selective breeding for a shorter juvenile wood formation phase was only moderate (about 10% genetic gain with 10% selection intensity, equivalent to about 2 years reduction of juvenile wood). 5. The study found no usable site by genotype interactions for the wood quality traits of density, MFA and MoE for both radiata and slash/Caribbean pines, suggesting that assessment of wood properties on one or two sites will provide reliable estimates of the genetic worth of individuals for use in future breeding. 6. There were significant and sizable genotype by environment interactions between the mainland and Tasmanian regions and within Tasmania for DBH and branch size. 7. Strong genetic correlations between rings for density, MFA and MoE for both radiata and slash/Caribbean pines were observed. This suggests that selection for improved wood properties in the innermost rings would also result in improvement of wood properties in the subsequent rings, as well as improved average performance of the entire core. 8. Strong genetic correlations between pure species and hybrid performance for each of the wood quality traits were observed in the hybrid pines. Parental performance can be used to identify the hybrid families which are most likely to have superior juvenile wood properties of the slash/Caribbean F1 hybrid in southeast Queensland. 9. Large unfavourable genetic correlations between growth and wood quality traits were a prominent feature in radiata pine, indicating that overcoming this unfavourable genetic correlation will be a major technical issue in progressing radiata pine breeding. 10. The project created the first radiata pine 18 k cDNA microarray and generated 5,952 radiata pine xylogenesis expressed sequence tags (ESTs) which assembled into 3,304 unigenes. 11. A total of 348 genes were identified as preferentially expressed genes in earlywood or latewood while a total of 168 genes were identified as preferentially expressed genes in either juvenile or mature wood. 12. Juvenile earlywood has a distinct transcriptome relative to other stages of wood development. 13. Discovered rapid decay of linkage disequilibrium (LD) in radiata pine with LD decaying to approximately 50% within 1,700 base pairs (within a typical gene). A total of 913 SNPS from sequencing 177,380 base pairs were identified for association genetic studies. 14. 149 SNPs from 44 genes and 255 SNPs from a further 51 genes (total 95 genes) were selected for association analysis with 62 wood traits, and 30 SNPs were shortlisted for their significant association with variation of wood quality traits (density, MFA and MoE) with individual significant SNPs accounting for between 1.9 and 9.7% of the total genetic variation in traits. 15. Index selection using breeding objectives was the most profitable selection method for radiata pine, but in the long term it may not be the most effective in dealing with negative genetic correlations between wood volume and quality traits. A combination of economic and biological approaches may be needed to deal with the strong adverse correlation.