Surface Emitting Distributed Feedback Quantum Cascade Laser around 8.3 mu m

We demonstrate surface emitting distributed feedback quantum cascade lasers emitting at wavelengths from 8.1 mu m at 90 K to 8.4 mu m at 210 K. The second-order metalized grating is carefully designed using a modified coupled-mode theory and fabricated by contact lithography. The devices show single mode behavior with a side mode suppression ratio above 18 dB at all working temperatures. At 90 K, the device emits an optical power of 101 mW from the surface and 199 mW from the edge. In addition, a double-lobe far-field pattern with a separation of 2.2 degrees is obtained in the direction along the waveguide.

High Characteristic Temperature InGaAsP/InP Tunnel Injection Multiple-Quantum-Well Lasers

We fabricate 1.5 mu m InGaAsP/InP tunnel injection multiple-quantum-well (TI-MQW) Fabry-Perot (F-P) ridge lasers. The laser heterostructures, including an inner cladding layer and an InP tunnel barrier layer, are grown by metal-organic chemical-vapor deposition (MOCVD). Characteristic temperature.. 0 of 160K at 20 degrees C is obtained for 500-mu m-long lasers. T-0 is measured as high as 88K in the temperature range of 15-75 degrees C. Cavity length dependence of T-0 is investigated.

Intersubband absorption energy shifts in 3-level system for asymmetric quantum well terahertz emitters

Intersubband absorption energy shifts in 3-level system stemming from depolarization and excitonlike effects are investigated. Analytically, the expressions we derive present good explanations to the conventional 2-level results and bare potential transition energy results; and numerical results show that they are more exact than the previous studies to describe the 3-level system depolarization and excitonlike shift (DES) character especially for higher carrier density (more than 8 x 10(11) cm(-2)). One interesting detail we find is that the "large blue" DES becomes "slight redshift" in the low doping limit (less than 1.9 x 10(11) cm(-2)), which may be neglected by the previous studies of intersubband transitions. Temperature character of DES in the step well structure is also numerically studied. Finally the above are applied to calculate asymmetric step quantum well structures. The two main functional aspects of terahertz (THz) emitters are discussed and several basic optimizing conditions are considered. By adjusting the well geometry parameters and material composition systematically, some optimized structures which satisfy all of the six conditions are recommended in tables. These optimizations may provide useful references to the design of 3-level-based optically pumping THz emitters.

Sequential coupling transport for the dark current of quantum dots-in-well infrared photodetectors

The dark current characteristics and temperature dependence for quantum dot infrared photodetectors have been investigated by comparing the dark current activation energies between two samples with identical structure of the dots-in-well in nanoscale but different microscale n-i-n environments. A sequential coupling transport mechanism for the dark current between the nanoscale and the microscale processes is proposed. The dark current is determined by the additive mode of two activation energies: E-a,E-micro from the built-in potential in the microscale and E-a,E-nano related to the thermally assisted tunneling in nanoscale. The activation energies E-a,E-micro and E-a,E-nano decrease exponentially and linearly with increasing applied electric field, respectively.

Strain effects on optical polarisation properties in (11(2)over-bar2) plane GaN films

We present the theoretical results of the electronic band structure of wurtzite GaN films under biaxial strains in the (11 (2) over bar2)-plane The calculations are performed by the kappa p perturbation theory approach through using the effective-mass Hamiltonian for an arbitrary direction The results show that the transition energies decrease with the biaxial strains changing from -0 5% to 0 5% For films of (11 (2) over bar2)-plane, the strains are expected to be anisotropic in the growth plane Such anisotropic strains give rise to valence band mixing which results in dramatic change in optical polarisation property The strain can also result in optical polarisation switching phenomena Finally, we discuss the applications of these properties to the (11 (2) over bar2) plane GaN based light emitting diode and lase diode

Effects of silicon incorporation on composition, structure and electric conductivity of cubic boron nitride thin films

We have achieved in-situ Si incorporation into cubic boron nitride (c-BN) thin films during ion beam assisted deposition. The effects of silicon incorporation on the composition, structure and electric conductivity of c-BN thin films were investigated by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and electrical measurements. The results suggest that the content of the cubic phase remains stable on the whole with the incorporation of Si up to a concentration of 3.3 at.%, and the higher Si concentrations lead to a gradual change from c-BN to hexagonal boron nitride. It is found that the introduced Si atoms only replace B atoms and combine with N atoms to form Si-N bonds, and no evidence of the existence of Si-B bonds is observed. The resistance of the Si-doped c-BN films gradually decreases with increasing Si concentration, and the resistivity of the c-BN film with 3.3 at.% Si is lowered by two orders of magnitude as compared to undoped samples.

requirement analysis of information and knowledge management in postmodern perspective on curriculum

National Basic Research Program of China; Chinese Academy of Sciences; Information Society Technologies; Institute of Computing Technology, Chinese Academy of Sciences; Zhuhai National Hi-tech Industrial Development Zone

Fabrication of Novel Superhydrophobic Surfaces and Water Droplet Bouncing Behavior - Part 1: Stable ZnO-PDMS Superhydrophobic Surface with Low Hysteresis Constructed Using ZnO Nanoparticles

A superhydrophobic surface has many advantages in micro/nanomechanical applications, such as low adhesion, low friction and high restitution coefficient, etc. In this paper, we introduce a novel and simple route to fabricate superhydrophobic surfaces using ZnO nanocrystals. First, tetrapod-like ZnO nanocrystals were prepared via a one-step, direct chemical vapor deposition (CVD) approach. The nanostructured ZnO material was characterized by scanning electron microscope (SEM) and X-ray diffraction (XRD) and the surface functionalized by aminopropyltriethoxysilane (APS) was found to be hydrophobic. Then the superhydrophobic surface was constructed by depositing uniformly ZnO hydrophobic nanoparticles (HNPs) on the Poly(dimethylsiloxane) (PDMS) film substrate. Water wettability study revealed a contact angle of 155.4 +/- 2 degrees for the superhydrophobic surface while about 110 degrees for pure smooth PDMS films. The hysteresis was quite low, only 3.1 +/- 0.3 degrees. Microscopic observations showed that the surface was covered by micro- and nano-scale ZnO particles. Compared to other approaches, this method is rather convenient and can be used to obtain a large area superhydrophobic surface. The high contact angle and low hysteresis could be attributed to the micro/nano structures of ZnO material; besides, the superhydrophobic property of the as-constructed ZnO-PDMS surface could be maintained for at least 6 months. (C) Koninklijke Brill NV, Leiden, 2010

Evolution of Localized Damage Zone in Heterogeneous Media

Evolution of localized damage zone is a key to catastrophic rupture in heterogeneous materials. In the present article, the evolutions of strain fields of rock specimens are investigated experimentally. The observed evolution of fluctuations and autocorrelations of strain fields under uniaxial compression demonstrates that the localization of deformation always appears ahead of catastrophic rupture. In particular, the localization evolves pronouncedly with increasing deformation in the rock experiments. By means of the definition of the zone with high strain rate and likely damage localization, it is found that the size of the localized zone decreases from the sample size at peak load to an eventual value. Actually, the deformation field beyond peak load is bound to suffer bifurcation, namely an elastic unloading part and a continuing but localized damage part will co-exist in series in a specimen. To describe this continuous bifurcation and localization process observed in experiments, a model on continuum mechanics is developed. The model can explain why the decreasing width of localized zone can lead stable deformation to unstable, but it still has not provided the complete equations governing the evolution of the localized zone.

The Effects of Roughness on Adhesion Hysteresis

Adhesion hysteresis is defined as the difference between the work needed to separate two surfaces and that originally gained on bringing them together. Adhesion hysteresis is a common phenomenon in most surface/interface interactions. This paper studies the effects of surface roughness on adhesion hysteresis. We assumed that the surface asperity height distribution is Gaussian. Numerical simulations based on Fuller's model showed that adhesion hysteresis depended upon a single dimensionless parameter, the adhesion parameter, which represents the statistical average of a competition between the compressive forces exerted by the higher asperities, which are trying to separate the surfaces, and the adhesion forces of the lower asperities which are trying to hold the surfaces together. (C) Koninklijke Brill NV, Leiden, 2010

Precursor Film in Dynamic Wetting, Electrowetting, and Electro-Elasto-Capillarity

Dynamic wetting and electrowetting are explored using molecular dynamics simulations. The propagation of the precursor film (PF) is fast and obeys the power law with respect to time. Against the former studies, we find the PF is no slip and solidlike. As an important application of the PF, the electro-elasto-capillarity, which is a good candidate for drug delivery at the micro- or nanoscale, is simulated and realized for the first time. Our findings may be one of the answers to the Huh-Scriven paradox and expand our knowledge of dynamic wetting and electrowetting.

Wurtzite-to-tetragonal structure phase transformation and size effect in ZnO nanorods

The deformation of [0001]-oriented ZnO nanorods with hexagonal cross sections under uniaxial tensile loading is analyzed through molecular statistical thermodynamics (MST) simulations. The focus is on the size dependence of mechanical behavior in ZnO nanorods with diameters ranging from 1.95 to 17.5 nm. An irreversible phase transformation from the wurtzite (P6(3)mc space group) structure to a tetragonal structure (P4(2)/mnm space group) occurs during the tensile loading process. Young's modulus before the transformation demonstrates a size dependence consistent with what is observed in experiments. A stronger size dependence of response is seen after the transformation and is attributed to the polycrystalline nature of the transformed structure. A comparison of the MST and molecular dynamics (MD) methods shows that MST is 60 times faster than MD and yields results consistent with the results of MD.

Mechanical Behavior of Nanometer Ni by Simulating Nanoindentation

An indentation simulation of the crystal Ni is carried out by a molecular dynamics technique (MD) to study the mechanical behavior at nanometer scales. Indenter tips with both sphere shape and conical shape with 60 cone angle are used, and simulation samples with different crystal orientations are adopted. Some defects such as dislocations and point defects are observed. It is found that nucleated defects (dislocations, amorphous atoms) are from the local region near the pin tip or the sample surface. The temperature distribution of the local region is analyzed and it can explain our MD simulation results.

细胞粘附力敏感性的微观力学模型

<正>Focal adhesions(FAs)are large,multiprotein complexs that provides linkers between cytoskeleton to the extracellular matrix(ECM).Cells sense and respond to forces through