Role and regulatory mechanisms of heat shock factor 2

Protein homeostasis is essential for cells to prosper and survive. Various forms of stress, such as elevated temperatures, oxidative stress, heavy metals or bacterial infections cause protein damage, which might lead to improper folding and formation of toxic protein aggregates. Protein aggregation is associated with serious pathological conditions such as Alzheimer’s and Huntington’s disease. The heat shock response is a defense mechanism that protects the cell against protein-damaging stress. Its ancient origin and high conservation among eukaryotes suggest that the response is crucial for survival. The main regulator of the heat shock response is the transcription factor heat shock factor 1 (HSF1), which induces transcription of genes encoding protective molecular chaperones. In vertebrates, a family of four HSFs exists (HSF1-4), with versatile functions not only in coping with acute stress, but also in development, longevity and cancer. Thus, knowledge of the HSFs will aid in our understanding on how cells survive suboptimal circumstances, but will also provide insights into normal physiological processes as well as diseaseassociated conditions. In this study, the function and regulation of HSF2 have been investigated. Earlier gene inactivation experiments in mice have revealed roles for HSF2 in development, particularly in corticogenesis and spermatogenesis. Here, we demonstrate that HSF2 holds a role also in the heat shock response and influences stress-induced expression of heat shock proteins. Intriguingly, DNA-binding activity of HSF2 upon stress was dependent on the presence of intact HSF1, suggesting functional interplay between HSF1 and HSF2. The underlying mechanism for this phenomenon could be configuration of heterotrimers between the two factors, a possibility that was experimentally verified. By changing the levels of HSF2, the expression of HSF1-HSF2 heterotrimer target genes was altered, implementing HSF2 as a modulator of HSF-mediated transcription. The results further indicate that HSF2 activity is dependent on its concentration, which led us to ask the question of how accurate HSF2 levels are achieved. Using mouse spermatogenesis as a model system, HSF2 was found to be under direct control of miR-18, a miRNA belonging to the miR-17~92 cluster/Oncomir-1 and whose physiological function had remained unclear. Investigations on spermatogenesis are severely hampered by the lack of cell systems that would mimic the complex differentiation processes that constitute male germ cell development. Therefore, to verify that HSF2 is regulated by miR-18 in spermatogenesis, a novel method named T-GIST (Transfection of Germ cells in Intact Seminiferous Tubules) was developed. Employing this method, the functional consequences of miR-18-mediated regulation in vivo were demonstrated; inhibition of miR- 18 led to increased expression of HSF2 and altered the expression of HSF2 target genes Ssty2 and Speer4a. Consequently, the results link miR-18 to HSF2-mediated processes such as germ cell maturation and quality control and provide miR-18 with a physiological role in gene expression during spermatogenesis.Taken together, this study presents compelling evidence that HSF2 is a transcriptional regulator in the heat shock response and establishes the concept of physical interplay between HSF2 and HSF1 and functional consequences thereof. This is also the first study describing miRNA-mediated regulation of an HSF.

Shewhart's control charts and process capability ratio applied to a sewage treatment station

The current study used statistical methods of quality control to evaluate the performance of a sewage treatment station. The concerned station is located in Cascavel city, Paraná State. The evaluated parameters were hydrogenionic potential, settleable solids, total suspended solids, chemical oxygen demand and biochemical oxygen demand in five days. Statistical analysis was performed through Shewhart control charts and process capability ratio. According to Shewhart charts, only the BOD(5.20) variable was under statistical control. Through capability ratios, we observed that except for pH the sewage treatment station is not capable to produce effluents under characteristics that fulfill specifications or standard launching required by environmental legislation.

Laatu ja tuottavuus hitsaavassa verkostossa

Diplomityössä tarkastellaan laadun ja tuottavuuden parantamisen keinoja hitsaavassa verkostossa MIG/MAG-hitsauksen osalta. Työn taustalla vaikuttaa Total Welding Management -menetelmä, mikä on hitsaustoimintojen kokonaisvaltaiseen johtamiseen ja hallintaan kehitetty toimintamalli. Työn teoriaosassa käsitellään laatuajattelua ja yritysyhteistyötä hitsaavan teollisuuden yrityskentässä sekä hitsauskustannuksiin vaikuttavia tekijöitä. Tutkimusosuus sisältää yritysverkoston nykytilan tarkastelun sekä kehitystoimenpiteitä kohti verkoston yhteistä toimintamallia saavuttaa tehokas ja kannattava yhteistyö. Hitsaustyön kustannukset määritetään suurelta osin suunnittelussa. Laatuun voidaan vaikuttaa merkittävästi hitsaustyötä edeltävissä toiminnoissa sekä hitsaajan työn tukemisella. Kokonaisvaltaisen hyödyn saavuttaminen hitsaustyön tuottavuuden parantamisessa vaatii kaikkien toimintojen tarkastelua sen sijaan, että tehostetaan vain hitsaamon toimintaa. Itse hitsaus voi olla vain pieni osa hitsaustoimintojen kokonaishallintaa. Toimintamallin luominen laadunvarmistukseen, suunnittelun ja valmistuksen yhteistyöhön sekä hitsaustoimintojen hallintaan mahdollistaa hitsaavan verkoston toiminnan tehostamisen sekä laadun paranemisen. Tämä saavutetaan viemällä toimintamalli osaksi jokapäiväistä työtä, lähelle valmistusta, ja ohjeistamalla, että jokainen tietää kuinka toimia. Esimerkiksi työssä tarkastellun yhden tuotteen osalta ohjeistus turhan työn vähentämiseksi tuotti 19 % tuotannon kasvun työvuoron aikana. Tilaus-toimitusketjun tuottavuuteen ja kannattavuuteen voidaan vaikuttaa merkittävästi käymällä läpi konkreettisesti valmistettavat tuotteet ja niihin liittyvät toiminnot. Diplomityössä tehtyjen tarkastelujen ja havaintojen avulla käytännön työ tulee jatkumaan yritysverkostossa tapahtuvassa kehitystyössä.

Modeling and Control of the Power Conversion Unit in a Solid Oxide Fuel Cell Environment

In this doctoral thesis, a power conversion unit for a 10 kWsolid oxide fuel cell is modeled, and a suitable control system is designed. The need for research was identified based on an observation that there was no information available about the characteristics of the solid oxide fuel cell from the perspective of power electronics and the control system, and suitable control methods had not previously been studied in the literature. In addition, because of the digital implementation of the control system, the inherent characteristics of the digital system had to be taken into account in the characteristics of the solid oxide fuel cell (SOFC). The characteristics of the solid oxide fuel cell as well the methods for the modeling and control of the DC/DC converter and the grid converter are studied by a literature survey. Based on the survey, the characteristics of the SOFC as an electrical power source are identified, and a solution to the interfacing of the SOFC in distributed generation is proposed. A mathematical model of the power conversion unit is provided, and the control design for the DC/DC converter and the grid converter is made based on the proposed interfacing solution. The limit cycling phenomenon is identified as a source of low-frequency current ripple, which is found to be insignificant when connected to a grid-tied converter. A method to mitigate a second harmonic originating from the grid interface is proposed, and practical considerations of the operation with the solid oxide fuel cell plant are presented. At the theoretical level, the thesis discusses and summarizes the methods to successfully derive a model for a DC/DC converter, a grid converter, and a power conversion unit. The results of this doctoral thesis can also be used in other applications, and the models and methods can be adopted to similar applications such as photovoltaic systems. When comparing the results with the objectives of the doctoral thesis, we may conclude that the objectives set for the work are met. In this doctoral thesis, theoretical and practical guidelines are presented for the successful control design to connect a SOFC-based distributed generation plant to the utility grid.

One chip solution for low-cost active magnetic bearing system

In this work the implementation of the active magnetic bearing control system in a single FPGA is studied. Requirements for the full magnetic bearing control system are reviewed. Different control methods for active magnetic bearings are described shortly. Flux and the current base controllers are implemented in a FPGA. Suitability of the con-trollers for a low-cost magnetic bearing application is studied. Floating-point arithmetic’s are used in the controllers to ease designing burden and improve calculation precision. Per-formance of the flux controller is verified with simulations.

Silloitushitsauksen robotisointi

Tämän diplomityön tavoitteena oli tutkia ja selvittää kuormakoneen takarunkorakenteen silloitushitsauksen robotisointia. Työ päätettiin rajata koskemaan vain tiettyä moduulia takarungosta. Työssä kartoitettiin tarvittava laitteisto, selvitettiin runkomoduulin silloitusajat sekä arvioitiin investoinnin kannattavuutta. Silloituksen suorittavan järjestelmän vaatimuksena oli, että sen tulee asettaa osat paikoilleen hitsauskiinnittimeen ja tehdä tarvittavat silloitushitsaukset automaattisesti. Sopivaksi laitteistoksi osoittautui taloudellisuuden ja toiminnallisuuden näkökulmasta yhdestä kappaleenkäsittely- sekä hitsausrobotista muodostuva järjestelmä. Kappaleenkäsittelijän ohjauksessa käytetään konenäköä sekä osien paikannuksessa että laadunvarmistuksessa. Robotit liikkuvat yhteisellä lineaariradalla, jonka rinnalla on kappaleenkäsittelylaitteistoja hitsauskiinnittimineen. Robotisoinnin käyttöönotolla yhden takarungon moduulien kokoonpanoon ja silloitukseen käytettävä aika pienenee alle puoleen manuaaliseen työhön verrattuna. Näin saavutetaan merkittäviä kustannussäästöjä. Lisäksi hitsauskiinnittimet voivat olla verrattain yksinkertaisia manuaalityöhön verrattuna, jolloin myös säästetään työkaluinvestoinneissa. Robotisointiprojektin jatkotoimenpiteitä ovat laajamittaiset tuotantosimulaatiot layoutin, laitteiston sekä työkiertojen tarkaksi määrittämiseksi. Lisäksi itse tuotetta on muokattava paremmin robottisilloitukseen sopivaksi.

Control of Structures with Cubic and Quadratic Non-Linearities with Time Delay Consideration

This paper studies the effect of time delay on the active non-linear control of dynamically loaded flexible structures. The behavior of non-linear systems under state feedback control, considering a fixed time delay for the control force, is investigated. A control method based on non-linear optimal control, using a tensorial formulation and state feedback control is used. The state equations and the control forces are expressed in polynomial form and a performance index, quadratic in both state vector and control forces, is used. General polynomial representations of the non-linear control law are obtained and implemented for control algorithms up to the fifth order. This methodology is applied to systems with quadratic and cubic non-linearities. Strongly non-linear systems are tested and the effectiveness of the control system including a delay for the application of control forces is discussed. Numerical results indicate that the adopted control algorithm can be efficient for non-linear systems, chiefly in the presence of strong non-linearities but increasing time delay reduces the efficiency of the control system. Numerical results emphasize the importance of considering time delay in the project of active structural control systems.

Speed Control of an Autonomous Mobile Robot: Comparison between a PID Control and a Control Using Fuzzy Logic

An Autonomous Mobile Robot battery driven, with two traction wheels and a steering wheel is being developed. This Robot central control is regulated by an IPC, which controls every function of security, steering, positioning localization and driving. Each traction wheel is operated by a DC motor with independent control system. This system is made up of a chopper, an encoder and a microcomputer. The IPC transmits the velocity values and acceleration ramp references to the PIC microcontrollers. As each traction wheel control is independent, it's possible to obtain different speed values for each wheel. This process facilities the direction and drive changes. Two different strategies for speed velocity control were implemented; one works with PID, and the other with fuzzy logic. There were no changes in circuits and feedback control, except for the PIC microcontroller software. Comparing the two different speed control strategies the results were equivalent. However, in relation to the development and implementation of these strategies, the difficulties were bigger to implement the PID control.

Simulation of Active Control Using Fuzzy Logic Applied to a Pulse Combustor

This work analyzes an active fuzzy logic control system in a Rijke type pulse combustor. During the system development, a study of the existing types of control for pulse combustion was carried out and a simulation model was implemented to be used with the package Matlab and Simulink. Blocks which were not available in the simulator library were developed. A fuzzy controller was developed and its membership functions and inference rules were established. The obtained simulation showed that fuzzy logic is viable in the control of combustion instabilities. The obtained results indicated that the control system responded to pulses in an efficient and desirable way. It was verified that the system needed approximately 0.2 s to increase the tube internal pressure from 30 to 90 mbar, with an assumed total delay of 2 ms. The effects of delay variation were studied. Convergence was always obtained and general performance was not affected by the delay. The controller sends a pressure signal in phase with the Rijke tube internal pressure signal, through the speakers, when an increase the oscillations pressure amplitude is desired. On the other hand, when a decrease of the tube internal pressure amplitude is desired, the controller sends a signal 180º out of phase.

Hitsaustuotannon kehittäminen tuulivoimalan tornin valmistuksessa

Tuulivoima on Euroopassa nopeimmin kasvava energian tuotantomuoto. Tuulivoimateollisuuden arvioidaan kasvavan Suomessa huomattavasti lähivuosien aikana ennakoidun syöttötariffipäätöksen myötä, jolloin kilpailu alalla tulee kasvamaan. Tavoitteena oli kehittää tuulivoimalan tornin valmistusta Levator Oy:ssä hitsaustuotantoa tehostamalla ja tuotannon ohjattavuutta parantamalla. Kehitystyöhön kuului toisen hitsauslinjan käyttöönoton suunnittelu ja ohjeiston laatiminen työnjohdolle. Toisen hitsauslinjan käyttöönoton suunnittelun tarkoituksena oli suunnitella muutokset nykyiseen tuotantoon uuden linjan käyttöönoton mahdollistamiseksi. Suunnittelu aloitettiin valitsemalla hitsausprosessit, jonka jälkeen suunniteltiin laitetarpeet työvaihe-analyysien pohjalta. Tuotantolayout muutettiin nykyisestä funktionaalisesta tuotannosta tuotantosoluista koostuvaksi tuotantolinjaksi, jolloin materiaalien virtautus parani huomattavasti. Tuotannon ohjaustavaksi valittiin kapeikko-ohjaus. Ohjeiston laatimisen tarkoituksena oli kerätä ja dokumentoida kaikki tuotannossa tarvittava tieto. Ohjeiston sisältää laadunohjaus, materiaalivirtojen ohjaus ja työnohjaus osiot, joiden tarkoituksena on helpottaa työnjohtamista. Ohjeisto määrittelee yhtenäiset tuotannon toimintatavat, jolloin tuotannon ohjattavuus helpottuu. Tavoitteet täyttyivät, kun toisen tuotantolinjan käyttöönoton vaatimat muutokset aloitettiin suunnitelmien mukaisesti syyskuussa 2009. Ohjeiston sisältö saatiin määriteltyä ja eri osioiden pilotit saatiin valmiiksi joulukuun aikana. Tuotannon ohjattavuus kehittyi huomattavasti ja samalla tuottavuus parani merkittävästi.

Adaptive control of Hydraulic Drive

Adaptive control systems are one of the most significant research directions of modern control theory. It is well known that every mechanical appliance’s behavior noticeably depends on environmental changes, functioning-mode parameter changes and changes in technical characteristics of internal functional devices. An adaptive controller involved in control process allows reducing an influence of such changes. In spite of this such type of control methods is applied seldom due to specifics of a controller designing. The work presented in this paper shows the design process of the adaptive controller built by Lyapunov’s function method for the Hydraulic Drive. The calculation needed and the modeling were conducting with MATLAB® software including Simulink® and Symbolic Math Toolbox™ etc. In the work there was applied the Jacobi matrix linearization of the object’s mathematical model and derivation of the suitable reference models based on Newton’s characteristic polynomial. The intelligent adaptive to nonlinearities algorithm for solving Lyapunov’s equation was developed. Developed algorithm works properly but considered plant is not met requirement of functioning with. The results showed confirmation that adaptive systems application significantly increases possibilities in use devices and might be used for correction a system’s behavior dynamics.

Dual light barrier method for six degrees of freedom tool center point calibration of an industrial robot

Tool center point calibration is a known problem in industrial robotics. The major focus of academic research is to enhance the accuracy and repeatability of next generation robots. However, operators of currently available robots are working within the limits of the robot´s repeatability and require calibration methods suitable for these basic applications. This study was conducted in association with Stresstech Oy, which provides solutions for manufacturing quality control. Their sensor, based on the Barkhausen noise effect, requires accurate positioning. The accuracy requirement admits a tool center point calibration problem if measurements are executed with an industrial robot. Multiple possibilities are available in the market for automatic tool center point calibration. Manufacturers provide customized calibrators to most robot types and tools. With the handmade sensors and multiple robot types that Stresstech uses, this would require great deal of labor. This thesis introduces a calibration method that is suitable for all robots which have two digital input ports free. It functions with the traditional method of using a light barrier to detect the tool in the robot coordinate system. However, this method utilizes two parallel light barriers to simultaneously measure and detect the center axis of the tool. Rotations about two axes are defined with the center axis. The last rotation about the Z-axis is calculated for tools that have different width of X- and Y-axes. The results indicate that this method is suitable for calibrating the geometric tool center point of a Barkhausen noise sensor. In the repeatability tests, a standard deviation inside robot repeatability was acquired. The Barkhausen noise signal was also evaluated after recalibration and the results indicate correct calibration. However, future studies should be conducted using a more accurate manipulator, since the method employs the robot itself as a measuring device.

Stiffness based trajectory planning and feedforward based vibration suppression control of parallel robot machines

The dissertation proposes two control strategies, which include the trajectory planning and vibration suppression, for a kinematic redundant serial-parallel robot machine, with the aim of attaining the satisfactory machining performance. For a given prescribed trajectory of the robot's end-effector in the Cartesian space, a set of trajectories in the robot's joint space are generated based on the best stiffness performance of the robot along the prescribed trajectory. To construct the required system-wide analytical stiffness model for the serial-parallel robot machine, a variant of the virtual joint method (VJM) is proposed in the dissertation. The modified method is an evolution of Gosselin's lumped model that can account for the deformations of a flexible link in more directions. The effectiveness of this VJM variant is validated by comparing the computed stiffness results of a flexible link with the those of a matrix structural analysis (MSA) method. The comparison shows that the numerical results from both methods on an individual flexible beam are almost identical, which, in some sense, provides mutual validation. The most prominent advantage of the presented VJM variant compared with the MSA method is that it can be applied in a flexible structure system with complicated kinematics formed in terms of flexible serial links and joints. Moreover, by combining the VJM variant and the virtual work principle, a systemwide analytical stiffness model can be easily obtained for mechanisms with both serial kinematics and parallel kinematics. In the dissertation, a system-wide stiffness model of a kinematic redundant serial-parallel robot machine is constructed based on integration of the VJM variant and the virtual work principle. Numerical results of its stiffness performance are reported. For a kinematic redundant robot, to generate a set of feasible joints' trajectories for a prescribed trajectory of its end-effector, its system-wide stiffness performance is taken as the constraint in the joints trajectory planning in the dissertation. For a prescribed location of the end-effector, the robot permits an infinite number of inverse solutions, which consequently yields infinite kinds of stiffness performance. Therefore, a differential evolution (DE) algorithm in which the positions of redundant joints in the kinematics are taken as input variables was employed to search for the best stiffness performance of the robot. Numerical results of the generated joint trajectories are given for a kinematic redundant serial-parallel robot machine, IWR (Intersector Welding/Cutting Robot), when a particular trajectory of its end-effector has been prescribed. The numerical results show that the joint trajectories generated based on the stiffness optimization are feasible for realization in the control system since they are acceptably smooth. The results imply that the stiffness performance of the robot machine deviates smoothly with respect to the kinematic configuration in the adjacent domain of its best stiffness performance. To suppress the vibration of the robot machine due to varying cutting force during the machining process, this dissertation proposed a feedforward control strategy, which is constructed based on the derived inverse dynamics model of target system. The effectiveness of applying such a feedforward control in the vibration suppression has been validated in a parallel manipulator in the software environment. The experimental study of such a feedforward control has also been included in the dissertation. The difficulties of modelling the actual system due to the unknown components in its dynamics is noticed. As a solution, a back propagation (BP) neural network is proposed for identification of the unknown components of the dynamics model of the target system. To train such a BP neural network, a modified Levenberg-Marquardt algorithm that can utilize an experimental input-output data set of the entire dynamic system is introduced in the dissertation. Validation of the BP neural network and the modified Levenberg- Marquardt algorithm is done, respectively, by a sinusoidal output approximation, a second order system parameters estimation, and a friction model estimation of a parallel manipulator, which represent three different application aspects of this method.

Tuotantoympäristön jatkuva parantaminen

Tutkimuksen tavoitteena oli luoda kohdeyritykseen toimintamalli, jonka avulla saadaan osallistettua työntekijät, tiiminvetäjät ja työnjohto tuotannon jatkuvaan parantamiseen sekä parannettua tuotannon takaisinkytkentää tiimitasolla. Tutkimus rajattiin pilottitiimiin sekä tiimissä olevien työpisteiden kautta reititettyihin tuotteisiin. Ennen tutkimuksen aloitusta yrityksellä oli jo olemassa sähköinen aloitejärjestelmä, mutta sen käyttö oli organisaation uudelleen järjestelyjen myötä vähentynyt. Tutkimuksen teoriaosassa tutustuttiin jatkuvan parantamisen kulttuuriin ja työkaluihin. Lisäksi tutustuttiin laadunhallinnan sisältöön, käsitteistöön ja laadunvalvontatyökaluihin sekä tuotannon mittareihin. Teorian pohjalta tutkimuksessa luotiin jatkuvan parantamisen toimintamalli, joka tunnistaa ja eliminoi prosessissa olevaa hukkaa osallistamalla pilottitiimin työntekijöitä hukkakorttien avulla. Lisäksi tutkimuksessa luotiin toimintamalli tuotannon kehitysideoiden raportointiin ja käsittelyyn. Tuotannon takaisinkytkentää kehitettiin luomalla pilottitiimiin tuloskortti sekä perustamalla yritykseen päiväkatsauskäytäntö. Tutkimuksessa suoritettiin myös toimihenkilötason kehitysprojekteja käyttäen apuna teoriassa esiteltyjä malleja ja työkaluja. Tuloksena saatiin toimintamalli, joka tuottaa työntekijämäärään suhteutettuna enemmän kehitysideoita sekä käsittelee ne tehokkaammin kuin sähköinen aloitejärjestelmä. Hukkakorteilla toteutetun hukan raportoinnin kautta tunnistettiin ja raportoitiin seitsemän viikon tarkasteluajanjakson aikana yhteensä 23,6 tuntia hukka-aikaa. Tiimin tuloskortin avulla tiimin työntekijät pystyivät viikkotasolla seuraamaan oman tiiminsä suorituskykyä tavoitearvoihin verrattuna. Tämä näkyi muun muassa tiimin suoritustason nousuna. Kehitysprojektien avulla saatiin parannettua pilottitiimin toiminnan ja tuotteiden laatua. Päiväkatsauskäytännön avulla saatiin osallistettua tiiminvetäjät ongelmaratkaisuun sekä tuotannon suorituskyvyn varmistamiseen.

Modelling Cutting States in Rough Turning of 34CrNiMo6 Steel

Rough turning is an important form of manufacturing cylinder-symmetric parts. Thus far, increasing the level of automation in rough turning has included process monitoring methods or adaptive turning control methods that aim to keep the process conditions constant. However, in order to improve process safety, quality and efficiency, an adaptive turning control should be transformed into an intelligent machining system optimizing cutting values to match process conditions or to actively seek to improve process conditions. In this study, primary and secondary chatter and chip formation are studied to understand how to measure the effect of these phenomena to the process conditions and how to avoid undesired cutting conditions. The concept of cutting state is used to address the combination of these phenomena and the current use of the power capacity of the lathe. The measures to the phenomena are not developed based on physical measures, but instead, the severity of the measures is modelled against expert opinion. Based on the concept of cutting state, an expert system style fuzzy control system capable of optimizing the cutting process was created. Important aspects of the system include the capability to adapt to several cutting phenomena appearing at once, even if the said phenomena would potentially require conflicting control action.