Ethanol oxidation reaction on PtCeO(2)/C electrocatalysts prepared by the polymeric precursor method

This paper presents a study of the electrocatalysis of ethanol oxidation reactions in an acidic medium on Pt-CeO(2)/C (20 wt.% of Pt-CeO(2) on carbon XC-72R), prepared in different mass ratios by the polymeric precursor method. The mass ratios between Pt and CeO(2) (3:1, 2:1, 1:1, 1:2, 1:3) were confirmed by Energy Dispersive X-ray Analysis (EDAX). X-ray diffraction (XRD) structural characterization data shows that the Pt-CeO(2)/C catalysts are composed of nanosized polycrystalline non-alloyed deposits, from which reflections corresponding to the fcc (Pt) and fluorite (CeO(2)) structures were clearly observed. The mean crystallite sizes calculated from XRD data revealed that, independent of the mass ratio, a value close to 3 nm was obtained for the CeO(2) particles. For Pt, the mean crystallite sizes were dependent on the ratio of this metal in the catalysts. Low platinum ratios resulted in small crystallites. and high Pt proportions resulted in larger crystallites. The size distributions of the catalysts particles, determined by XRD, were confirmed by Transmission Electron Microscope (TEM) imaging. Cyclic voltammetry and chronoamperometic experiments were used to evaluate the electrocatalytic performance of the different materials. In all cases, except Pt-CeO(2)/C 1:1, the Pt-Ceo(2)/C catalysts exhibited improved performance when compared with Pt/C. The best result was obtained for the Pt-CeO(2)/C 1:3 catalyst, which gave better results than the Pt-Ru/C (Etek) catalyst. (C) 2009 Elsevier B.V. All rights reserved.

Identifiering av parametrar till ackumulatortanken Solus1050 från consolar - en metodbeskrivning

This report describes the work done creating a computer model of a kombi tank from Consolar. The model was created with Presim/Trnsys and Fittrn and DF were used to identify the parameters. Measurements were carried out and were used to identify the values of the parameters in the model. The identifications were first done for every circuit separately. After that, all parameters are normally identified together using all the measurements. Finally the model should be compared with other measurements, preferable realistic ones. The two last steps have not yet been carried out, because of problems finding a good model for the domestic hot water circuit.The model of the domestic hot water circuit give relatively good results for low flows at 5 l/min, but is not good for higher flows. In the report suggestions for improving the model are given. However, there was not enough time to test this within the project as much time was spent trying to solve problems with the model crashing. Suggestions for improving the model for the domestic circuit are given in chapter 4.4. The improved equations that are to be used in the improved model are given by equation 4.18, 4.19 and 4.22.Also for the boiler circuit and the solar circuit there are improvements that can be done. The model presented here has a few shortcomings, but with some extra work, an improved model can be created. In the attachment (Bilaga 1) is a description of the used model and all the identified parameters.A qualitative assessment of the store was also performed based on the measurements and the modelling carried out. The following summary of this can be given: Hot Water PreparationThe principle for controlling the flow on the primary side seems to work well in order to achieve good stratification. Temperatures in the bottom of the store after a short use of hot water, at a coldwater temperature of 12°C, was around 28-30°C. This was almost independent of the temperature in the store and the DHW-flow.The measured UA-values of the heat exchangers are not very reliable, but indicates that the heat transfer rates are much better than for the Conus 500, and in the same range as for other stores tested at SERC.The function of the mixing valve is not perfect (see diagram 4.3, where Tout1 is the outlet hot water temperature, and Tdhwo and Tdhw1 is the inlet temperature to the hot and cold side of the valve respectively). The outlet temperature varies a lot with different temperatures in the storage and is going down from 61°C to 47°C before the cold port is fully closed. This gives a problem to find a suitable temperature setting and gives also a risk that the auxiliary heating is increased instead of the set temperature of the valve, when the hot water temperature is to low.Collector circuitThe UA-value of the collector heat exchanger is much higher than the value for Conus 500, and in the same range as the heat exchangers in other stores tested at SERC.Boiler circuitThe valve in the boiler circuit is used to supply water from the boiler at two different heights, depending on the temperature of the water. At temperatures from the boiler above 58.2°C, all the water is injected to the upper inlet. At temperatures below 53.9°C all the water is injected to the lower inlet. At 56°C the water flow is equally divided between the two inlets. Detailed studies of the behaviour at the upper inlet shows that better accuracy of the model would have been achieved using three double ports in the model instead of two. The shape of the upper inlet makes turbulence, that could be modelled using two different inlets. Heat lossesThe heat losses per m3 are much smaller for the Solus 1050, than for the Conus 500 Storage. However, they are higher than those for some good stores tested at SERC. The pipes that are penetrating the insulation give air leakage and cold bridges, which could be a major part of the losses from the storage. The identified losses from the bottom of the storage are exceptionally high, but have less importance for the heat losses, due to the lower temperatures in the bottom. High losses from the bottom can be caused by air leakage through the insulation at the pipe connections of the storage.

November 2001: P.A.S.C.A.L: The Cooperative Spirit

http://digitalcommons.winthrop.edu/deanscorner/1014/thumbnail.jpg

O outro lado de cá: histórias e memórias de Cachoeira da Prata

O principal objetivo dessa dissertação é analisar, através de um estudo caso, como a questão do “preconceito intergrupal” pode ser percebida no desenvolvimento histórico de pequenos municípios brasileiros. Escolhendo a história da memória da cidade de Cachoeira da Prata como objeto central, buscamos discutir como ocorreu o processo de diferenciação social da pequena comunidade formada pelos descendentes do ex-escravo Nicolau Teixeira do restante da cidade. Para tanto, dividimos a dissertação em duas partes. A primeira é formada pelos três primeiros capítulos, nos quais apresentamos a vila fabril de Cachoeira de Macacos como o cenário, no qual o cel. Américo Teixeira é identificado como o líder maior de um projeto de domínio político e industrial que deixou marcas duradouras na memória da população mais antiga da cidade. Nesse contexto, buscamos discutir como o fenômeno do pós-emancipação da escravidão se manifestou na localidade, analisando parte da trajetória de vida do ex-escravo Nicolau Teixeira, um leal apoiador do projeto político do cel. Américo, que se tornou, na primeira metade do século XX, o patriarca de uma comunidade criada nas imediações da antiga vila fabril. Na segunda parte, composta exclusivamente pelo quarto capítulo, discutimos de maneira conjugada, a história da diferenciação social da comunidade e diferentes posicionamentos políticos e metodológicos que adotamos ao longo da pesquisa. Após essa análise, concluímos que só é possível entender os meandros do processo que levou os descendentes de Nicolau Teixeira à condição de exclusão social após percebê-los como atores capazes de elaborar narrativas e representações que auxiliam a população de Cachoeira da Prata a conhecer um “outro lado” da história local.

Análise de projetos de investimentos : uma abordagem teórico-prática

The objective of this work is to search a real case of capital budgeting, relating the practical technical aspects of the elaboration of project, with theoretical referential and following secondary objectives: (i) to analyze the relations established between the bibliographical material and the found practical technical problems of capital budgeting in the enterprise; (ii) to search and to describe the necessary pacing to the economic and financial elaboration of an project, from the prospecting of the demand, the projection of revenues and expenditures and the evaluation of the necessary investments to its development; (iii) to relate and to exemplify the influences of the restrictions presented for the methods of capital budgeting, correlating the practical theoretical referential with the enterprise; (iv) to analyze the yield of the investment project, (v) to verify the influence of the financing, on the yield of the project; and, finally, (vi) to demonstrate the choice process among some alternatives of supply, when used as tools of aid to the purchase decision, the methods of the Internal Tax of Return and the Net Present Value. To the end of the study one concluded that the methods of the Internal Tax of Return and the Net Present Value are powerful tools in the yield evaluation and viability of investments projects. However, to only understand the methods through what they teach in books is not enough for the daily practical of capital budgeting. Literature starts from two basic points: (i) the investments analyst dominates all the countable revenues, expenditures, and investments concepts.(ii) the numerical examples are simple and easy to understand, to infer its practical applications is a contouring question to be raised and passed by the analyst. This study intends to show the conjunction of the bibliography with the practical one, therefore, from the instant that demonstrates the countable concept of the prescription, it also explains as it was constituted from the calculation of the demand, until its inclusion in the project. Thus, searching concepts of revenues, expenditures, depreciation and capital assets, disclosing its constitution and, over all, the application inside of the project, it all takes the analyst to the final part of the process, that consists in the determination of the numerical calculations, allowing to dedicate more time to the difficult task to interpret the data. Finally, understood the analysis of the economic viability of the project, the study guides the purchase of the equipment under the economic-financial point of view.

Valor prognóstico das cinéticas da procalcitonina e da proteína C reativa na pneumonia associada à ventilação mecânica

Introdução A pneumonia hospitalar é a principal causa de morte dentre as infecções hospitalares. A prevalência de pneumonia hospitalar em Unidades de Tratamento Intensivo (UTI) varia de 10 a 65%, com taxas de mortalidade que podem variar de 24 a 76%. A pneumonia associada à ventilação mecânica (PAV) é um determinante de mortalidade independente em pacientes submetidos à ventilação mecânica. A adequação do tratamento empírico precoce parece ser fundamental no prognóstico. Os critérios atualmente estabelecidos para avaliar adequação do tratamento empírico utilizam parâmetros clínicos, escores de gravidade e, principalmente, a sensibilidade do germe causador da infecção aos antibióticos administrados. Estes resultados balizam a necessidade de possíveis modificações no esquema antimicrobiano. A possibilidade de utilizar a Procalcitonina (PCT), a Proteína-C Reativa (CRP) e o escore SOFA (Avaliação de Falência de Órgãos Relacionada a Sepse), como indicadores de resposta do paciente, comparando seu status no dia do início do tratamento antimicrobiano (D0) com a evolução destes indicadores no quarto dia de tratamento (D4) abre a possibilidade de comparar o paciente com ele próprio, independente da exuberância da expressão da resposta inflamatória que ele possa desenvolver. Os resultados desta cinética entre D0 e D4 podem ser preditivos de gravidade de infecção, de eficiência antimicrobiana, e possivelmente de sobrevivência ou mortalidade hospitalar nos pacientes com suspeita de PAV. Objetivos Determinar e comparar o valor prognóstico de sobrevivência da cinética da PCT, da CRP, dos escores clínicos CPIS (Escore Clínico de Infecção Pulmonar) e SOFA, e do APACHE II (Avaliação da Fisiologia Aguda e da Saúde Crônica) na PAV entre o diagnóstico e o quarto dia de tratamento, quando a adequação do tratamento é avaliada. Pacientes e Métodos Realizamos um estudo de coorte prospectivo observacional que avaliou 75 pacientes internados no Centro de Tratamento Intensivo clínico-cirúrgico de adultos do Hospital de Clínicas de Porto Alegre que desenvolveram PAV no período de outubro de 2003 a agosto de 2005. Os pacientes com suspeita clínica de PAV que se adequaram aos critérios de inclusão e exclusão do estudo foram os candidatos a participar. Os familiares ou representantes dos pacientes receberam esclarecimentos por escrito acerca dos exames a serem realizados, bem como dos objetivos gerais da pesquisa. Os que aceitaram participar do estudo assinaram o termo de Consentimento Informado. O projeto foi aprovado pelo Comitê de Ética em Pesquisa do Hospital de Clínicas de Porto Alegre. No dia do diagnóstico de PAV foram coletados aspirado traqueal quantitativo, hemoculturas e sangue para a realização de dosagens de PCT, CRP, hemograma, plaquetas, creatinina, bilirrubinas, gasometria arterial e radiografia de tórax, com o objetivo de calcular o CPIS e o escore SOFA. No terceiro dia de tratamento foram novamente coletados aspirados traqueais quantitativos e os demais exames para o cálculo do CPIS. No quarto dia foi coletado sangue para dosagens de PCT, CRP e para os demais exames necessários para o cálculo do SOFA. Os pacientes foram acompanhados por 28 dias após o diagnóstico de PAV, quando foram considerados sobreviventes. Todos os pacientes que morreram antes do vigésimo oitavo dia foram considerados não-sobreviventes. Resultados Os níveis de PCT foram mais baixos nos sobreviventes em D0 (p=0.003) e em D4 (p=0.001). Os níveis de CRP não foram diferentes em sobreviventes e nãosobreviventes em D0 (p=0.77) e em D4 (p=0.14). O CPIS não pode diferenciar sobreviventes de não-sobrevientes em D0 (p=0.32) e em D3 (p=0.45). ΔCPIS decrescente não foi correlacionado a sobrevivência (p=0.59), o mesmo ocorrendo com CPIS <6 em D3 (p=0.79). Pacientes que morreram antes de D4 não puderam ter sua cinética calculada e foram considerados casos perdidos. Variáveis incluídas no modelo de regressão logística univariável para sobrevivência foram idade, APACHE II, ΔSOFA decrescente, ΔPCT decrescente e ΔCRP decrescente. Sobrevivência foi diretamente correlacionada a ΔPCT decrescente com RC = 5.67 (1.78;18.03) p = 0.003, ΔCRP com RC = 3.78 (1.24;11.50) p = 0.02, ΔSOFA decrescente com RC = 3.08 (1.02;9.26) p = 0.05 e escore APACHE II com RC = 0.92 (0.86;0.99) p = 0.02. O modelo de regressão logística multivariável para sobrevivência incluiu todas as variáveis participantes da análise univariável. Somente ΔPCT decrescente com RC = 4.43 (1.08;18.18) p = 0.04 e ΔCRP com RC = 7.40 (1.58;34.73) p = 0.01 permaneceram significativos. A avaliação da cinética dos marcadores inflamatórios e a associação com sobrevida no estudo mostraram que: - Em 95,1% dos sobreviventes houve queda dos níveis de PCT ou de CRP. - Em 61% dos sobreviventes ambos os níveis de PCT e de CRP caíram. Apenas 4,9% dos sobreviventes tiveram níveis de PCT e CRP crescentes. Com relação aos não-sobreviventes, 78.9% tiveram pelo menos um dos dois marcadores ou ambos com níveis crescentes. Conclusão As cinéticas da PCT e da CRP, obtidas pelas dosagens de seus níveis no dia do diagnóstico e no 4º dia de tratamento, podem predizer sobrevivência em pacientes com PAV. A queda dos níveis de pelo menos um destes marcadores ou de ambos indica maior chance de sobrevivência.

Rio como fomos: políticas culturais de 2001 a 2012

O presente trabalho pretende compreender os principais aspectos da gestão cultural implementada pela Secretaria Municipal de Cultura da cidade do Rio de Janeiro (SMC), no período de 2001 a 2012, refletindo sobre o papel do poder público na atualidade, através da análise de matérias de jornais e entrevistas com alguns dos principais atores envolvidos nesse processo. Concomitantemente, examinou-se o trabalho proposto pelos Secretários que comandaram a pasta nesse período, identificando as diretrizes de suas políticas culturais assim como seus principais projetos. Pretendeu-se compreender também, como as diretrizes e metas dos planejamentos estratégicos da Prefeitura (2004, 2009 e 2012) interferiram no tipo de política cultural estabelecida, e como essa política auxiliou na criação da representação da cidade que será sede de um megaevento como as Olimpíadas de 2016. Ao final, foram mostradas as semelhanças de discursos empregados pelos gestores da SMC, e entre seus projetos e escolhas.

Development, progress and economic growth

Progress was an idea of the 18th century; development, a project of the 20th century that continues into the 21st century. Progress was associated with the advance of reason, development with the fulfillment of the five political objectives that modern societies set for themselves: security, freedom, economic well-being, social justice and protection of the environment. Today we can view progress and development as equivalent. Both were products of the capitalist revolution, and of the economic development that began with it. Economic development or growth, in its turn, is the process of capital accumulation with the incorporation of technical progress that, mainly through productive sophistication and the increase of the value of labor, increases wages and improves standards of living. The five objectives that define development, as well as the three social instances existing in society change in an interdependent way.

The Panama canal expansion mega project : a case study and stakeholder´s analysis

As globalization increases integration, a new playing field is emerging which is driving the need for operational efficiencies and alignment of complementary capabilities among countries to build sustainable models and integrated offerings. As demands increase, companies are turning to effective project management as means to control operations and countries are increasing the amount of mega projects to boost their competitiveness and global footprint. Given the scale, complexity, political nature, multicultural makeup, and high level of visibility; mega projects rely on successful stakeholder management to effectively manage its operational, tactical, and strategic levels to execute their mission. This paper examines the success drivers of mega projects and presents an in depth stakeholder assessment of the Panama Canal Expansion mega project to identify the perceived value to its stakeholder community. The stakeholder categories include: the Panama Canal Authority, subcontractors executing the expansion project, customers of the canal in Panama and U.S., as well as the communities surrounding the Panama Canal and ports in the U.S. East Coast. The conclusion of this paper captures the relationship between the effective stakeholder engagement from the Panama Canal Authority, the perceived value of the Panamanian stakeholders, and compares it to U.S. based mega projects being executed simultaneously to allow the U.S. East Coast ports to accommodate increased cargo volumes.

Funding was obtained from a Capes Fellowship to NM, grants CNPq Universal 481351/ 2011-6, CNPq PQ 306604/2012-4, FAPERN/CNPq Pronem 003/2011, Capes SticAmSud, and FAPESP/CEPID/Neuromat to S.R. CNPq Universal 473554/2011-9 and 480053/ 2013-8, CNPq PQ 308558/2011-1, FACEPE/CNPq-PRONEX APQ- 0203-1.05/08, FACEPE/CNPq-PRONEM APQ-1415-1.05/10, and CNAIPS to M.C

Funding was obtained from a Capes Fellowship to NM, grants CNPq Universal 481351/ 2011-6, CNPq PQ 306604/2012-4, FAPERN/CNPq Pronem 003/2011, Capes SticAmSud, and FAPESP/CEPID/Neuromat to S.R. CNPq Universal 473554/2011-9 and 480053/ 2013-8, CNPq PQ 308558/2011-1, FACEPE/CNPq-PRONEX APQ- 0203-1.05/08, FACEPE/CNPq-PRONEM APQ-1415-1.05/10, and CNAIPS to M.C

Metodologia de análise e diagnóstico de fratura em um componente automotivo sujeito a cargas cíclicas alternadas

The competitiveness of the trade generated by the higher availability of products with lower quality and cost promoted a new reality of industrial production with small clearances. Track deviations at the production are not discarded, uncertainties can statistically occur. The world consumer and the Brazilian one are supported by the consumer protection code, in lawsuits against the products poor quality. An automobile is composed of various systems and thousands of constituent parts, increasing the likelihood of failure. The dynamic and security systems are critical in relation to the consequences of possible failures. The investigation of the failure gives us the possibility of learning and contributing to various improvements. Our main purpose in this work is to develop a systematic, specific methodology by investigating the root cause of the flaw occurred on an axle end of the front suspension of an automobile, and to perform comparative data analyses between the fractured part and the project information. Our research was based on a flaw generated in an automotive suspension system involved in a mechanical judicial cause, resulting in property and personal damages. In the investigations concerning the analysis of mechanical flaws, knowledge on materials engineering plays a crucial role in the process, since it enables applying techniques for characterizing materials, relating the technical attributes required from a respective part with its structure of manufacturing material, thus providing a greater scientific contribution to the work. The specific methodology developed follows its own flowchart. In the early phase, the data in the records and information on the involved ones were collected. The following laboratory analyses were performed: macrography of the fracture, micrography with SEM (Scanning Electron Microscope) of the initial and final fracture, phase analysis with optical microscopy, Brinell hardness and Vickers microhardness analyses, quantitative and qualitative chemical analysis, by using X-ray fluorescence and optical spectroscopy for carbon analysis, qualitative study on the state of tension was done. Field data were also collected. In the analyses data of the values resulting from the fractured stock parts and the design values were compared. After the investigation, one concluded that: the developed methodology systematized the investigation and enabled crossing data, thus minimizing diagnostic error probability, the morphology of the fracture indicates failure by the fatigue mechanism in a geometrically propitious location, a tension hub, the part was subjected to low tensions by the sectional area of the final fracture, the manufacturing material of the fractured part has low ductility, the component fractured in an earlier moment than the one recommended by the manufacturer, the percentages of C, Si, Mn and Cr of the fractured part present values which differ from the design ones, the hardness value of the superior limit of the fractured part is higher than that of the design, and there is no manufacturing uniformity between stock and fractured part. The work will contribute to optimizing the guidance of the actions in a mechanical engineering judicial expertise

Secagem do resíduo de acerola (Malphigia emarginata D.C.): estudo do processo e avaliação do impacto sobre o produto final

Brazil, one of the largest agricultural producers in the world, has managed in recent years to significantly improve its production. However, in response to this advance in the agro-industrial sector, the generation of agro-industrial residues has also increased. New technological alternatives have to be implemented in order to bring economic and rational use of this material and drying is one of the possible choices. Considering the great importance that bioactive compounds present for food science and technology, this research aims to evaluate the air-drying process of acerola residue in a tray convective drier under controlled temperature (60, 70 e 80ºC), air velocity (4.0, 5.0 e 6.0 m/s) and material width (0.5, 0.62 e 0.75 cm) by applying an experimental planning 23 + 3. Based on that, the impact on physical-chemical characteristics, color, bioactive compounds concentration and antioxidant activity of dried acerola waste was evaluated, having the in natura and freeze dried waste as control groups. Dried acerola residue presented natural pigments, mainly carotenoids (143.68 - 68.29 mg/g) and anthocyanins (290.92 - 90.11 mg/100 g), which explain the red and yellow instrumental color parameters observed. The acerola residue powder is also rich in phenolic compounds (3261.11 -2692.60 mgGAEeq/100g), proanthocyanidins (61.33-58.46 eq/100g), ascorbic acid (389.44 739.29 mg/100 g) and DPPH antioxidant activity (20.91 24.72 μg Trolox eq/g). Results show decreased concentration of phenolic compounds, anthocyanins, carotenoids, proanthocyanidins and ascorbic acid caused by the air-drying process. However, even after the observed drying losses, the acerola residue powder can be considered a high value food ingredient, considering the high bioactive compounds concentration found in the final product, as well as the colorimetric characterization and microbiological stability of the dried powder

Detection of glucose and triglycerides using information visualization methods to process impedance spectroscopy data

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Theoretical analysis of the energy levels induced by oxygen vacancies and the doping process (Co, Cu and Zn) on SnO2 (110) surface models

Density functional calculation at B3LYP level was employed to study the surface oxygen vacancies and the doping process of Co, Cu and Zn on SnO2 (110) surface models. Large clusters, based on (SnO2)(15) models, were selected to simulate the oxidized (Sn15O30), half-reduced (Sn15O29) and the reduced (Sn15O28) surfaces. The doping process was considered on the reduced surfaces: Sn13Co2O28, Sn13Cu2O28 and Sn13Zn2O28. The results are analyzed and discussed based on a calculation of the energy levels along the bulk band gap region, determined by a projection of the monoelectron level structure on to the atomic basis set and by the density of states. This procedure enables one to distinguish the states coming from the bulk, the oxygen vacancies and the doping process, on passing from an oxidized to a reduced surface, missing bridge oxygen atoms generate electronic levels along the band gap region, associated with 5s/5p of four-/five-fold Sn and 2p of in-plane O centers located on the exposed surface, which is in agreement with previous theoretical and experimental investigations. The formation energy of one and two oxygen vacancies is 3.0 and 3.9 eV, respectively. (C) 2001 Elsevier B.V. B.V. All rights reserved.

In-process grinding monitoring by acoustic emission

This work aims to investigate the efficiency of digital signal processing tools of acoustic emission signals in order to detect thermal damages in grinding process. To accomplish such a goal, an experimental work was carried out for 15 runs in a surface grinding machine operating with an aluminum oxide grinding wheel and ABNT 1045. The acoustic emission signals were acquired from a fixed sensor placed on the workpiece holder. A high sampling rate data acquisition system at 2.5 MHz was used to collect the raw acoustic emission instead of root mean square value usually employed. Many statistics have shown effective to detect burn, such as the root mean square (RMS), correlation of the AE, constant false alarm (CFAR), ratio of power (ROP) and mean-value deviance (MVD). However, the CFAR, ROP, Kurtosis and correlation of the AE have been presented more sensitive than the RMS.