Influence of EfOM on the oxidation of micropollutants by Ozone and UV/H2O2 in secondary effluents

The aim of this work was to study the influence of effluent organic matter (EfOM) on micropollutants removal by ozone and UV/H2O2. To perform the experiments, deionized water and municipal secondary effluents (SE) were artificially contaminated with atrazine (ATZ) and treated by the two proposed methods. ATZ concentration, COD and TOC were recorded along the reaction time and used to evaluate EfOM effect on the system efficiency. Results demonstrate that the presence of EfOM can significantly reduce the micropollutant removal rate due to competition of EfOM components to react with radicals and/or molecular ozone. The hydroxyl radical scavenging caused by EfOM was quantified as well as the contribution of molecular ozone and �OH radicals during the ozonation of SE. EfOM components promoted higher inhibition of ATZ oxidation by hydroxyl radicals than by molecular ozone.

A Quantitative method for the characterization of lytic metastases of the bone from radiographic images

The aim of our study was to assess the diagnostic usefulness of the gray level parameters to distinguish osteolytic lesions using radiological images. Materials and Methods: A retrospective study was carried out. A total of 76 skeletal radiographs of osteolytic metastases and 67 radiographs of multiple myeloma were used. The cases were classified into nonflat (MM1 and OL1) and flat bones (MM2 and OL2). These radiological images were analyzed by using a computerized method. The parameters calculated were mean, standard deviation, and coefficient of variation (MGL, SDGL, and CVGL) based on gray level histogram analysis of a region-of-interest.Diagnostic utility was quantified bymeasurement of parameters on osteolyticmetastases andmultiplemyeloma, yielding quantification of area under the receiver operating characteristic (ROC) curve (AUC). Results: Flat bone groups (MM2 and OL2) showed significant differences in mean values of MGL ( = 0.048) and SDGL ( = 0.003). Their corresponding values of AUC were 0.758 for MGL and 0.883 for SDGL in flat bones. In nonflat bones these gray level parameters do not show diagnostic ability. Conclusion: The gray level parametersMGL and SDGL show a good discriminatory diagnostic ability to distinguish between multiple myeloma and lytic metastases in flat bones.

The use of mixed methods research in the behavioral sciences field

Mixed methods research involves the combined use of quantitative and qualitative methods in the same research study, and it is becoming increasingly important in several scientific areas. The aim of this paper is to review and compare through a mixed methods multiple-case study the application of this methodology in three reputable behavioural science journals: the Journal of Organizational Behavior, Addictive Behaviors and Psicothema. A quantitative analysis was carried out to review all the papers published in these journals during the period 2003-2008 and classify them into two blocks: theoretical and empirical, with the latter being further subdivided into three subtypes (quantitative, qualitative and mixed). A qualitative analysis determined the main characteristics of the mixed methods studies identified, in order to describe in more detail the ways in which the two methods are combined based on their purpose, priority, implementation and research design. From the journals selected, a total of 1.958 articles were analysed, the majority of which corresponded to empirical studies, with only a small number referring to research that used mixed methods. Nonetheless, mixed methods research does appear in all the behavioural science journals studied within the period selected, showing a range of designs, where the sequential equal weight mixed methods research design seems to stand out.

The process of basic training, applied training, maintaining the performance of an observer

In the field of observational methodology the observer is obviously a central figure, and close attention should be paid to the process through which he or she acquires, applies, and maintains the skills required. Basic training in how to apply the operational definitions of categories and the rules for coding, coupled with the opportunity to use the observation instrument in real-life situations, can have a positive effect in terms of the degree of agreement achieved when one evaluates intra- and inter-observer reliability. Several authors, including Arias, Argudo, & Alonso (2009) and Medina and Delgado (1999), have put forward proposals for the process of basic and applied training in this context. Reid y De Master (1982) focuses on the observer's performance and how to maintain the acquired skills, it being argued that periodic checks are needed after initial training because an observer may, over time, become less reliable due to the inherent complexity of category systems. The purpose of this subsequent training is to maintain acceptable levels of observer reliability. Various strategies can be used to this end, including providing feedback about those categories associated with a good reliability index, or offering re-training in how to apply those that yield lower indices. The aim of this study is to develop a performance-based index that is capable of assessing an observer's ability to produce reliable observations in conjunction with other observers.

Brain Dopamine and Serotonin Receptors in the Perception of Pain. Positron Emission Tomography Studies in Healthy Subjects

The role of dopamine and serotonin in spinal pain regulation is well established. However, little is known concerning the role of brain dopamine and serotonin in the perception of pain in humans. The aim of this study was to assess the potential role of brain dopamine and serotonin in determining experimental pain sensitivity in humans using positron emission tomography (PET) and psychophysical methods. A total of 39 healthy subjects participated in the study, and PET imaging was performed to assess brain dopamine D2/D3 and serotonin 5-HT_1A receptor availability. In a separate session, sensitivity to pain and touch was assessed with traditional psychophysical methods, allowing the evaluation of potential associations between D2/D3 and 5-HT_1A binding and psychophysical responses. The subjects’ responses were also analyzed according to Signal Detection Theory, which enables separate assessment of the subject’s discriminative capacity (sensory factor) and response criterion (non-sensory factor). The study found that the D2/D3 receptor binding in the right putamen was inversely correlated with pain threshold and response criterion. 5-HT_1A binding in cingulate cortex, inferior temporal gyrus and medial prefrontal cortex was inversely correlated with discriminative capacity for touch. Additionally, the response criterion for pain and intensity rating of suprathreshold pain were inversely correlated with 5-HT_1A binding in multiple brain areas. The results suggest that brain D2/D3 receptors and 5-HT_1A receptors modulate sensitivity to pain and that the pain modulatory effects may, at least partly, be attributed to influences on the response criterion. 5-HT_1A receptors are also involved in the regulation of touch by having an effect on discriminative capacity.

The Methods of Possible Joint Treatment of Manure and Sewage Sludge in the Leningrad Region

The nutrient load to the Gulf of Finland has started to increase as a result of the strong economic recovery in agriculture and livestock farming in the Leningrad region. Also sludge produced from municipal wastewater treatment plant of the Leningrad region causes the great impact on the environment, but still the main options for its treatment is disposal on the sludge beds or Landfills. The aim of this study was to evaluate the implementation of possible joint treatment methods of manure form livestock and poultry enterprises and sewage sludge produced from municipal wastewater treatment plants in the Leningrad region. The study is based on published data. The most attention was put on the anaerobic digestion and incineration methods. The manure and sewage sludge generation for the whole Leningrad region and energy potential produced from their treatment were estimated. The calculations showed that total amount of sewage sludge generation is 1 348 000 t/a calculated on wet matter and manure generation is 3 445 000 t/a calculated on wet matter. The potential heat release from anaerobic digestion process and incineration process is 4 880 000 GJ/a and 5 950 000 GJ/a, respectively. Furthermore, the work gives the overview of the general Russian and Finnish legislation concerning manure and sewage sludge treatment. In the Gatchina district it was chosen the WWTP and livestock and poultry enterprises for evaluation of the centralized treatment plant implementation based on anaerobic digestion and incineration methods. The electricity and heat power of plant based on biogas combustion process is 4.3 MW and 7.8 MW, respectively. The electricity and heat power of plant based on manure and sewage sludge incineration process is 3.0 MW and 6.1 MW, respectively.

Nursing Ethics Education in Finland from the Perspective of Codes of Ethics

The purpose of this study was to analyze nursing ethics education from the perspective of nurses’ codes of ethics in the basic nursing education programmes in polytechnics in Finland with the following research questions: What is known about nurses’ codes in practice and education, what contents of the codes are taught, what teaching and evaluation methods are used, which demographic variables are associated with the teaching, what is nurse educators’ adequacy of knowledge to teach the codes and nursing students’ knowledge of and ability to apply the codes, and what are participants’ opinions of the need and applicability of the codes, and their importance in nursing ethics education. The aim of the study was to identify strengths and possible problem areas in teaching of the codes and nursing ethics in general. The knowledge gained from this study can be used for developing nursing ethics curricula and teaching of ethics in theory and practice. The data collection was targeted to all polytechnics in Finland providing basic nursing education (i.e. Bachelor of Health Care). The target groups were all nurse educators teaching ethics and all graduating nursing students in the academic year of 2006. A total of 183 educators and 214 students from 24 polytechnics participated. The data was collected using a structured questionnaire with four open-ended questions, designed for this study. The data was analysed by SPSS (14.0) and the open-ended questions by inductive content analysis. Descriptive statistics were used to summarize the data. Inferential statistics were used to estimate the differences between the participant groups. The reliability of the questionnaire was estimated with Cronbach’s coefficient alpha. The literature review revealed that empirical research on the codes was scarce, and minimal in the area of education. Teaching of nurses’ codes themselves and the embedded ethical concepts was extensive, teaching of the functions of the codes and related laws and agreements was moderate, but teaching of the codes of other health care professions was modest. Issues related to the nurse-patient relationship were emphasised. Wider social dimensions of the codes were less emphasized. Educators’ and students’ descriptions of teaching emphasized mainly the same teaching contents, but there were statistically significant differences between the groups in that educators assessed their teaching to be more extensive than what students had perceived it had been. T he use of teaching and evaluation methods was rather narrow and conventional. However, educators’ and students’ descriptions of the used methods differed statistically significantly. Students’ knowledge of the codes and their ability to apply them in practice was assessed as mediocre by educators and by students themselves. Most educators assessed their own knowledge of the codes as adequate to teach the codes, as did most of the students. Educators who regarded their knowledge as adequate taught the codes more extensively than those who assessed their knowledge as less adequate. Also students who assessed their educators’ knowledge as adequate perceived the teaching of the codes to be more extensive. Otherwise educators’ and students’ demographic variables had little association with their descriptions of the teaching. According to the participants, nurses need their own codes, and they are also regarded as applicable in practice. The codes are an important element in nursing ethics education, but their teaching needs development. Further research should focus on the organization of ethics teaching in the curricula, the teaching process, and on the evaluation of the effectiveness of ethics education and on educators’ competence. Also the meaning and functions of the codes at all levels of nursing deserve attention. More versatile use of research methods would be beneficial in gaining new knowledge.

The concept of solution: Industry’s insights compared to theoretical views

Many manufacturing companies have started to offer complete solutions to their customers’ unique needs due to toughening competition and customer demand. Discourse on this kind of solution business is still developing, hence, there is not an established definition for the concept of solution. The aim of the study is to profoundly identify the concept of solution and to understand how the industry’s current views differ from the theoretical concepts. The describing dimensions are identified from selected 13 theoretical notions, and from responses, that the employees of five different companies have given. The 32 interview transcripts are analyzed with thematic analysis and qualitative content analysis. According to the findings, the concept of solution is characterized by integration, customization, risk-sharing, value co-creation, long-term orientation, and desired outcomes. The industry’s insights differ in terms of them all. The results illustrate, that a solution is a bundle, and the whole solution is customized on some level for a client. A solution supplier needs to be customer-focused, in which value co-creation is only a part. The solution solves the customer’s problem, and improves both the customer’s, and the supplier’s business. Neither long-term focus nor risks-sharing were directly employed to characterize the concept of solution. Differences are mainly due to the different approaches to the definitions and inexperience of the companies.

The Influence of Certain Processing Factors on the Durability of Yttrium Stabilized Zirconia Used As Dental Biomaterial

In dentistry, yttrium partially stabilized zirconia (ZrO2) has become one of the most attractive ceramic materials for prosthetic applications. The aim of this series of studies was to evaluate whether certain treatments used in the manufacturing process, such as sintering time, color shading or heat treatment of zirconia affect the material properties. Another aim was to evaluate the load-bearing capacity and marginal fit of manually copy-milled custom-made versus prefabricated commercially available zirconia implant abutments. Mechanical properties such as flexural strength and surface microhardness were determined for green-stage milled and sintered yttrium partially stabilized zirconia after different sintering time, coloring process and heat treatments. Scanning electron microscope (SEM) was used for analyzing the possible changes in surface structure of zirconia material after reduced sintering time, coloring and heat treatments. Possible phase change from the tetragonal to the monoclinic phase was evaluated by X-ray diffraction analysis (XRD). The load-bearing capacity of different implant abutments was measured and the fit between abutment and implant replica was examined with SEM. The results of these studies showed that the shorter sintering time or the thermocycling did not affect the strength or surface microhardness of zirconia. Coloring of zirconia decreased strength compared to un-colored control zirconia, and some of the colored zirconia specimens also showed a decrease in surface microhardness. Coloring also affected the dimensions of zirconia. Significantly decreased shrinkage was found for colored zirconia specimens during sintering. Heat treatment of zirconia did not seem to affect materials’ mechanical properties but when a thin coating of wash and glaze porcelain was fired on the tensile side of the disc the flexural strength decreased significantly. Furthermore, it was found that thermocycling increased the monoclinic phase on the surface of the zirconia. Color shading or heat treatment did not seem to affect phase transformation but small monoclinic peaks were detected on the surface of the heat treated specimens with a thin coating of wash and glaze porcelain on the opposite side. Custom-made zirconia abutments showed comparable load-bearing capacity to the prefabricated commercially available zirconia abutments. However, the fit of the custom-made abutments was less satisfactory than that of the commercially available abutments. These studies suggest that zirconia is a durable material and other treatments than color shading used in the manufacturing process of zirconia bulk material does not affect the material’s strength. The decrease in strength and dimensional changes after color shading needs to be taken into account when fabricating zirconia substructures for fixed dental prostheses. Manually copy-milled custom-made abutments have acceptable load-bearing capacity but the marginal accuracy has to be evaluated carefully.

BRUNO BAUCH AND THE COMPREHENSIBILITY OF NATURE

ABSTRACT The aim of this paper is to discuss how Bruno Bauch deals with the problem of the coordination between empirical concepts and spatiotemporal objects. We shall argue that Bauch reformulates the Kantian distinction between concepts and intuitions by means of a philosophical consideration of differential calculus and that he thereby explains the possibility of such coordination, avoiding certain difficulties of the Kantian doctrine.

Considering Target Groups in the Creation of a Comprehensive City Branding Process

The aim of the research was to create a comprehensive city branding process. This was done by identifying the key target groups of the city and considering them in the city branding process. Also key stakeholders were identified and taken into consideration when creating the branding process. As an empirical study, three first stages of the city branding process were implemented for the city of Lappeenranta having "students" as the case target group. An interview with the city officials was conducted, as well as a student survey on the current city image of Lappeenranta. Quantitative research methods were used to analyze the results of the survey. A comprehensive city branding process with eight stages was created in the research. Target groups were considered in the process by identifying the target group dependent stages. The empirical study revealed that the current city image held by the students consists of six dimensions. These dimensions were analyzed from the viewpoint of Lappeenranta with the help of an importance performance analysis.

Berry polyphenol absorption and the effect of northern berries on metabolism, ectopic fat accumulation, and associated diseases

The prevalence of obesity and type 2 diabetes has increased at an alarming rate in developed countries. It seems in the light of current knowledge that metabolic syndrome may not develop at all without NAFLD, and NAFLD is estimated to be as common as metabolic syndrome in western population (23 % occurrence). Fat in the liver is called ectopic fat, which is triacylglycerols within the cells of non-adipose tissue. Serum alanine aminotransferase (ALT) values correlate positively with liver fat proportions, and increased activity of ALT predicts type 2 diabetes independently from obesity. Berries, high in natural bioactive compounds, have indicated the potential to reduce the risk of obesity-related diseases. Ectopic fat induces common endocrine excretion of adipose tissue resulting in the overproduction of inflammatory markers, which further induce insulin resistance by multiple mechanisms. Insulin resistance inducing hyperinsulinemia and lipolysis in adipocytes increases the concentration of free fatty acids and consequently causes further fat accumulation in hepatocytes. Polyphenolic fractions of berries have been shown to reverse inflammatory reaction cascades in in vitro and animal studies, and moreover to decrease ectopic fat accumulation. The aim of this thesis was to explore the role of northern berries in obesity-related diseases. The absorption and metabolism of selected berry polyphenols, flavonol glycosides and anthocyanins, was investigated in humans, and metabolites of the studied compounds were identified in plasma and urine samples (I, II). Further, the effects of berries on the risk factors of metabolic syndrome were studied in clinical intervention trials (III, IV), and the different fractions of sea buckthorn berry were tested for their ability to reduce postprandial glycemia and insulinemia after high-glucose meal in a postprandial study with humans (V). The marked impact of mixed berries on plasma ALT values (III), as well as indications of the positive effects of sea buckthorn, its fractions and bilberry on omental adiposity and adhesion molecules (IV) were observed. In study V, sea buckthorn and its polyphenol fractions had a promising effect on potprandial metabolism after high-glucose meal. In the literature review, the possible mechanisms behind the observed effects have been discussed with a special emphasis on ectopic fat accumulation. The literature review indicated that especially tannins and flavonoids have shown potential in suppressing diverse reaction cascades related to systemic inflammation, ectopic fat accumulation and insulin resistance development.

The Use of Radiostereometric Analysis in Fractures of the Distal Radius: From Phantom Models to Clinical Application

Radiostereometric analysis (RSA) is a highly accurate method for the measurement of in vivo micromotion of orthopaedic implants. Validation of the RSA method is a prerequisite for performing clinical RSA studies. Only a limited number of studies have utilised the RSA method in the evaluation of migration and inducible micromotion during fracture healing. Volar plate fixation of distal radial fractures has increased in popularity. There is still very little prospective randomised evidence supporting the use of these implants over other treatments. The aim of this study was to investigate the precision, accuracy, and feasibility of using RSA in the evaluation of healing in distal radius fractures treated with a volar fixed-angle plate. A physical phantom model was used to validate the RSA method for simple distal radius fractures. A computer simulation model was then used to validate the RSA method for more complex interfragmentary motion in intra-articular fractures. A separate pre-clinical investigation was performed in order to evaluate the possibility of using novel resorbable markers for RSA. Based on the validation studies, a prospective RSA cohort study of fifteen patients with plated AO type-C distal radius fractures with a 1-year follow-up was performed. RSA was shown to be highly accurate and precise in the measurement of fracture micromotion using both physical and computer simulated models of distal radius fractures. Resorbable RSA markers demonstrated potential for use in RSA. The RSA method was found to have a high clinical precision. The fractures underwent significant translational and rotational migration during the first two weeks after surgery, but not thereafter. Maximal grip caused significant translational and rotational interfragmentary micromotion. This inducible micromotion was detectable up to eighteen weeks, even after the achievement of radiographic union. The application of RSA in the measurement of fracture fragment migration and inducible interfragmentary micromotion in AO type-C distal radius fractures is feasible but technically demanding. RSA may be a unique tool in defining the progress of fracture union.

Dialogue in the crisis of representation : realism and antirealism in the context of the conversation between theologians and quantum physicists in Göttingen 1949-1961

The aim of this study is to analyse the content of the interdisciplinary conversations in Göttingen between 1949 and 1961. The task is to compare models for describing reality presented by quantum physicists and theologians. Descriptions of reality indifferent disciplines are conditioned by the development of the concept of reality in philosophy, physics and theology. Our basic problem is stated in the question: How is it possible for the intramental image to match the external object?Cartesian knowledge presupposes clear and distinct ideas in the mind prior to observation resulting in a true correspondence between the observed object and the cogitative observing subject. The Kantian synthesis between rationalism and empiricism emphasises an extended character of representation. The human mind is not a passive receiver of external information, but is actively construing intramental representations of external reality in the epistemological process. Heidegger's aim was to reach a more primordial mode of understanding reality than what is possible in the Cartesian Subject-Object distinction. In Heidegger's philosophy, ontology as being-in-the-world is prior to knowledge concerning being. Ontology can be grasped only in the totality of being (Dasein), not only as an object of reflection and perception. According to Bohr, quantum mechanics introduces an irreducible loss in representation, which classically understood is a deficiency in knowledge. The conflicting aspects (particle and wave pictures) in our comprehension of physical reality, cannot be completely accommodated into an entire and coherent model of reality. What Bohr rejects is not realism, but the classical Einsteinian version of it. By the use of complementary descriptions, Bohr tries to save a fundamentally realistic position. The fundamental question in Barthian theology is the problem of God as an object of theological discourse. Dialectics is Barth¿s way to express knowledge of God avoiding a speculative theology and a human-centred religious self-consciousness. In Barthian theology, the human capacity for knowledge, independently of revelation, is insufficient to comprehend the being of God. Our knowledge of God is real knowledge in revelation and our words are made to correspond with the divine reality in an analogy of faith. The point of the Bultmannian demythologising programme was to claim the real existence of God beyond our faculties. We cannot simply define God as a human ideal of existence or a focus of values. The theological programme of Bultmann emphasised the notion that we can talk meaningfully of God only insofar as we have existential experience of his intervention. Common to all these twentieth century philosophical, physical and theological positions, is a form of anti-Cartesianism. Consequently, in regard to their epistemology, they can be labelled antirealist. This common insight also made it possible to find a common meeting point between the different disciplines. In this study, the different standpoints from all three areas and the conversations in Göttingen are analysed in the frameworkof realism/antirealism. One of the first tasks in the Göttingen conversations was to analyse the nature of the likeness between the complementary structures inquantum physics introduced by Niels Bohr and the dialectical forms in the Barthian doctrine of God. The reaction against epistemological Cartesianism, metaphysics of substance and deterministic description of reality was the common point of departure for theologians and physicists in the Göttingen discussions. In his complementarity, Bohr anticipated the crossing of traditional epistemic boundaries and the generalisation of epistemological strategies by introducing interpretative procedures across various disciplines.

Development of research networks : the case of social capital

The aim of this study is to explore how a new concept appears inscientific discussion and research, how it diffuses to other fields and out of the scientific communities, and how the networks are formed around the concept. Text and terminology take the interest of a reader in the digital environment. Texts create networks where the terminology used is dependent on the ideas, viewsand paradigms of the field. This study is based mainly on bibliographic data. Materials for bibliometric studies have been collected from different databases. The databases are also evaluated and their quality and coverage are discussed. The thesauri of those databases that have been selected for a more in depth study have also been evaluated. The material selected has been used to study how long and in which ways an innovative publication, which can be seen as a milestone in a specific field, influences the research. The concept that has been chosen as a topic for this research is Social Capital, because it has been a popular concept in different scientific fields as well as in everyday speech and the media. It seemed to be a `fashion concept´ that appeared in different situations at the Millennium. The growth and diffusion of social capital publications has been studied. The terms connected with social capital in different fields and different stages of the development have also been analyzed. The methods that have been used in this study are growth and diffusion analysis, content analysis, citation analysis, coword analysis and cocitation analysis. One method that can be used tounderstand and to interpret results of these bibliometric studies is to interview some key persons, who are known to have a gatekeeper position in the diffusion of the concept. Thematic interviews with some Finnish researchers and specialists that have influenced the diffusion of social capital into Finnish scientificand social discussions provide background information. iv The Milestone Publications on social capital have been chosen and studied. They give answers to the question "What is Social Capital?" By comparing citations to Milestone Publications with the growth of all social capital publications in a database, we can drawconclusions about the point at which social capital became generally approved `tacit knowledge´. The contribution of the present study lies foremost in understanding the development of network structures around a new concept that has diffused in scientific communities and also outside them. The network means both networks of researchers, networks of publications and networks of concepts that describe the research field. The emphasis has been on the digital environment and onthe socalled information society that we are now living in, but in this transitional stage, the printed publications are still important and widely used in social sciences and humanities. The network formation is affected by social relations and informal contacts that push new ideas. This study also gives new information about using different research methods, like bibliometric methods supported by interviews and content analyses. It is evident that interpretation of bibliometric maps presupposes qualitative information and understanding of the phenomena under study.