Elektrorheologie homogener Systeme

Zusammenfassung: Thema dieser Arbeit ist der Einfluss von elektrischen Feldern auf die Viskosität nematischer Flüssigkristalle sowie isotroper Polymerlösungen.Für zwei thermotrope nematische Flüssigkristalle, 4-(trans-4'-n-Pentylcyclohexyl)-benzonitril (PCH-5) und 4-n-Pentyl-4'-cyanobiphenyl (5CB), wurde die Viskosität mit elektrorheologischen Messungen in Abhängigkeit von Feldstärke und Scherrate bestimmt. Alle Messwerte kommen bei Auftragung gegen E?/? auf einer Masterkurve zu liegen. Die Anpassung dieser Daten mit einer auf der Theorie von Ericksen und Leslie basierenden Gleichung liefert gleichzeitig die Scherviskositäten ? und ? sowie die Rotationsviskosität ? in guter Übereinstimmung mit Literaturwerten. Elektrorheologische Messungen stellen somit eine Methode zur Bestimmung dieser Viskositätskoeffizienten für Nematen dar, wenn diese eine ausreichend große positive dielektrische Anisotropie aufweisen. Bei den isotropen Polymerlösungen ließ sich der elektrorheologische Effekt des Systems Decalin/Polystyrol im Bereich der Entmischungstemperatur klären. Während im Ein-Phasen-Gebiet nur eine geringe Viskositätsänderung im E-Feld aufgrund elektrohydrodynamischer Strömungen zu beobachten ist, tritt unterhalb der Entmischungstemperatur ein deutlicher, aber nicht reproduzierbarer ER-Effekt auf. Dieser ist auf einen Einfluss des E-Felds auf die Zwei-Phasen-Morphologie zurückzuführen.Für das System Diethylbenzol/Isopentylcellulose wurde ein negativer elektrorheologischer Effekt auf die Dissoziation von assoziierten Polymermolekülen zurückgeführt. Die Dissoziation erfolgt aufgrund der Wirkung des elektrischen Feldes auf freie Ladungen.

Strukturfaktoren, Modenkopplungsgleichungen und Glasübergang molekularer Kristalle

In dieser Arbeit wird der Orientierungsglasübergang ungeordneter, molekularer Kristalle untersucht. Die theoretische Behandlung ist durch die Anisotropie der Einteilchen-Verteilungsfunktion und der Paarfunktionen erschwert. Nimmt man ein starres Gitter, wird der reziproke Raum im Gegenzug auf die 1. Brillouin-Zone eingeschränkt. Der Orientierungsglasübergang wird im Rahmen der Modenkopplungsgleichungen studiert, die dazu hergeleitet werden. Als Modell dienen harte Rotationsellipsoide auf einem starren sc Gitter. Zur Berechnung der statischen tensoriellen Strukturfaktoren wird die Ornstein-Zernike(OZ)-Gleichung molekularer Kristalle abgeleitet und selbstkonsistent zusammen mit der von molekularen Flüssigkeiten übernommenen Percus-Yevick(PY)-Näherung gelöst. Parallel dazu werden die Strukturfaktoren durch MC-Simulationen ermittelt. Die OZ-Gleichung molekularer Kristalle ähnelt der von Flüssigkeiten, direkte und totale Korrelationsfunktion kommen jedoch wegen des starren Gitters nur ohne Konstantanteile in den Winkelvariablen vor, im Gegensatz zur PY-Näherung. Die Anisotropie bringt außerdem einen nichttrivialen Zusatzfaktor. OZ/PY-Strukturfaktoren und MC-Ergebnisse stimmen gut überein. Bei den Matrixelementen der Dichte-Dichte-Korrelationsfunktion gibt es drei Hauptverläufe: oszillatorisch, monoton und unregelmäßig abfallend. Oszillationen gehören zu alternierenden Dichtefluktuationen, führen zu Maxima der Strukturfaktoren am Zonenrand und kommen bei oblaten und genügend breiten prolaten, schwächer auch bei dünnen, nicht zu langen prolaten Ellipsoiden vor. Der exponentielle monotone Abfall kommt bei allen Ellipsoiden vor und führt zu Maxima der Strukturfaktoren in der Zonenmitte, was die Tendenz zu nematischer Ordnung zeigt. Die OZ/PY-Theorie ist durch divergierende Maxima der Strukturfaktoren begrenzt. Bei den Modenkopplungsgleichungen molekularer Kristalle zeigt sich eine große Ähnlichkeit mit denen molekularer Flüssigkeiten, jedoch spielen auf einem starrem Gitter nur die Matrixelemente mit l,l' > 0 eine Rolle und es finden Umklapps von reziproken Vektoren statt. Die Anisotropie bringt auch hier nichtkonstante Zusatzfaktoren ins Spiel. Bis auf flache oblate Ellipsoide wird die Modenkopplungs-Glaslinie von der Divergenz der Strukturfaktoren bestimmt. Für sehr lange Ellipsoide müssen die Strukturfaktoren zur Divergenz hin extrapoliert werden. Daher treibt nicht der Orientierungskäfigeffekt den Glasübergang, sondern Fluktuationen an einer Phasengrenze. Nahe der Kugelform ist keine zuverlässige Glasline festlegbar. Die eingefrorenen kritischen Dichte-Dichte-Korrelatoren haben nur in wenigen Fällen die Oszillationen der statischen Korrelatoren. Der monotone Abfall bleibt dagegen für lange Zeiten meist erhalten. Folglich haben die kritischen Modenkopplungs-Nichtergodizitätsparameter abgeschwächte Maxima in der Zonenmitte, während die Maxima am Zonenrand meist verschwunden sind. Die normierten Nichtergodizitätsparameter zeigen eine Fülle von Verläufen, besonders tiefer im Glas.

Rod-coil copolymer structures

Skalenargumente werden verwendet, um Rod-Coil Copolymere mit fester Zusammensetzung von steifen Stäbchen und flexiblen Ketten zu studieren. In einem selektiven Lösungsmittel, in dem sich nur die Ketten lösen, bildet ein Rod-Coil Multiblock zylinderförmige Micellen aus aggregierten Stäbchen verbunden durch Kettenstücke. Die Stäbchen aggregieren, um Energie zu gewinnen. Dieser Prozeß wird durch den Entropieverlust der flexiblen Ketten ausgeglichen. Das Adsorptionsverhalten von Aggregaten aus parallel aneinandergelagerten, einzelnen Rod-Coil Diblöcken in selektivem Lösungsmittel wird anhand von erweiterten Skalenbetrachtungen diskutiert. Wenn ein solches Aggregat mit den Stäbchen parallel zur Oberfläche adsorbiert, verschieben sich die Stäbchen gegeneinander. Zusätzlich werden die Stabilität der adsorbierten Aggregate und andere mögliche Konfigurationen untersucht. Um einen Rod-Coil Multiblock mit variabler Zusammensetzung zu studieren, wird eine Feldtheorie entwickelt. Jedes Segment kann entweder steif oder flexibel sein. Das System zeigt drei Phasenzustände, offene Kette, amorphe Globule und flüssig-kristalline Globule. Beim Übergang von amorpher zu flüssig-kristalliner Globule steigt der Anteil an steifen Segmenten rapide an. Dieser Übergang wird durch die isotrope Wechselwirkung zwischen den steifen Segmenten und die anisotrope Oberflächenenergie der Globule verursacht.

Anisotrope Kolloide aus flüssigkristallinen Polymeren

In dieser Arbeit wird die Synthese, Charakterisierung und Manipulation anisotroper Kolloide aus flüssigkristallinen Polymeren beschrieben. Um Kolloide verschiedener Größe und aus verschiedenen Polymeren zu erhalten, wurden verschiedene Techniken verwendet. Einerseits wurden Kolloide aus nematischen und smektischen Polymeren mit Durchmessern meist im Bereich von 0,5 bis 3,5 Mikrometern hergestellt. Dazu wurden 16 verschiedene Acrylat- und Methacrylatmonomere synthetisiert und mittels Dispersionspolymerisation polymerisiert. Durch Variation der Polymerisationsbedingungen wurden Kolloide verschiedener Größe und Polydispersität erhalten. Durch Saatpolymerisation konnten zudem die Kugelgrößen bei gleichbleibend geringer Polydispersität erhöht werden. Polarisationsmikroskopie zeigt, dass die meisten Kolloide mit einer Größe zwischen ca. 2 bis 4 Mikrometern eine bipolare Direktorkonfiguration haben. Einige dieser Kolloide wurden mit einer optischen Pinzette mit zirkular polarisiertem Licht eingefangen und rotiert. Zum anderen wurden verschiedene flüssigkristalline Polymere (Polysiloxane, Hauptkettenpolymere und Polyacrylate) durch den Miniemulsionsprozess in Kolloide mit Durchmessern im Bereich von ca. 50 bis 300 nm überführt. Durch Variation der Emulgator- und Polymermenge sowie der Art des Emulgators konnte die Kugelgröße beeinflusst werden. Für die Polysiloxankolloide erfolgte die Aufklärung ihrer inneren Struktur mittels TEM und Kryo-TEM, da durch das Silizium im Polymerrückgrat ohne zusätzliches Anfärben ein Kontrast vorhanden ist. Die TEM-Aufnahmen zeigen deutlich die smektische Schichtstruktur innerhalb der Kolloide aus „verdünnten“ Copolysiloxanen und sind somit der erste direkte Beweis für die Mikrophasenseparation zwischen den Mesogenen und Polysiloxanketten, die bisher basierend auf Röntgenmessungen nur indirekt vorhergesagt wurde. Für die Copolysiloxane mit 2-Ring-Mesogenen wurden zwiebelartige Strukturen und für die Copolysiloxane mit 3-Ring-Mesogenen parallele Schichtstrukturen gefunden. Im ersten Fall folgt die smektische Schichtstruktur der Kugelsymmetrie des Kolloids, im zweiten Fall dominiert die Tendenz der smektischen Schichten, sich parallel anzuordnen.

On the cellular stress response to Staphylococcus aureus alpha-toxin

Staphylococcus aureus alpha-hemolysin was the first bacterial toxin recognized to form pores in the plasma membrane of eukaryotic cells. It is secreted as a water-soluble monomer that upon contact with target membranes forms an amphiphatic heptameric beta-barrel which perforates the bilayer. As a consequence, red cells undergo colloidosmotic lyses, while some nucleated cells may succumb to necrosis or programmed cell death. However, most cells are capable of repairing a limited number of membrane lesions, and then respond with productive transcriptional activation of NF-kB. In the present study, by using microarray and semiquantitative reverse transcriptase polymerase chain reaction (RT-PCR), data from a previously performed serial analysis of gene expression (SAGE) were extended and verified, revealing that immediate early genes (IEGs) such as c-fos, c-jun and egr-1 are strongly induced at 2-8 h after transient toxin treatment. Activating protein 1 (AP-1: c-Fos, c-Jun) binding activity was increased accordingly. As IEGs are activated by growth factors, these findings led to the discovery that -toxin promotes cell cycle progression of perforated cells in an EGFR-dependent fashion. Although the amount of c-fos mRNA rose rapidly after toxin treatment, c-Fos protein expression was observed only after a lag of about 3 h. Since translation consumes much ATP, which transiently drops after transient membrane perforation, the suspicion arised that membrane-perforation caused global, but temporary downregulation of translation. In fact, eIF2α became heavily phosphorylated minutes after cells had been confronted with the toxin, resulting in shutdown of protein synthesis before cellular ATP levels reached the nadir. GCN2 emerged as a candidate eIF2α kinase, since its expression rapidly increased in toxin-treated cells. Two hours after toxin treatment, GADD34 transcripts, encoding a protein that targets the catalytic subunit of protein phosphatase 1 (PP1) to the endoplasmic reticulum, were overexpressed. This was followed by dephosphorylation of eIF2α and resumption of protein synthesis. Addition of tautomycetin, a specific inhibitor of PP1, led to marked hyperphosphorylation of eIF2α and significantly reduced the drop of ATP-levels in toxin-treated cells. A novel link between two major stress-induced signalling pathways emerged when it was found that both translational arrest and restart were under the control of stress-activated protein kinase (SAPK) p38. The data provide an explanation for the indispensible role of p38 for defence against the archetypal threat of membrane perforation by agents that produce small transmembrane-pores.

Structuring of polymer surface by evaporation of sessile microdrops

In this thesis, we investigated the evaporation of sessile microdroplets on different solid substrates. Three major aspects were studied: the influence of surface hydrophilicity and heterogeneity on the evaporation dynamics for an insoluble solid substrate, the influence of external process parameters and intrinsic material properties on microstructuring of soluble polymer substrates and the influence of an increased area to volume ratio in a microfluidic capillary, when evaporation is hindered. In the first part, the evaporation dynamics of pure sessile water drops on smooth self-assembled monolayers (SAMs) of thiols or disulfides on gold on mica was studied. With increasing surface hydrophilicity the drop stayed pinned longer. Thus, the total evaporation time of a given initial drop volume was shorter, since the drop surface, through which the evaporation occurs, stays longer large. Usually, for a single drop the volume decreased linearly with t1.5, t being the evaporation time, for a diffusion-controlled evaporation process. However, when we measured the total evaporation time, ttot, for multiple droplets with different initial volumes, V0, we found a scaling of the form V0 = attotb. The more hydrophilic the substrate was, the more showed the scaling exponent a tendency to an increased value up to 1.6. This can be attributed to an increasing evaporation rate through a thin water layer in the vicinity of the drop. Under the assumption of a constant temperature at the substrate surface a cooling of the droplet and thus a decreased evaporation rate could be excluded as a reason for the different scaling exponent by simulations performed by F. Schönfeld at the IMM, Mainz. In contrast, for a hairy surface, made of dialkyldisulfide SAMs with different chain lengths and a 1:1 mixture of hydrophilic and hydrophobic end groups (hydroxy versus methyl group), the scaling exponent was found to be ~ 1.4. It increased to ~ 1.5 with increasing hydrophilicity. A reason for this observation can only be speculated: in the case of longer hydrophobic alkyl chains the formation of an air layer between substrate and surface might be favorable. Thus, the heat transport to the substrate might be reduced, leading to a stronger cooling and thus decreased evaporation rate. In the second part, the microstructuring of polystyrene surfaces by drops of toluene, a good solvent, was investigated. For this a novel deposition technique was developed, with which the drop can be deposited with a syringe. The polymer substrate is lying on a motorized table, which picks up the pendant drop by an upward motion until a liquid bridge is formed. A consecutive downward motion of the table after a variable delay, i.e. the contact time between drop and polymer, leads to the deposition of the droplet, which can evaporate. The resulting microstructure is investigated in dependence of the processes parameters, i.e. the approach and the retraction speed of the substrate and the delay between them, and in dependence of the intrinsic material properties, i.e. the molar mass and the type of the polymer/solvent system. The principal equivalence with the microstructuring by the ink-jet technique was demonstrated. For a high approach and retraction speed of 9 mm/s and no delay between them, a concave microtopology was observed. In agreement with the literature, this can be explained by a flow of solvent and the dissolved polymer to the rim of the pinned droplet, where polymer is accumulated. This effect is analogue to the well-known formation of ring-like stains after the evaporation of coffee drops (coffee-stain effect). With decreasing retraction speed down to 10 µm/s the resulting surface topology changes from concave to convex. This can be explained with the increasing dissolution of polymer into the solvent drop prior to the evaporation. If the polymer concentration is high enough, gelation occurs instead of a flow to the rim and the shape of the convex droplet is received. With increasing delay time from below 0 ms to 1s the depth of the concave microwells decreases from 4.6 µm to 3.2 µm. However, a convex surface topology could not be obtained, since for longer delay times the polymer sticks to the tip of the syringe. Thus, by changing the delay time a fine-tuning of the concave structure is accomplished, while by changing the retraction speed a principal change of the microtopolgy can be achieved. We attribute this to an additional flow inside the liquid bridge, which enhanced polymer dissolution. Even if the pendant drop is evaporating about 30 µm above the polymer surface without any contact (non-contact mode), concave structures were observed. Rim heights as high as 33 µm could be generated for exposure times of 20 min. The concave structure exclusively lay above the flat polymer surface outside the structure even after drying. This shows that toluene is taken up permanently. The increasing rim height, rh, with increasing exposure time to the solvent vapor obeys a diffusion law of rh = rh0  tn, with n in the range of 0.46 ~ 0.65. This hints at a non-Fickian swelling process. A detailed analysis showed that the rim height of the concave structure is modulated, unlike for the drop deposition. This is due to the local stress relaxation, which was initiated by the increasing toluene concentration in the extruded polymer surface. By altering the intrinsic material parameters i.e. the polymer molar mass and the polymer/solvent combination, several types of microstructures could be formed. With increasing molar mass from 20.9 kDa to 1.44 MDa the resulting microstructure changed from convex, to a structure with a dimple in the center, to concave, to finally an irregular structure. This observation can be explained if one assumes that the microstructuring is dominated by two opposing effects, a decreasing solubility with increasing polymer molar mass, but an increasing surface tension gradient leading to instabilities of Marangoni-type. Thus, a polymer with a low molar mass close or below the entanglement limit is subject to a high dissolution rate, which leads to fast gelation compared to the evaporation rate. This way a coffee-rim like effect is eliminated early and a convex structure results. For high molar masses the low dissolution rate and the low polymer diffusion might lead to increased surface tension gradients and a typical local pile-up of polymer is found. For intermediate polymer masses around 200 kDa, the dissolution and evaporation rate are comparable and the typical concave microtopology is found. This interpretation was supported by a quantitative estimation of the diffusion coefficient and the evaporation rate. For a different polymer/solvent system, polyethylmethacrylate (PEMA)/ethylacetate (EA), exclusively concave structures were found. Following the statements above this can be interpreted with a lower dissolution rate. At low molar masses the concentration of PEMA in EA most likely never reaches the gelation point. Thus, a concave instead of a convex structure occurs. At the end of this section, the optically properties of such microstructures for a potential application as microlenses are studied with laser scanning confocal microscopy. In the third part, the droplet was confined into a glass microcapillary to avoid evaporation. Since here, due to an increased area to volume ratio, the surface properties of the liquid and the solid walls became important, the influence of the surface hydrophilicity of the wall on the interfacial tension between two immiscible liquid slugs was investigated. For this a novel method for measuring the interfacial tension between the two liquids within the capillary was developed. This technique was demonstrated by measuring the interfacial tensions between slugs of pure water and standard solvents. For toluene, n-hexane and chloroform 36.2, 50.9 and 34.2 mN/m were measured at 20°C, which is in a good agreement with data from the literature. For a slug of hexane in contact with a slug of pure water containing ethanol in a concentration range between 0 and 70 (v/v %), a difference of up to 6 mN/m was found, when compared to commercial ring tensiometry. This discrepancy is still under debate.

Modeling of complex chemical reactions and macromolecular orientation phenomena in confined geometries

The cooperative motion algorithm was applied on the molecular simulation of complex chemical reactions and macromolecular orientation phenomena in confined geometries. First, we investigated the case of equilibrium step-growth polymerization in lamellae, pores and droplets. In such systems, confinement was quantified as the area/volume ratio. Results showed that, as confinement increases, polymerization becomes slower and the average molecular weight (MW) at equilibrium decreases. This is caused by the sterical hindrance imposed by the walls since chain growth reactions in their close vicinity have less realization possibilities. For reactions inside droplets at surfaces, contact angles usually increased after polymerization to compensate conformation restrictions imposed by confinement upon growing chains. In a second investigation, we considered monodisperse and chemically inert chains and focused on the effect of confinement on chain orientation. Simulations of thin polymer films showed that chains are preferably oriented parallel to the surface. Orientation increases as MW increases or as film thickness d decreases, in qualitative agreement with experiments with low MW polystyrene. It is demonstrated that the orientation of simulated chains results from a size effect, being a function of the ratio between chain end-to-end distance and d. This study was complemented by experiments with thin films of pi-conjugated polymers like MEH-PPV. Anisotropic refractive index measurements were used to analyze chain orientation. With increasing MW, orientation is enhanced. However, for MEH-PPV, orientation does not depend on d even at thicknesses much larger than the chain contour length. This contradiction with simulations was discussed by considering additional causes for orientation, for instance the appearance of nematic-like ordering in polymer films. In another investigation, we simulated droplet evaporation at soluble surfaces and reproduced the formation of wells surrounded by ringlike deposits at the surface, as observed experimentally. In our simulations, swollen substrate particles migrate to the border of the droplet to minimize the contact between solvent and vacuum, which costs the most energy. Deposit formation in the beginning of evaporation results in pinning of the droplet. When polymer chains at the substrate surface have strong uniaxial orientation, the resulting pattern is no longer similar to a ring but to a pair of half-moons. In a final stage, as an extension for the model developed for polymerization in nanoreactors, we studied the effect of geometrical confinement on a hypothetical oscillating reaction following the mechanism of the so called periodically forced Brusselator. It was shown that a reaction which is chaotic in the bulk may be driven to periodicity by confinement and vice-versa, opening new perspectives for chaos control.

Evaporation of sessile microdrops studied with microcantilevers

The aim of this work is to investigate the evaporation dynamics of water microdrops deposited on atomic force microscope cantilevers, which were employed as sensitive stress, mass and temperature sensors with high time resolution. The technique has some advantages with respect to video-microscope imaging and ultra-precision weighting with electronic microbalances or quartz crystal microbalances, since it allows to measure more drop parameters simultaneously for smaller drop sizes. On hydrophobic surfaces a single measurement with a silicon cantilever provides data for the drop mass, contact angle and radius until very close to complete evaporation. On hydrophilic surfaces, it is as well possible to measure drop mass and inclination of the cantilever. The technique further allows to detect differences between water microdrops evaporating from clean hydrophilic and hydrophobic surfaces. On hydrophilic surfaces the cantilever inclination is negative at the end of the evaporation process. Negative inclination mostly occurs when drops are pinned. This effect can not be detected with any of the other well-established methods. The evidence arises that on the hydrophilic surface a thin water film forms, while this is not the case for the hydrophobic surface. Metal coated cantilevers can be used as thermometers, and allow to precisely measure the temperature of an evaporating microdrop. This can be relevant for further applications of cantilevers as calorimetric sensors for chemical reactions taking place in drops on their surface. The applicability of Young’s equation was verified for microdrops. It was shown that Young’s equation can not be applied to microscopic drops due to their fast evaporation. A study on evaporation of microdrops in saturated vapor atmosphere was performed to estimate evaporation times and compare them with a theory developed, which relates the initial drop volume with the overall evaporation time.

Mixtures of colloidal rods and spheres in bulk and in confinement

When non-adsorbing polymers are added to an isotropic suspension of rod-like colloids, the colloids effectively attract each other via depletion forces. Monte Carlo simulations were performed to study the phase diagram of such rod-polymer mixtures. The colloidal rods were modelled as hard spherocylinders; the polymers were described as spheres of the same diameter as the rods. The polymers may overlap with no energy cost, while overlap of polymers and rods is forbidden. In this thesis the emphasis was on the depletion effects caused by the addition of spheres on the isotropic phase of rod-like particles. Although most of the present experimental studies consider systems close to or beyond the isotropic-nematic transition, the isotropic phase with depletion interactions turns out to be a not less interesting topic. First, the percolation problem was studied in canonical simulations of a system of hard rods and soft spheres, where the amount of depletant was kept low to prevent phase separation of the mixture. The lowering of the percolation threshold seen in experiment is confirmed to be due to the depletion interactions. The local changes in the structure of the fluid of rods, which were measured in the simulations, indicated that the depletion forces enhance local alignment and aggregation of the rods. Then, the phase diagram of isotropic-isotropic demixing of short spherocylinders was calculated using grand canonical ensemble simulations with successive umbrella sampling. Finite size scaling analysis allowed to estimate the location of the critical point. Also, estimates for the interfacial tension between the coexisting isotropic phases and analyses of its power-law behaviour on approach of the critical point are presented. The obtained phase diagram was compared to the predictions of the free volume theory. After an analysis of the bulk, the phase behaviour in confinement was studied. The critical point of gas-liquid demixing is shifted to higher concentrations of rods and smaller concentrations of spheres due to the formation of an orientationally ordered surface film. If the separation between the walls becomes very small, the critical point is shifted back to smaller concentrations of rods because the surface film breaks up. A method to calculate the contact angle of the liquid-gas interface with the wall is introduced and the wetting behaviour on the approach to the critical point is analysed.

Polymer-liquid crystal interface: a molecular dynamics study

Liquid crystals (LCs) are an interesting class of soft condensed matter systems characterized by an unusual combination of fluidity and long-range order, mainly known for their applications in displays (LCDs). However, the interest in LC continues to grow pushed by their application in new technologies in medicine, optical imaging, micro and nano technologies etc. In LCDs uniaxial alignment of LCs is mainly achieved by a rubbing process. During this treatment, the surfaces of polymer coated display substrates are rubbed in one direction by a rotating cylinder covered with a rubbing cloth. Basically, LC alignment involves two possible aligning directions: uniaxial planar (homogeneous) and vertical (homeotropic) to the display substrate. An interesting unresolved question concerning LCs regards the origin of their alignment on rubbed surfaces, and in particular on the polymeric ones used in the display industry. Most studies have shown that LCs on the surface of the rubbed polymer film layer are lying parallel to the rubbing direction. In these systems, micrometric grooves are generated on the film surface along the rubbing direction and also the polymer chains are stretched in this direction. Both the parallel aligned microgrooves and the polymer chains at the film surface may play a role in the LC alignment and it is not easy to quantify the effect of each contribution. The work described in this thesis is an attempt to find new microscopic evidences on the origin of LC alignment on polymeric surfaces through molecular dynamics (MD) simulations, which allow the investigation of the phenomenon with atomic detail. The importance of the arrangement of the polymeric chains in LCs alignment was studied by performing MD simulations of a thin film of a typical nematic LC, 4-cyano-4’-pentylbiphenyl (5CB), in contact with two different polymers: poly(methyl methacrylate)(PMMA) and polystyrene (PS). At least four factors are believed to influence the LC alignment: 1. the interactions of LCs with the backbone vinyl chains; 2. the interactions of LCs with the oriented side groups; 3. the anisotropic interactions of LCs with nanometric grooves; 4. the presence of static surface charges. Here we exclude the effect of microgrooves and of static surface charges from our virtual experiment, by using flat and neutral polymer surfaces, with the aim of isolating the chemical driving factors influencing the alignment of LC phases on polymeric surfaces.

Molecular organization of n-cyanobiphenyl liquid crystals on a molybdenite surface

The alignement and anchoring of liquid crystals on solid surfaces is a key problem for modern device technology that until now has been treated empirically, but that can now be tackled by atomistic computer simulations. Molecular dynamics (MD) simulations were used in this thesis work to study two films of 7 and 8 n-alkyl-4’cyanobiphenyl (7CB and 8CB) liquid crystals , with a thickness of 15 nm, confined between two (001) surfaces of MoS2 (molybdenite). The isotropic and nematic phases of both liquid crystals were simulated, and the resulting structures characterized structurally. A new force field was designed to model the interactions between the liquid crystal (LC) molecules and the surface of molybdenite, while an accurate force field developed previously was used to model the 7CB and 8CB molecules. The results show that the (001) molybdenite surface induces a planar orientation in both the liquid crystals. For the nematic phase of 8CB, one of the two solid/LC interfaces is composed of a first layer of molecules aligned parallel to the surface, followed by a second layer of molecules aligned perpendicular to the surface (also called, homeotropic). The effect of the surface appears to be local in nature as it is confined to the first 15 Angström of the LC film. Conversely, for the nematic phase of 7CB, a planar ordering is established into the LC film. The LC molecules at the interface with the molybdenite appear to align preferentially their alkyl chains toward the solid substrate. The resulting tilt angle of molecules was found to be in good agreement with experimental measurements available in literature. Despite the fact that the MD simulations spanned a time range of more than 100 ns, the nematic phases of both 7CB and 8CB were found not to be completely formed. In order to confirm the findings presented in this thesis, we propose to extend the current study.

Modeling and simulations of some anisotropic soft-matter systems: from biaxial to chiral materials

We have modeled various soft-matter systems with molecular dynamics (MD) simulations. The first topic concerns liquid crystal (LC) biaxial nematic (Nb) phases, that can be possibly used in fast displays. We have investigated the phase organization of biaxial Gay-Berne (GB) mesogens, considering the effects of the orientation, strength and position of a molecular dipole. We have observed that for systems with a central dipole, nematic biaxial phases disappear when increasing dipole strength, while for systems characterized by an offset dipole, the Nb phase is stabilized at very low temperatures. In a second project, in view of their increasing importance as nanomaterials in LC phases, we are developing a DNA coarse-grained (CG) model, in which sugar and phosphate groups are represented with Lennard-Jones spheres, while bases with GB ellipsoids. We have obtained shape, position and orientation parameters for each bead, to best reproduce the atomistic structure of a B-DNA helix. Starting from atomistic simulations results, we have completed a first parametrization of the force field terms, accounting for bonded (bonds, angles and dihedrals) and non-bonded interactions (H-bond and stacking). We are currently validating the model, by investigating stability and melting temperature of various sequences. Finally, in a third project, we aim to explain the mechanism of enantiomeric discrimination due to the presence of a chiral helix of poly(gamma-benzyl L-glutamate) (PBLG), in solution of dimethylformamide (DMF), interacting with chiral or pro-chiral molecules (in our case heptyl butyrate, HEP), after tuning properly an atomistic force field (AMBER). We have observed that DMF and HEP molecules solvate uniformly the PBLG helix, but the pro-chiral solute is on average found closer to the helix with respect to the DMF. The solvent presents a faster isotropic diffusion, twice as HEP, also indicating a stronger interaction of the solute with the helix.

Studio di caratteri correlati a stress idrico in una collezione di cultivar di frumento duro (Triticum durum Desf.)

L’agricoltura si trova ad affrontare una diminuzione della disponibilità d’acqua ed una crescente domanda della produzione di cereali per scopi alimentari. Sono perciò necessarie strategie di coltivazione innovative per migliorare la produttività e nuovi genotipi migliorati nell'efficienza dell’uso delle risorse in condizioni di siccità. Questi rappresentano gli obietti principali del progetto “DROPS” (Drought tolerant yielding Plants) all’interno del quale ha avuto luogo il mio progetto di Dottorato. La mia attività di ricerca è stata svolta come segue: 1. Caratterizzazione molecolare di un panel di188 accessioni di frumento duro con marcatori SSR e DaRT; 2. Esperimenti in serra su 100 accessioni del panel per valutare la Water-Use Efficiency (WUE) in sei repliche secondo un Alpha Lattice design; 3. Prove sul campo, effettuate secondo un Alpha Lattice design, in due stagioni di crescita: a. 2010/11, valutazione di 100 accessioni presso l’Azienda sperimentale dell'Università di Cadriano (BO); b. 2011/12, valutazione del panel completo in 3 ambienti, con due diversi regimi irrigui In entrambi gli anni, abbiamo valutato caratteri agronomici correlati con il ciclo di sviluppo, la resa di granella e sue componenti, nonché diversi fattori ambientali e del suolo. Per quanto riguarda WUE, abbiamo trovato differenze altamente significative tra accessioni; inoltre, cinque accessioni hanno mostrato elevati valori di WUE e cinque accessioni valori molto bassi di WUE in tutte e sei le repliche. Gli esperimenti di campo nelle stagioni 2011 e 2012 hanno evidenziato differenze altamente significative tra le accessioni del panel per la maggior parte dei caratteri analizzati, confermando inoltre che il panel di fiorisce entro una settimana. L'esperimento del secondo anno ci ha permesso osservare un significativa interazione Genotipo X Ambiente. Questi risultati saranno integrati con ulteriori analisi QTL, per identificare regioni cromosomiche coinvolte nel controllo genetico dei caratteri di interesse e verificare la stabilità dei QTL in diversi ambienti.

Laser driven proton acceleration and beam shaping

In the race to obtain protons with higher energies, using more compact systems at the same time, laser-driven plasma accelerators are becoming an interesting possibility. But for now, only beams with extremely broad energy spectra and high divergence have been produced. The driving line of this PhD thesis was the study and design of a compact system to extract a high quality beam out of the initial bunch of protons produced by the interaction of a laser pulse with a thin solid target, using experimentally reliable technologies in order to be able to test such a system as soon as possible. In this thesis, different transport lines are analyzed. The first is based on a high field pulsed solenoid, some collimators and, for perfect filtering and post-acceleration, a high field high frequency compact linear accelerator, originally designed to accelerate a 30 MeV beam extracted from a cyclotron. The second one is based on a quadruplet of permanent magnetic quadrupoles: thanks to its greater simplicity and reliability, it has great interest for experiments, but the effectiveness is lower than the one based on the solenoid; in fact, the final beam intensity drops by an order of magnitude. An additional sensible decrease in intensity is verified in the third case, where the energy selection is achieved using a chicane, because of its very low efficiency for off-axis protons. The proposed schemes have all been analyzed with 3D simulations and all the significant results are presented. Future experimental work based on the outcome of this thesis can be planned and is being discussed now.

Modeling and simulations of nanoparticles in liquid crystalline systems

The aim of this work is to investigate, using extensive Monte Carlo computer simulations, composite materials consisting of liquid crystals doped with nanoparticles. These systems are currently of great interest as they offer the possibility of tuning the properties of liquid crystals used in displays and other devices as well as providing a way of obtaining regularly organized systems of nanoparticles exploiting the molecular organization of the liquid crystal medium. Surprisingly enough, there is however a lack of fundamental knowledge on the properties and phase behavior of these hybrid materials, making the route to their application an essentially empirical one. Here we wish to contribute to the much needed rationalization of these systems studying some basic effects induced by different nanoparticles on a liquid crystal host. We investigate in particular the effects of nanoparticle shape, size and polarity as well as of their affinity to the liquid crystal solvent on the stability of the system, monitoring phase transitions, order and molecular organizations. To do this we have proposed a coarse grained approach where nanoparticles are modelled as a suitably shaped (spherical, rod and disk like) collection of spherical Lennard-Jones beads, while the mesogens are represented with Gay-Berne particles. We find that the addition of apolar nanoparticles of different shape typically lowers the nematic–isotropic transition of a non-polar nematic, with the destabilization being greater for spherical nanoparticles. For polar mesogens we have studied the effect of solvent affinity of the nanoparticles showing that aggregation takes places for low solvation values. Interestingly, if the nanoparticles are polar the aggregates contribute to stabilizing the system, compensating the shape effect. We thus find the overall effects on stability to be a delicate balance of often contrasting contributions pointing to the relevance of simulations studies for understanding these complex systems.