ZnO film based surface acoustic wave micro-pump

In this study, a micro-pump unit based on surface acoustic wave (SAW) on piezoelectric ZnO film is designed and fabricated as a micro-fluidic device. It employs a mechanical wave, which is generated electrically using an aluminum interdigital transducer (IDT), and propagates on the surface of the ZnO film. The ZnO film was used in this study because it has a high electromechanical coefficient and an excellent bonding with various substrate materials, in particular silicon. The sputtering parameters for ZnO film deposition have been optimized, and the ZnO films with different thickness from 1 micron to 5.5 microns were prepared. The film properties have been characterized using different methods, such as scanning electron microscopy, X-ray diffraction and atomic force microscopy. Aluminum IDT with a finger width and spacing of 8 microns was patterned on the ZnO film using a lift-off process. The frequency generated was measured using a network analyzer, and it varies from 130 MHz to 180 MHz as a function of film thickness. A signal generator was used to generate the frequency with a power amplifier to amplify the signal, which was then applied to aluminum IDT to generate the surface acoustic wave. If a liquid droplet exists on the surface carrying the acoustic wave, the energy and the momentum of the SAW will be coupled into the fluid, causing the liquid to vibrate and move on film surface. The strength of this movement is determined by the applied voltage and frequency. The volume of the liquid drop loaded on the SAW device in this study is of several hundreds of nanoliters. The movement of the liquid inside the droplet and also on the ZnO film surface can be demonstrated. The performance of ZnO SAW device was characterized as a function of film thickness. © 2007 IOP Publishing Ltd.

Preliminary Investigation of Fluid Flow in Meso-Scale Rectangular Tube

The fluid flow associated with micro and meso scale devices is currently of interest. Experiments were performed to study the fluid flow in meso-scale channels. A straight flow tube was fabricated with 1.0x4.0mm^2 in rectangular cross section and 200mm in length, which was made of quartz for flow visualization and PIV measurements. Reynolds numbers were ranged from 311 to over 3105. The corresponding pressure drop was from 0.65KPa to over 16.58KPa between the inlet and outlet of the tube. The micro PIV was developed to measure the velocity distribution in the tube. A set of microscope object lens was mounted ahead of CCD camera to obtain optimized optical magnification on the CCD chip. The velocity distributions near the outlet of the tube were measured to obtain full-developed flow. A CW laser beam was focused directly on the test section by a cylinder lens to form a small light sheet. Thus, high power density of light was formed on the view region. It is very important to the experiment while the velocity of the flow reaches to a few meters per second within millimeter scale. In this case, it is necessary to reduce exposure time to microseconds for PIV measurements. In the present paper, the experimental results are compared with the classical theories.

(Ti,Al)N Film On Normalized T8 Carbon Tool Steel Prepared By Pulsed High Energy Density Plasma Technique

Under optimized operating parameters, a hard and wear resistant ( Ti,Al)N film is prepared on a normalized T8 carbon tool steel substrate by using pulsed high energy density plasma technique. Microstructure and composition of the film are analysed by x-ray diffraction, x-ray photoelectron spectroscopy, Auger electron spectroscopy and scanning electron microscopy. Hardness profile and tribological properties of the film are tested with nano-indenter and ring-on-ring wear tester, respectively. The tested results show that the microstructure of the film is dense and uniform and is mainly composed of ( Ti,Al)N and AlN hard phases. A wide transition interface exists between the film and the normalized T8 carbon tool steel substrate. Thickness of the film is about 1000 nm and mean hardness value of the film is about 26GPa. Under dry sliding wear test conditions, relative wear resistance of the ( Ti,Al)N film is approximately 9 times higher than that of the hardened T8 carbon tool steel reference sample. Meanwhile, the ( Ti,Al)N film has low and stable friction coefficient compared with the hardened T8 carbon tool steel reference sample.

Simultaneous Laser-Induced Fluorescence And Contactless-Conductivity Detection For Microfluidic Chip

A combined detection system involving simultaneous LIF and contactless-conductometric measurements at the same place of the microfluidic chip was described. The LIF measurement was designed according to the confocal principle and a moveable contactless-conductivity detector was used in (CD)-D-4. Both measurements were mutually independent and advantageous in analyses of mixtures. Various experimental parameters affecting the response were examined and optimized. The performances were demonstrated by simultaneous detection of Rhodamine B. And the results showed that the combined detection system could be used sensitively and reliably. (C) 2008 Yong Yu. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.

Laser synthesizing NiAl intermetallic and TiC reinforced NiAl intermetallic matrix composite

The NiAl intermetallic layers and NiAl matrix composite layers with TiC particulate reinforcement were successfully synthesized by laser cladding with coaxial powder feeding of Ni/Al clad powder and Ni/Al + TiC powder mixture, respectively. With optimized processing parameters and powder mixture compositions, the synthesized layers were free of cracks and metallurgical bond with the substrate. The microstructure of the laser-synthesized layers was composed of 6-NiAl phase and a few gamma phases for NiAl intermetallic; unmelted TiC, dispersive fine precipitated TiC particles and refined beta-NiAl phase matrix for TiC reinforced NiAl intermetallic composite. The average microhardness was 355 HV0.1 and 538 HV0.1, respectively. Laser synthesizing and direct metal depositing offer promising approaches for producing NiAl intermetallic and TiC-reinforced NiAl metal matrix composite coatings and for fabricating NiAl intermetallic bulk structure. (C) 2004 Laser Institute of America.

Quantum and variational monte-carlo interaction potentials for li2 (x1-sigma-g+)

Optimized trial functions are used in quantum Monte Carlo and variational Monte Carlo calculations of the Li₂(X ¹Σ⁺_g) potential curve. The trial functions used are a product of a Slater determinant of molecular orbitals multiplied by correlation functions of electron—nuclear and electron—electron separation. The parameters of the determinant and correlation functions are optimized simultaneously by reducing the deviations of the local energy E_L (E_L  Ψ⁻¹_THΨ_T, where Ψ_T denotes a trial function) over a fixed sample. At the equilibrium separation, the variational Monte Carlo and quantum Monte Carlo methods recover 68% and 98% of the correlation energy, respectively. At other points on the curves, these methods yield similar accuracies.

Chemical recycling of municipal packaging waste by pyrolysis

[EN]The present doctoral thesis centers on studying pyrolysis as a chemical recycling technique for rejected packaging waste fractions coming from separation and sorting plants. The pyrolysis experiments have been carried out in a lab-scale installation equipped with a 3.5 L semi-batch reactor and a condensation and collection system for the liquids and gases generated. In the present thesis, an experimental study on the conventional pyrolysis process applied to the aforementioned waste fractions has been conducted, as well as the study of non-conventional or advanced pyrolysis processes such as catalytic and stepwise pyrolysis. The study of the operating parameters has been carried out using a mixed plastics simulated sample, the composition of which is similar to that found in real fractions, and subsequently the optimized process has been applied to real packaging waste. An exhaustive characterization of the solids, liquids and gases obtained in the process has been made after each experiment and their potential uses have been established. Finally, an empirical model that will predict the pyrolysis yields (% organic liquid, % aqueous liquid, % gases, % char, % inorganic solid) as a function of the composition of the initial sample has been developed. As a result of the experimental work done, the requirements have been established for an industrial packaging waste pyrolysis plant that aims to be sufficiently versatile as to generate useful products regardless of the nature of the raw material.

MBARI procedures for automated nutrient analyses using a modified Alpkem Series 300 Rapid Flow Analyzer

This report documents the methods used at the Monterey Bay Aquarium Research Institute (MBARI) for analyzing seawater nutrient samples with an Alpkem Series 300 Rapid Flow Analyzer (RFA) system. The methods have been optimized for the particular requirements of this laboratory. The RFA system has been used to analyze approximately 20,000 samples during the past two years. The methods have been optimized to run nutrient analyses in a routine manner with a detection limit of better than -±1% and a within run precision of -±1% of the full scale concentration range. The normal concentration ranges are 0-200 ~M silicate, 0-5 ~M phosphate, 0-50 ~M nitrate, 0-3 ~M nitrite, and 0-10 ~M ammonium. The memorandum is designed to be used in a loose-leaf binder format. Each page is dated and as revisions are made, they should be inserted into the binder. The revisions should be added into the binder. Retain the old versions in order to maintain a historical record of the procedures. (88 pages)

Una nueva aproximación a la síntesis de heterociclos pirrolofusionados basada en la reacción de amidación de alquinos asistida por el reactivo de yodo hipervalente PIFA

458 p.

Habitat mapping effort at the Olympic Coast National Marine Sanctuary – Current status and future needs

With elevating interest to establish conservation efforts for groundfish stocks and continued scrutiny over the value of marine protected areas along the west coast, the importance of enhancing our knowledge of seabed characteristics through mapping activities is becoming increasingly more important, especially in a timely manner. Shortly after the inception of the Seabed Mapping Initiative instituted with the US Geological Survey (USGS), the National Marine Sanctuary Program (NMSP) assembled a panel of habitat mapping experts. They determined that the status of existing data sets and future data acquisition needs varied widely among the individual sanctuaries and that more detailed site assessments were needed to better prioritize mapping efforts and outline an overall joint strategy. To assist with that specific effort and provide pertinent information for the Olympic Coast National Marine Sanctuary’s (OCNMS) Management Plan Review, this report summarizes the mapping efforts that have taken place at the site to date; calculates a timeframe for completion of baseline mapping efforts when operating under current data acquisition limitations; describes an optimized survey strategy to dramatically reduce the required time to complete baseline surveying; and provides estimates for the needed vessel sea-days (DAS) to accomplish baseline survey completion within a 2, 5 and 10 year timeframe. (PDF contains 38 pages.)

Scientific Data Application Profile Scoping Study

This study was undertaken by UKOLN on behalf of the Joint Information Systems Committee (JISC) in the period April to September 2008. Application profiles are metadata schemata which consist of data elements drawn from one or more namespaces, optimized for a particular local application. They offer a way for particular communities to base the interoperability specifications they create and use for their digital material on established open standards. This offers the potential for digital materials to be accessed, used and curated effectively both within and beyond the communities in which they were created. The JISC recognized the need to undertake a scoping study to investigate metadata application profile requirements for scientific data in relation to digital repositories, and specifically concerning descriptive metadata to support resource discovery and other functions such as preservation. This followed on from the development of the Scholarly Works Application Profile (SWAP) undertaken within the JISC Digital Repositories Programme and led by Andy Powell (Eduserv Foundation) and Julie Allinson (RRT UKOLN) on behalf of the JISC. Aims and Objectives 1.To assess whether a single metadata AP for research data, or a small number thereof, would improve resource discovery or discovery-to-delivery in any useful or significant way. 2.If so, then to:a.assess whether the development of such AP(s) is practical and if so, how much effort it would take; b.scope a community uptake strategy that is likely to be successful, identifying the main barriers and key stakeholders. 3.Otherwise, to investigate how best to improve cross-discipline, cross-community discovery-to-delivery for research data, and make recommendations to the JISC and others as appropriate. Approach The Study used a broad conception of what constitutes scientific data, namely data gathered, collated, structured and analysed using a recognizably scientific method, with a bias towards quantitative methods. The approach taken was to map out the landscape of existing data centres, repositories and associated projects, and conduct a survey of the discovery-to-delivery metadata they use or have defined, alongside any insights they have gained from working with this metadata. This was followed up by a series of unstructured interviews, discussing use cases for a Scientific Data Application Profile, and how widely a single profile might be applied. On the latter point, matters of granularity, the experimental/measurement contrast, the quantitative/qualitative contrast, the raw/derived data contrast, and the homogeneous/heterogeneous data collection contrast were discussed. The Study report was loosely structured according to the Singapore Framework for Dublin Core Application Profiles, and in turn considered: the possible use cases for a Scientific Data Application Profile; existing domain models that could either be used or adapted for use within such a profile; and a comparison existing metadata profiles and standards to identify candidate elements for inclusion in the description set profile for scientific data. The report also considered how the application profile might be implemented, its relationship to other application profiles, the alternatives to constructing a Scientific Data Application Profile, the development effort required, and what could be done to encourage uptake in the community. The conclusions of the Study were validated through a reference group of stakeholders.

Design,optimization and in vivo evaluation of non-viral vectors for gene therapy. Applications in ocular disorders

227 págs.

Desarrollo de nanopartículas sólidas lipídicas como sistemas de administración de ADN para terapia génica

290 p. (Bibliogr. 257-290) Correo electrónico de la autora: ana.delpozo@ehu.es

Activación de aldehídos a,b-insaturados mediante aminocatálisis en procesos enantioselectivos. Cicloadiciones (3+2) y reacciones en cascada Michael/Henry

During the research that it is summarized in the present memory, the activation of enals via iminium ion catalysis in different transformations has been studied. Firstly, a 1,3-dipolar cycloaddition between stable azomethine ylides and a,b-unsaturated aldehydes catalyzed by a chiral imidazolidinone derivative has been optimized. Employing this methodology we have synthesized a large range of densely substituted pyrroloisoquinolines and pyrrolophthalazines with good yields and high values of diastereo- and enantioselectivity. Moreover, a mechanistic study has been carried out based on DFT calculations and experimental data which have allowed us to propose that the (3+2) cycloaddition reaction follows a sequential Michael addition/Mannich cyclization pathway. The formation of the iminium ion as a result of the condensation between the a,b-unsaturated aldehyde and the catalyst plays an essential role, regarding both reactivity and stereoselectivity. On the other hand we have developed a methodology to carry out a cascade Michael/Henry reaction followed by a sequential dehydration. Starting from simple substrates (2-nitromethylacrilates and a,b-unsaturated aldehydes) and employing a prolinol-derivative catalyst a series of quiral nitrocyclohexadienes have been synthesized.

Two-Phase Flow In Anode Flow Field Of A Small Direct Methanol Fuel Cell In Different Gravities

An in-situ visualization of two-phase flow inside anode flow bed of a small liquid fed direct methanol fuel cells in normal and reduced gravity has been conducted in a drop tower. The anode flow bed consists of 11 parallel straight channels. The length, width and depth of single channel, which had rectangular cross section, are 48.0, 2.5 and 2.0 mm, respectively. The rib width was 2.0 mm. The experimental results indicated that when the fuel cell orientation is vertical, two-phase flow pattern in anode channels can evolve from bubbly flow in normal gravity into slug flow in microgravity. The size of bubbles in the reduced gravity is also bigger. In microgravity, the bubbles rising speed in vertical channels is obviously slower than that in normal gravity. When the fuel cell orientation is horizontal, the slug flow in the reduced gravity has almost the same characteristic with that in normal gravity. It implies that the effect of gravity on two-phase flow is small and the bubbles removal is governed by viscous drag. When the gas slugs or gas columns occupy channels, the performance of liquid fed direct methanol fuel cells is failing rapidly. It infers that in long-term microgravity, flow bed and operating condition should be optimized to avoid concentration polarization of fuel cells.