Nitrous oxide emissions from an intermittent aeration activated sludge system of an urban wastewater treatment plant

This study investigated the emission of N2O during the sequential aerated (60-min) and non-aerated (30-min) stages of an intermittent aeration cycle in an activated sludge wastewater treatment plant (WWTP). N2O emission occurred during both stages; however, emission was much higher during aeration. Air stripping is the major factor controlling transfer of N2O from the sewage to the atmosphere. The N2O emissions exclusively from the aeration tank represented 0.10% of the influent total nitrogen load and the per capita emission factor was almost 3 times higher than that suggested by the IPCC for inventories of N2O emission from WWTPs.

Potencial uso de serpentinito no armazenamento mineral do CO2

Rising anthropogenic CO2 emissions are considered a major contributor to the greenhouse effect. There are several options for reducing atmospheric CO2 levels, and among these alternatives, Carbon Capture and Storage (CCS) has been identified as an effective and promising approach. This work investigated the feasibility of using serpentinite as a vehicle for carbon storage presenting a source-sink match. The main results of the work confirmed that serpentinite is appropriate for the carbonation process due to the high concentration of Mg in its composition.

VOC emissions and control techniques in softwood veneer dryers

The objective in this Master’s Thesis was to determine VOC emissions from veneer drying in softwood plywood manufacturing. Emissions from plywood industry have become an important factor because of the tightened regulations worldwide. In this Thesis is researched quality and quantity of the VOCs from softwood veneer drying. One of the main objectives was to find out suitable cleaning techniques for softwood VOC emissions. In introduction part is presented veneer drying machines, wood mechanical and chemical properties. VOC control techniques and specified VOC limits are introduced also in the introduction part. Plywood mills have not had interest to VOC emissions previously nevertheless nowadays plywood mills worldwide must consider reduction of the emissions. This Thesis includes measuring of emissions from softwood veneer dryer, analyzation of measured test results and reviewing results. Different air conditions inside of the dryer were considered during planning of the measurements. Results of the emissions measurements were compared to the established laws. Results from this Thesis were softwood veneer dryer emissions in different air conditions. Emission control techniques were also studied for softwood veneer dryer emissions for further specific research.

Permanent Magnet Synchronous Machine for Parallel Hybrid Vehicle

The aim of this thesis is to describe hybrid drive design problems, the advantages and difficulties related to the drive. A review of possible hybrid constructions, benefits of parallel, series and series-parallel hybrids is done. In the thesis analytical and finite element calculations of permanent magnet synchronous machines with embedded magnets were done. The finite element calculations were done using Cedrat’s Flux 2D software. This machine is planned to be used as a motor-generator in a low power parallel hybrid vehicle. The boundary conditions for the design were found from Lucas-TVS Ltd., India. Design Requirements, briefly: • The system DC voltage level is 120 V, which implies Uphase = 49 V (RMS) in a three phase system. • The power output of 10 kW at base speed 1500 rpm (Torque of 65 Nm) is desired. • The maximum outer diameter should not be more than 250 mm, and the maximum core length should not exceed 40 mm. The main difficulties which the author met were the dimensional restrictions. After having designed and analyzed several possible constructions they were compared and the final design selected. Dimensioned and detailed design is performed. Effects of different parameters, such as the number of poles, number of turns and magnetic geometry are discussed. The best modification offers considerable reduction of volume.

A vehicle for message

Soitinnus: piano, rummut, ääninauha?

Sähkö- ja hybridiautojen voimansiirtojärjestelmien jännitetasot

Kasvihuonekaasu- ja hiilidioksidipäästöt ovat kasvaneet viimeisten vuosikymmenten aikana merkittävästi. Merkittävimpiä päästöjen lähteitä ovat liikenteessä ja energiantuotannossa käytetyt fossiiliset polttoaineet. Kaikista maailman kasvihuonepäästöistä liikenne aiheuttaa noin 13 %, josta yli 80 % on tieliikenteen aiheuttamia päästöjä. Jotta tieliikenteen ai-heuttamia päästöjä saataisiin vähennettyä on tieliikenteeseen kehitettävä yhä vähäpäästöisempiä ja päästöttömiä kulkuvälineitä. Tämä on ollut yksi päätekijä sähkö- ja hybridiautojen kehitykseen. Tässä kandidaatintyössä selvitetään sähkö- ja hybridiautoissa käytettyjä jännitetasoja sekä voimansiirtojärjestelmissä käytettyjä komponentteja. Työ rajoittuu ainoastaan henkilöautoihin, joista tarkastelun kohteena ovat sähkö-, hybridi- ja muunnossähköautot. Työssä tarkastellaan myös sähkö- ja hybridiautojen tulevaisuuden näkymiä turvallisuuden ja standardoinnin kannalta. Työssä esitettyjen tietojen perusteella saadaan selkeä näkemys siitä, miten käytetyt jännitetasot ja komponentit vaihtelevat eri autovalmistajien kesken. Korkeammat jännitetasot ovat energiatehokkuuden kannalta parempia, mutta aiheuttavat vaatimuksia käyttöturvallisuuteen liittyvissä kysymyksissä.

Marketing Plan of Electric Vehicle Charging Solutions to USA

The purpose of the Thesis was to evaluate the business environment of electrical vehicle charging equipment (EVSE) in USA, find the key issues of entering the US EVSE markets and to form a marketing plan for possible market entry. The external market research analyzed the environment, customers, competitors and demand of EVSEs. In the internal analysis the focus was on resources and capabilities, offering, performance, business relations and US related issues. The research about the business environment was done using already available information from market studies and seminars. In external analysis there were also two semi-structured interviews from market experts used. The internal analysis was done mostly by interviews, but also company’s internal data sources were used. The interviews were semi-constructed and included eight interviewees from each part of EVSE value chain. The research findings were analyzed using SWOT analysis, which was converted to a so called TOWS matrix for extracting strategies. As a result of the Thesis, valuable information about the US markets and their requirements for EVSEs was gained. By matching the strengths of the case company and market requirements, customer segmentation and targeting were done and a marketing plan was constructed for the case company to help their management to evaluate the feasibility of possible market entry and investments to USA.

Crop residues on short-term CO2 emissions in sugarcane production areas

The proper management of agricultural crop residues could produce benefits in a warmer, more drought-prone world. Field experiments were conducted in sugarcane production areas in the Southern Brazil to assess the influence of crop residues on the soil surface in short-term CO2 emissions. The study was carried out over a period of 50 days after establishing 6 plots with and without crop residues applied to the soil surface. The effects of sugarcane residues on CO2 emissions were immediate; the emissions from residue-covered plots with equivalent densities of 3 (D50) and 6 (D100) t ha-1 (dry mass) were less than those from non-covered plots (D0). Additionally, the covered fields had lower soil temperatures and higher soil moisture for most of the studied days, especially during the periods of drought. Total emissions were as high as 553.62 ± 47.20 g CO2 m-2, and as low as 384.69 ± 31.69 g CO2 m-2 in non-covered (D0) and covered plot with an equivalent density of 3 t ha-1 (D50), respectively. Our results indicate a significant reduction in CO2 emissions, indicating conservation of soil carbon over the short-term period following the application of sugarcane residues to the soil surface.

Control of ammonia emissions in naturally ventilated dairy cattle facilities in Portugal

We conducted a study of the processes associated to NH3 emission in naturally ventilated dairy cattle facilities, having described factors that regulate NH3 emission, as well as methodologies for measuring these emissions at these facilities. Appropriate techniques to mitigate NH3 emission in facilities located in regions with warm climates were also identified. The most effective mitigation techniques with simple implementation include strategies associated to: (i) installation design and flooring, which lead to reduced emissions, (ii) excreta pre-excretion, namely the use of diets with optimized crude protein content and increased milk production at farm level; and (iii) excreta post-excretion, particularly by changing the conditions of environmental monitoring within the premises, practice introduction or additive application in the management of excreta deposited on floors.

Liikennebiokaasun tuotannon ja käytön ulkoiset kustannukset Pohjois-Karjalassa

Työn tavoitteena oli selvittää liikennebiokaasuntuotannon ja käytön vaikutus liikenteen ulkoi-siin kustannuksiin Pohjois-Karjalassa. Biokaasua tuotetaan Joensuussa Kuhasalon jäteveden-puhdistamolla sekä Kontiosuon jäteasemalla, Kiteellä biokaasua tuotetaan BioKympin yh-teismädätyslaitoksessa. Lisäksi laskennassa huomioitiin yhden maatilakokoluokan biokaasun-tuotanto. Työssä selvitettiin kaksi skenaariota liikennebiokaasun tuotantomääräksi vuodelle 2015. Liikennebiokaasua voitaisiin tuottaa optimiskenaarion mukaan 3 426 MWh ja maksimi-tuotantoskenaarion mukaan 21 532 MWh. Liikennebiokaasun käytön vaikutukset liikenteen päästöihin laskettiin vuodelle 2015 ja vuo-delle 2020, jolloin liikennebiokaasua käytettäisiin 10 % liikenteen energiantarpeesta Pohjois-Karjalassa. Hiilidioksidipäästöt vähenevät vuoden 2020 tilanteessa samassa suhteessa kuin liikennebiokaasu korvaa fossiilisia polttoaineita. Muista päästöistä merkittävimmät päästövä-hennykset saatiin kun vuoden 2010 dieselautot muutettaisiin biokaasuautoiksi, tällöin hiuk-kaspäästöt alenisivat jopa 18 % vuoden 2010 päästöistä. Lisäksi selvitettiin liikenteen päästöjen pienenemisen vaikutus liikenteen aiheuttamiin ulkoisiin kustannuksiin. Laskettavat ulkoiset kustannukset olivat ilmastonmuutos, pakokaasupäästöt sekä energiariippuvuus. Pakokaasupäästöjen aiheuttamat ulkoiset kustannukset olivat vuonna 2010 noin 7 miljoonaa euroa. Liikennebiokaasua käyttävästä ajoneuvotyypistä riippuen ulkoiset kustannukset laskevat vuoden 2020 tilanteessa 10–16 % vuoden 2010 kustannuksista. Ilmastonmuutoksen ulkoiset kustannukset vuodelle 2010 olivat 9,5 miljoonaa euroa. Biokaasun käytön avulla kustannuksissa voitaisiin säästää 910 000 euroa vuonna 2020. Ener-giariippuvuuden hinta öljynkäytöstä oli vuonna 2010 noin 4,2 miljoonaa euroa ja vuonna 2020 kustannukset voisivat laskea 450 000 euroa.

Design and Control of Permanent Magnet Synchronous Machine for Hybrid Electric Vehicle

This master’s thesis mainly focuses on the design requirements of an Electric drive for Hybrid car application and its control strategy to achieve a wide speed range. It also emphasises how the control and performance requirements are transformed into its design variables. A parallel hybrid topology is considered where an IC engine and an electric drive share a common crank shaft. A permanent magnet synchronous machine (PMSM) is used as an electric drive machine. Performance requirements are converted into Machine design variables using the vector model of PMSM. Main dimensions of the machine are arrived using analytical approach and Finite Element Analysis (FEA) is used to verify the design and performance. Vector control algorithm was used to control the machine. The control algorithm was tested in a low power PMSM using an embedded controller. A prototype of 10 kW PMSM was built according to the design values. The prototype was tested in the laboratory using a high power converter. Tests were carried out to verify different operating modes. The results were in agreement with the calculations.

Design of salient pole PM synchronous machines for a vehicle traction application – Analysis and

This doctoral thesis presents a study on the development of a liquid-cooled frame salient pole permanent-magnet-exited traction machine for a four-wheel-driven electric car. The emphasis of the thesis is put on a radial flux machine design in order to achieve a light-weight machine structure for traction applications. The design features combine electromagnetic and thermal design methods, because traction machine operation does not have a strict operating point. Arbitrary load cycles and the flexible supply require special attention in the design process. It is shown that accurate modelling of the machine magnetic state is essential for high-performance operation. The saturation effect related to the cross-saturation has to be taken carefully into account in order to achieve the desired operation. Two prototype machines have been designed and built for testing: one totally enclosed machine with a special magnet module pole arrangement and another through-ventilated machine with a more traditional embedded magnet structure. Both structures are built with magnetically salient structures in order to increase the torque production capability with the reluctance torque component. Both machine structures show potential for traction usage. However, the traditional embedded magnet design turns out to be mechanically the more secure one of these two machine options.

Energy Efficiency Consideration in Electric Vehicle Transmission

This study is a survey of benefits and drawbacks of embedding a variable gearbox instead of a single reduction gear in electric vehicle powertrain from efficiency point of view. Losses due to a pair of spur gears meshing with involute teeth are modeled on the base of Coulomb’s law and fluid mechanics. The model for a variable gearbox is fulfilled and further employed in a complete vehicle simulation. Simulation model run for a single reduction gear then the results are taken as benchmark for other types of commonly used transmissions. Comparing power consumption, which is obtained from simulation model, shows that the extra load imposed by variable transmission components will shade the benefits of efficient operation of electric motor. The other accomplishment of this study is a combination of modified formulas that led to a new methodology for power loss prediction in gear meshing which is compatible with modern design and manufacturing technology.

The effects of location, feedstock availability, and supply-chain logistics on the greenhouse gas emissions of forest-biomass energy utilization in Finland

Forest biomass represents a geographically distributed feedstock, and geographical location affects the greenhouse gas (GHG) performance of a given forest-bioenergy system in several ways. For example, biomass availability, forest operations, transportation possibilities and the distances involved, biomass end-use possibilities, fossil reference systems, and forest carbon balances all depend to some extent on location. The overall objective of this thesis was to assess the GHG emissions derived from supply and energy-utilization chains of forest biomass in Finland, with a specific focus on the effect of location in relation to forest biomass’s availability and the transportation possibilities. Biomass availability and transportation-network assessments were conducted through utilization of geographical information system methods, and the GHG emissions were assessed by means of lifecycle assessment. The thesis is based on four papers in which forest biomass supply on industrial scale was assessed. The feedstocks assessed in this thesis include harvesting residues, smalldiameter energy wood and stumps. The principal implication of the findings in this thesis is that in Finland, the location and availability of biomass in the proximity of a given energyutilization or energy-conversion plant is not a decisive factor in supply-chain GHG emissions or the possible GHG savings to be achieved with forest-biomass energy use. Therefore, for the greatest GHG reductions with limited forest-biomass resources, energy utilization of forest biomass in Finland should be directed to the locations where most GHG savings are achieved through replacement of fossil fuels. Furthermore, one should prioritize the types of forest biomass with the lowest direct supply-chain GHG emissions (e.g., from transport and comminution) and the lowest indirect ones (in particular, soil carbon-stock losses), regardless of location. In this respect, the best combination is to use harvesting residues in combined heat and power production, replacing peat or coal.

Advances in modelling of mechatronic systems: the toolset FASIM_C++ for the simulation of vehicle dynamics

The increasing complexity of controller systems, applied in modern passenger cars, requires adequate simulation tools. The toolset FASIM_C++, described in the following, uses complex vehicle models in three-dimensional vehicle dynamics simulation. The structure of the implemented dynamic models and the generation of the equations of motion applying the method of kinematic differentials is explained briefly. After a short introduction in methods of event handling, several vehicle models and applications like controller development, roll-over simulation and real-time-simulation are explained. Finally some simulation results are presented.