Comparison of particle number concentrations between different environments

Particle number concentrations vary significantly with environment and, in this study, we attempt to assess the significance of these differences. Towards this aim, we reviewed 85 papers that have reported particle number concentrations levels at 126 sites covering different environments. We grouped the results into eight categories according to measurement location including: road tunnel, on-road, road-side, street canyon, urban, urban background, rural, and clean background. Median values were calculated for each category. This review was restricted to papers that presented concentrations numerically. The majority of the reports were based on either CPC or SMPS measurements, with a limited number of papers reporting results from both instruments at the same site. Hence there were several overlaps between the number of CPC and SMPS measuring sites. Most of the studies reported multiple measurements at a given study site, while some studies included results from more than one site. From these reports, the overall median value for each location category was calculated...

Better cars or older cars?: Assessing CO2 emission reduction potential of passenger vehicle replacement programs

The primary motivation for the vehicle replacement schemes that were implemented in many countries was to encourage the purchase of new cars. The basic assumption of these schemes was that these acquisitions would benefit both the economy and the environment as older and less fuel-efficient cars were scrapped and replaced with more fuel-efficient models. In this article, we present a new environmental impact assessment method for assessing the effectiveness of scrappage schemes for reducing CO2 emissions taking into account the rebound effect, driving behavior for older versus new cars and entire lifecycle emissions for during the manufacturing processes of new cars. The assessment of the Japanese scrappage scheme shows that CO2 emissions would only decrease if users of the scheme retained their new gasoline passenger vehicles for at least 4.7 years. When vehicle replacements were restricted to hybrid cars, the reduction in CO2 achieved by the scheme would be 6-8.5 times higher than the emissions resulting from a scheme involving standard, gasoline passenger vehicles. Cost-benefit analysis, based on the emission reduction potential, showed that the scheme was very costly. Sensitivity analysis showed that the Japanese government failed to determine the optimum, or target, car age for scrapping old cars in the scheme. Specifically, scrapping cars aged 13 years and over did not maximize the environmental benefits of the scheme. Consequently, modifying this policy to include a reduction in new car subsidies, focused funding for fuel-efficient cars, and modifying the target car age, would increase environmental benefits. © 2013 Elsevier Ltd.

On the effectiveness of a license scheme for E-waste recycling : the challenge of China and India

It is well known that China and India have been recycling centers of WEEE, especially printed circuit boards, and that serious environmental pollution in these countries has been generated by improper recycling methods. After the governments of China and India banned improper recycling by the informal sector, improper recycling activities spread to other places. Then, these governments changed their policies to one of promoting proper recycling by introducing a scheme, under which E-waste recycling requires a license issued by the government. In this paper, the effectiveness of that license scheme is examined by means of an economic model. It can be shown that the license scheme can work effectively only if disposers of E-waste have a responsibility to sell E-waste to license holders. Our results run counter to the idea that international E-waste trade should be banned and provide an alternative solution to the problem.

Reshaping housing using prefabricated systems

Prefabricated housing innovations have the potential to reduce the environmental impact of construction through improvements to efficiency and quality. The current paper presents a number of recommendations for increasing the adoption of prefabrication based on a review of published evidence. The recommendations consider multiple stakeholders including builders and other intermediaries, suppliers, end-users, as well as their interaction with the broader policy context and technical issues

Sustainable innovation for Queensland’s housing design : a case study

This research provides an assessment tool that assists the selection process of sustainability in detached suburban housing. It investigates the implications of using different design and construction methods including architecturally designed houses, developer housing and prefabricated houses. The study simulates one example of the three types of houses that have been chosen to fulfil a real client brief on a real site on the Sunshine Coast, Queensland Australia. Criteria for sustainability assessment are formulated based on literature reviews, exemplar designs and similar research projects for which the houses can be adequately evaluated. This criterion covers aspects including energy use, materials and thermal performance. The data is collected using computer models and sustainability assessment software to compare and draw conclusions on the success of each house. Our study indicates that architecturally designed housing with prefabricated building techniques are a better alternative to generic developer style housing. Our research provides an insight into the implications of three key elements of sustainability including energy use, materials and thermal performance. Designers, builders, developers and home-buyers are given an insight into some options currently available on the housing market and how the choices made during early design stages can provide a more positive environmental impact.

Community environment education centers : Facilitating community created ecoscapes

This study focuses on designing a community environment education center (CEEC) for Chillingham, as a hub for community transition to sustainability, redressing social fragmentation, youth unemployment, a high eco-footprint and economic rural decline due to globalisation. The ecologically sustainable development framework was delivered by integrating environment education and community development through project-based experiential learning. The development of Chillingham Community Centre involved case study research and incorporated participatory design charrettes, transformative learning, eco-positive development and community-public-private partnerships. This process evolved from community strategic planning in a small rural village buffering world heritage rainforests impacted by a rapidly expanding urban conurbation on Australia’s east coast. This community space encompasses socio-environmental flows connecting people to each other and the ecoscape to grow natural capital, community cohesion and empower eco-governance. Modelling passive solar design, on-site renewable energy/water/nutrient cycling, community garden/market and environment education programs sowed the seeds for a green local economy, demonstrating community capacity to participate in transition to sustainability. A small rural community can demonstrate to other communities that a CEEC enables people to meet their socio-environmental and economic needs locally and sustainably. The ecologically sustainable solution is holistic, all settlements need to be richly biodiverse, locally specific and globally wise.

Reshaping housing : the role of prefabricated systems

Prefabricated housing innovations have the potential to reduce the environmental impact of construction through improving efficiency and quality. The current paper systematically summarises the published evidence since 1990 that describes the barriers and drivers affecting the uptake of prefabricated housing innovations. These are discussed in relation to a ‘Project-Based Product Framework’ which considers multiple stakeholders including builders and other intermediaries, suppliers, end-users, the broader policy context and technical issues. The framework facilitated identification of central issues such as the prevalent business and cultural resistance associated with process changes; the potential for efficiency and quality improvements and cost savings; the simultaneous risks and benefits of close supplier-builder relationships, and negative user perceptions towards prefabricated houses. Though there is a lack of evidence regarding the effects of regulations and government policies on prefabrication uptake, there are indications of the positive potential of financial and social incentives. Directions for further research include understanding how to: manage the industry’s transition to prefabricated houses; appropriately compare prefabricated housing to traditional housing on cost, efficiency and quality measures; reconcile the differing perspectives of various stakeholders; quantify and identify the perspectives of the potential end-user population, and manage the interface between the emerging industry and information technology improvements.

Microalgal biomass as a fermentation feedstock for bioethanol production

BACKGROUND The increasing cost of fossil fuels as well as the escalating social and industrial awareness of the environmental impacts associated with the use of fossil fuels has created the need for more sustainable fuel options. Bioethanol, produced from renewable biomass such as sugar and starch materials, is believed to be one of these options, and it is currently being harnessed extensively. However, the utilization of sugar and starch materials as feedstocks for bioethanol production creates a major competition with the food market in terms of land for cultivation, and this makes bioethanol from these sources economically less attractive. RESULT This study explores the suitability of microalgae (Chlorococum sp.) as a substrate for bioethanol production via yeast (Saccharomycesbayanus)under different fermentation conditions. Results show a maximum ethanol concentration of 3.83 g L -1 obtained from 10 g L-1 of lipid-extracted microalgae debris. CONCLUSION This productivity level (∼38% w/w), which is in keeping with that of current production systems endorses microalgae as a promising substrate for bioethanol production.

Someone else's boom but always our bust: Australia as a derivative economy, implications for regions

This paper examines the socio-economic impact of mineral and agricultural resource extraction on local communities and explores policy options for addressing them. An emphasis on the marketisation of services together with tight fiscal control has reinforced decline in many country communities in Australia and elsewhere. However, the introduction by the European Union of Regional Policy which emphasises ‘smart specialisation’ can enhance greatly the capacity of local people to generate decent livelihoods. For this to have real effect, the innovative state has to enable partnerships between communities, researchers and industry. For countries like Australia, this would be a substantive policy shift.

Residents’ experiences of privacy and comfort in multi-storey apartment dwellings in subtropical Brisbane

Dwellings in multi-storey apartment buildings (MSAB) are predicted to increase dramatically as a proportion of housing stock in subtropical cities over coming decades. The problem of designing comfortable and healthy high-density residential environments and minimising energy consumption must be addressed urgently in subtropical cities globally. This paper explores private residents’ experiences of privacy and comfort and their perceptions of how well their apartment dwelling modulated the external environment in subtropical conditions through analysis of 636 survey responses and 24 interviews with residents of MSAB in inner urban neighbourhoods of Brisbane, Australia. The findings show that the availability of natural ventilation and outdoor private living spaces play important roles in resident perceptions of liveability in the subtropics where the climate is conducive to year round “outdoor living”. Residents valued choice with regard to climate control methods in their apartments. They overwhelmingly preferred natural ventilation to manage thermal comfort, and turned to the air-conditioner for limited periods, particularly when external conditions were too noisy. These findings provide a unique evidence base for reducing the environmental impact of MSAB and increasing the acceptability of apartment living, through incorporating residential attributes positioned around climate-responsive architecture.

Eating for health and the environment: Australian regulatory responses for dietary change

The Australian food system significantly contributes to a range of key environmental issues including harmful greenhouse gas emissions, air pollution, soil desertification, biodiversity loss and water scarcity. At the same time, the Australian s food system is a key cause of public health nutrition issues that stem from the co-existence of over- and under-consumption of dietary energy and nutrients. Within these challenges lie synergies and opportunities because a diet that has a lower environmental impact generally aligns with good nutrition. Australian State and Federal initiatives to influence food consumption patterns focus on individual body weight and ‘soft law’ interventions. These regulatory approaches, by focusing on select symptoms of food system failures, are fragmented, reductionist and inefficient. In order to illustrate this point, this paper will explore Australian regulatory responses to diet-related illnesses. The analysis will support the argument that only when regulatory responses to diets become embedded within reform of the current food system will substantial improvements to human and planetary health be achieved.

The future of roads: How road agencies are facing a conflicted future

Although road construction and use provides significant economic and social benefits, its environmental impact is of growing concern. Roads are one of the greatest greenhouse gas contributors, both directly through fossil energy consumed in mining, transporting, earthworks and paving work, and through the emissions from road use by vehicles. Further,according to the Australian Government, when combined with expected population growth and internal migration,expected changes in temperature and rainfall are expected to increase road maintenance costs. This discussion paper will outline opportunities within the Australian context for reducing environmental and carbon pressure from road building, and provide a framework for considering the potential pressures that will affect the resilience of roads to the impacts of climate change and oil vulnerability.

Modelling of Electric Fields

South Africa has an electrical transmission grid of over 25 000 km of overhead power lines with voltages of 132 kV to 765 kV. The grid has been largely designed and built by the power utility, Eskom. This book embodies the planning philosophies, design principles and construction practices of Eskom. It is the culmination of decades of thought, study, research and the practical experience of many overhead power line engineers and researchers. The book covers the main aspects of overhead power line design and construction, from electrical first principles, system planning, insulation co-ordination (including live line working), mechanical design through to environmental impact management and power line communications. The content emphasises the need for close interaction between all technical disciplines involved and the importance of optimising designs for economy and performance. Additional challenges in South Africa are the relatively high altitude of the interior plateau (1 000 m to 1 700 m above sea level), severe lightning in some areas and long transmission distances. The book explains how these factors are accommodated in modern designs. Other advanced work covered includes the use and understanding of polymeric insulators, the judicious reduction of phase-to-phase spacings and the adoption of guyed structures.

Hampson type heat-exchanger technology and economic evaluation for LNG re- gasification and power generation At LNG receiving terminals

The system for high utilization of LNG cold energy is proposed by use of process simulator. The proposed design is a closed loop system, and composed by a Hampson type heat exchanger, turbines, pumps and advanced humid air turbine (AHAT) or Gas turbine combined cycle (GTCC). Its heat sources are Boil-off gas and cooling water for AHAT or GTCC. The higher cold exergy recovery to power can be about 38 to 56% as compared to the existing cold power generation of about 20% with a Rankine cycle of a single component. The advantage of the proposed system is to reduce the number of heat exchangers. Furthermore, the environmental impact is minimized because the proposed design is a closed loop system. A life cycle comparative cost is calculated to demonstrate feasibility of the proposed design. The development of the Hampson type exchangers is expected to meet the key functional requirements and will result in much higher LNG cold exergy recovery and the overall system performance i.e. re-gasification. Additionally, the proposed design is expected to provide flexibility to meet different gas pressure suited for the deregulation of energy system in Japan and higher reliability for an integrated boil-off gas system.

Understanding coal seam gas associated water, regulations and strategies for treatment

The coal seam gas (CSG) industry is globally of potentially great importance economically. This study exemplifies the complex relationship between land use and management, groundwater impact and associated water treatment especially in relation to Queensland where a significant increase in the amount of gas extracted over the past 6 years has occurred. In order to effectively manage the environmental impact of the CSG industry it is necessary to appropriately understand the nature of the gas deposits, methods for gas collection, the physicochemical composition of the by-product associated water and the technologies available for water remediation. Australia is mainly considered arid and semi-arid and thus there is a need to not only beneficially reuse water resources but also protect existing ground water reservoirs such as the Great Artesian Basin (GAB). This paper focussed primarily on the Surat Basin located in Queensland and northern New South Wales. The mechanism for CSG formation, relation to local geological features, extraction approach and the potential impact/benefits of associated water was discussed. An outline of the current legislative requirements on physical and chemical properties of associated water in the Surat Basin was also provided, as well as the current treatment technologies used by the major CSG companies. This review was of significance in relation to the formulation of the most appropriate and cost effective management of associated water, while simultaneously preserving existing water resources and the environment.