Exploring molecular recognition pathways in one- and two-component gels formed by dendritic lysine-based gelators

This paper provides an integrated overview of the factors which control gelation in a family of dendritic gelators based on lysine building blocks. In particular, we establish that higher generation systems are more effective gelators, amide linkages in the dendron are better than carbamates, and long alkyl chain surface groups and a carboxylic acid at the focal point enhance gelation. The gels are best formed in relatively low polarity solvents with no hydrogen bond donor ability and limited hydrogen bond acceptor capacity. The dendrons with acid groups at the focal point can form two component gels with diaminododecane, and in this case, it is the lower generation dendrons which can avoid steric hindrance and form more effective gels. The stereochemistry of lysine is crucial in self-assembly, with opposite enantiomers disrupting each other's molecular recognition pathways. For the two-component system, stoichiometry is key, if too much diamine is present, dendron-stabilised microcrystals of the diamine begin to form. Interestingly, gelation still occurs in this case, and the systems with amides/alkyl chains are more effective gels, as a consequence of enhanced dendron-dendron intermolecular interactions allowing the microcrystals to form an interconnected network.

Controlling the materials properties and nanostructure of a single-component dendritic gel by adding a second component

This paper reports a dendritic system which is capable of forming both one-component and two-component gels interestingly the addition of the second component can either increase or decrease the degree of gelation, depending on dendritic generation.

Optimal wafer site selection using forward selection component analysis

Reducing wafer metrology continues to be a major target in semiconductor manufacturing efficiency initiatives due to it being a high cost, non-value added operation that impacts on cycle-time and throughput. However, metrology cannot be eliminated completely given the important role it plays in process monitoring and advanced process control. To achieve the required manufacturing precision, measurements are typically taken at multiple sites across a wafer. The selection of these sites is usually based on a priori knowledge of wafer failure patterns and spatial variability with additional sites added over time in response to process issues. As a result, it is often the case that in mature processes significant redundancy can exist in wafer measurement plans. This paper proposes a novel methodology based on Forward Selection Component Analysis (FSCA) for analyzing historical metrology data in order to determine the minimum set of wafer sites needed for process monitoring. The paper also introduces a virtual metrology (VM) based approach for reconstructing the complete wafer profile from the optimal sites identified by FSCA. The proposed methodology is tested and validated on a wafer manufacturing metrology dataset. © 2012 IEEE.

Elements of A New Framework for the principle of Equal Treatment of persons in EC Law

In June and November 2000, the European Parliament and the Council adopted two Directives referring to ‘the principle of equal treatment irrespective of’ in their title, one relating to racial and ethnic origin, the other to disability, age, religion and belief or sexual orientation. A thorough reform of Directive 76/207/EEC on the principle of equal treatment for women and men in employment matters is pending between the European Parliament's second reading and adoption while this is written. Community secondary legislation on equal treatment of persons has thus expanded in scope and number of reasons which must not serve as starting points for differentiation. Does this signify progress in legal protection against personal discrimination? While not providing a ready answer, this article proposes an analytical framework to answer this question, concentrating on conceptions of equality in general and in particular on the problems multi-dimensional discrimination might pose for the law.

Optimisation of a two-liquid component pre-filled acrylic bone cement system: A design of experiments approach to optimise cement final properties

The initial composition of acrylic bone cement along with the mixing and delivery technique used can influence its final properties and therefore its clinical success in vivo. The polymerisation of acrylic bone cement is complex with a number of processes happening simultaneously. Acrylic bone cement mixing and delivery systems have undergone several design changes in their advancement, although the cement constituents themselves have remained unchanged since they were first used. This study was conducted to determine the factors that had the greatest effect on the final properties of acrylic bone cement using a pre-filled bone cement mixing and delivery system. A design of experiments (DoE) approach was used to determine the impact of the factors associated with this mixing and delivery method on the final properties of the cement produced. The DoE illustrated that all factors present within this study had a significant impact on the final properties of the cement. An optimum cement composition was hypothesised and tested. This optimum recipe produced cement with final mechanical and thermal properties within the clinical guidelines and stated by ISO 5833 (International Standard Organisation (ISO), International standard 5833: implants for surgery—acrylic resin cements, 2002), however the low setting times observed would not be clinically viable and could result in complications during the surgical technique. As a result further development would be required to improve the setting time of the cement in order for it to be deemed suitable for use in total joint replacement surgery.

Nonequilibrium Quantum Landauer Principle

Using the operational framework of completely positive, trace preserving operations and thermodynamic fluctuation relations, we derive a lower bound for the heat exchange in a Landauer erasure process on a quantum system. Our bound comes from a nonphenomenological derivation of the Landauer principle which holds for generic nonequilibrium dynamics. Furthermore, the bound depends on the nonunitality of dynamics, giving it a physical significance that differs from other derivations. We apply our framework to the model of a spin-1/2 system coupled to an interacting spin chain at finite temperature.