MODELING ELECTRODIALYSIS AND A PHOTOCHEMICAL PROCESS FOR THEIR INTEGRATION IN SALINE WASTEWATER TREATMENT

Oxidation processes can be used to treat industrial wastewater containing non-biodegradable organic compounds. However, the presence of dissolved salts may inhibit or retard the treatment process. In this study, wastewater desalination by electrodialysis (ED) associated with an advanced oxidation process (photo-Fenton) was applied to an aqueous NaCl solution containing phenol. The influence of process variables on the demineralization factor was investigated for ED in pilot scale and a correlation was obtained between the phenol, salt and water fluxes with the driving force. The oxidation process was investigated in a laboratory batch reactor and a model based on artificial neural networks was developed by fitting the experimental data describing the reaction rate as a function of the input variables. With the experimental parameters of both processes, a dynamic model was developed for ED and a continuous model, using a plug flow reactor approach, for the oxidation process. Finally, the hybrid model simulation could validate different scenarios of the integrated system and can be used for process optimization.

Batch Liquid-Liquid Extraction of Phenol from Aqueous Solutions

The aim of this work is the study of batch liquid-liquid extraction of phenol from aqueous solutions in a bench-scale well-mixed reactor. The influence of the ratio of phase volumes, temperature, and rotational speed on phenol removal (0.72-1.1% w/w) was investigated using methyl isobutyl ketone as an extracting solvent. For this purpose, the ratio of phase volumes were set at 0.1 and 0.2, the temperature at 10, 20, and 30 degrees C, and the rotational speed at 300, 400, and 500 rpm. A physical model based on the material balance of the phases as well as the equation of mass flux between the phases allowed the estimation of the overall coefficient of mass transfer coupled with the superficial area. Moreover, it proved to fit, satisfactorily well, the experimental data of residual phenol concentration in the organic phase versus time under all the conditions investigated.

Infinite horizon MPC with non-minimal state space feedback

In the MPC literature, stability is usually assured under the assumption that the state is measured. Since the closed-loop system may be nonlinear because of the constraints, it is not possible to apply the separation principle to prove global stability for the Output feedback case. It is well known that, a nonlinear closed-loop system with the state estimated via an exponentially converging observer combined with a state feedback controller can be unstable even when the controller is stable. One alternative to overcome the state estimation problem is to adopt a non-minimal state space model, in which the states are represented by measured past inputs and outputs [P.C. Young, M.A. Behzadi, C.L. Wang, A. Chotai, Direct digital and adaptative control by input-output, state variable feedback pole assignment, International journal of Control 46 (1987) 1867-1881; C. Wang, P.C. Young, Direct digital control by input-output, state variable feedback: theoretical background, International journal of Control 47 (1988) 97-109]. In this case, no observer is needed since the state variables can be directly measured. However, an important disadvantage of this approach is that the realigned model is not of minimal order, which makes the infinite horizon approach to obtain nominal stability difficult to apply. Here, we propose a method to properly formulate an infinite horizon MPC based on the output-realigned model, which avoids the use of an observer and guarantees the closed loop stability. The simulation results show that, besides providing closed-loop stability for systems with integrating and stable modes, the proposed controller may have a better performance than those MPC controllers that make use of an observer to estimate the current states. (C) 2008 Elsevier Ltd. All rights reserved.

USE OF SOLAR ENERGY IN THE TREATMENT OF WATER CONTAMINATED WITH PHENOL BY PHOTOCHEMICAL PROCESSES

The solar driven photo-Fenton process for treating water containing phenol as a contaminant has been evaluated by means of pilot-scale experiments with a parabolic trough solar reactor (PTR). The effects of Fe(II) (0.04-1.0 mmol L(-1)), H(2)O(2) (7-270 mmol L(-1)), initial phenol concentration (100 and 500 mg C L(-1)), solar radiation, and operation mode (batch and fed-batch) on the process efficiency were investigated. More than 90% of the dissolved organic carbon (DOC) was removed within 3 hours of irradiation or less, a performance equivalent to that of artificially-irradiated reactors, indicating that solar light can be used either as an effective complementary or as an alternative source of photons for the photo-Fenton degradation process. A non-linear multivariable model based on a neural network was fit to the experimental results of batch-mode experiments in order to evaluate the relative importance of the process variables considered on the DOC removal over the reaction time. This included solar radiation, which is not a controlled variable. The observed behavior of the system in batch-mode was compared with fed-batch experiments carried out under similar conditions. The main contribution of the study consists of the results from experiments under different conditions and the discussion of the system behavior. Both constitute important information for the design and scale-up of solar radiation-based photodegradation processes.

Piezoresistive response of ITO films deposited at room temperature by magnetron sputtering

Indium tin oxide (ITO) thin films have been deposited on (100) Si substrates by RF magnetron sputtering from a compact target (90% In(2)O(3)-10% SnO(2) in weight) with 6 in. in diameter. In order to perform electromechanical characterizations of these films, strain gauges were fabricated. An experimental set-up based on bending beam theory was developed to determine the longitudinal piezoresistive coefficient (pi(1)) of the strain gauges fabricated. It has been confirmed that electrical resistance of the strain gauges decreases with load increases which results a negative gauge factor. A model based on the activation energy was used to explain the origin of this negative signal. The influence of the temperature on piezoresistive properties of ITO films was also evaluated.

The generalized inverse Weibull distribution

The inverse Weibull distribution has the ability to model failure rates which are quite common in reliability and biological studies. A three-parameter generalized inverse Weibull distribution with decreasing and unimodal failure rate is introduced and studied. We provide a comprehensive treatment of the mathematical properties of the new distribution including expressions for the moment generating function and the rth generalized moment. The mixture model of two generalized inverse Weibull distributions is investigated. The identifiability property of the mixture model is demonstrated. For the first time, we propose a location-scale regression model based on the log-generalized inverse Weibull distribution for modeling lifetime data. In addition, we develop some diagnostic tools for sensitivity analysis. Two applications of real data are given to illustrate the potentiality of the proposed regression model.

PROPOSAL OF A PERFORMANCE MEASURING SYSTEM APPLIED TO AGRICULTURAL MECHANIZATION

The leaders` organizations of several different sectors have as characteristic to measure their own performance in a systematic way. However, this concept is still unusual in agricultural enterprises, including the mechanization sector. Mechanization has an important role on the production costs and to know its performance is a key factor for the agricultural enterprise success. This work was generated by the importance that measurement of performance has for the management and the mechanization impact on the production costs. Its aim is to propose an integrated performance measurement system to give support to agricultural management. The methodology was divided in two steps: adjustment of a conceptual model based on Balanced Score Card - BSC; application of the model in a study case at sugar cane mill. The adjustment and the application of the conceptual model allowed to obtain the performance index in a systematic way, that are associated to: costs and deadline ( traditionally used); control and improvement on the quality of operations and support process; environmental preservation; safety; health; employees satisfaction; development of information systems. The adjusted model helped the development of the performance measurement system for the mechanized management systems and the index allows an integrated view of the enterprise, related to its strategic objectives.

Development of Ramulosis Disease of Cotton Under Controlled Environment and Field Conditions

Colletotrichum gossypii var. cephalosporioides, the fungus that causes ramulosis disease of cotton, is widespread in Brazil and can cause severe yield loss. Because weather conditions greatly affect disease development, the objective of this work was to develop weather-based models to assess disease favorability. Latent period, incidence, and severity of ramulosis symptoms were evaluated in controlled environment experiments using factorial combinations of temperature (15, 20, 25, 30, and 35 degrees C) and leaf wetness duration (0, 4, 8, 16, 32, and 64 h after inoculation). Severity was modeled as an exponential function of leaf wetness duration and temperature. At the optimum temperature of disease development, 27 degrees C, average latent period was 10 days. Maximum ramulosis severity occurred from 20 to 30 degrees C, with sharp decreases at lower and higher temperatures. Ramulosis severity increased as wetness periods were increased from 4 to 32 h. In field experiments at Piracicaba, Sao Paulo State, Brazil, cotton plots were inoculated (10(5) conidia ml(-1)) and ramulosis severity was evaluated weekly. The model obtained from the controlled environment study was used to generate a disease favorability index for comparison with disease progress rate in the field. Hourly measurements of solar radiation, temperature, relative humidity, leaf wetness duration, rainfall, and wind speed were also evaluated as possible explanatory variables. Both the disease favorability model and a model based on rainfall explained ramulosis growth rate well, with R(2) of 0.89 and 0.91, respectively. They are proposed as models of ramulosis development rate on cotton in Brazil, and weather-disease relationships revealed by this work can form the basis of a warning system for ramulosis development.

A simple data logger for student-designed rocket experiments.

The final-year project for Mechanical & Space Engineering students at UQ often involves the design and flight testing of an experiment. This report describes the design and use of a simple data logger that should be suitable for collecting data from the students' flight experiments. The exercise here was taken as far as the construction of a prototype device that is suitable for ground-based testing, say, the static firing of a hybrid rocket motor.

Growth of Bose-Einstein condensates from thermal vapor

We report on a quantitative study of the growth process of 87Rb Bose-Einstein condensates. By continuous evaporative cooling we directly control the thermal cloud from which the condensate grows. We compare the experimental data with the results of a theoretical model based on quantum kinetic theory. We find quantitative agreement with theory for the situation of strong cooling, whereas in the weak cooling regime a distinctly different behavior is found in the experiment.

In vivo measurement of the effect of intra-abdominal pressure on the human spine

In humans, intra-abdominal pressure (IAP) is elevated during many everyday activities. This experiment aimed to investigate the extent to which increased IAP-without concurrent activity of the abdominal or back extensor muscles-produces an extensor torque. With subjects positioned in side lying on a swivel table with its axis at L3, moments about this vertebral level were measured when IAP was transiently increased by electrical stimulation of the diaphragm via the phrenic nerve. There was no electromyographic activity in abdominal and back extensor muscles. When IAP was increased artificially to similar to 15% of the maximum IAP amplitude that could be generated voluntarily with the trunk positioned in flexion, a trunk extensor moment (similar to6 Nm) was recorded. The size of the effect was proportional to the increase in pressure. The extensor moment was consistent with that predicted from a model based on measurements of abdominal cross-sectional area and IAP moment arm. When IAP was momentarily increased while the trunk was flexed passively at a constant velocity, the external torque required to maintain the velocity was increased. These results provide the first in vivo data of the amplitude of extensor moment that is produced by increased IAP. Although the net effect of this extensor torque in functional tasks would be dependent on the muscles used to increase the IAP and their associated flexion torque, the data do provide evidence that IAP contributes, at least in part, to spinal stability. (C) 2001 Elsevier Science Ltd. All rights reserved.

A numerical study of flexural buckling of foliated rock slopes

The occurrence of foliated rock masses is common in mining environment. Methods employing continuum approximation in describing the deformation of such rock masses possess a clear advantage over methods where each rock layer and each inter-layer interface (joint) is explicitly modelled. In devising such a continuum model it is imperative that moment (couple) stresses and internal rotations associated with the bending of the rock layers be properly incorporated in the model formulation. Such an approach will lead to a Cosserat-type theory. In the present model, the behaviour of the intact rock layer is assumed to be linearly elastic and the joints are assumed to be elastic-perfectly plastic. Condition of slip at the interfaces are determined by a Mohr-Coulomb criterion with tension cut off at zero normal stress. The theory is valid for large deformations. The model is incorporated into the finite element program AFENA and validated against an analytical solution of elementary buckling problems of a layered medium under gravity loading. A design chart suitable for assessing the stability of slopes in foliated rock masses against flexural buckling failure has been developed. The design chart is easy to use and provides a quick estimate of critical loading factors for slopes in foliated rock masses. It is shown that the model based on Euler's buckling theory as proposed by Cavers (Rock Mechanics and Rock Engineering 1981; 14:87-104) substantially overestimates the critical heights for a vertical slope and underestimates the same for sub-vertical slopes. Copyright (C) 2001 John Wiley & Sons, Ltd.

The game to play: expanding the co-opetition proposal through the strategic games matrix

Purpose - Using Brandenburger and Nalebuff`s 1995 co-opetition model as a reference, the purpose of this paper is to seek to develop a tool that, based on the tenets of classical game theory, would enable scholars and managers to identify which games may be played in response to the different conflict of interest situations faced by companies in their business environments. Design/methodology/approach - The literature on game theory and business strategy are reviewed and a conceptual model, the strategic games matrix (SGM), is developed. Two novel games are described and modeled. Findings - The co-opetition model is not sufficient to realistically represent most of the conflict of interest situations faced by companies. It seeks to address this problem through development of the SGM, which expands upon Brandenburger and Nalebuff`s model by providing a broader perspective, through incorporation of an additional dimension (power ratio between players) and three novel, respectively, (rival, individualistic, and associative). Practical implications - This proposed model, based on the concepts of game theory, should be used to train decision- and policy-makers to better understand, interpret and formulate conflict management strategies. Originality/value - A practical and original tool to use game models in conflict of interest situations is generated. Basic classical games, such as Nash, Stackelberg, Pareto, and Minimax, are mapped on the SGM to suggest in which situations they Could be useful. Two innovative games are described to fit four different types of conflict situations that so far have no corresponding game in the literature. A test application of the SGM to a classic Intel Corporation strategic management case, in the complex personal computer industry, shows that the proposed method is able to describe, to interpret, to analyze, and to prescribe optimal competitive and/or cooperative strategies for each conflict of interest situation.

Development Resource Planning: Complexity of Product Development and the Capacity to Launch New Products

Overcommitment of development capacity or development resource deficiencies are important problems in new product development (NPD). Existing approaches to development resource planning have largely neglected the issue of resource magnitude required for NPD. This research aims to fill the void by developing a simple higher-level aggregate model based on an intuitive idea: The number of new product families that a firm can effectively undertake is bound by the complexity of its products or systems and the total amount of resources allocated to NPD. This study examines three manufacturing companies to verify the proposed model. The empirical results confirm the study`s initial hypothesis: The more complex the product family, the smaller the number of product families that are launched per unit of revenue. Several suggestions and implications for managing NPD resources are discussed, such as how this study`s model can establish an upper limit for the capacity to develop and launch new product families.

Transport-Regional Equity Issue Revisited

Almeida E. S. de, Haddad E. A. and Hewings G. J. D. Transport-regional equity issue revisited, Regional Studies. The objective of this paper is to analyse the relationship between transport and regional equity in Minas Gerais, Brazil. Furthermore, the existence of a trade-off between economic performance and regional equity is investigated as well. To do so, the paper develops a spatial computable general equilibrium model based on Brocker and Schneider`s approach of 2002 to implement comparative static analysis, explicitly incorporating iceberg transportation costs. Four activities are modelled, namely production, final demand, transportation and exports. Two production factors are assumed: labour and other factors. The model has 12 domestic regions and three external regions. Four counterfactual experiments are developed based on decreases in transportation costs due to a `distance shortening`. The main findings indicate that if the transport infrastructure improvement is focused only among poor regions, the promotion of regional equity is insignificant. If the transport infrastructure improvement links are concentrated among rich regions, there is an increase in regional income inequalities. However, if the improvements are targeted to the roads linking poor regions and rich ones, there is greater promotion of regional equity. The same result will occur when improvements are made to all road links of the state. [image omitted] Almeida E. S. de, Haddad E. A. et Hewings G. J. D. La question du rapport entre le transport et l`equilibre regional vue sous un jour nouveau, Regional Studies. Cet article cherche a analyser le rapport entre le transport et l`equilibre regional en Minas Gerais au Bresil. En outre, on examine la presence d`un echange entre la performance economoique et l`equilibre regional. Pour le faire, on construit un modele geographique de l`equilibre general a utiliser sur ordinateur fonde sur l`approche de Brockner et Schneider en 2002 afin de mettre en oeuvre une analyse statique comparative qui comprend explicitement les frais de transport iceberg. On modelise quatre activites, a savoir, la production, la demande finale, le transport et l`exportation. On fait deux suppositions quant aux facteurs de production: la main-d`oevre et d`autres facteurs. Le modele embrasse douze regions internes et trois regions externes. On fait quatre experiences paradoxales fondees sur la baisse des frais de transport due a une `reduction des distances`. Les principaux resultats indiquent que si l`amelioration de l`equipement de transport ne porte que sur les regions defavorisees, la promotion de l`equilibre regional s`avere negligeable. Si l`amelioration de l`equipement de transport focalise les regions riches, il s`avere un creusement des ecarts des revenus regionaux. Cependant, si les ameliorations ciblent les routes qui relient les regions defavorisees aux regions riches, il s`avere une plus grande promotion de l`equilibre regional. Il en va de meme pour la situation ou on a apporte des amenagements a toutes les liaisons routieres de l`etat. Modele geographique de l`equilibre general a utiliser sur ordinateur Equilibre regional Peformance economique Frais de transport Almeida E. S. de, Haddad E. A. und Hewings G. J. D. Die Wiederaufnahme der Frage von Verkehrswesen im Verhaltnis zu regionaler Fairness, Regional Studies. Dieser Aufsatz beabsichtigt, die Beziehung zwischen Verkehrswesen und regionaler Fairness in Minas Gerais (Brasilien) zu analysieren und zugleich auch das Vorkommen von Einbussen entweder bei wirtschaftlicher Leistung der regionaler Fairness zu untersuchen. Zu diesem Zwecke wird ein auf dem Ansatz von Brocker und Schneider (2002) aufbauendes raumliches komputables allgemeines Gleichgewichtsmodell entwickelt, um vergleichende statistische Analysen durchzufuhren, wobei verborgene `Eisberg`-Transportkosten ausdrucklich berucksichtigt werden. Es werden vier Unternehmenstatigk eiten aufgefuhrt: Herstellung, Nachfrage, Transportwesen und Exporte, und zwei Produktionsfaktoren vorausgesetzt: Arbeitskrafte und andere Faktoren. Das Modell umfasst zwolf Inlandsregionen und drei externe Regionen. Es werden vier gegensatzliche Experimente entwickelt, die auf einer Abnahme der Transportkosten infolge einer `Verkurzung der Entfernungen` beruhen. Die Hauptbefunde weisen darauf hin, dass die Forderung regionaler Fairness unbedeutend bleibt, wenn die Verbesserungen der Transportinfrastruktur sich nur auf minderbemittelte Regionen konzentrieren; werden die Verbesserungen der Verbindungen der Transportinfrastruktur in wohlhabenden Regionen durchgefuhrt, so nehmen regionale Einkommensunterschiede zu. Wenn die Verbesserungen jedoch auf Strassen abzielen, die wohlhabende Regionen mit weniger bemittelten verbinden, wird regionale Fairness starker gefordert. Das gleiche Ergebnis wird sich einstellen, wenn Verbesserungen an allen Strassenverbindungen des Staates vorgenommen werden. Raumliches, komputables, allgemeines Gleichgewichtsmodell Regionale Fairness Wirtschaftsleistung Transportkosten Almeida E. S. de, Haddad E. A. y Hewings G. J. D. Revisando el tema de la igualdad del transporte en las regiones, Regional Studies. El objetivo de este documento es analizar la relacion entre el transporte y la igualdad regional en Minas Gerais, Brasil. Asimismo investigamos la existencia de una compensacion entre el rendimiento economico y la igualdad regional. Para ello desarrollamos un modelo de equilibrio general computable y espacial basado en el enfoque de Brocker y Schneider en 2002 para hacer un analisis estatico y comparativo, explicitamente incorporando los costes ocultos de transporte. Se modelan cuatro actividades: la produccion, la demanda final, el transporte y las exportaciones. Suponemos que existen dos factores de produccion: mano de obra y otros factores. En este modelo, existen doce regiones internas y tres regiones externas. Desarrollamos cuatro experimentos contrafactuales basados en la disminucion de los costes de transporte debido a una `acortamiento de las distancias`. Los principales resultados indican que si la mejora de la infraestructura del transporte se centra solo entre las regiones mas pobres, el fomento de la igualdad regional es insignificante. Si los enlaces de la mejora de la infraestructura del transporte se concentran en las regiones ricas, aumentan las desigualdades de ingresos regionales. Sin embargo, si se mejoran los enlaces de carreteras entre las regiones pobres y ricas, se fomenta mejor la igualdad regional. El mismo resultado ocurre cuando se mejoran los enlaces de todas las carreteras del estado. Modelo de equilibrio general computable y espacial Igualdad regional Rendimiento economico Costes de transporte.