Modeling of a Heat-Induced Buckling of Plates Using the Mesh-free Method

In the process of engineering design of structural shapes, the flat plate analysis results can be generalized to predict behaviors of complete structural shapes. In this case, the purpose of this project is to analyze a thin flat plate under conductive heat transfer and to simulate the temperature distribution, thermal stresses, total displacements, and buckling deformations. The current approach in these cases has been using the Finite Element Method (FEM), whose basis is the construction of a conforming mesh. In contrast, this project uses the mesh-free Scan Solve Method. This method eliminates the meshing limitation using a non-conforming mesh. I implemented this modeling process developing numerical algorithms and software tools to model thermally induced buckling. In addition, convergence analysis was achieved, and the results were compared with FEM. In conclusion, the results demonstrate that the method gives similar solutions to FEM in quality, but it is computationally less time consuming.

Semi-automatic parallelisation of unstructured mesh codes

The availability of CFD software that can easily be used and produce high efficiency on a wide range of parallel computers is extremely limited. The investment and expertise required to parallelise a code can be enormous. In addition, the cost of supercomputers forces high utilisation to justify their purchase, requiring a wide range of software. To break this impasse, tools are urgently required to assist in the parallelisation process that dramatically reduce the parallelisation time but do not degrade the performance of the resulting parallel software. In this paper we discuss enhancements to the Computer Aided Parallelisation Tools (CAPTools) to assist in the parallelisation of complex unstructured mesh-based computational mechanics codes.

Software tools for automating the parallelisation of FORTRAN computational mechanics codes

It is now clear that the concept of a HPC compiler which automatically produces highly efficient parallel implementations is a pipe-dream. Another route is to recognise from the outset that user information is required and to develop tools that embed user interaction in the transformation of code from scalar to parallel form, and then use conventional compilers with a set of communication calls. This represents the key idea underlying the development of the CAPTools software environment. The initial version of CAPTools is focused upon single block structured mesh computational mechanics codes. The capability for unstructured mesh codes is under test now and block structured meshes will be included next. The parallelisation process can be completed rapidly for modest codes and the parallel performance approaches that which is delivered by hand parallelisations.

Scalable unstructured mesh decomposition

As the efficiency of parallel software increases it is becoming common to measure near linear speedup for many applications. For a problem size N on P processors then with software running at O(N=P ) the performance restrictions due to file i/o systems and mesh decomposition running at O(N) become increasingly apparent especially for large P . For distributed memory parallel systems an additional limit to scalability results from the finite memory size available for i/o scatter/gather operations. Simple strategies developed to address the scalability of scatter/gather operations for unstructured mesh based applications have been extended to provide scalable mesh decomposition through the development of a parallel graph partitioning code, JOSTLE [8]. The focus of this work is directed towards the development of generic strategies that can be incorporated into the Computer Aided Parallelisation Tools (CAPTools) project.

Appraisal of open software for finite element simulation of 2D metal sheet laser cut.

FEA simulation of thermal metal cutting is central to interactive design and manufacturing. It is therefore relevant to assess the applicability of FEA open software to simulate 2D heat transfer in metal sheet laser cuts. Application of open source code (e.g. FreeFem++, FEniCS, MOOSE) makes possible additional scenarios (e.g. parallel, CUDA, etc.), with lower costs. However, a precise assessment is required on the scenarios in which open software can be a sound alternative to a commercial one. This article contributes in this regard, by presenting a comparison of the aforementioned freeware FEM software for the simulation of heat transfer in thin (i.e. 2D) sheets, subject to a gliding laser point source. We use the commercial ABAQUS software as the reference to compare such open software. A convective linear thin sheet heat transfer model, with and without material removal is used. This article does not intend a full design of computer experiments. Our partial assessment shows that the thin sheet approximation turns to be adequate in terms of the relative error for linear alumina sheets. Under mesh resolutions better than 10e−5 m , the open and reference software temperature differ in at most 1 % of the temperature prediction. Ongoing work includes adaptive re-meshing, nonlinearities, sheet stress analysis and Mach (also called ‘relativistic’) effects.

Aplicación de redes Mesh en el área de videovigilancia y ampliación de zonas Wi-Fi en el municipio de San José las Flores, Chalatenango

El trabajo describe la aplicación de redes Mesh (tecnología inalámbrica) en campos de la videovigilancia y ampliación de zonas Wi-Fi, basado en la realización de una red prototipo capaz de soportar tales servicios, todo esto aplicado al caso de estudio del municipio de San José las Flores, Chalatenango, comunidad de escasos recursos, pues uno de los principales objetivo de este trabajo es hacer accesible esta tecnología a las municipalidades más pobres, para ello se utilizaron herramientas y software libres, dejando plasmado en el documento las factibilidades económicas, técnica y operativa, así como los resultados obtenidos durante la investigación

Development of a Coupling Model for Fluid-Structure Interaction using the Mesh-free Finite Element Method and the Lattice Boltzmann Method

In the presented thesis work, the meshfree method with distance fields was coupled with the lattice Boltzmann method to obtain solutions of fluid-structure interaction problems. The thesis work involved development and implementation of numerical algorithms, data structure, and software. Numerical and computational properties of the coupling algorithm combining the meshfree method with distance fields and the lattice Boltzmann method were investigated. Convergence and accuracy of the methodology was validated by analytical solutions. The research was focused on fluid-structure interaction solutions in complex, mesh-resistant domains as both the lattice Boltzmann method and the meshfree method with distance fields are particularly adept in these situations. Furthermore, the fluid solution provided by the lattice Boltzmann method is massively scalable, allowing extensive use of cutting edge parallel computing resources to accelerate this phase of the solution process. The meshfree method with distance fields allows for exact satisfaction of boundary conditions making it possible to exactly capture the effects of the fluid field on the solid structure.