A high-performance Si-based MOS electrooptic phase modulator with a shunt-capacitor configuration

A novel Si-based metal-oxide-semiconductor (MOS) electrooptic phase modulator including two shunt oxide layer capacitors integrated on a silicon-on-insulator (SOI) waveguide is simulated and analyzed. The refractive index near the two gate oxide layers is modified by the free carrier dispersion effect induced by applying a positive bias on the electrodes. The theoretical calculation of free carrier distribution coupled with optical guided mode propagation characteristics has been carried out. The influence of the structure parameters such as the width and the doping level of the active region are analyzed. A half-wave voltage V-pi = 4 V is demonstrated with an 8-mm active region length and a 4-mu m width of an inner rib under an accumulation mode. When decreasing the inner rib width to 1 mu m, the phase modulation efficiency is even higher, and the rise and fall times reach 50 and 40 ps, respectively, with a 1.0 x 10(17) cm(-3) doping level in the active region.

Evaluation of thermal radiation dependent performance of GaSb thermophotovoltaic cell based on an analytical absorption coefficient model

Applying the model dielectric function method, we have expressed the absorption coefficient of GaSb analytically at room temperature relating to the contribution of various critical points of its electronic band structure. The calculated absorption spectrum shows good agreement with the reported experimental data obtained by spectral ellipsometry on nominally undoped sample. Based on this analytical absorption spectrum, we have qualitatively evaluated the response of active absorbing layer structure and its photoelectric conversion properties of GaSb thermophotovoltaic device on the perturbation of external thermal radiation induced by the varying radiator temperature or emissivity. Our calculation has demonstrated that desirable thickness to achieve the maximum conversion efficiency should be decreased with the increment of radiator temperature and the performance degradation brought by any structure deviation from its optimal one would be stronger meanwhile. For the popular radiator temperature, no more than 1500 K in a real solar thermophotovoltaic system, and typical doping profile in GaSb cell, a reasonable absorbing layer structure parameter should be controlled within 100-300 nm for the emitter while 3000-5000 nm for the base.

Microchip Micellar Electrokinetic Chromatography Based on One Functionalized Ionic Liquid and Its Excellent Performance on Proteins Separation

Herein, one water-soluble functionalized ionic liquid (IL), 1-butyl-3-methylimidazolium dodecanesulfonate (BAS), was designed, investigated and successfully applied to microchip micellar electrokinetic chromatography (MEKC) construction. It possessed the properties of both IL and surfactant. A fairly stable pH value similar to 7.4, which was fit to pH values of general biological buffers, was nicely placed at the optimum concentration of 20 mM BAS solution. While applying BAS solution as running buffer in poly(dimethylsiloxane) (PDMS) microfluidic systems, significantly enhanced electroosmotic flow (8-fold) and resolutions between analytes were obtained than that using other supporting electrolytes or surfactants.

Studies on principal components and antioxidant activity of different Radix Astragali samples using high-performance liquid chromatography/electrospray ionization multiple-stage tandem mass spectrometry

The principal components, isoflavonoids and astragalosides, in the extract of Radix Astragali were detected by a high-performance liquid chromatography Couple to electrospray ionization ion trap multiple-stage tandem mass spectrometry (HPLC-ESI-IT-MSn) method. By comparing the retention time (t(R)) of HPLC, the ESI-MSn data and the structures of analyzed Compounds with the data of reference compounds and in the literature, 17 isoflavonoids and 12 astragalosides have been identified or tentatively deduced. By Virtue of the extracted ion chromatogram (EIC) mode, simultaneous determination of isoflavonoids and astragalosides could be achieved when the different components formed overlapped peaks. And this method has been utilized to analyze the constituents in extracts of Radix Astragali from Helong City and of different growth years. Then the antioxidant activity of different samples has been Successfully investigated by HPLC-ESI-MS method in multiple selected ion monitoring(MIM) mode, applying the spin trapping technology, and the Ferric Reducing Antioxidant Power (FRAP) assay was applied to support the result.

A novel way to enhance electroluminescence performance based on soluble binary and ternary europium 1,1,1-trifluoroacetylacetonate

Five rare earth complexes (Gd(acae)(3), Gd(TFacaC)(3), Eu(acaC)(3), Eu(TFacaC)(3) and Eu(TFacaC)(3)bipy; acac, acetylacetone; TFacac, 1,1,1-trifluoroacetylacetone; bipy, 2,2'-bipyridyl) were synthesized. By comparing the phosphorescence spectra of Gd(acac)(3) and Gd(TFacac)(3) the effect of the replacement of hydrogen by fluorine was examined. Organic light-emitting devices (OLEDs) based on the corresponding europium complexes as emissive layers were also fabricated by the spin-coating method. The triple-layer-type device with the structure glass substrate/ITO (indium-tin oxide)/PVK [poly(N-vinylcarbazole)]/(PVKEu)-Eu-.(TFacac)(3)bipy:PBD[2-(4-bibipyyl)-5-(4-t-butylbipyl-1,3,4-oxadiazole)]/PBD/Al (aluminum) exhibits a brighter red luminescence than those devices with Eu(acac)(3) and Eu(TFacac)(3) complexes as emissive centers upon applying a d.c. voltage.

Assessing the performance of crack detection tests for solder joints

This paper presents both modelling and experimental test data to characterise the performance of four non-destructive tests. The focus is on determining the presence and rough magnitude of thermal fatigue cracks within the solder joints for a surface mount resistor on a strip of FR4 PCB. The tests all operate by applying mechanical loads to the PCB and monitoring the strain response at the top of the resistor. The modelling results show that of the four tests investigated, three are sensitive to the presence of a crack in the joint and its magnitude. Hence these tests show promise in being able to detect cracking caused by accelerated testing. The experimental data supports these results although more validation is required.

Impact of weather conditions on electric vehicle performance

Seasonal and day-to-day variations in travel behaviour and performance of private passenger vehicles can be partially explained by changes in weather conditions. Likewise, in the electricity sector, weather affects energy demand. The impact of weather conditions on private passenger vehicle performance, usership statistics and travel behaviour has been studied for conventional, internal combustion engine, vehicles. Similarly, weather-driven variability in electricity demand and generation has been investigated widely. The aim of these analyses in both sectors is to improve energy efficiency, reduce consumption in peak hours and reduce greenhouse gas emissions. However, the potential effects of seasonal weather variations on electric vehicle usage have not yet been investigated. In Ireland the government has set a target requiring 10% of all vehicles in the transport fleet to be powered by electricity by 2020 to meet part of its European Union obligations to reduce greenhouse gas emissions and increase energy efficiency. This paper fills this knowledge gap by compiling some of the published information available for internal combustion engine vehicles and applying the lessons learned and results to electric vehicles with an analysis of historical weather data in Ireland and electricity market data in a number of what-if scenarios. Areas particularly impacted by weather conditions are battery performance, energy consumption and choice of transportation mode by private individuals.

Applying an XC6200 to real-time image processing

This implementation of a two-dimensional discrete cosine transform demonstrates the development of a suitable architectural style for a specific technology-in this case, the Xilinx XC6200 FPGA series. The design exploits distributed arithmetic, parallelism, and pipelining to achieve a high-performance custom-computing implementation.

Algorithms and architectures for high performance recursive filtering

Recently, a number of most significant digit (msd) first bit parallel multipliers for recursive filtering have been reported. However, the design approach which has been used has, in general, been heuristic and consequently, optimality has not always been assured. In this paper, msd first multiply accumulate algorithms are described and important relationships governing the dependencies between latency, number representations, etc are derived. A more systematic approach to designing recursive filters is illustrated by applying the algorithms and associated relationships to the design of cascadable modules for high sample rate IIR filtering and wave digital filtering.

Systematic methodology for the design of high performance recursive digital filters

A systematic design methodology is described for the rapid derivation of VLSI architectures for implementing high performance recursive digital filters, particularly ones based on most significant digit (msd) first arithmetic. The method has been derived by undertaking theoretical investigations of msd first multiply-accumulate algorithms and by deriving important relationships governing the dependencies between circuit latency, levels of pipe-lining and the range and number representations of filter operands. The techniques described are general and can be applied to both bit parallel and bit serial circuits, including those based on on-line arithmetic. The method is illustrated by applying it to the design of a number of highly pipelined bit parallel IIR and wave digital filter circuits. It is shown that established architectures, which were previously designed using heuristic techniques, can be derived directly from the equations described.

Automated, high performance, flow-through chemiluminescence microarray for the multiplexed detection of phycotoxins

A novel multiplexed immunoassay for the analysis of phycotoxins in shellfish samples has been developed. Therefore, a regenerable chemiluminescence (CL) microarray was established which is able to analyze automatically three different phycotoxins (domoic acid (DA), okadaic acid (OA) and saxitoxin (STX)) in parallel on the analysis platform MCR3. As a test format an indirect competitive immunoassay format was applied. These phycotoxins were directly immobilized on an epoxy-activated PEG chip surface. The parallel analysis was enabled by the simultaneous addition of all analytes and specific antibodies on one microarray chip. After the competitive reaction, the CL signal was recorded by a CCD camera. Due to the ability to regenerate the toxin microarray, internal calibrations of phycotoxins in parallel were performed using the same microarray chip, which was suitable for 25 consecutive measurements. For the three target phycotoxins multi-analyte calibration curves were generated. In extracted shellfish matrix, the determined LODs for DA, OA and STX with values of 0.5±0.3 µg L(-1), 1.0±0.6 µg L(-1), and 0.4±0.2 µg L(-1) were slightly lower than in PBS buffer. For determination of toxin recoveries, the observed signal loss in the regeneration was corrected. After applying mathematical corrections spiked shellfish samples were quantified with recoveries for DA, OA, and STX of 86.2%, 102.5%, and 61.6%, respectively, in 20 min. This is the first demonstration of an antibody based phycotoxin microarray.

The Development and Testing of a New Version of the Cognitive Reflection Test Applying Item Response Theory (IRT)

The cognitive reflection test (CRT) is a short measure of a person's ability to resist intuitive response tendencies and to produce a normatively correct response, which is based on effortful reasoning. Although the CRT is a very popular measure, its psychometric properties have not been extensively investigated. A major limitation of the CRT is the difficulty of the items, which can lead to floor effects in populations other than highly educated adults. The present study aimed at investigating the psychometric properties of the CRT applying item response theory analyses (a two-parameter logistic model) and at developing a new version of the scale (the CRT-long), which is appropriate for participants with both lower and higher levels of cognitive reflection. The results demonstrated the good psychometric properties of the original, as well as the new scale. The validity of the new scale was also assessed by measuring correlations with various indicators of intelligence, numeracy, reasoning and decision-making skills, and thinking dispositions. Moreover, we present evidence for the suitability of the new scale to be used with developmental samples. Finally, by comparing the performance of adolescents and young adults on the CRT and CRT-long, we report the first investigation into the development of cognitive reflection.

Applying gaze-contingent training within community settings to infants from diverse SES backgrounds

Even in infancy children from low-SES backgrounds differ in frontal cortex functioning and, by the start of preschool, they frequently show poor performance on executive functions including attention control. These differences may causally mediate later difficulties in academic learning. Here, we present a study to assess the feasibility of using computerized paradigms to train attention control in infants, delivered weekly over five sessions in early intervention centres for low-SES families. Thirty-three 12-month-old infants were recruited, of whom 23 completed the training. Our results showed the feasibility of repeat-visit cognitive training within community settings. Training-related improvements were found, relative to active controls, on tasks assessing visual sustained attention, saccadic reaction time, and rule learning, whereas trend improvements were found on assessments of short-term memory. No significant improvements were found in task switching. These results warrant further investigation into the potential of this method for targeting ‘at-risk’ infants in community settings.

Rôle des ressources humaines dans la performance du système de référence-évacuation de Kayes au Mali

La mortalité maternelle et périnatale est un problème majeur de santé publique dans les pays en développement. Elle illustre l’écart important entre les pays développés et les pays en développement. Les interventions techniques pour améliorer la santé maternelle et périnatale sont connues dans les pays en développement, mais ce sont la faiblesse des systèmes de santé et les défis liés aux ressources qui freinent leur généralisation. L’objectif principal de ce travail était de mieux comprendre le rôle des ressources humaines en particulier ceux de la première ligne dans la performance d’un système de référence maternelle. Au Mali, la mise en place d’un système de référence maternelle, système de référence-évacuation « SRE », fait partie des mesures nationales de lutte contre la mortalité maternelle et périnatale. Les trois composantes du SRE, soit les caisses de solidarité, le transport et la communication et la mise à niveau des soins obstétricaux, permettent une action simultanée du côté de la demande et de l’offre de soins maternels et périnatals. Néanmoins, la pénurie de personnel qualifié a conduit à des compromis sur la qualification du personnel dans l’implantation de ce système. La région de Kayes, première région administrative du Mali, est une région de forte émigration. Elle dispose d’une offre de soins plus diversifiée qu’ailleurs au Mali, grâce à l’appui des Maliens de l’extérieur. Son SRE offre ainsi un terrain d’études adéquat pour l’analyse du rôle des professionnels de première ligne. De façon plus spécifique, ce travail avait pour objectifs 1) d’identifier les caractéristiques des équipes de soins de première ligne qui sont associées à une meilleure performance du SRE en termes de survie simultanée de la mère et du nouveau-né et 2) d’approfondir la compréhension des pratiques de gestion des ressources humaines, susceptibles d’expliquer les variations de la performance du SRE de Kayes. Pour atteindre ces objectifs, nous avons, à partir du cadre de référence de Michie et West modélisé les facteurs liés aux ressources humaines qui ont une influence potentielle sur la performance du SRE de Kayes. L’exploration des variations du processus motivationnel a été faite à partir de la théorie de l’attente de Vroom. Nous avons ensuite combiné une revue de la littérature et un devis de recherche mixte (quantitative et qualitative). Les données pour les analyses quantitatives proviennent d’un système d’enregistrement continu de toutes les urgences obstétricales (GESYRE : Gestion du Système de Référence Évacuation mis en place depuis 2004 dans le cadre du suivi et de l’évaluation du SRE de Kayes) et des enquêtes à passages répétés sur les données administratives et du personnel des centres de santé. Un modèle de régression biprobit a permis d’évaluer les effets du niveau d’entrée dans le SRE et des équipes de soins sur la survie jointe de la mère et du nouveau-né. A l’aide d’entrevues semi-structurées et d’observations, nous avons exploré les pratiques de gestion des personnes dans des centres de santé communautaires « CScom » sélectionnés par un échantillonnage raisonné. Les résultats de ce travail ont confirmé que la main d’œuvre humaine demeure cruciale pour la performance du SRE. Les professionnels de première ligne ont influencé la survie des femmes et des nouveau-nés, à morbidités égales, et lorsque la distance parcourue est prise en compte. La meilleure survie de la mère et du nouveau-né est retrouvée dans les cas d’accès direct à l’hôpital régional. Les femmes qui sont évacuées des centres de première ligne où il y a plus de professionnels ou un personnel plus qualifié avaient un meilleur pronostic materno-fœtal que celles qui ont consulté dans des centres qui disposent de personnel peu qualifié. Dans les centres de première ligne dirigés par un médecin, des variations favorables à la performance comme une implication directe des médecins dans les soins, un environnement de soins concurrentiel ont été retrouvés. Concernant les pratiques de gestion dans les centres de première ligne, les chefs de poste ont mis en place des incitatifs pour motiver le personnel à plus de performance. Le processus motivationnel demeure toutefois très complexe et variable. La désirabilité de bons résultats des soins (valence) est élevée pour tous les professionnels ; cependant les motifs étaient différents entre les catégories de personnel. Par ailleurs, le faible niveau d’équipements et la multiplicité des acteurs ont empêché l’établissement d’un lien entre l’effort fourni par les professionnels et les résultats de soins. Cette compréhension du rôle des professionnels de première ligne pourra aider le personnel administratif à mieux cibler le monitorage de la performance du SRE. Le personnel de soins pourra s’en servir pour reconnaitre et appliquer les pratiques associées à une bonne performance. Dans le domaine de la recherche, les défis de recherche ultérieurs sur les facteurs humains de la performance du SRE seront mieux identifiés.

Effectiveness Of Feature Detection Operators On The Performance Of Iris Biometric Recognition System

Iris Recognition is a highly efficient biometric identification system with great possibilities for future in the security systems area.Its robustness and unobtrusiveness, as opposed tomost of the currently deployed systems, make it a good candidate to replace most of thesecurity systems around. By making use of the distinctiveness of iris patterns, iris recognition systems obtain a unique mapping for each person. Identification of this person is possible by applying appropriate matching algorithm.In this paper, Daugman’s Rubber Sheet model is employed for irisnormalization and unwrapping, descriptive statistical analysis of different feature detection operators is performed, features extracted is encoded using Haar wavelets and for classification hammingdistance as a matching algorithm is used. The system was tested on the UBIRIS database. The edge detection algorithm, Canny, is found to be the best one to extract most of the iris texture. The success rate of feature detection using canny is 81%, False Accept Rate is 9% and False Reject Rate is 10%.