Quantification of the relationship between Fuser Roller Temperature and Laser Printer Emissions

Recently published studies not only demonstrated that laser printers are often significant sources of ultrafine particles, but they also shed light on particle formation mechanisms. While the role of fuser roller temperature as a factor affecting particle formation rate has been postulated, its impact has never been quantified. To address this gap in knowledge, this study measured emissions from 30 laser printers in chamber using a standardized printing sequence, as well as monitoring fuser roller temperature. Based on a simplified mass balance equation, the average emission rates of particle number, PM2.5 and O3 were calculated. The results showed that: almost all printers were found to be high particle number emitters (i.e. > 1.01×1010 particles/min); colour printing generated more PM2.5 than monochrome printing; and all printers generated significant amounts of O3. Particle number emissions varied significantly during printing and followed the cycle of fuser roller temperature variation, which points to temperature being the strongest factor controlling emissions. For two sub-groups of printers using the same technology (heating lamps), systematic positive correlations, in the form of a power law, were found between average particle number emission rate and average roller temperature. Other factors, such as fuser material and structure, are also thought to play a role, since no such correlation was found for the remaining two sub-groups of printers using heating lamps, or for the printers using heating strips. In addition, O3 and total PM2.5 were not found to be statistically correlated with fuser temperature.

Formation mechanisms of secondary organic aerosols in relation to laser printer emissions

Due to their large surface area, complex chemical composition and high alveolar deposition rate, ultrafine particles (UFPs) (< 0.1 ìm) pose a significant risk to human health and their toxicological effects have been acknowledged by the World Health Organisation. Since people spend most of their time indoors, there is a growing concern about the UFPs present in some indoor environments. Recent studies have shown that office machines, in particular laser printers, are a significant indoor source of UFPs. The majority of printer-generated UFPs are organic carbon and it is unlikely that these particles are emitted directly from the printer or its supplies (such as paper and toner powder). Thus, it was hypothesised that these UFPs are secondary organic aerosols (SOA). Considering the widespread use of printers and human exposure to these particles, understanding the processes involved in particle formation is of critical importance. However, few studies have investigated the nature (e.g. volatility, hygroscopicity, composition, size distribution and mixing state) and formation mechanisms of these particles. In order to address this gap in scientific knowledge, a comprehensive study including state-of-art instrumental methods was conducted to characterise the real-time emissions from modern commercial laser printers, including particles, volatile organic compounds (VOCs) and ozone (O3). The morphology, elemental composition, volatility and hygroscopicity of generated particles were also examined. The large set of experimental results was analysed and interpreted to provide insight into: (1) Emissions profiles of laser printers: The results showed that UFPs dominated the number concentrations of generated particles, with a quasi unimodal size distribution observed for all tests. These particles were volatile, non-hygroscopic and mixed both externally and internally. Particle microanalysis indicated that semi-volatile organic compounds occupied the dominant fraction of these particles, with only trace quantities of particles containing Ca and Fe. Furthermore, almost all laser printers tested in this study emitted measurable concentrations of VOCs and O3. A positive correlation between submicron particles and O3 concentrations, as well as a contrasting negative correlation between submicron particles and total VOC concentrations were observed during printing for all tests. These results proved that UFPs generated from laser printers are mainly SOAs. (2) Sources and precursors of generated particles: In order to identify the possible particle sources, particle formation potentials of both the printer components (e.g. fuser roller and lubricant oil) and supplies (e.g. paper and toner powder) were investigated using furnace tests. The VOCs emitted during the experiments were sampled and identified to provide information about particle precursors. The results suggested that all of the tested materials had the potential to generate particles upon heating. Nine unsaturated VOCs were identified from the emissions produced by paper and toner, which may contribute to the formation of UFPs through oxidation reactions with ozone. (3) Factors influencing the particle emission: The factors influencing particle emissions were also investigated by comparing two popular laser printers, one showing particle emissions three orders of magnitude higher than the other. The effects of toner coverage, printing history, type of paper and toner, and working temperature of the fuser roller on particle number emissions were examined. The results showed that the temperature of the fuser roller was a key factor driving the emission of particles. Based on the results for 30 different types of laser printers, a systematic positive correlation was observed between temperature and particle number emissions for printers that used the same heating technology and had a similar structure and fuser material. It was also found that temperature fluctuations were associated with intense bursts of particles and therefore, they may have impact on the particle emissions. Furthermore, the results indicated that the type of paper and toner powder contributed to particle emissions, while no apparent relationship was observed between toner coverage and levels of submicron particles. (4) Mechanisms of SOA formation, growth and ageing: The overall hypothesis that UFPs are formed by reactions with the VOCs and O3 emitted from laser printers was examined. The results proved this hypothesis and suggested that O3 may also play a role in particle ageing. In addition, knowledge about the mixing state of generated particles was utilised to explore the detailed processes of particle formation for different printing scenarios, including warm-up, normal printing, and printing without toner. The results indicated that polymerisation may have occurred on the surface of the generated particles to produce thermoplastic polymers, which may account for the expandable characteristics of some particles. Furthermore, toner and other particle residues on the idling belt from previous print jobs were a very clear contributing factor in the formation of laser printer-emitted particles. In summary, this study not only improves scientific understanding of the nature of printer-generated particles, but also provides significant insight into the formation and ageing mechanisms of SOAs in the indoor environment. The outcomes will also be beneficial to governments, industry and individuals.

Ozone-initiated particle formation, particle aging, and precursors in a laser printer

An increasing number of researchers have hypothesized that ozone may be involved in the particle formation processes that occur during printing, however no studies have investigated this further. In the current study, this hypothesis was tested in a chamber study by adding supplemental ozone to the chamber after a print job without measurable ozone emissions. Subsequent particle number concentration and size distribution measurements showed that new particles were formed minutes after the addition of ozone. The results demonstrated that ozone did react with printer-generated volatile organic compounds (VOCs) to form secondary organic aerosols (SOAs). The hypothesis was further confirmed by the observation of correlations among VOCs, ozone, and particles concentrations during a print job with measurable ozone emissions. The potential particle precursors were identified by a number of furnace tests, which suggested that squalene and styrene were the most likely SOA precursors with respect to ozone. Overall, this study significantly improved scientific understanding of the formation mechanisms of printer-generated particles, and highlighted the possible SOA formation potential of unsaturated nonterpene organic compounds by ozone-initiated reactions in the indoor environment. © 2011 American Chemical Society.

Monitoring charged particle and ion emissions from a laser printer

While the emission rate of ultrafine particles has been measured and quantified, there is very little information on the emission rates of ions and charged particles from laser printers. This paper describes a methodology that can be adopted for measuring the surface charge density on printed paper and the ion and charged particle emissions during operation of a high-emitting laser printer and shows how emission rates of ultrafine particles, ions and charged particles may be quantified using a controlled experiment within a closed chamber.

Sustainability in post disaster road infrastructure recovery projects and asset management

Civil infrastructure and especially roads are being impacted with increasing frequency by flood, Tsunami, cyclone related natural and manmade disasters in the world. Responding to such events and in preparing for more regular and intense climate-change induced events in future, the road governing agencies are reviewing how postdisaster road infrastructure recovery projects are best planned and delivered. In particular, there is awareness that rebuilding such infrastructure require sustainable asset management strategies across economic, environmental and social dimensions. A comprehensive asset management framework for pre and post disaster situations can minimize negative impacts on our communities, economy and environment. This research paper is focused on post disaster management in road infrastructures and road infrastructure asset management strategies used by road authorities. Analyzing the implications of disruption to transport network and associated services is an important part of preparing local and regional responses to the impacts of disasters. This research paper will contribute to strategic infrastructure asset planning, management leading to safe, efficient and integrated transport system that supports sustainable economic, social and environmental outcomes. This paper also focuses on proper asset management, governance and engineering principles which should be followed and adopted in post disaster recovery projects to maximize sustainability in environmental, social and economic dimensions.

Design of light gauge steel roofing systems subject to high wind forces

Light gauge steel roofing systems made of thin profiled roof sheeting and battens are used commonly in residential, industrial and commercial buildings. Their critical design load combination is that due to wind uplift forces that occur during high wind events such as tropical cyclones and thunderstorms. However, premature local failures at their screw connections have been a concern for many decades since cyclone Tracy that devastated Darwin in 1974. Extensive research that followed cyclone Tracy on the pull-through and pull-out failures of roof sheeting to batten connections has significantly improved the safety of roof sheeting. However, this has made the batten to rafter/truss connection the weakest, and recent wind damage investigations have shown the failures of these connections and the resulting loss of entire roof structures. Therefore an experimental research program using both small scale and full scale air-box tests is currently under way to investigate the pull-through failures of thin-walled steel battens under high wind uplift forces. Tests have demonstrated that occurrence of pull-through failures in the bottom flanges of steel batttens and the need to develop simple test and design methods as a function of many critical parameters such as steel batten geometry, thickness and grade, screw fastener sizes and other fastening details. This paper presents the details of local failures that occur in light fauge roofing systems, a review of the current design and test methods for steel battens and associated short comings, and the test results obtained to date on pull-through failures of battens from small scale and full scale tests. Finally, it proposes the use of suitable small scale test methods that can be used by both researchers and manufacturers of such screw-fastened light gauge steel batten systems.

The impact of fuser roller temperature on laser printer particle emission

The emission of particles in the ultrafine range (<100 nm) from laser printers has not been reported until recently (Uhde et al., 2006; He et al., 2007; Morawska et al., 2009). The research reported to date has provided a body of information about printer emissions and shed light on particle formation mechanisms. However, until now, the effect of fuser roller temperature on particle emissions had not been comprehensively investigated...

Kirjan tie lukijalle : Kirjakauppojen vakiintuminen Suomessa 1740 - 1860

Books Paths to Readers describes the history of the origins and consolidation of modern and open book stores in Finland 1740 1860. The thesis approaches the book trade as a part of a print culture. Instead of literary studies choice to concentrate on texts and writers, book history seeks to describe the print culture of a society and how the literary activities and societies interconnect. For book historians, printed works are creations of various individuals and groups: writers, printers, editors, book sellers, censors, critics and finally, readers. They all take part in the creation, delivery and interpretation of printed works. The study reveals the ways selling and distributing books have influenced the printed works and the literary and print culture. The research period 1740 1860 covers the so-called second revolution of the book, or the modernisation of the print culture. The thesis describes the history of 60 book stores and their 96 owners. The study concentrates on three themes: firstly, how the particular book trade network became a central institution for printed works distribution, secondly what were the relations between cosmopolitan European book markets and the national cultural sphere, and thirdly how book stores functioned as cultural institutions and business enterprises. Book stores that have a varied assortment and are targeted to all readers became the main institution for book trade in Finland during 1740 1860. It happened because of three features. First, the book binders monopoly on selling bound copies in Sweden was abolished in 1740s. As a consequence entrepreneurs could concentrate solely to trade activities and offer copies from various publishers at their stores. Secondly the common business model of bartering was replaced by selling copies for cash, first in the German book trade centre Leipzig in 1770s. The change intensified book markets activities and Finnish book stores foreign connections. Thirdly, after Finland was annexed to the Russian empire in 1809, the Grand duchy s administration steered foreign book trade to book stores (because of censorship demands). Up to 1830 s book stores were available only in Helsinki and Turku. During next ten years book stores opened in six regional centres. The early entrepreneurs ran usually vertical businesses consisting of printing, publishing and distribution activities. This strategy lowered costs, eased the delivery of printed works and helped to create elaborated centres for all book activities. These book stores main clientele consisted of the Swedish speaking gentry. During late 1840s various opinion leaders called for the development of a national Finnish print culture, and also book stores. As a result, during the five years before the beginning of the Crimean war (1853 1856) book stores were opened in almost all Finnish towns: at the beginning of the war 36 book stores operated in 21 towns. The later book sellers, mainly functioning in small towns among Finnish speaking people, settled usually strictly for selling activities. Book stores received most of their revenues from selling foreign titles. Swedish, German, French and Belgian (pirate editions of popular French novels) books were widely available for the multilingual gentry. Foreign titles and copies brought in most of the revenues. Censorship inspections or unfavourable custom fees would not limit the imports. Even if the local Finnish print production steadily rose, many copies, even titles, were never delivered via book stores. Only during the 1840 s and 1850 s the most advanced publishers would concentrate on creating publishing programmes and delivering their titles via book stores. Book sellers regulated commissions were small. They got even smaller because of large amounts of unsold copies, various and usual misunderstandings of consignments and accounts or plain accidents that destroyed shipments and warehouses. Also, the cultural aim of a creating large and assortments and the tendency of short selling periods demanded professional entrepreneurship, which many small town book sellers however lacked. In the midst of troublesome business efforts, co-operation and mutual concern of the book market s entrepreneurs were the key elements of the trade, although on local level book sellers would compete, sometimes even ferociously. The difficult circumstances (new censorship decree of 1850, Crimean war) and lack of entrepreneurship, experience and customers meant that half of the book stores opened in 1845 1860 was shut in less than five years. In 1858 the few leading publishers established The Finnish Book Publishers Association. Its first task was to create new business rules and manners for the book trade. The association s activities began to professionalise the whole network, but at the same time the earlier independence of regional publishing and selling enterprises diminished greatly. The consolidation of modern and open book store network in Finland is a history of a slow and complex development without clear signs of a beginning or an end. The ideal book store model was rarely accomplished in its all features. Nevertheless, book stores became the norm of the book trade. They managed to offer larger selections, reached larger clienteles and maintained constant activity better than any other book distribution model. In essential, the book stores methods have not changed up to present times.

The right path : The autobiography of a survivor /

Account of the German occupation of Kecskemet; fate of Jews of Kecskemet; liberation; immediate postwar experiences in Kecskemet; memories of childhood in Kotaj and Kecskemet; move to Budapest; training as soccer player in Budapest; return to Kecskemet and work in printing shop; fate of family members during the holocaust; early years of World War II in Kecskemet; entry into forced labor; life in labor camp; escape and hiding; liberation by Red Army; return to Kecskemet under Soviet Ukrainian occupation; return to printing business in Kecskemet; courtship and marriage in April 1945; reuinion with two sisters; birth of daugher; move to Budapest in 1949; work as printer in Budapest; life in Budapest under Communist domination; anti-Semitism; uprising of 1956 in Budapest; flight to Vienna; life in Vienna; emigration to USA; life in New York; move to Los Angeles; started business in food preparation; coached soccer team.

Pictures that ask the right questions

An article about the use of photographs as research in the writing of memoir. "I expect many people begin the writing of a memoir by looking through old photos. Pictures, after all, belong in the past, and they hold out the promise of delivering it to us again: everyone is younger, surrounded by yesterday’s world, a moment fixed in time. Even the size of the photo paper and printing tone belong back there, in a printer’s shop that doesn’t exist anymore. And yet, for the purpose of writing a memoir, the most useful pictures also reach beyond the past, and beyond their initial role in verifying your memories, or filling out the details. That is, they are more than an account. Such pictures seem to be asking questions about what happened next, in the moments and years after they were taken..."

Publishing for the Masses : Early Modern English Witchcraft Pamphlets

This study is a pragmatic description of the evolution of the genre of English witchcraft pamphlets from the mid-sixteenth century to the end of the seventeenth century. Witchcraft pamphlets were produced for a new kind of readership semi-literate, uneducated masses and the central hypothesis of this study is that publishing for the masses entailed rethinking the ways of writing and printing texts. Analysis of the use of typographical variation and illustrations indicates how printers and publishers catered to the tastes and expectations of this new audience. Analysis of the language of witchcraft pamphlets shows how pamphlet writers took into account the new readership by transforming formal written source materials trial proceedings into more immediate ways of writing. The material for this study comes from the Corpus of Early Modern English Witchcraft Pamphlets, which has been compiled by the author. The multidisciplinary analysis incorporates both visual and linguistic aspects of the texts, with methodologies and theoretical insights adopted eclectically from historical pragmatics, genre studies, book history, corpus linguistics, systemic functional linguistics and cognitive psychology. The findings are anchored in the socio-historical context of early modern publishing, reading, literacy and witchcraft beliefs. The study shows not only how consideration of a new audience by both authors and printers influenced the development of a genre, but also the value of combining visual and linguistic features in pragmatic analyses of texts.

Polilaktida oinarri duten 3D zelula-euskarri (scaffold) polimeriko biodegradagarrien diseinu, fabrikazio eta propietateak

[EU]Hiru dimentsioko inprimaketa etorkizun handiko teknologia bezala azaltzen zaigu gaur egun. Esate baterako, biomedikuntza arloan aukera berritzaileak ekar ditzake, baina baita hezkuntza, heziketa eta ikerketa munduetan ere. Teknologia berri honen abantailarik nagusiena prototipatze azkarrean datza, eta honi esker, mikro- eta makro- egitura definituak dituzten objektuak diseinatu eta fabrikatu daitezke modu lehiakorrean. Lan honen helburua 3D inprimagailu baten bitartez inprimaturiko polimero biobateragarri eta biodegradagarrietan oinarrituriko ereduen garapen eta fabrikazioan datza. Hala ere, lehenik eta behin, lehengaiak bai fisikoki eta bai termikoki karakterizatu behar dira, ondoren, 3D inprimagailuaren parametroen arteko erlazioa ezarri, eta azkenik, produktu finalaren egitura propietateak eta kalitatea aztertu. Aipaturiko lana aurrera eramateko erabili den materiala polilaktida (PLA) izan da, zeinen erabilera oso zabaldua dagoen medikuntza arloan inplante (torloju, iltze, plaka eta abar) moduan eta ehun ingeniaritzaren munduan.

A Chosen Witness: A Sermon Preached in St. Stephen's Church in Memory of the Rev. Webster

Memorial Sermon preached in memory of the Rev. Walter Gardner Webster