O efeito da desativação térmica nas propriedades oxirredutoras e na atividade catalítica de catalisadores CZ e Pd-CZ

Automotive catalyst, using in Brazil since 1992, is a essential technology for vehicular emissions control. Noble metals are the active phase of these catalysts, and cerium zirconium mixed oxides (CZ), responsibles for the oxygen storage capacity (OSC), one of the most important aspect for the operational performance of the catalyst. In this context, the oxireduction properties analysis of CZ and Pd/CZ (palladium supported in CZ) system are the objective of this study, as well as, the impact of the thermal aging in the OSC. Aging consisted of treatments at 900 or 1200 °C, for 12 or 36 h, in oxidizing condition.

Energetic efficiency of an agricultural tractor in function of tire inflation pressure

The tire inflation pressure, among other factors, determines the efficiency in which a tractor can exert traction. It was studied the effect of using two tire inflation pressures, 110.4 kPa in the front and rear wheels, 124.2 kPa in the front wheel and 138 kPa in the rear wheels, the energetic efficiency of an agricultural tractor of 147 kW of engine power, in the displacement speed of 6.0 km.h-1, on track with firm surface, with the tractor engine speed of 2000 rpm. For each condition of the tire pressure, the tested tractor was subjected to constant forces in the drawbar of 45 kN and 50 kN, covering 30 meters. It was used a randomized complete block with a 2x2 factorial arrangement (tire pressure and drawbar power) with four replications, totaling 16 experimental units. Data were subjected to analysis of variance, using the Tukey test at 5% probability for comparison averages. The lowest hourly and specific fuel consumption, the lowest slippage of the wheelsets and the highest efficiency in the drawbar was obtained with the tire inflation pressure of 110.4 kPa in the front and rear tires of the tractor, highlighting that lower pressures improve energetic and operational performance of the tractor.

Economic analysis for sizing of sugarcane (Saccharum spp.) mechanized harvesting

Sugarcane has a significant role on Brazilian agribusiness economy. The harvesting cane is considered as one of the most important operations of the process for it has to attend the raw material demanded by the sugar mill in quality and a competitive cost. The objective of this work it is it of analyzing, of systemic way, the variables influence on economical and operational performance in sugarcane mechanized harvesting process for sizing of machines. For this purpose a model called "ColheCana", was developed in a spreadsheet and in a programming language. The results showed that the field efficiency and harvester´s initial value are variables of great impact in the cost and that there is a maximum area that one equipment can attend and for this area the cost is minimum.

Quality of peanut mechanical sowing in function of seeding density and size of the seeds

ABSTRACTPeanut crop (Arachis hypogaeaL.) mechanization has been improved over the years; however there are drawbacks that affect the quality of operations. Thus, this article’s objectives were to evaluate the operational performance of the mechanized sowing of peanut crop according to seeding densities (10, 14, and 18 seeds m-1) and seed sizes (21 and 23 mm). It was observed that the seeds of 23 mm had shorter average number of days to emergence and a higher percentage of emergences, occurring the opposite to the seeding density of 18 seeds m-1. The higher the seeding density, the largest was the plant stand, whereas the 23 mm seed obtained the best results and the same with the seeding density of 14 seeds m-1 that had a higher percentage of normal spacing. The densities of 14 and 18 seeds m-1 reflected in higher yields, being always superior to the 23 mm seeds.

Prosessiautomaatio pinnankorkeusmittauksen koelaitteistoissa

Pinnankorkeuden tunteminen kiehutusvesireaktorin painesäiliössä on erittäin tärkeää sen turvallisuusvaikutusten takia. Pinnankorkeutta mitataan vesipatsaiden korkeutta havaitsevien paine-eromittausten avulla. Säteilyturvakeskuksen YVL-ohjeiden mukaan turvallisuuteen vaikuttavien mittausten täytyy noudattaa moninkertaistus- ja erilaisuusperiaatteita. Yleensä erilaisuusperiaatetta on toteutettu käyttämällä erityyppisiä paine-eromittareita, mutta erilaisella fysikaalisella toimintaperiaatteella oleva mittaus olisi parempi ja toteuttaisi paremmin erilaisuusperiaatetta. Uimurikytkin olisi tällainen fysikaalisesti eri periaatteeseen perustuva pinnankorkeuden mittauslaite. Ydinvoimalaan tarkoitettu teknologia tulee kelpoistaa riippumattoman tahon toimesta ennen käyttöönottoa. Kelpoistamiskokeita varten Lappeenrannan teknillisen yliopiston Ydinturvallisuuden tutkimusyksikköön rakennettiin vuosina 2011–2013 kaksi koelaitteistoa. Näillä koelaitteistoilla tutkittiin uimurikytkimien toimintaa ja ominaisuuksia erilaisissa kiehutusvesireaktorin käyttötilanteissa. Koelaitteistot tarvitsivat toimiakseen automaatiojärjestelmät, jotka suunniteltiin pääosin noudattamalla suunnittelun elinkaarimallia sekä automaatiosuunnittelun sisältökokonaisuuksia. Automaatiojärjestelmien suunnittelu aloitettiin määrittelemällä koejärjestelyjen asettamat vaatimukset, jonka jälkeen tehtiin teknologiavalinnat. Seuraavaksi suunniteltiin automaatiojärjestelmien logiikkaohjelmistot, joiden kuvaukseen tämä työ pääasiassa keskittyy. Logiikkaohjelmistot toteutettiin graafisella National Instruments LabView -ohjelmointikielellä. Logiikkaohjelmistojen tuli hoitaa tiedonkeruuta, käyttöautomaatiota, turvallisuustehtäviä sekä kokeisiin liittyviä erikoistehtäviä. Ohjelmistot saatiin esikokeiden aikana toimimaan halutusti, ja varsinaiset kokeet voitiin suorittaa ilman merkittäviä ongelmia.

Tulosohjauksen kehittämiskohteet Rikosseuraamuslaitoksella

Diplomityön tavoitteena on Rikosseuraamuslaitoksen tulosohjauksen kuvaaminen, mää-rittely, arviointi ja kehitysehdotusten tekeminen. Lisäksi määritellään normi- ja informaa-tio-ohjaus sekä tarkastellaan kuinka ne näkyvät tulosohjauksessa. Informaatio-ohjauksesta tuodaan esille keskeisimpiä kehityskohteita. Toiminnan tehostamistarpeet johtuvat yleisestä taloustilanteesta ja sitä seuraavasta määrärahojen pienenemisestä. Aluksi pidettiin puolistrukturoidut haastattelut, joiden perusteella kuvattiin laitoksen pro-sessikartta. Tämän jälkeen tulos- ja normiohjauksesta tehtiin eritasoisia prosessikuvauk-sia. Kuvauksilla rajattiin ja selvennettiin tarkasteltavia prosesseja. Kirjallisuuden, tutki-musten ja selvitysten avulla kartoitettiin tulosohjauksen yleisiä kehityskohteita. Niitä ver-rattiin haastattelutietoihin, arvioitiin tulosohjauksen nykytilaa ja tehtiin kehitysehdotuksia. Tulosohjauksesta löytyi useita kehityskohteita. Strategisen toimenpidesuunnitelman edis-tymiseen tulisi tehdä raportointiaikataulu. Tulostavoitteita voisi valmistella enemmän työntekijälähtöisesti ja yksiköille tulisi laatia omat strategiat. Asiakaspalautekyselyä tulisi kehittää, toteuttaa se verkkopohjaisena ja ottaa käyttöön kaikissa yksiköissä. Mittarit tuli-si liittää ydinprosesseihin ja jakaa ne laitos-alue-yksikkö -tasoille. Säännölliset raportit tulisi automatisoida ja antaa niiden tulostusoikeudet käyttäjille. Lisäksi kehittämishankkeita ja projekteja voisi hieman vähentää mutta viedä ne tehokkaammin läpi. Normi- ja informaatio-ohjaus ovat kiinteä osa tulosohjausta. Normiohjaus perustuu pääasiassa säädöksiin ja informaatio-ohjaus tiedolla ohjaamiseen. Informaatio-ohjauksessa tulisi kiinnittää huomiota aluekeskuksen tiedottamiseen, ettei yksiköitä ohjata keskushallinnosta aluekeskuksen ohi. Keskushallinnon tulisi myös päivittää ohjeistukset nopeammin erityisesti lakimuutosten yhteydessä. Myös vastuuta voisi jakaa enemmän alueille. Käyttöön voisi ottaa uuden tiedotuskanavan, esimerkiksi sähköinen uutislehtinen tai info-näytöt taukotiloissa.

Investigations on Longline Fishing in Lakshadweep Sea with special reference to Bycatch Issues Bait and Hook Selectivity

The main objectives of the present study have been studies on the operational performance of tuna longline in Lakshadweep Sea studies on the efficiency of hooks in the longline operation studies on the efficiency of baits in the longline operation studies on bycatch in longline operation studies on predation on the longline catch and the hook loss encountered during the fishing operation

Modelling and simulation of a photovoltaic fuel cell hybrid system

A stand-alone power system is an autonomous system that supplies electricity to the user load without being connected to the electric grid. This kind of decentralized system is frequently located in remote and inaccessible areas. It is essential for about one third of the world population which are living in developed or isolated regions and have no access to an electricity utility grid. The most people live in remote and rural areas, with low population density, lacking even the basic infrastructure. The utility grid extension to these locations is not a cost effective option and sometimes technically not feasible. The purpose of this thesis is the modelling and simulation of a stand-alone hybrid power system, referred to as “hydrogen Photovoltaic-Fuel Cell (PVFC) hybrid system”. It couples a photovoltaic generator (PV), an alkaline water electrolyser, a storage gas tank, a proton exchange membrane fuel cell (PEMFC), and power conditioning units (PCU) to give different system topologies. The system is intended to be an environmentally friendly solution since it tries maximising the use of a renewable energy source. Electricity is produced by a PV generator to meet the requirements of a user load. Whenever there is enough solar radiation, the user load can be powered totally by the PV electricity. During periods of low solar radiation, auxiliary electricity is required. An alkaline high pressure water electrolyser is powered by the excess energy from the PV generator to produce hydrogen and oxygen at a pressure of maximum 30bar. Gases are stored without compression for short- (hourly or daily) and long- (seasonal) term. A proton exchange membrane (PEM) fuel cell is used to keep the system’s reliability at the same level as for the conventional system while decreasing the environmental impact of the whole system. The PEM fuel cell consumes gases which are produced by an electrolyser to meet the user load demand when the PV generator energy is deficient, so that it works as an auxiliary generator. Power conditioning units are appropriate for the conversion and dispatch the energy between the components of the system. No batteries are used in this system since they represent the weakest when used in PV systems due to their need for sophisticated control and their short lifetime. The model library, ISET Alternative Power Library (ISET-APL), is designed by the Institute of Solar Energy supply Technology (ISET) and used for the simulation of the hybrid system. The physical, analytical and/or empirical equations of each component are programmed and implemented separately in this library for the simulation software program Simplorer by C++ language. The model parameters are derived from manufacturer’s performance data sheets or measurements obtained from literature. The identification and validation of the major hydrogen PVFC hybrid system component models are evaluated according to the measured data of the components, from the manufacturer’s data sheet or from actual system operation. Then, the overall system is simulated, at intervals of one hour each, by using solar radiation as the primary energy input and hydrogen as energy storage for one year operation. A comparison between different topologies, such as DC or AC coupled systems, is carried out on the basis of energy point of view at two locations with different geographical latitudes, in Kassel/Germany (Europe) and in Cairo/Egypt (North Africa). The main conclusion in this work is that the simulation method of the system study under different conditions could successfully be used to give good visualization and comparison between those topologies for the overall performance of the system. The operational performance of the system is not only depending on component efficiency but also on system design and consumption behaviour. The worst case of this system is the low efficiency of the storage subsystem made of the electrolyser, the gas storage tank, and the fuel cell as it is around 25-34% at Cairo and 29-37% at Kassel. Therefore, the research for this system should be concentrated in the subsystem components development especially the fuel cell.

La construcción de sentido del inicio de un cambio estratégico en las organizaciones: el caso de la Universidad del Rosario

A través de un caso de estudio se explora cómo la construcción de sentido de un grupo de directivos, bajo una misma inspiración, generó el inicio de un cambio estratégico en una prestigiosa y reconocida universidad colombiana, la Universidad del Rosario. Una institución que en un momento determinado notó que estaba siendo percibida dentro del sector de la educación superior como pequeña, estática en el avance de algunas disciplinas del conocimiento y conservadora; en otras palabras, que estaba perdiendo el reconocimiento que usualmente la había acompañado. A través del estudio de este caso se utilizó la técnica de análisis de discurso para comprender la construcción de sentido del inicio de un cambio estratégico en las organizaciones. Esta técnica permitió analizar la información cualitativa derivada de las entrevistas que se realizaron en profundidad a la cúpula de directivos de la institución y a algunos destacados representantes del sector de la Educación Superior en Colombia. Los resultados sugieren que se hicieron presentes, efectivamente, algunas condiciones específicas que marcaron el inicio de un cambio estratégico en la institución y un viraje en su identidad e imagen. Hechos que se sustentaron en los miembros de un equipo que procuró interpretar y comprender los cambios existentes en el entorno global y local, y asimilar, igualmente, algunos destacados retos que se planteaban por aquella época, al interior de la propia Universidad

Las TIC en la administración de la cadena de suministro y su incidencia en el desempeño operacional

Las tecnologías de la información han empezado a ser un factor importante a tener en cuenta en cada uno de los procesos que se llevan a cabo en la cadena de suministro. Su implementación y correcto uso otorgan a las empresas ventajas que favorecen el desempeño operacional a lo largo de la cadena. El desarrollo y aplicación de software han contribuido a la integración de los diferentes miembros de la cadena, de tal forma que desde los proveedores hasta el cliente final, perciben beneficios en las variables de desempeño operacional y nivel de satisfacción respectivamente. Por otra parte es importante considerar que su implementación no siempre presenta resultados positivos, por el contrario dicho proceso de implementación puede verse afectado seriamente por barreras que impiden maximizar los beneficios que otorgan las TIC.

Simple and effective technical procedures for the packing and application of nanospray PicoFrit HPLC columns for proteomic analyses

A simple procedure was developed for packing PicoFrit HPLC columns with chromatographic stationary phase using a reservoir fabricated from standard laboratory HPLC fittings. Packed columns were mounted onto a stainless steel ultra-low volume precolumn filter assembly containing a 0.5-mu m pore size steel frit. This format provided a conduit for the application of the nanospray voltage and protected the column from obstruction by sample material. The system was characterised and operational performance assessed by analysis of a range of peptide standards (n = 9).

A logística militar e o serviço de intendência: uma análise do programa excelência gerencial do Exército Brasileiro

This study has the purpose to analyze some of the programs and measures adopted by the Brazilian Army, as well as eventual contributions, for the modernization of its Logistics. Thus, focus one of the main devices of logistic support of the Forces, the Quartermaster, approaching some roles performed by this Service that comprises the current conception of the Army Logistics. This modernization process is mainly developed through a excellence program implemented for the whole Army aiming, amongst other factors, the adoption of managerial practices leading to a better operational performance and to the improvement of the Institution' services and products quality: the Managerial Excellence Program of the Brazilian Army (PEG-EB). Here, the Logistics is deemed as key part for the organizational success and one of the main factors of competitive differential of companies, directly related to costs reduction and increase in the level of services provided for the customers. For the Army, the improvement and update of logistic doctrine emerge as priority for achieving the goals, especially focusing the need to integrated the logistics activities, in order to optimize the resources available, reduce costs and prioritize its actions. While searching for an integrated approach for its logistics, the Army created a central body with the responsibility to coordinate all the supply chain of its Units: the Logistic Department (D Log). This body centrally coordinates a major segment of logistics functions in the Forces. The conclusion states that the development of this mentality about the internal integration of activities will allow a rationalization of the management process, increasing the indexes of availability of material from military organizations, and consequently a serviceability gain for the Brazilian Army.

A gestão da logística em empresas de rochas ornamentais: um estudo de caso comparativo

This dissertation attempts to reach four goals: 1) to characterize the logistics development stage in two firms from the stone industry, an export firm and a non-export firm; 2) to identify the logistics functions performed by the firms themselves and the activities that are outsourced and also the reasons; 3) to describe the supply chain of the stone industry; 4) to apply a model called Leading Edge Logistics (BOWERSOX et al. 1992) to evaluate the current gaps between these firms in terms of organizational structure, information technology and performance system. This study has demonstrated that the export firm presented more adherence to the model compared to the non-export one, showing better entrepreneurial and operational performance. Furthermore, it has also confirmed the expectations generated by the conceptual model, as follow: the export firm, due to the more complex operational environment, represented by its involvement in a more competitive and demanding sector, i.e. the foreign trade market, has developed a greater level of sophistication of the logistical organization than the non-export one, achieving a better level of flexibility and therefore becoming more competitive.

Análise dos impactos do novo modelo de competitividade do sistema financeiro nacional no desempenho dos empregados dos Bancos Públicos de Varejo: o caso do BRC S/A

o estudo tem como principal foco apresentar uma referência de análise do comportamento individual dos empregados dos bancos de varejo diante da necessidade de adequação à estratégia utilizada para enfrentar o atual mercado competitivo. Mostra a importância da análise da dimensão simbólica para as organizações, os negócios e as relações entre os atores no contexto empresarial. Demonstra as principais mudanças recentes no Sistema Financeiro Nacional, que tem levado as organizações aí inseridas a buscar formas de adaptações, entre elas rever seus processos de gestão e de programas de treinamento e desenvolvimento de pessoas. Traça o perfil atual do Banco BRC SIA, fazendo um breve histórico e abordando os recursos humanos, a informatização, o projeto de saneamento fmanceiro e o desempenho operacional dos últimos anos. Conclui que as características culturais do Banco BRC SI A, em sua maIOrIa, reduzem a sua capacidade de adequar-se à forma de atuação dos bancos privados. Existem poucos traços culturais que favorecem a adaptabilidade do banco, entre os quais podemos citar o compromisso, a dedicação e a lealdade do pessoal ao banco (que já foram maiores no passado). Outros fatores também contribuem para dificultar a sua adaptabilidade, tais como o paternalismo, o formalismo, a impunidade, a postura de expectador, entre outras, características estas comuns às empresas brasileiras, conforme veremos no primeiro capítulo. Com relação a isto, será necessária uma forte dose de persistência e desejo de quebrar a inércia da organização, bem como uma constância de propósitos, para que as transformações aconteçam e o banco consiga se adaptar ao mercado. No caso, este deve ser o papel da liderança: ser persistente, perspicaz e flexível o suficiente para chamar o processo a si e conduzi-lo de forma eficaz. Ainda, contatou-se que existem resistências e dificuldades para a viabilização das transformações necessárias para que o banco atue como um banco privado. Algumas resistências são comuns e outras são específicas e próprias de cada situação observada.

Uma investigação empírico-exploratória acerca da causalidade dos indicadores operacionais de call center com a satisfação dos clientes

Year after year the call center industry comes presenting high growth, either in Brazil or the world, using increasing contingent of people and receiving large amount of financial resources. Supporting all this industry, exists a theoretical reference that privileges the search of the improvement of diverse operational performance indicators. This study, empirically examines the relationship between caller satisfaction and diverse operational performance indicators currently used for call center management in Brazil. For in such a way, a group of telecommunications segment call centers will be used searching to determine which indicators are really more significantly correlated with the customer satisfaction. Of this form, it is aimed at to add new evidences and explanations to existing literature, in way that companies of call center industry can give a more adequate service to their customer, opposite to solely focus its efforts in the improvement of a great set of performance pointers that, effectively, can not become related with the customer satisfaction.