Cu2ZnSnS4 absorber layers obtained through sulphurization of metallic precursors: Graphite box versus sulphur flux

In this work we employed a hybrid method, combining RF-magnetron sputtering with evaporation, for the deposition of tailor made metallic precursors, with varying number of Zn/Sn/Cu (ZTC) periods and compared two approaches to sulphurization. Two series of samples with 1×, 2× and 4× ZTC periods have been prepared. One series of precursors was sulphurized in a tubular furnace directly exposed to a sulphur vapour and N2+5% H2 flux at a pressure of 5.0×10+4 Pa. A second series of identical precursors was sulphurized in the same furnace but inside a graphite box where sulphur pellets have been evaporated again in the presence of N2+5% H2 and at the same pressure as for the sulphur flux experiments. The morphological and chemical analyses revealed a small grain structure but good average composition for all three films sulphurized in the graphite box. As for the three films sulphurized in sulphur flux grain growth was seen with the increase of the number of ZTC periods whilst, in terms of composition, they were slightly Zn poor. The films' crystal structure showed that Cu2ZnSnS4 is the dominant phase. However, in the case of the sulphur flux films SnS2 was also detected. Photoluminescence spectroscopy studies showed an asymmetric broad band emission whichoccurs in the range of 1–1.5 eV. Clearly the radiative recombination efficiency is higher in the series of samples sulphurized in sulphur flux. We have found that sulphurization in sulphur flux leads to better film morphology than when the process is carried out in a graphite box in similar thermodynamic conditions. Solar cells have been prepared and characterized showing a correlation between improved film morphology and cell performance. The best cells achieved an efficiency of 2.4%.

The black box of health care expenditure growth determinants

In this paper, the determinants of growth of aggregate health expenditures are investigated. The study departs from previous literature in that it looks at differences across countries in growth (and not levels) of health care expenditures. Estimation is made for 24 OECD countries. Health system characteristics usually believed to influence health expenditures growth, like population ageing, the type of health system (public reimbursement, public contract or integrate) and existence of gatekeepers, are found to be non-significant. Nevertheless, there is evidence that health expenditures experienced a clear slower growth in the last decade. The explanation for this slowdown could not be found in the proposed model and should stimulate further research.

PME.Box: Internationalization to Poland

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Management from the NOVA – School of Business and Economics

EDP InovCity pilot study proposal: A set-top box interface

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Management from the NOVA – School of Business and Economics

Business plan PME.Box: internationalization to Spain

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Management from the NOVA – School of Business and Economics

How to increase value for customers of style in a box: The first Portuguese online platform for renting luxury dresses

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Management from the NOVA – School of Business and Economics

EDP inovcity pilot study proposal: A set-top box interface

In this work I propose an additional test to be implemented in EDP’s residential electricity use feedback trials, under InovCity’s project scope. The proposed product to be tested consists of an interface between the smart meter and the television, through a set-top box. I provide a theoretical framework of the importance of feedback, an analysis of results from past studies involving smart metering, and a detailed description of my proposal. The results of a self-developed questionnaire related to the proposal and segmentation issues are also analyzed. Finally, general conclusions are drawn and potential future improvements and challenges are presented.

Optimisation and design of post-tensioning anchorage corner blisters in concrete box girder bidges

The design of anchorage blisters of internal continuity post-tensioning tendons of bridges built by the cantilever method, presents some peculiarities, not only because they are intermediate anchorages but also because these anchorages are located in blisters, so the prestressing force has to be transferred from the blister the bottom slab and web of the girder. The high density of steel reinforcement in anchorage blisters is the most common reason for problems with concrete cast in situ, resulting in zones with low concrete compacity, leading to concrete crushing failures under the anchor plates. A solution may involve improving the concrete compression and tensile strength. To meet these requirements a high-performance fibre reinforced self-compacting mix- ture (HPFRC) was used in anchorage corner blisters of post-tensioning tendons, reducing the concrete cross-section and decreasing the reinforcement needed. To assess the ultimate capacity and the adequate serviceability of the local anchorage zone after reducing the minimum concrete cross-section and the confining reinforcement, specified by the anchorage device supplier for the particular tendon, load transfer tests were performed. To investigate the behaviour of anchorage blisters regarding the transmission of stresses to the web and the bottom slab of the girder, and the feasibility of using high performance concrete only in the blister, two half scale models of the inferior corner of a box girder existing bridge were studied: a reference specimen of ordinary reinforced concrete and a HPFRC blister specimen. The design of the reinforcement was based in the tensile forces obtained on strut-and-tie models. An experimental program was carried out to assess the models used in design and to study the feasibility of using high performance concrete only in the blister, either with casting in situ, or with precast solutions. A non-linear finite element analysis of the tested specimens was also performed and the results compared.

Numerical Assessment of the out-of-plane response of a brick masonry structure without box behaviour

This paper presents the assessment of the out-of-plane response due to seismic loading of a masonry structure without rigid diaphragm. This structure corresponds to real scale brick masonry specimen with a main façade connected to two return walls. Two modelling approaches were defined for this evaluation. The first one consisted on macro modelling, whereas the second one on simplified micro modelling. As a first step of this study, static nonlinear analyses were conducted to the macro model aiming at evaluating the out-of-plane response and failure mechanism of the masonry structure. A sensibility analyses was performed in order to assess the mesh size and material model dependency. In addition, the macro models were subjected to dynamic nonlinear analyses with time integration in order to assess the collapse mechanism. Finally, these analyses were also applied to a simplified micro model of the masonry structure. Furthermore, these results were compared to experimental response from shaking table tests. It was observed that these numerical techniques simulate correctly the in-plane behaviour of masonry structures. However, the

Convection and segregation of beads in a flat rotating box

Magdeburg, Univ., Fak. für Naturwiss., Diss., 2012

Aplicació de l'ACV a l'envasat del vi : "Bag in Box" front a l'envàs de vidre tradicional

L’objectiu d’aquest projecte és la comparació, des del punt de vista ambiental, de l’envasat del vi mitjançant ampolles de vidre i mitjançant el sistema “Bag-in-Box” reutilitzable.

Mafia in the ballot box

We study the impact of organized crime on electoral competition. Assuming that the mafia is able to bring votes to the supported party in exchange of money, we show that (i) the strongest party is willing to pay the highest price to secure mafia services; (ii) the volume of electoral trade with the mafia increases with political competition and with the efficiency of the mafia. Studying in detail parliamentary elections in Sicily for the period 1946- 1992, we document the significant support given by the Sicilian Mafia to the Christian Democratic party, starting at least from the 1970s. This is consistent with our theoretical predictions, as political competition became much tighter during the 1970s and the Sicilian mafia experienced an extensive centralization process towards the end of the 1960s, which increased substantially its control of the territory. We also provide evidence that in exchange for its electoral support the mafia got economic advantages for its activities in the construction industry.

The Black Box of Business Dynamics

Research in business dynamics has been advancing rapidly in the last years but the translation of the new knowledge to industrial policy design is slow. One striking aspect in the policy area is that although research and analysis do not identify the existence of an specific optimal rate of business creation and business exit, governments everywhere have adopted business start-up support programs with the implicit principle that the more the better. The purpose of this article is to contribute to understand the implications of the available research for policy design. Economic analysis has identified firm heterogeneity as being the most salient characteristic of industrial dynamics, and so a better knowledge of the different types of entrepreneur, their behavior and their specific contribution to innovation and growth would enable us to see into the ‘black box’ of business dynamics and improve the design of appropriate public policies. The empirical analysis performed here shows that not all new business have the same impact on relevant economic variables, and that self-employment is of quite a different economic nature to that of firms with employees. It is argued that public programs should not promote indiscriminate entry but rather give priority to able entrants with survival capacities. Survival of entrants is positively related to their size at birth. Innovation and investment improve the likelihood of survival of new manufacturing start-ups. Investment in R&D increases the risk of failure in new firms, although it improves the competitiveness of incumbents.

Fiscal Federalism at the Ballot Box : The Relevance of Expressive Voting

This paper explores the impact of citizens' motivation to vote on the pattern of fiscal federalism. If the only concern of instrumental citizens was outcome they would have little incentive to vote because the probability that a single vote might change an electoral outcome is usually minuscule. If voters turn out in large numbers to derive intrinsic value from action, how will these voters choose when considering the role local jurisdictions should play? The first section of the paper assesses the weight that expressive voters attach to an instrumental evaluation of alternative outcomes. Predictions are tested with reference to case study analysis of the way Swiss voters assessed the role their local jurisdiction should play. The relevance of this analysis is also assessed with reference to the choice that voters express when considering other local issues. Textbook analysis of fiscal federalism is premised on the assumption that voters register choice just as 'consumers' reveal demand for services in a market, but how robust is this analogy.