Crystallization and characterization of substoichiometric compound (W0.5Al0.5)C-0..5 obtained by solid-state reaction

(W0.5Al0.5)C-0.5 substoichiometric compound is synthesized by a combination of mechanical milling and high-pressure reactive sintering. X-ray diffraction is used to monitor the phase changes and crystallization of (W0.5Al0.5) C-0.5 during the whole reaction process. As a result, (W0.5Al0.5) C-0.5 is identified as the hexagonal WC-type belonging to the P-6m2 space group (No. 187), and the lattice parameters of (W0.5Al0.5)C-0.5 are calculated to be a = 2.907 (1) angstrom, c = 2.838 (1) angstrom, which are very similar to those of WC even if there are approximately 50 pct carbon vacancies in the cell of (W0.5Al0.5)C-0.5 as compared with WC. The substoichiometric (W0.5Al0.5)C-0.5 compound has a Vickers microhardness of 2385 +/- 70 kg mm(-2), which is as high as that of WC, while its density is far lower than that of WC.

Luminescence properties of RP1-xVxO4: A (R=Y, Gd, La; A=Sm3+Er3+ x=0, 0.5, 1) thin films prepared by pechini sol-gel process

Thin film phosphors with compositions of RP1-xVxO4: A (R = Y, Gd, La; A = Sm3+, Et3+; x = 0, 0.5, 1) have been prepared by a Pechini sol-gel process. X-Ray diffraction, atomic force microscopy (AFM), photoluminescence excitation and emission spectra were utilized to characterize the thin film phosphors. The results of XRD showed that a solid solution formed in YVxP1-xO4: A film series from x = 0 to x = 1 with zircon structure, which also held for GdVO4: A film. However, LaVO4: A film crystallized with a different structure, monazite. AFM study revealed that the phosphor films consisted of homogeneous particles ranging from 90 to 400 nm depending on the compositions. Upon short ultraviolet excitation, the films exhibit the characteristic Sm(3+ 4)G(5/2)-H-6(J) (J=5/2, 7/2, 9/2) emission in the red region and Er3+ H-2(11/2), S-4(3/2)-I-4(15/2) emission in the green region, respectively With the increase of x values in YVxP1-xO4: SM3+ (Er3+) films, the emission intensity Of SM3+ (Er3+) increases due to the increase of energy transfer probability from VO43- to Sm3+ (Er3+). Due to the structural effects, the Sm3+ (Er3+) shows similar spectral properties in YVO4 and GdVO4 films, which are much different from those in LaVO4 film.

La_(0.5)R_(0.5)Ba_2Cu_3O_7,Pr_(0.5)R_(0.5)Ba_2Cu_3O_7以及RBa_2Cu_3O_7(R=稀土)的键共价性计算

使用复杂晶体化学键理论计算了La0 .5R0 .5Ba2 Cu3O7(R =Pr,Nd ,Sm ,Eu ,Gd ,Dy ,Y ,Ho,Er,Tm ,Yb ,Lu) (La-R12 3) ,Pr0 .5R0 .5Ba2 Cu3O7(R =La ,Nd ,Sm ,Eu ,Gd ,Dy ,Ho ,Y ,Er,Tm ,Yb ,Lu) (Pr -R12 3)以及RBa2 Cu3O7(R =La ,Pr,Nd ,Sm ,Eu ,Gd ,Dy ,Ho ,Y ,Er,Tm) (R12 3)中Cu—O键的键共价性 ,结果表明Pr-R12 3,La-R12 3,以及R12 3都应具有超导性 ,而实验结果是La0 .5Pr0 .5Ba2 Cu3O7,R0 .5Pr0 .5Ba2 Cu3O7(R =La,Nd ,Sm ,Eu ,Gd)无超导性 .产生这种矛盾的原因尚不明确 ,需要做进一步的研究.

Hydrothermal synthesis of the two-dimensional coordination polymer {[Fe(phen)(OH)](bta)(0.5)}(n) (phen=1,10-phenanthroline, bta=benzene-1,2,4,5-tetracaboxylate)

The title two-dimensional coordination polymer was synthesised and characterised by X-ray diffraction analysis.

Preparation, characterization of solid solution La4BaCu5-xMnxO13+lambda (x=0-5) and its catalytic activity in the reduction of NO by CO

A series of layered mixed oxides La4BaCu5-xMnxO13+lambda(x = 0-5) was prepared, characterized and used as catalysts for NO+CO reaction. It was found that all the samples were single phase having a structure with five-layered-perovskite. La4BaCu2Mn3O13+lambda showed the highest activity in the title reaction, this could be attributed to the synergetic effect between Cu and Mn. The results of TPR, TPD and excess oxygen investigations confirmed that the Cu ion would be the active center. The displacement of the Cu ion by Mn caused the Cu ion to be more easily reducible and more content of excess oxygen, and it was beneficial to the activity of the catalyst. The reaction mechanism was also proposed.

新的稀土锂钒酸盐[Y_(0.5-x)Li_(1.5)VO_4:(Dy~(3+),Eu~(3+))_x]多波段发光

本文首次报道了新的稀土锂钒酸盐Y_(0.5-x)Li_(1.5)VO_4:(Dy~(3+),Eu~(3+))_x多晶粉末的制备,多波段发光和结构. 样品的制备是采用稀土氧化物(Y_2O_3Dy_2O_3和Eu_2O_3)纯度为99.99％与光谱纯的V_2O_5和Li_2CO_3按化学计量比混匀,在

La_(0.5)Sr_(0.5)CoO_(3)结构、气敏和导电性的研究

SnO_2,ZnO和Fe_2O_3等气敏元件目前还存在性能不一致、不稳定等缺点.为要寻找更稳定、选择性更好的敏感元件材料,我们用陶瓷工艺合成了钙钛矿型La_(0.5)Sr_(0.5)CoO_3复合氧化物.用x-射线衍射法测量了La_(0.5)Sr_(0.5)CoO_3的样品,其结构属于立方晶系,

Sm_(0.5)Sr_(0.5)CoO_3酒精检测仪的研制

本文叙述了稀土 Sm_(0.5)Sr_(0.5)CoO_3气敏半导体的制造、结构、探头的构造、管芯的制造工艺,整机的等效线路及原理,元件的特性曲线、模拟实验及作用机理。试验表明:该机灵敏度高、选择性好、比较稳定、响应和恢复时间快,可作为检测司机酒后开车造成的事故。

Effect of 0.5 wt % Cu addition in Sn–3.5% Ag solder on the dissolution rate of Cu metallization

The dissolution of thin film under-bump-metallization (UBM) by molten solder has been one of the most serious processing problems in electronic packaging technology. Due to a higher melting temperature and a greater Sn content, a molten lead-free solder such as eutectic SnAg has a faster dissolution rate of thin film UBM than the eutectic SnPb. The work presented in this paper focuses on the role of 0.5 wt % Cu in the base Sn–3.5%Ag solder to reduce the dissolution of the Cu bond pad in ball grid array applications. We found that after 0.5 wt % Cu addition, the rate of dissolution of Cu in the molten Sn–3.5%Ag solder slows down dramatically. Systematic experimental work was carried out to understand the dissolution behavior of Cu by the molten Sn–3.5%Ag and Sn–3.5%Ag–0.5%Cu solders at 230–250 °C, for different time periods ranging from 1 to 10 min. From the curves of consumed Cu thickness, it was concluded that 0.5 wt % Cu addition actually reduces the concentration gradient at the Cu metallization/molten solder interface which reduces the driving force of dissolution. During the dissolution, excess Cu was found to precipitate out due to heterogeneous nucleation and growth of Cu6Sn5 at the solder melt/oxide interface. In turn, more Cu can be dissolved again. This process continues with time and leads to more dissolution of Cu from the bond pad than the amount expected from the solubility limit, but it occurs at a slower rate for the molten Sn–3.5%Ag–0.5%Cu solder. © 2003 American Institute of Physics.

Structural and magnetic properties of Ni1-xZnxFe2O4 (x=0, 0.5 and 1) nanopowders prepared by sol-gel method

A series of nanostructured Ni-Zn ferrites Ni1-xZnxFe2O4 (x=0, 0.5 and 1) with a grain size from 24 to 65 nm have been prepared with a sol-gel method. The effect of composition and sintering temperature on morphology, magnetic properties, Curie temperature, specific heating rate at 295 kHz and hysteresis loss have been studied. The highest coercivity of 50 and 40 Oe, were obtained for NiFe2O4 and Ni0.5Zn0.5Fe2O4 samples with the grain size of 35 and 29 nm, respectively. The coercivity of Ni and Ni-Zn mixed ferrites decreased with temperature. The Bloch exponent was 1.5 for all samples. As the grain size increased, the Curie temperature of NiFe2O4 increased from 849 to 859 K. The highest saturation magnetization of 70 emu/g at 298 K and the highest specific heating rate of 1.6 K/s under radiofrequency heating at 295 kHz were observed over NiFe2O4 calcined at 1073 K. Both the magnitude of the hysteresis loss and the temperature dependence of the loss are influenced by the sintering temperature and composition.

Studies of the Room-Temperature Multiferroic Pb(Fe0.5Ta0.5)0.4(Zr0.53Ti0.47)0.6O3: Resonant Ultrasound Spectroscopy, Dielectric, and Magnetic Phenomena

Recently, lead iron tantalate/lead zirconium titanate (PZTFT) was demonstrated to possess large, but unreliable, magnetoelectric coupling at room temperature. Such large coupling would be desirable for device applications but reproducibility would also be critical. To better understand the coupling, the properties of all 3 ferroic order parameters, elastic, electric, and magnetic, believed to be present in the material across a range of temperatures, are investigated. In high temperature elastic data, an anomaly is observed at the orthorhombic mm2 to tetragonal 4mm transition, Tot = 475 K, and a softening trend is observed as the temperature is increased toward 1300 K, where the material is known to become cubic. Thermal degradation makes it impos- sible to measure elastic behavior up to this temperature, however. In the low temperature region, there are elastic anomalies near ≈40 K and in the range 160–245 K. The former is interpreted as being due to a magnetic ordering transition and the latter is interpreted as a hysteretic regime of mixed rhom- bohedral and orthorhombic structures. Electrical and magnetic data collected below room temperature show anomalies at remarkably similar temperature ranges to the elastic data. These observations are used to suggest that the three order parameters in PZTFT are strongly coupled.

One-dimensional porous La0.5Sr0.5CoO2.91 nanotubes as a highly efficient electrocatalyst for rechargeable lithium-oxygen batteries

The electrochemical performance of one-dimensional porous La_0.5Sr_0.5CoO_2.91 nanotubes as a cathode catalyst for rechargeable nonaqueous lithium-oxygen (Li-O₂) batteries is reported here for the first time. In this study, one-dimensional porous La_0.5Sr_0.5CoO_2.91 nanotubes were prepared by a simple and efficient electrospinning technique. These materials displayed an initial discharge capacity of 7205 mAh g^-1 with a plateau at around 2.66 V at a current density of 100 mA g^-1. It was found that the La_0.5Sr_0.5CoO_2.91 nanotubes promoted both oxygen reduction and oxygen evolution reactions in alkaline media and a nonaqueous electrolyte, thereby improving the energy and coulombic efficiency of the Li-O₂ batteries. The cyclability was maintained for 85 cycles without any sharp decay under a limited discharge depth of 1000 mAh g^-1, suggesting that such a bifunctional electrocatalyst is a promising candidate for the oxygen electrode in Li-O₂ batteries.

Investigation into the effect of molybdenum-site substitution on the performance of Sr2Fe1.5Mo0.5O6-δ for intermediate temperature solid oxide fuel cells

In this paper, niobium doping is evaluated as a means of enhancing the electrochemical performance of a Sr₂Fe_1.5Mo_0.5O_6-δ (SFM) perovskite structure cathode material for intermediate temperature solid oxide fuel cells (IT-SOFCs) applications. As the radius of Nb approximates that of Mo and exhibits +4/+5 mixed valences, its substitution is expected to improve material performance. A series of Sr₂Fe_1.5Mo_0.5-xNb_xO_6-δ (x = 0.05, 0.10, 0.15, 0.20) cathode materials are prepared and the phase structure, chemical compatibility, microstructure, electrical conductivity, polarization resistance and power generation are systematically characterized. Among the series of samples, Sr₂Fe_1.5Mo_0.4Nb_0.10O_6-δ (SFMNb_0.10) exhibits the highest conductivity value of 30 S cm^-1 at 550°C, and the lowest area specific resistance of 0.068 Ω cm² at 800°C. Furthermore, an anode-supported single cell incorporating a SFMNb_0.10 cathode presents a maximum power density of 1102 mW cm^-2 at 800°C. Furthermore no obvious performance degradation is observed over 15 h at 750°C with wet H₂(3% H₂O) as fuel and ambient air as the oxidant. These results demonstrate that SFMNb shows great promise as a novel cathode material for IT-SOFCs.

Investigation into the effect of Fe-site substitution on the performance of Sr2Fe1.5Mo0.5O6-δ anodes for SOFCs

Ni-substituted Sr₂Fe_1.5-xNi_xMo_0.5O_6-δ (SFNM) materials have been investigated as anode catalysts for intermediate temperature solid oxide fuel cells. Reduced samples (x = 0.05 and 0.1) maintained the initial perovskite structure after reduction in H₂, while metallic nickel particles were detected on the grain surface for x = 0.2 and 0.3 using transmission electron microscopy. Temperature programmed reduction results indicate that the stable temperature for SFNM samples under reduction conditions decreases with Ni content. In addition, X-ray photoelectron spectroscopy analysis suggests that the incorporation of Ni affects the conductivity of SFNM through changing the ratios of Fe³⁺/Fe²⁺ and Mo⁶⁺/Mo⁵⁺. Sr₂Fe_1.4Ni_0.1Mo_0.5O_6-δ shows the highest electrical conductivity of 20.6 S cm^-1 at 800 °C in H₂. The performance of this anode was further tested with electrolyte-supported cells, giving 380 mW cm^-2 at 750 °C in H₂, hence demonstrating that Ni doping in the B-site is beneficial for Sr₂Fe_1.5Mo_0.5O_6-δ anode performance.