Improved Employment Data for Transportation Planning, 1998

Transportation planners typically use census data or small sample surveys to help estimate work trips in metropolitan areas. Census data are cheap to use but are only collected every 10 years and may not provide the answers that a planner is seeking. On the other hand, small sample survey data are fresh but can be very expensive to collect. This project involved using database and geographic information systems (GIS) technology to relate several administrative data sources that are not usually employed by transportation planners. These data sources included data collected by state agencies for unemployment insurance purposes and for drivers licensing. Together, these data sources could allow better estimates of the following information for a metropolitan area or planning region: · Locations of employers (work sites); · Locations of employees; · Travel flows between employees’ homes and their work locations. The required new employment database was created for a large, multi-county region in central Iowa. When evaluated against the estimates of a metropolitan planning organization, the new database did allow for a one to four percent improvement in estimates over the traditional approach. While this does not sound highly significant, the approach using improved employment data to synthesize home-based work (HBW) trip tables was particularly beneficial in improving estimated traffic on high-capacity routes. These are precisely the routes that transportation planners are most interested in modeling accurately. Therefore, the concept of using improved employment data for transportation planning was considered valuable and worthy of follow-up research.

Validação de modelo para predição do potencial produtivo de trigo com sensor óptico ativo

O objetivo deste trabalho foi validar um modelo baseado no índice de vegetação por diferença normalizada (NDVI), para a predição da variabilidade espacial da biomassa acumulada na parte aérea e da produtividade de grãos de trigo. Foram realizadas leituras georreferenciadas de NDVI e biomassa, no final do afilhamento, e produtividade. O modelo proposto permitiu relacionar classes de variabilidade espacial do NDVI e da biomassa, com 81% de correspondência entre elas. Entretanto, a relação entre as classes de variabilidade espacial da produtividade e do NDVI foi menor, com 48% de correspondência.

Sensor óptico no auxílio à recomendação de adubação nitrogenada em cana-de-açúcar

O objetivo deste trabalho foi avaliar o potencial de um sensor óptico ativo terrestre como auxiliar na recomendação da aplicação de nitrogênio em taxa variável, na cultura da cana-de-açúcar. Foram instalados experimentos em delineamento de blocos ao acaso, com uso de diferentes doses de N (0, 50, 100, 150 e 200 kg ha-1). A resposta da cana-de-açúcar ao N foi avaliada por diferentes métodos - sensor óptico, clorofilômetro e teor foliar de N -, quando a altura média dos colmos atingiu 0,2, 0,4 e 0,6 m. Observou-se baixa correlação entre o teor foliar de N e a quantidade de clorofila nas folhas mensuradas por clorofilômetro. Portanto, essas características foram insuficientes para avaliar a eficiência do sensor óptico, uma vez que os valores mensurados se elevaram conforme o aumento da dose de N. A estratégia de recomendação com base na resposta da cultura, estimada pelo sensor óptico em faixa de cana-de-açúcar que recebeu a dose adequada de N, mostrou-se mais condizente com a produtividade obtida. O sensor óptico é ferramenta útil para auxiliar na recomendação de N para a cultura da cana-de-açúcar, ao se considerar a variabilidade espacial da sua demanda.

Imagens multipolarizadas do sensor Palsar/Alos na discriminação das fases fenológicas da cana‑de‑açúcar

O objetivo deste trabalho foi avaliar o potencial das imagens multipolarizadas do sensor‑radar Palsar/Alos em diferenciar as fases fenológicas da cana‑de‑açúcar. Valores digitais de quatro imagens do sensor, dos meses de fevereiro, maio, agosto e outubro de 2008, com polarizações HH (emissão e recebimento de onda na polarização horizontal) e HV (emissão de onda na polarização horizontal e recebimento na vertical), foram convertidos para coeficientes de retroespalhamento (σ°), para a análise de dados de cana‑de‑açúcar, cultivadas em talhões na região nordeste do Estado de São Paulo. Foram selecionadas três variedades, em diferentes estágios fenológicos: RB85‑5156, seis talhões; RB86‑7515, dez talhões; e RB92‑5345, dez talhões. As diferenças entre as fases fenológicas foram avaliadas para cada uma das variedades e, também, entre as variedades. A utilização simultânea ou não dos dados do sensor Palsar/Alos, obtidos em duas polarizações, foi capaz de discriminar as diferentes fases de crescimento da cana‑de‑açúcar, com exceção da fase de crescimento dos colmos e a fase de maturação, em que não foi observada diferença significativa.

Séries temporais de NDVI do sensor SPOT Vegetation e algoritmo SAM aplicados ao mapeamento de cana‑de‑açúcar

O objetivo deste trabalho foi avaliar o mapeamento de área de cana‑de‑açúcar por meio de série temporal, de seis anos de dados do índice de vegetação por diferença normalizada (NDVI), oriundos do sensor Vegetation, a bordo do satélite "système pour l'observation de la Terre" (SPOT). Três classes de cobertura do solo (cana‑de‑açúcar, pasto e floresta), do Estado de São Paulo, foram selecionadas como assinaturas espectro‑temporais de referência, que serviram como membros extremos ("endmembers") para classificação com o algoritmo "spectral angle mapper" (SAM). A partir desta classificação, o mapeamento da área de cana‑de‑açúcar foi realizado com uso de limiares na imagem-regra do SAM, gerados a partir dos valores dos espectros de referência. Os resultados mostram que o algoritmo SAM pode ser aplicado a séries de dados multitemporais de resolução moderada, o que permite eficiente mapeamento de alvo agrícola em escala mesorregional. Dados oficiais de áreas de cana‑de‑açúcar, para as microrregiões paulistas, apresentam boa correlação (r² = 0,8) com os dados obtidos pelo método avaliado. A aplicação do algoritmo SAM mostrou ser útil em análises temporais. As séries temporais de NDVI do sensor SPOT Vegetation podem ser utilizadas para mapeamento da área de cana‑de‑açúcar em baixa resolução.

The CerdàPlan for the Extension of Barcelona: A Constructivist Analysis of a Town-planning Controversy

Peer-reviewed

Computer-assisted two-dimensional preoperative planning for total hip arthroplasty: clinical evaluation.

The purpose of this study is to clinically validate a new two-dimensional preoperative planning software for cementless total hip arthroplasty (THA). Manual and two-dimensional computer-assisted planning were compared by an independent observer for each of the 30 patients with osteoarthritis who underwent THA. This study showed that there were no statistical differences between the results of both preoperative plans in terms of stem size and neck length (<1 size) and hip rotation center position (<5 mm). Two-dimensional computer-assisted preoperative planning provided successful results comparable to those using the manual procedure, thereby allowing the surgeon to simulate various stem designs easily.

Offering planning with support of roadmapping in project business

Tämän tutkielman tavoitteena on tutkia kuinka roadmapping-tekniikkaa voidaan käyttää tarjonnan suunnittelun tukena uusien tuotteiden valmistamisen yhteydessä. Työ koostuu teoreettisesta ja käytännönläheisestä osasta. Teoreettinen runko on luotu selventämään kuinka tämän hetkisen tutkimus- ja kehitys projektit lopulta muodostavat tulevaisuuden tarjoaman. Menestyksekkään tuotetarjoaman luominen vaatii, sekä uusien teknologioiden kehittämistä, että markkinoilla olevien asiakkaiden tarpeiden ymmärtämistä. Asiakassuuntaisten tuotteiden kehittäminen vaatii toimintaympäristöstä ja asiakasrajapinnasta tulevien signaalien tunnistamista ja niiden ohjaamista tuote- ja teknologia platformeille. Strategia luodaan tukemaan päätöksentekoa prosessin eri vaiheissa. Yrityskohtainen osio koostuu analyysistä, joka on tehty teetetyn kyselyn ja haas-tattelujen pohjalta. Osana analyysia ovat Major project-yksikön tämänhetkinen tarjonnansuunnitteluprosessi, strategian soveltaminen, informaation kerääminen ja priorisointi, portfolionhallinta ja roadmap-tekniikan käyttö. Ratkaisussa on esitet-ty tarjonnan suunnitteluprosessi ja siihen liittyvät kriittiset komponentit. Roadmapping-tekniikkaaon luotu yhdistämään toimintaympäristö, tuotteet ja teknologia toisiinsa. Toimintaympäristö ja tuotteet on yhdistetty myös linked-grids-tekniikan avulla.

Measurement with an automated oscillometric wrist device with position sensor leads to lower values than measurements obtained with an automated oscillometric arm device from the same manufacturer in elderly persons.

OBJECTIVE: Home blood pressure (BP) monitoring is recommended by several clinical guidelines and has been shown to be feasible in elderly persons. Wrist manometers have recently been proposed for such home BP measurement, but their accuracy has not been previously assessed in elderly patients. METHODS: Forty-eight participants (33 women and 15 men, mean age 81.3±8.0 years) had their BP measured with a wrist device with position sensor and an arm device in random order in a sitting position. RESULTS: Average BP measurements were consistently lower with the wrist than arm device for systolic BP (120.1±2.2 vs. 130.5±2.2 mmHg, P<0.001, means±SD) and diastolic BP (66.0±1.3 vs. 69.7±1.3 mmHg, P<0.001). Moreover, a 10 mmHg or greater difference between the arm and wrist device was observed in 54.2 and 18.8% of systolic and diastolic measures, respectively. CONCLUSION: Compared with the arm device, the wrist device with position sensor systematically underestimated systolic as well as diastolic BP. The magnitude of the difference is clinically significant and questions the use of the wrist device to monitor BP in elderly persons. This study points to the need to validate BP measuring devices in all age groups, including in elderly persons.

Short-term Hydropower Planning System

The Thesis gives a decision support framework that has significant impact on the economic performance and viability of a hydropower company. The studyaddresses the short-term hydropower planning problem in the Nordic deregulated electricity market. The basics of the Nordic electricity market, trading mechanisms, hydropower system characteristics and production planning are presented in the Thesis. The related modelling theory and optimization methods are covered aswell. The Thesis provides a mixed integer linear programming model applied in asuccessive linearization method for optimal bidding and scheduling decisions inthe hydropower system operation within short-term horizon. A scenario based deterministic approach is exploited for modelling uncertainty in market price and inflow. The Thesis proposes a calibration framework to examine the physical accuracy and economic optimality of the decisions suggested by the model. A calibration example is provided with data from a real hydropower system using a commercial modelling application with the mixed integer linear programming solver CPLEX.

Sugarcane response to nitrogen rates, measured by a canopy reflectance sensor

Abstract:The objective of this work was to evaluate whether a canopy sensor is capable of estimating sugarcane response to N, as well as to propose strategies for handling the data generated by this device during the decision-making process for crop N fertilization. Four N rate-response experiments were carried out, with N rates varying from 0 to 240 kg ha-1. Two evaluations with the canopy sensor were performed when the plants reached average stalk height of 0.3 and 0.5 m. Only two experiments showed stalk yield response to N rates. The canopy sensor was able to identify the crop response to different N rates and the relationship of the nutrient with sugarcane yield. The response index values obtained from the canopy sensor readings were useful in assessing sugarcane response to the applied N rate. Canopy reflectance sensors can help to identify areas responsive to N fertilization and, therefore, improve sugarcane fertilizer management.

Cutting of Frozen Wood

The objective of this master's thesis was to develop a system for measuring the cutting forces of frozen wood. In northern parts of the world cuttingof frozen wood is one of the major problem. During winter and early spring the temperature inside the wood cells will fall below Zero degrees that strongly influences on the properties of the wood. These variations of properties will effects on the blade nomenclature while cutting the frozen wood. However the end results will cause uneven cutting forces. Cutting forces, Chip formation, wearing of the blade and the quality of the machined surface are difficult task. In this project we are attempting to find the variation of cutting forces and properties of frozen wood at four different temperatures (-20 , -10, 0 and + 10 degrees). The linear planning machine was used for measuring the cuttingforces. The cutting was done parallel to the long axis of wood due to the nature of pine wood and the structure of the plane. A considerable amount of work andtime was used for collecting and processing the numerical information from the sensors of the measuring system. There were some alterations suggested to the construction of the plane and the sensor system.

Simulació de xarxes WSN (Wireless Sensor Network) per a la detecció d'incendis

Trabajo de final de carrera enfocado a la simulación de una WSN (Wireless Sensors Networks) mediante el programa Contiki 2.7 y el SO Ubuntu. La idea global del proyecto es conseguir simular un entorno con nodos sensores y, a posteriori, comprobar su correcto funcionamiento en motas reales, comprobando los resultados obtenidos en ambos entornos. De esta manera se puede facilitar la puesta en marcha de este tipo de redes inalámbricas en una aplicación real.

Planning and control of internal development projects in a fast changing environment: Case study

Tutkimuksen tarkoituksena on kuvata ja ymmärtää kuinka sisäisiä kehityshankkeita voidaan hallita onnistuneesti kun toimitaan nopeasti muuttuvassa ympäristössä. Tutkimus kuvailee etenkin projekteille tärkeitä menestymistekijöitä, kuten suunnittelu, kontrollointi ja päätöksenteko. Tutkimus selvittää yleisimmät ongelma-alueet case-organisaation sisäisten kehityshankkeiden hallinnassa. Tutkimus on luonteeltaan laadullinen tutkimus, jossa tutkimusmenetelmänä on käytetty tapaustutkimusta. Empiirisessa osassa käsittellään case-organisaation sisäisiä informaatioteknologia-hankkeita (IT) ja uusien konseptien kehityshankkeita (NCD). iSisäisten kehityshankkeiden erilaisuuden ymmärtäminen oli tutkimuksen tärkein tulos. Tutkimuksen empiirinen osio osoitti sen, että epävarmuudella on erittäin suuri vaikutus projektihallintaan sekä projektin kontrollointiin. Case-organisaation IT-projektien onnistuminen riippuu organisaatiomuu-toksen onnistumisesta. Asiakkaisiin ja markkinoihin liittyvät epävarmuudet ovat vaikuttavimmat NCD projektien epävarmuuksista. Näillä epävarmuuk-sil­la on vaikutusta projektihallintaan jonka myötä NCD projektit juuttuvat useim­mi­ten noidankehiin tai ne lopetetaan jo aikaisessa vaiheessa.

Real-time monitoring of protein conformational changes using a nano-mechanical sensor.

Proteins can switch between different conformations in response to stimuli, such as pH or temperature variations, or to the binding of ligands. Such plasticity and its kinetics can have a crucial functional role, and their characterization has taken center stage in protein research. As an example, Topoisomerases are particularly interesting enzymes capable of managing tangled and supercoiled double-stranded DNA, thus facilitating many physiological processes. In this work, we describe the use of a cantilever-based nanomotion sensor to characterize the dynamics of human topoisomerase II (Topo II) enzymes and their response to different kinds of ligands, such as ATP, which enhance the conformational dynamics. The sensitivity and time resolution of this sensor allow determining quantitatively the correlation between the ATP concentration and the rate of Topo II conformational changes. Furthermore, we show how to rationalize the experimental results in a comprehensive model that takes into account both the physics of the cantilever and the dynamics of the ATPase cycle of the enzyme, shedding light on the kinetics of the process. Finally, we study the effect of aclarubicin, an anticancer drug, demonstrating that it affects directly the Topo II molecule inhibiting its conformational changes. These results pave the way to a new way of studying the intrinsic dynamics of proteins and of protein complexes allowing new applications ranging from fundamental proteomics to drug discovery and development and possibly to clinical practice.