The pH-dependent phase distribution of wood pitch components in papermaking processes

Wood contains only a very small amount of lipophilic extractives, commonly known as wood pitch. The pitch is known to cause severe problems in papermaking processes. The amount of pitch in process waters can be decreased by seasoning of the raw material prior to pulping, pulp washing, removal of pitch by flotation, adsorption of pitch onto various mineral surfaces, and retention of pitch to the fibre material by cationic polymers. The aim of this study was to determine the influence of pH on some of the methods used for pitch control. Experiments were performed using laboratory-made wood pitch emulsions with varying pH, salt concentration, hemicellulose concentration and pitch composition. These emulsions were used to study the phase distribution of resin and fatty acids, the colloidal stability of pitch with and without steric stabilisation by galactoglucomannans, and the interactions between wood pitch and mineral particles. Purification of unbleached and peroxidebleached mill process water was performed by froth flotation in combination with a foaming agent. The distribution of resin and fatty acids (RFAs) between colloidal pitch droplets and the water phase was very dependent on pH. At pH 3, almost all of the RFAs were attached to the pitch droplets, while increasing the pH led to increasing concentration of dissolved RFAs in the water phase. The presence of salt shifted the release of RFAs towards higher pH, while lower ratio of neutral pitch in the emulsion resulted in release of RFAs at lower pH. It was also seen that the dissolution and adsorption of RFAs at sudden pHchanges takes place very quickly. Colloidal pitch was more stable against electrolyte-induced aggregation at higher pH, due to its higher anionic charge. The concentration of cationic polymers needed to aggregate colloidal pitch also increased with increasing pH. The surface characteristics of solid particles, such as amount of charged groups, were very important for understanding their interactions with colloidal wood pitch. Water-soluble galactoglucomannans stabilised the colloidal pitch sterically against aggregation, but could not completely prevent interactions between wood pitch and hydrophilic particles. Froth flotation of unbleached and peroxidebleached process water showed that the pitch could be removed more effectively and selectively at low pH, compared to at neutral pH. The pitch was removed more effectively, using lower concentrations of foaming agent, from peroxide-bleached water than from unbleached water. The results show that pH has a major impact on various pulping and papermaking processes. It determines the anionic charge of the colloidal pitch and the solubility of certain pitch components. Because of this, the pH influences the effectiveness of pitch retention and removal of pitch. The results indicate that pitch problems could be diminished by acknowledging the importance of pH in various papermaking processes.

Roles of leadership in complex environments : Enhancing Knowledge Flows in Organisational Constellations through Practice-Based Innovation Processes

Global challenges, complexity and continuous uncertainty demand development of leadership approaches, employees and multi-organisation constellations. Current leadership theories do not sufficiently address the needs of complex business environments. First of all, before successful leadership models can be applied in practice, leadership needs to shift from the industrial age to the knowledge era. Many leadership models still view leadership solely through the perspective of linear process thinking. In addition, there is not enough knowledge or experience in applying these newer models in practice. Leadership theories continue to be based on the assumption that leaders possess or have access to all the relevant knowledge and capabilities to decide future directions without external advice. In many companies, however, the workforce consists of skilled professionals whose work and related interfaces are so challenging that the leaders cannot grasp all the linked viewpoints and cross-impacts alone. One of the main objectives of this study is to understand how to support participants in organisations and their stakeholders to, through practice-based innovation processes, confront various environments. Another aim is to find effective ways of recognising and reacting to diverse contexts, so companies and other stakeholders are better able to link to knowledge flows and shared value creation processes in advancing joint value to their customers. The main research question of this dissertation is, then, to seek understanding of how to enhance leadership in complex environments. The dissertation can, on the whole, be characterised as a qualitative multiple-case study. The research questions and objectives were investigated through six studies published in international scientific journals. The main methods applied were interviews, action research and a survey. The empirical focus was on Finnish companies, and the research questions were examined in various organisations at the top levels (leaders and managers) and bottom levels (employees) in the context of collaboration between organisations and cooperation between case companies and their client organisations. However, the emphasis of the analysis is the internal and external aspects of organisations, which are conducted in practice-based innovation processes. The results of this study suggest that the Cynefin framework, complexity leadership theory and transformational leadership represent theoretical models applicable to developing leadership through practice-based innovation. In and of themselves, they all support confronting contemporary challenges, but an implementable method for organisations may be constructed by assimilating them into practice-based innovation processes. Recognition of diverse environments, their various contexts and roles in the activities and collaboration of organisations and their interest groups is ever-more important to achieving better interaction in which a strategic or formal status may be bypassed. In innovation processes, it is not necessarily the leader who is in possession of the essential knowledge; thus, it is the role of leadership to offer methods and arenas where different actors may generate advances. Enabling and supporting continuous interaction and integrated knowledge flows is of crucial importance, to achieve emergence of innovations in the activities of organisations and various forms of collaboration. The main contribution of this dissertation relates to applying these new conceptual models in practice. Empirical evidence on the relevance of different leadership roles in practice-based innovation processes in Finnish companies is another valuable contribution. Finally, the dissertation sheds light on the significance of combining complexity science with leadership and innovation theories in research.

Value co-creation in gaming the industry: A qualitative research on virtual discussion forums

This study discusses the procedures of value co-creation that persist in gaming industry. The purpose of this study was to identify the procedures that persist in current video gaming industry which answers the main research problem how value is co-created in video gaming industry followed by three sub questions: (i) What is value co-creation in gaming industry? (ii) Who participates in value co-creation in gaming industry? (iii) What are the procedures that are involved in value co-creation in gaming industry? The theoretical background of the study consists of literature relating to the theory of marketing i.e., notion of value, conventional understanding of value creation, value chain, co-creation approach, co-production approach. The research adopted qualitative research approach. As a platform of relationship researcher used web 2.0 tool interface. Data were collected from the social networks and netnography method was applied for analyzing them. Findings show that customer and company both co-create optimum level of value while they interact with each other and within the customers as well. However mostly the C2C interaction, discussions and dialogues threads that emerged around the main discussion facilitated to co-create value. In this manner, companies require exploiting and further motivating, developing and supporting the interactions between customers participating in value creation. Hierarchy of value co-creation processes is the result derived from the identified challenges of value co-creation approach and discussion forums data analysis. Overall three general sets and seven topics were found that explored the phenomenon of customer to customer (C2C) and business to customer (B2C) interaction/debating for value co-creation through user generated contents. These topics describe how gamer contributes and interacts in co-creating value along with companies. A methodical quest in current research literature acknowledged numerous evolving flows of value in this study. These are general management perspective, new product development and innovation, virtual customer environment, service science and service dominant logic. Overall the topics deliver various realistic and conceptual implications for using and handling gamers in social networks for augmenting customers’ value co-creation process.

It’s a workflow engine. It’s working with linked data. It’s repository! – Supporting electronic thesis related processes in University of Helsinki library

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

E-thesis repository – processes and data

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

The supermassive binary black hole system OJ287

Abstract This doctoral thesis concerns the active galactic nucleus (AGN) most often referred to with the catalogue number OJ287. The publications in the thesis present new discoveries of the system in the context of a supermassive binary black hole model. In addition, the introduction discusses general characteristics of the OJ287 system and the physical fundamentals behind these characteristics. The place of OJ287 in the hierarchy of known types of AGN is also discussed. The introduction presents a large selection of fundamental physics required to have a basic understanding of active galactic nuclei, binary black holes, relativistic jets and accretion disks. Particularly the general relativistic nature of the orbits of close binaries of supermassive black holes is explored with some detail. Analytic estimates of some of the general relativistic effects in such a binary are presented, as well as numerical methods to calculate the effects more precisely. It is also shown how these results can be applied to the OJ287 system. The binary orbit model forms the basis for models of the recurring optical outbursts in the OJ287 system. In the introduction, two physical outburst models are presented in some detail and compared. The radiation hydrodynamics of the outbursts are discussed and optical light curve predictions are derived. The precursor outbursts studied in Paper III are also presented, and tied into the model of OJ287. To complete the discussion of the observable features of OJ287, the nature of the relativistic jets in the system, and in active galactic nuclei in general, is discussed. Basic physics of relativistic jets are presented, with additional detail added in the form of helical jet models. The results of Papers II, IV and V concerning the jet of OJ287 are presented, and their relation to other facets of the binary black hole model is discussed. As a whole, the introduction serves as a guide, though terse, for the physics and numerical methods required to successfully understand and simulate a close binary of supermassive black holes. For this purpose, the introduction necessarily combines a large number of both fundamental and specific results from broad disciplines like general relativity and radiation hydrodynamics. With the material included in the introduction, the publications of the thesis, which present new results with a much narrower focus, can be readily understood. Of the publications, Paper I presents newly discovered optical data points for OJ287, detected on archival astronomical plates from the Harvard College Observatory. These data points show the 1900 outburst of OJ287 for the first time. In addition, new data points covering the 1913 outburst allowed the determination of the start of the outburst with more precision than was possible before. These outbursts were then successfully numerically modelled with an N-body simulation of the OJ287 binary and accretion disc. In Paper II, mechanisms for the spin-up of the secondary black hole in OJ287 via interaction with the primary accretion disc and the magnetic fields in the system are discussed. Timescales for spin-up and alignment via both processes are estimated. It is found that the secondary black hole likely has a high spin. Paper III reports a new outburst of OJ287 in March 2013. The outburst was found to be rather similar to the ones reported in 1993 and 2004. All these outbursts happened just before the main outburst season, and are called precursor outbursts. In this paper, a mechanism was proposed for the precursor outbursts, where the secondary black hole collides with a gas cloud in the primary accretion disc corona. From this, estimates of brightness and timescales for the precursor were derived, as well as a prediction of the timing of the next precursor outburst. In Paper IV, observations from the 2004–2006 OJ287 observing program are used to investigate the existence of short periodicities in OJ287. The existence of a _50 day quasiperiodic component is confirmed. In addition, statistically significant 250 day and 3.5 day periods are found. Primary black hole accretion of a spiral density wave in the accretion disc is proposed as the source of the 50 day period, with numerical simulations supporting these results. Lorentz contracted jet re-emission is then proposed as the reason for the 3.5 day timescale. Paper V fits optical observations and mm and cm radio observations of OJ287 with a helical jet model. The jet is found to have a spine–sheath structure, with the sheath having a much lower Lorentz gamma factor than the spine. The sheath opening angle and Lorentz factor, as well as the helical wavelength of the jet are reported for the first time. Tiivistelmä Tässä väitöskirjatutkimuksessa on keskitytty tutkimaan aktiivista galaksiydintä OJ287. Väitöskirjan osana olevat tieteelliset julkaisut esittelevät OJ287-systeemistä saatuja uusia tuloksia kaksoismusta-aukkomallin kontekstissa. Väitöskirjan johdannossa käsitellään OJ287:n yleisiä ominaisuuksia ja niitä fysikaalisia perusilmiöitä, jotka näiden ominaisuuksien taustalla vaikuttavat. Johdanto selvittää myös OJ287-järjestelmän sijoittumisen aktiivisten galaksiytimien hierarkiassa. Johdannossa käydään läpi joitakin perusfysiikan tuloksia, jotka ovat tarpeen aktiivisten galaksiydinten, mustien aukkojen binäärien, relativististen suihkujen ja kertymäkiekkojen ymmärtämiseksi. Kahden toisiaan kiertävän mustan aukon keskinäisen radan suhteellisuusteoreettiset perusteet käydään läpi yksityiskohtaisemmin. Johdannossa esitetään joitakin analyyttisiä tuloksia tällaisessa binäärissä havaittavista suhteellisuusteoreettisista ilmiöistä. Myös numeerisia menetelmiä näiden ilmiöiden tarkempaan laskemiseen esitellään. Tuloksia sovelletaan OJ287-systeemiin, ja verrataan havaintoihin. OJ287:n mustien aukkojen ratamalli muodostaa pohjan systeemin toistuvien optisten purkausten malleille. Johdannossa esitellään yksityiskohtaisemmin kaksi fysikaalista purkausmallia, ja vertaillaan niitä. Purkausten säteilyhydrodynamiikka käydään läpi, ja myös ennusteet purkausten valokäyrille johdetaan. Johdannossa esitellään myös Julkaisussa III johdettu prekursoripurkausten malli, ja osoitetaan sen sopivan yhteen OJ287:n binäärimallin kanssa. Johdanto esittelee myös relativististen suihkujen fysiikkaa sekä OJ287- systeemiin liittyen että aktiivisten galaksiydinten kontekstissa yleisesti. Relativististen suihkujen perusfysiikka esitellään, kuten myös malleja kierteisistä suihkuista. Julkaisujen II, IV ja V OJ287-systeemin suihkuja koskevat tulokset esitellään binäärimallin kontekstissa. Kokonaisuutena johdanto palvelee suppeana oppaana, joka esittelee tarvittavan fysiikan ja tarpeelliset numeeriset menetelmät mustien aukkojen binäärijärjestelmän ymmärtämiseen ja simulointiin. Tätä tarkoitusta varten johdanto yhdistää sekä perustuloksia että joitakin syvällisempiä tuloksia laajoilta fysiikan osa-alueilta kuten suhteellisuusteoriasta ja säteilyhydrodynamiikasta. Johdannon sisältämän materiaalin avulla väitöskirjan julkaisut, ja niiden esittämät tulokset, ovat hyvin ymmärrettävissä. Väitöskirjan julkaisuista ensimmäinen esittelee uusia OJ287-systeemistä saatuja havaintopisteitä, jotka on paikallistettu Harvardin yliopiston observatorion arkiston valokuvauslevyiltä. OJ287:n vuonna 1900 tapahtunut purkaus nähdään ensimmäistä kertaa näissä havaintopisteissä. Uudet havaintopisteet mahdollistivat myös vuoden 1913 purkauksen alun ajoittamisen tarkemmin kuin aiemmin oli mahdollista. Havaitut purkaukset mallinnettiin onnistuneesti simuloimalla OJ287-järjestelmän mustien aukkojen paria ja kertymäkiekkoa. Julkaisussa II käsitellään mekanismeja OJ287:n sekundäärisen mustan aukon spinin kasvamiseen vuorovaikutuksessa primäärin kertymäkiekon ja systeemin magneettikenttien kanssa. Julkaisussa arvioidaan maksimispinin saavuttamisen ja spinin suunnan vakiintumisen aikaskaalat kummallakin mekanismilla. Tutkimuksessa havaitaan sekundäärin spinin olevan todennäköisesti suuri. Julkaisu III esittelee OJ287-systeemissä maaliskuussa 2013 tapahtuneen purkauksen. Purkauksen havaittiin muistuttavan vuosina 1993 ja 2004 tapahtuneita purkauksia, joita kutsutaan yhteisnimityksellä prekursoripurkaus (precursor outburst). Julkaisussa esitellään purkauksen synnylle mekanismi, jossa OJ287-systeemin sekundäärinen musta aukko osuu primäärisen mustan aukon kertymäkiekon koronassa olevaan kaasupilveen. Mekanismin avulla johdetaan arviot prekursoripurkausten kirkkaudelle ja aikaskaalalle. Julkaisussa johdetaan myös ennuste seuraavan prekursoripurkauksen ajankohdalle. Julkaisussa IV käytetään vuosina 2004–2006 kerättyjä havaintoja OJ287- systeemistä lyhyiden jaksollisuuksien etsintään. Julkaisussa varmennetaan systeemissä esiintyvä n. 50 päivän kvasiperiodisuus. Lisäksi tilastollisesti merkittävät 250 päivän ja 3,5 päivän jaksollisuudet havaitaan. Julkaisussa esitetään malli, jossa primäärisen mustan aukon kertymäkiekossa oleva spiraalitiheysaalto aiheuttaa 50 päivän jaksollisuuden. Mallista tehty numeerinen simulaatio tukee tulosta. Systeemin relativistisen suihkun emittoima aikadilatoitunut säteily esitetään aiheuttajaksi 3,5 päivän jaksollisuusaikaskaalalle. Julkaisussa V sovitetaan kierresuihkumalli OJ287-systeemistä tehtyihin optisiin havaintoihin ja millimetri- sekä senttimetriaallonpituuden radiohavaintoihin. Suihkun rakenteen havaitaan olevan kaksijakoinen ja koostuvan ytimestä ja kuoresta. Suihkun kuorella on merkittävästi pienempi Lorentzin gamma-tekijä kuin suihkun ytimellä. Kuoren avautumiskulma ja Lorentztekijä sekä suihkun kierteen aallonpituus raportoidaan julkaisussa ensimmäistä kertaa.

Carrier selection and management : A case study on Neste Oil Retail

Service provider selection has been said to be a critical factor in the formation of supply chains. Through successful selection companies can attain competitive advantage, cost savings and more flexible operations. Service provider management is the next crucial step in outsourcing process after the selection has been made. Without proper management companies cannot be sure about the level of service they have bought and they may suffer from service provider's opportunistic behavior. In worst case scenario the buyer company may end up in locked-in situation in which it is totally dependent of the service provider. This thesis studies how the case company conducts its carrier selection process along with the criteria related to it. A model for the final selection is also provided. In addition, case company's carrier management procedures are reflected against recommendations from previous researches. The research was conducted as a qualitative case study on the principal company, Neste Oil Retail. A literature review was made on outsourcing, service provider selection and service provider management. On the basis of the literature review, this thesis ended up recommending Analytic hierarchy process as the preferred model for the carrier selection. Furthermore, Agency theory was seen to be a functional framework for carrier management in this study. Empirical part of this thesis was conducted in the case company by interviewing the key persons in the selection process, making observations and going through documentations related to the subject. According to the results from the study, both carrier selection process as well as carrier management were closely in line with suggestions from literature review. Analytic hierarchy process results revealed that the case company considers service quality as the most important criteria with financial situation and price of service following behind with almost identical weights with each other. Equipment and personnel was seen as the least important selection criterion. Regarding carrier management, the study resulted in the conclusion that the company should consider engaging more in carrier development and working towards beneficial and effective relationships. Otherwise, no major changes were recommended for the case company processes.

Influence of reactant absorption and dissolution in heterogeneous precipitation processes

In this research work, the aim was to investigate the volumetric mass transfer coefficient [kLa] of oxygen in stirred tank in the presence of solid particle experimentally. The kLa correlations as a function of propeller rotation speed and flow rate of gas feed were studied. The O2 and CO2 absorption in water and in solid-liquid suspensions and heterogeneous precipitation of MgCO3 were thoroughly examined. The absorption experiments of oxygen were conducted in various systems like pure water and in aqueous suspensions of quartz and calcium carbonate particles. Secondly, the precipitation kinetics of magnesium carbonate was also investigated. The experiments were performed to study the reactive crystallization with magnesium hydroxide slurry and carbon dioxide gas by varying the feed rates of carbon dioxide and rotation speeds of mixer. The results of absorption and precipitation are evaluated by titration, total carbon (TC analysis), and ionic chromatrography (IC). For calcium carbonate, the particle concentration was varied from 17.4 g to 2382 g with two size fractions: 5 µm and 45-63 µm sieves. The kLa and P/V values of 17.4 g CaCO3 with particle size of 5µm and 45-63 µm were 0.016 s-1 and 2400 W/m3. At 69.9 g concentration of CaCO3, the achieved kLa is 0.014 s-1 with particle size of 5 µm and 0.017 s-1 with particle size of 45 to 63 µm. Further increase in concentration of calcium carbonate, i.e. 870g and 2382g , does not affect volumetric mass transfer coeffienct of oxygen. It could be concluded from absorption results that maximum value of kLa is 0.016 s-1. Also particle size and concentration does affect the transfer rate to some extend. For precipitation experiments, the constant concentration of Mg(OH)2 was 100 g and the rotation speed varied from 560 to 750 rpm, whereas the used feed rates of CO2 were 1 and 9 L/min. At 560 rpm and feed rate of CO2 is 1 L/min, the maximum value of Mg ion and TC were 0.25 mol/litre and 0.12 mol/litre with the residence time of 40 min. When flow rate of CO2 increased to 9 L/min with same 560 rpm, the achieved value of Mg and TC were 0.3 mol/litre and 0.12 mol/L with shorter residence time of 30 min. It is concluded that feed rate of CO2 is dominant in precipitation experiments and it has a key role in dissociation and reaction of magnesium hydroxide in precipitation of magnesium carbonate.

Exit times for some processes with normally distributed noise

Denna avhandling handlar om metoder för att hitta begränsningar för det asymptotiska beteendet hos en förväntad uthoppstid från ett område omkring en xpunkt för processer som har normalfördelad störning. I huvudsak behandlas olika typer av autoregressiva processer. Fyra olika metoder används. En metod som använder principen för stora avvikelser samt en metod som jämför uthoppstiden med en återkomsttid ger övre begränsningar för den förväntade uthoppstiden. En martingalmetod och en metod för normalfördelade stokastiska variabler ger undre begränsningar. Metoderna har alla både förtjänster och nackdelar. Genom att kombinera de olika metoderna får man de bästa resultaten. Vi får fram gränsvärdet för det asymptotiska beteendet hos en uthoppstid för den multivariata autoregressiva processen, samt motsvarande gränsvärde för den univariata autoregressiva processen av ordning n.

The neural processes generating visual phenomenal consciousness: ERP and neuronavigated brain stimulation studies

One of the greatest conundrums to the contemporary science is the relation between consciousness and brain activity, and one of the specifi c questions is how neural activity can generate vivid subjective experiences. Studies focusing on visual consciousness have become essential in solving the empirical questions of consciousness. Th e main aim of this thesis is to clarify the relation between visual consciousness and the neural and electrophysiological processes of the brain. By applying electroencephalography and functional magnetic resonance image-guided transcranial magnetic stimulation (TMS), we investigated the links between conscious perception and attention, the temporal evolution of visual consciousness during stimulus processing, the causal roles of primary visual cortex (V1), visual area 2 (V2) and lateral occipital cortex (LO) in the generation of visual consciousness and also the methodological issues concerning the accuracy of targeting TMS to V1. Th e results showed that the fi rst eff ects of visual consciousness on electrophysiological responses (about 140 ms aft er the stimulus-onset) appeared earlier than the eff ects of selective attention, and also in the unattended condition, suggesting that visual consciousness and selective attention are two independent phenomena which have distinct underlying neural mechanisms. In addition, while it is well known that V1 is necessary for visual awareness, the results of the present thesis suggest that also the abutting visual area V2 is a prerequisite for conscious perception. In our studies, the activation in V2 was necessary for the conscious perception of change in contrast for a shorter period of time than in the case of more detailed conscious perception. We also found that TMS in LO suppressed the conscious perception of object shape when TMS was delivered in two distinct time windows, the latter corresponding with the timing of the ERPs related to the conscious perception of coherent object shape. Th e result supports the view that LO is crucial in conscious perception of object coherency and is likely to be directly involved in the generation of visual consciousness. Furthermore, we found that visual sensations, or phosphenes, elicited by the TMS of V1 were brighter than identically induced phosphenes arising from V2. Th ese fi ndings demonstrate that V1 contributes more to the generation of the sensation of brightness than does V2. Th e results also suggest that top-down activation from V2 to V1 is probably associated with phosphene generation. The results of the methodological study imply that when a commonly used landmark (2 cm above the inion) is used in targeting TMS to V1, the TMS-induced electric fi eld is likely to be highest in dorsal V2. When V1 was targeted according to the individual retinotopic data, the electric fi eld was highest in V1 only in half of the participants. Th is result suggests that if the objective is to study the role of V1 with TMS methodology, at least functional maps of V1 and V2 should be applied with computational model of the TMS-induced electric fi eld in V1 and V2. Finally, the results of this thesis imply that diff erent features of attention contribute diff erently to visual consciousness, and thus, the theoretical model which is built up of the relationship between visual consciousness and attention should acknowledge these diff erences. Future studies should also explore the possibility that visual consciousness consists of several processing stages, each of which have their distinct underlying neural mechanisms.

Planning and implementation of entrepreneurial marketing processes in SMEs

Entrepreneurial marketing is newly established term and there is need for more specific studies in order to understand the concept fully. SMEs have entrepreneurial marketing elements more visible in their marketing and therefore provide more fruitful insights for this research. SMEs marketing has gained more recognition during the past years and in some cases innovative characteristics can be identified despite constraints such as lack of certain resources. The purpose of this research is to study entrepreneurial marketing characteristics and SME processes in order to wider understanding and gain more insights of entrepreneurial marketing. In addition, planning and implementation of entrepreneurial marketing processes is examined in order to gain full coverage of SMEs marketing activities. The research was conducted as a qualitative research and data gathering was based on semi-structured interview survey, which involved nine company interviews. Multiple case research was used to analyze data so that focus and clarity could be maintained in organized manner. Case companies were chosen from different business fields so that more variation and insights could be identified. The empirical results suggest that two examined processes networking and word-of-mouth communication are very important processes for case companies which supports the previous researches. However, the entrepreneurial marketing characteristics had variation some were more visible and recognizable than others. Examining more closely the processes companies did not fully understand that networking or word-of-mouth marketing could be used as efficiently as other conventional marketing methods.

Advanced analysis and design methods for preparative chromatographic separation processes

Preparative liquid chromatography is one of the most selective separation techniques in the fine chemical, pharmaceutical, and food industries. Several process concepts have been developed and applied for improving the performance of classical batch chromatography. The most powerful approaches include various single-column recycling schemes, counter-current and cross-current multi-column setups, and hybrid processes where chromatography is coupled with other unit operations such as crystallization, chemical reactor, and/or solvent removal unit. To fully utilize the potential of stand-alone and integrated chromatographic processes, efficient methods for selecting the best process alternative as well as optimal operating conditions are needed. In this thesis, a unified method is developed for analysis and design of the following singlecolumn fixed bed processes and corresponding cross-current schemes: (1) batch chromatography, (2) batch chromatography with an integrated solvent removal unit, (3) mixed-recycle steady state recycling chromatography (SSR), and (4) mixed-recycle steady state recycling chromatography with solvent removal from fresh feed, recycle fraction, or column feed (SSR–SR). The method is based on the equilibrium theory of chromatography with an assumption of negligible mass transfer resistance and axial dispersion. The design criteria are given in general, dimensionless form that is formally analogous to that applied widely in the so called triangle theory of counter-current multi-column chromatography. Analytical design equations are derived for binary systems that follow competitive Langmuir adsorption isotherm model. For this purpose, the existing analytic solution of the ideal model of chromatography for binary Langmuir mixtures is completed by deriving missing explicit equations for the height and location of the pure first component shock in the case of a small feed pulse. It is thus shown that the entire chromatographic cycle at the column outlet can be expressed in closed-form. The developed design method allows predicting the feasible range of operating parameters that lead to desired product purities. It can be applied for the calculation of first estimates of optimal operating conditions, the analysis of process robustness, and the early-stage evaluation of different process alternatives. The design method is utilized to analyse the possibility to enhance the performance of conventional SSR chromatography by integrating it with a solvent removal unit. It is shown that the amount of fresh feed processed during a chromatographic cycle and thus the productivity of SSR process can be improved by removing solvent. The maximum solvent removal capacity depends on the location of the solvent removal unit and the physical solvent removal constraints, such as solubility, viscosity, and/or osmotic pressure limits. Usually, the most flexible option is to remove solvent from the column feed. Applicability of the equilibrium design for real, non-ideal separation problems is evaluated by means of numerical simulations. Due to assumption of infinite column efficiency, the developed design method is most applicable for high performance systems where thermodynamic effects are predominant, while significant deviations are observed under highly non-ideal conditions. The findings based on the equilibrium theory are applied to develop a shortcut approach for the design of chromatographic separation processes under strongly non-ideal conditions with significant dispersive effects. The method is based on a simple procedure applied to a single conventional chromatogram. Applicability of the approach for the design of batch and counter-current simulated moving bed processes is evaluated with case studies. It is shown that the shortcut approach works the better the higher the column efficiency and the lower the purity constraints are.

Fluvio-morphological processes of meander bends - Combining conventional field measurements, close-range remote sensing and computational modelling

Meandering rivers have been perceived to evolve rather similarly around the world independently of the location or size of the river. Despite the many consistent processes and characteristics they have also been noted to show complex and unique sets of fluviomorphological processes in which local factors play important role. These complex interactions of flow and morphology affect notably the development of the river. Comprehensive and fundamental field, flume and theoretically based studies of fluviomorphological processes in meandering rivers have been carried out especially during the latter part of the 20th century. However, as these studies have been carried out with traditional field measurements techniques their spatial and temporal resolution is not competitive to the level achievable today. The hypothesis of this study is that, by exploiting e increased spatial and temporal resolution of the data, achieved by combining conventional field measurements with a range of modern technologies, will provide new insights to the spatial patterns of the flow-sediment interaction in meandering streams, which have perceived to show notable variation in space and time. This thesis shows how the modern technologies can be combined to derive very high spatial and temporal resolution data on fluvio-morphological processes over meander bends. The flow structure over the bends is recorded in situ using acoustic Doppler current profiler (ADCP) and the spatial and temporal resolution of the flow data is enhanced using 2D and 3D CFD over various meander bends. The CFD are also exploited to simulate sediment transport. Multi-temporal terrestrial laser scanning (TLS), mobile laser scanning (MLS) and echo sounding data are used to measure the flow-based changes and formations over meander bends and to build the computational models. The spatial patterns of erosion and deposition over meander bends are analysed relative to the measured and modelled flow field and sediment transport. The results are compared with the classic theories of the processes in meander bends. Mainly, the results of this study follow well the existing theories and results of previous studies. However, some new insights regarding to the spatial and temporal patterns of the flow-sediment interaction in a natural sand-bed meander bend are provided. The results of this study show the advantages of the rapid and detailed measurements techniques and the achieved spatial and temporal resolution provided by CFD, unachievable with field measurements. The thesis also discusses the limitations which remain in the measurement and modelling methods and in understanding of fluvial geomorphology of meander bends. Further, the hydro- and morphodynamic models’ sensitivity to user-defined parameters is tested, and the modelling results are assessed against detailed field measurement. The study is implemented in the meandering sub-Arctic Pulmanki River in Finland. The river is unregulated and sand-bed and major morphological changes occur annually on the meander point bars, which are inundated only during the snow-melt-induced spring floods. The outcome of this study applies to sandbed meandering rivers in regions where normally one significant flood event occurs annually, such as Arctic areas with snow-melt induced spring floods, and where the point bars of the meander bends are inundated only during the flood events.

Toward including the effect of manufacturing processes in the pre-estimated losses of the switched reluctance motor

The estimation of losses plays a key role in the process of building any electrical machine. How to estimate those losses while designing any machine; by obtaining the characteristic of the electrical steel from the catalogue and calculate the losses. However, this way is inaccurate since the electrical steel performs several manufacturing processes during the process of building any machine, which affects directly the magnetic property of the electrical steel and accordingly the characteristic of the electrical steel will be affected. That means the B–H curve of the steel that was obtained from the catalogue will be changed. Moreover, during loading and rotating the machine, some important changes occur to the B–H characteristic of the electrical steel such as the stress on the laminated iron. Accordingly, the pre-estimated losses are completely far from the actual losses because they were estimated based on the data of the electrical steel obtained from the catalogue. So in order to estimate the losses precisely significant factors of the manufacturing processes must be included. The paper introduces the systematic estimation of the losses including the effect of one of the manufacturing factors. Similarly, any other manufacturing factor can be included in the pre-designed losses estimations.