Three-dimensional nonlinear inelastic analysis of steel moment-frame buildings damaged by earthquake excitations

The Northridge earthquake of January 17, 1994, highlighted the two previously known problems of premature fracturing of connections and the damaging capabilities of near-source ground motion pulses. Large ground motions had not been experienced in a city with tall steel moment-frame buildings before. Some steel buildings exhibited fracture of welded connections or other types of structural degradation.

A sophisticated three-dimensional nonlinear inelastic program is developed that can accurately model many nonlinear properties commonly ignored or approximated in other programs. The program can assess and predict severely inelastic response of steel buildings due to strong ground motions, including collapse.

Three-dimensional fiber and segment discretization of elements is presented in this work. This element and its two-dimensional counterpart are capable of modeling various geometric and material nonlinearities such as moment amplification, spread of plasticity and connection fracture. In addition to introducing a three-dimensional element discretization, this work presents three-dimensional constraints that limit the number of equations required to solve various three-dimensional problems consisting of intersecting planar frames.

Two buildings damaged in the Northridge earthquake are investigated to verify the ability of the program to match the level of response and the extent and location of damage measured. The program is used to predict response of larger near-source ground motions using the properties determined from the matched response.

A third building is studied to assess three-dimensional effects on a realistic irregular building in the inelastic range of response considering earthquake directivity. Damage levels are observed to be significantly affected by directivity and torsional response.

Several strong recorded ground motions clearly exceed code-based levels. Properly designed buildings can have drifts exceeding code specified levels due to these ground motions. The strongest ground motions caused collapse if fracture was included in the model. Near-source ground displacement pulses can cause columns to yield prior to weaker-designed beams. Damage in tall buildings correlates better with peak-to-peak displacements than with peak-to-peak accelerations.

Dynamic response of tall buildings shows that higher mode response can cause more damage than first mode response. Leaking of energy between modes in conjunction with damage can cause torsional behavior that is not anticipated.

Various response parameters are used for all three buildings to determine what correlations can be made for inelastic building response. Damage levels can be dramatically different based on the inelastic model used. Damage does not correlate well with several common response parameters.

Realistic modeling of material properties and structural behavior is of great value for understanding the performance of tall buildings due to earthquake excitations.

Digested sludge: delineation and modeling for ocean disposal

Experimental work was performed to delineate the system of digested sludge particles and associated trace metals and also to measure the interactions of sludge with seawater. Particle-size and particle number distributions were measured with a Coulter Counter. Number counts in excess of 10¹² particles per liter were found in both the City of Los Angeles Hyperion mesophilic digested sludge and the Los Angeles County Sanitation Districts (LACSD) digested primary sludge. More than 90 percent of the particles had diameters less than 10 microns.

Total and dissolved trace metals (Ag, Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn) were measured in LACSD sludge. Manganese was the only metal whose dissolved fraction exceeded one percent of the total metal. Sedimentation experiments for several dilutions of LACSD sludge in seawater showed that the sedimentation velocities of the sludge particles decreased as the dilution factor increased. A tenfold increase in dilution shifted the sedimentation velocity distribution by an order of magnitude. Chromium, Cu, Fe, Ni, Pb, and Zn were also followed during sedimentation. To a first approximation these metals behaved like the particles.

Solids and selected trace metals (Cr, Cu, Fe, Ni, Pb, and Zn) were monitored in oxic mixtures of both Hyperion and LACSD sludges for periods of 10 to 28 days. Less than 10 percent of the filterable solids dissolved or were oxidized. Only Ni was mobilized away from the particles. The majority of the mobilization was complete in less than one day.

The experimental data of this work were combined with oceanographic, biological, and geochemical information to propose and model the discharge of digested sludge to the San Pedro and Santa Monica Basins. A hydraulic computer simulation for a round buoyant jet in a density stratified medium showed that discharges of sludge effluent mixture at depths of 730 m would rise no more than 120 m. Initial jet mixing provided dilution estimates of 450 to 2600. Sedimentation analyses indicated that the solids would reach the sediments within 10 km of the point discharge.

Mass balances on the oxidizable chemical constituents in sludge indicated that the nearly anoxic waters of the basins would become wholly anoxic as a result of proposed discharges. From chemical-equilibrium computer modeling of the sludge digester and dilutions of sludge in anoxic seawater, it was predicted that the chemistry of all trace metals except Cr and Mn will be controlled by the precipitation of metal sulfide solids. This metal speciation held for dilutions up to 3000.

The net environmental impacts of this scheme should be salutary. The trace metals in the sludge should be immobilized in the anaerobic bottom sediments of the basins. Apparently no lifeforms higher than bacteria are there to be disrupted. The proposed deep-water discharges would remove the need for potentially expensive and energy-intensive land disposal alternatives and would end the discharge to the highly productive water near the ocean surface.

The aquatic biota of the now extinct lacustrine complex of the Mexico basin

The commonest organisms of the original Mexico lake complex are listed, including those that exist today in the Lago Viejo. In addition, a brief hydraulic history of this endorheic basin is given.

Remoção de metais pesados de efluentes sintéticos aquosos por nanofiltração

O objetivo deste trabalho foi estudar a remoção de metais pesados de efluentes sintéticos aquosos através de nanofiltração, com utilização de membrana de poliamida. A membrana utilizada constituída de poliamida apresentou uma boa permeabilidade hidráulica, constatada pela linearidade de fluxo com a variação de pressão de trabalho. Os metais estudados foram cobre, cádmio, zinco, chumbo e níquel com especiação de nitrato e sulfato. O desempenho do sistema foi verificado pela variação dos parâmetros operacionais (pressão e fluxo), associados também com a variação da salinidade e da concentração do metal. Em uma etapa inicial estudou-se a remoção de metais (nitrato e sulfato) isoladamente em uma mesma concentração molar, na pressão de 10 bar, comparando-se as rejeições com e sem agente complexante (EDTA). Em uma segunda etapa, estudou-se o desempenho da membrana, com misturas dos metais (nitrato) e mistura de metais (sulfato), também com e sem agente complexante, os resultados mostraram que a presença de agente complexante melhorou a rejeição dos metais. Nestas misturas estudaram-se os efeitos das concentrações (0,001; 0,0005 e 0,0001mol/L) e das pressões (5; 7; 10 e 12,5 bar) no sistema de remoção, constatou-se que o aumento da concentração e diminuição da pressão afeta a remoção. Em uma terceira etapa, estudou-se a influência da salinidade pela mistura de dois metais de mesma especiação (sulfato), comparando a remoção na pressão de 10 bar. Os resultados atestaram uma rejeição maior que 94 % para todos metais, na pressão de 10 bar, indicando um excelente desempenho e fluxo adequado, daí viabilidade de processo para todas as concentrações testadas. A pertinência do teste se justifica pela adequação do permeado ao atendimento aos padrões ambientais de concentração de metais e confirmam a eficácia do sistema de nanofiltração na remoção de metais pesados

Comparative limnology of waters in a coniferous forest: is a generalisation possible?

The high density of meres and mosses in the Delamere area comes from numerous moraine-hollows formed after the melting of stranded ice-blocks following last glaciation. The main vegetation is of conifers along with some deciduous species and the area was designated as a National Forest Park in 1987. It has been managed since the beginning of the 19th century and is a popular tourist area with walking, orienteering, cycling and educational activities. In recent years this forest park has been attracting over half a million people per year. This paper studies the limnology of different aquatic habitats in the Delamere Forest area in order to give some insight into the waters of a coniferous, temperate forest area, which has so far been largely unexplored. The authors assume therefore, thought that despite apparent large variability in origin, age, surface area, morphometry, catchment size and hydraulic regime, the waters of Delamere Forest might share some revealing chemical and biological features. Seven water-bodies in the Delamere Forest Park area, namely, Black Lake, Blakemere Moss, Delamere Lake, Delamere Quarry, Hatchmere, Windyhowe Farm Spring and Fir Brook were sampled, their water chemistry and dissolved organic carbon and the occurrence of phytoplankton and zooplankton species examined. In a final chapter the authors analyse their findings for patterns.

Scalable Methods for Deterministic Integration of Quantum Emitters in Photonic Crystal Cavities

We investigated four unique methods for achieving scalable, deterministic integration of quantum emitters into ultra-high Q{V photonic crystal cavities, including selective area heteroepitaxy, engineered photoemission from silicon nanostructures, wafer bonding and dimensional reduction of III-V quantum wells, and cavity-enhanced optical trapping. In these areas, we were able to demonstrate site-selective heteroepitaxy, size-tunable photoluminescence from silicon nanostructures, Purcell modification of QW emission spectra, and limits of cavity-enhanced optical trapping designs which exceed any reports in the literature and suggest the feasibility of capturing- and detecting nanostructures with dimensions below 10 nm. In addition to process scalability and the requirement for achieving accurate spectral- and spatial overlap between the emitter and cavity, these techniques paid specific attention to the ability to separate the cavity and emitter material systems in order to allow optimal selection of these independently, and eventually enable monolithic integration with other photonic and electronic circuitry.

We also developed an analytic photonic crystal design process yielding optimized cavity tapers with minimal computational effort, and reported on a general cavity modification which exhibits improved fabrication tolerance by relying exclusively on positional- rather than dimensional tapering. We compared several experimental coupling techniques for device characterization. Significant efforts were devoted to optimizing cavity fabrication, including the use of atomic layer deposition to improve surface quality, exploration into factors affecting the design fracturing, and automated analysis of SEM images. Using optimized fabrication procedures, we experimentally demonstrated 1D photonic crystal nanobeam cavities exhibiting the highest Q/V reported on substrate. Finally, we analyzed the bistable behavior of the devices to quantify the nonlinear optical response of our cavities.

Avaliação da remoção de níquel em solução aquosa pelo processo de osmose inversa

O objetivo deste trabalho foi investigar o desempenho de uma membrana comercial na remoção de um metal pesado (níquel) de efluentes sintéticos, por osmose inversa. Na primeira etapa foi realizada uma comparação com os resultados obtidos com soluções de alimentação contendo sais, como NaCl, NaNO3 e Ni(NO3)2.6 H2O, nas concentrações de 50, 100 e 200 ppm, e nas pressões de 10, 20 e 26 bar. Os resultados mostraram que a influência da concentração e da pressão aplicada ao sistema não afetaram as rejeições de forma significativa. Na segunda etapa, como os parâmetros não influíram significativamente na rejeição dos sais, optou-se, pela aplicação de uma pressão de operação de 10 bar, para avaliar a eficiência de remoção de níquel. A membrana utilizada, constituída de poliamida, modelo HR98PP e fornecida pela DOW/Filmtec, apresentou uma boa permeabilidade hidráulica. Os resultados mostraram que para todas as concentrações testadas, as rejeições de níquel ultrapassaram 96%, comprovando a boa seletividade deste tipo de membrana na rejeição do referido metal, com fluxos de permeado variando entre 4,78 e 5,55 L/h.m2 , sob pressão de operação de 10 bar. Para estudar o efeito do tamanho iônico na rejeição da membrana, o níquel foi complexado pela adição de um agente quelante na solução de alimentação. O agente escolhido foi o Na2EDTA, devido à formação de um complexo estável com o níquel e por ser um agente não prejudicial à saúde humana. Os resultados com adição de EDTA indicaram um aumento na rejeição de níquel, atingindo o índice máximo de 98,22 %, partindo-se de uma solução com 40,39 ppm de Ni2+, e confirmam que o processo de osmose inversa com a membrana HR98PP é altamente adequado para o tratamento de efluentes contendo níquel

The extent of the rearrangement of material in Neuwerk/Scharhom flat [Translation from: Hamburger Kuestenforschung 33, 1-24 [p23 only], 1975]

Investigations of the rearrangement of material in Neuwerk/Scharhom flat showed that with the exception of the western border/edge and the parts of the Elbe and Oste shores/banks which lie most seawards, the entire mudflat area is only infrequently exposed to strong hydraulic forces. Only in extreme conditions, which on average occur rarely more than once a year, would the mudflats be severely affected. This partial translation provides the summary of the original article only.

Longitudinal dispersion in laboratory and natural streams

This study concerns the longitudinal dispersion of fluid particles which are initially distributed uninformly over one cross section of a uniform, steady, turbulent open channel flow. The primary focus is on developing a method to predict the rate of dispersion in a natural stream.

Taylor's method of determining a dispersion coefficient, previously applied to flow in pipes and two-dimensional open channels, is extended to a class of three-dimensional flows which have large width-to-depth ratios, and in which the velocity varies continuously with lateral cross-sectional position. Most natural streams are included. The dispersion coefficient for a natural stream may be predicted from measurements of the channel cross-sectional geometry, the cross-sectional distribution of velocity, and the overall channel shear velocity. Tracer experiments are not required.

Large values of the dimensionless dispersion coefficient D/rU* are explained by lateral variations in downstream velocity. In effect, the characteristic length of the cross section is shown to be proportional to the width, rather than the hydraulic radius. The dimensionless dispersion coefficient depends approximately on the square of the width to depth ratio.

A numerical program is given which is capable of generating the entire dispersion pattern downstream from an instantaneous point or plane source of pollutant. The program is verified by the theory for two-dimensional flow, and gives results in good agreement with laboratory and field experiments.

Both laboratory and field experiments are described. Twenty-one laboratory experiments were conducted: thirteen in two-dimensional flows, over both smooth and roughened bottoms; and eight in three-dimensional flows, formed by adding extreme side roughness to produce lateral velocity variations. Four field experiments were conducted in the Green-Duwamish River, Washington.

Both laboratory and flume experiments prove that in three-dimensional flow the dominant mechanism for dispersion is lateral velocity variation. For instance, in one laboratory experiment the dimensionless dispersion coefficient D/rU* (where r is the hydraulic radius and U* the shear velocity) was increased by a factory of ten by roughening the channel banks. In three-dimensional laboratory flow, D/rU* varied from 190 to 640, a typical range for natural streams. For each experiment, the measured dispersion coefficient agreed with that predicted by the extension of Taylor's analysis within a maximum error of 15%. For the Green-Duwamish River, the average experimentally measured dispersion coefficient was within 5% of the prediction.

Ecology and management of water plants in lowland streams

A review article which discusses the ecology and management of common water plants in lowland streams, with an introduction containing a review of previous studies on the subject. The article covers the significance of seasonal growth, the significance of stand structure (particularly in relation to hydraulic resistence), an assessment of current river management, improvements to plant management techniques (in relation to cutting), and alternatives to the traditional techniques of river plant management. There are a number of accompanying figures.

The Maryland soft shell clam industry and its effects on Tidewater resources

This report to the Maryland General Assembly covers: design and operation of the hydraulic clam dredge; summary of knowledge of Maryland's soft shell clam resource; development and present status; Potential value of the resource; Effects of the hydraulic clam dredge; evaluation of the effects of certain proposals concerning the soft shell clam industry; summary.

Diseño hidráulico para la red de abastecimiento de agua en el cantón de Conacaste, municipio de Comasagua, El Salvador.

[ES]El presente trabajo tiene como objetivo el diseño hidráulico de un sistema de abastecimiento de agua potable para las comunidades de La Violeta-Arcoiris, La Ceiba, San Rafael, La Finquita y La Dalia en el municipio de Comasagua, El Salvador. Para ello, se utilizaran los datos recogidos en el Plan Director para el abastecimiento y saneamiento de agua en zonas rurales del sur de La Libertad y las mediciones llevadas a cabo en terreno. Atendiendo tanto a las especificaciones técnicas y los criterios de diseño de ACUA como a los cálculos hidráulicos realizados, se ha seleccionado la mejor alternativa a desarrollar.

Proyecto de un parque eólico para la alimentación de las bombas de la central hidráulica de Belesar (Lugo).

[ES]El proyecto consiste en el estudio de las necesidades energéticas de las bombas de una central hidráulica y la construcción de un parque eólico para satisfacer dichas necesidades. Para ello será necesario llevar a cabo un estudio del área y así encontrar el lugar más adecuado para ubicar los aerogeneradores, teniendo en cuenta la frecuencia, velocidad y dirección de los vientos predominantes del lugar. Después habrá que estudiar el mercado y elegir el aerogenerador adecuado para las condiciones del lugar y del viento, atendiendo también a otras cuestiones de relevancia. Se estudiará, además, la posibilidad de inyectar un posible exceso de electricidad a la red general. Una vez hecho esto, habrá que calcular el coste del proyecto.

Estudio de viabilidad de la central hidroeléctrica de Ubao –Toquillo.

[ES]El objetivo del presente proyecto de viabilidad es estudiar la eficiencia y productividad de la central hidroeléctrica de Ubao – Toquillo, situada en Oñati, Gipuzkoa (España), ofreciendo a su vez una serie de alternativas económica y técnicamente viables. Para ello, se analizarán los elementos de la central; aunque la turbina hidráulica sea el elemento fundamental de la central, se tendrán en cuenta otros elementos como, por ejemplo, estructuras mecánicas o máquinas eléctricas. Para cada una de las alternativas, se calculará la producción de energía y la inversión necesaria, y se compararán unas con otras. Finalmente, se seleccionará la óptima que pasará a desarrollarse en el anteproyecto.