Determination of the betaine content of feed ingredients using high-performance liquid chromatography

A series of studies was conducted to establish a methodology for the accurate and efficient determination of betaine in different feed ingredients. The final methodology involves an extraction step in which the feed sample is heated for 3h in a methanolic KOH solution using a Goldfisch apparatus. Impurities are removed by the addition of activated charcoal and concentrated (36%) HCl. After centrifugation the extractant is passed through a strong cation exchange resin (Dowex 50W-X12, H+). The betaine retained in the column is eluted with 1.5 N HCl. A 2 nil aliquot of the elute is air dried and reconstituted with 1 ml of deionised water. HPLC separation with a cation exchange column (Partisil SCX-10) is used for the separation of betaine from other compounds. The mobile phase is kept constant at 50mm KH2PO4 in water, and eluted compounds are detected by UV absorbance (200nm). The flow rate is maintained at 1.5ml min(-1). This assay is very accurate over the range of betaine concentrations from 15 to 650 mug ml(-1), with a lower detection limit in feeds of approximately 500 mug g(-1) when 4g of sample is extracted. Recovery assays done with standard betaine hydrochloride and hard red wheat resulted in a consistent recovery of 80%. Betaine content was quantified in several feed ingredients, including alfalfa (1.77 mg kg(-1)), wheat (3.96 mg kg(-1)), wheat middlings (4.98 mg kg(-1)) and poultry meal (0.77 mg kg(-1)). Betaine in corn and soybean meal was not detectable by this method, even when 16g of sample was used (<125 mg kg(-1)). Betaine present in several feed ingredients should influence choline supplementation to animal feeds and may have implications for human health. (C) 2002 Society of Chemical Industry.

A flow-injection-ICP system sequential multielemental analysis with simultaneously mercury(II) preconcentration step

A flow-injection system for multielemental analysis with a mercury(II) preconcentration step using a resin Chelite-S(R)(Serva Feinbiochemica Heidelberg, Part No. 41709) packed minicolumn by inductively coupled plasma atomic emission spectroscopy is described. A mercury reductive elution procedure with a mixture of SnCl2/HCl was used, which allows use of 6 mol/L HCl solution instead of concentrated hydrochoric acid. The main parameters related to ICP operation, such as radio frequency power (950-1750 W), auxiliary argon flow (0.0-1.5 L/min) and spray chamber nebulizer pressure (15-35 psi), were studied. Optimization of the FIA system was reached by defining the best eluent carrier stream (1.4-2.8 mL/min), Hgdegrees carrier stream (10-40 mL min(-1)), loading time (0.5-4.0 min), sample flow rate (1.25-10.0 mL/min), temperature of reactor gas liquid separator (GLS) (25-75 degreesC) and eluent volume (50-350 muL). Throughput is around 30 samples per hour for analytical solutions within the range 50-2500 ng Hg(II)/L. Results from certified material showed good precision (RSD < 3%, n = 12) and no statistical difference was observed for real samples analyzed by AAS and by the proposed system.

Allergenic extracts from Metarhizium anisopliae: Obtainment and characterization

Metarhizium anisopliae is used as a biopesticide for insects that damage agricultural plantations like sugar cane and forage plants. In a previous study the sensitization to this fungus of asthmatic patients coming from sugar cane areas was showed. The aims of this work were: to compare crude extracts obtained with Tris-HCl and Coca liquid from several growth phases of M. anisopliae concerning the total content of proteins and their electrophoretic analysis profile; to evaluate in vivo allergic sensitization in Balb/c mice and allergic patients from a sugar cane area, and to characterize the allergenic fractions in the sera of patients positive for the prick test by means of Western-blotting. The extract obtained with Coca liquid on the 16(th) day was the one that presented the greatest number of proteic fractions, including all those present in the other extracts. Twelve fractions were verified in this extract with approximate molecular weights from 94 to 14 kDa. The allergenicity of the extract obtained on the 16(th) day was proven by the production of IgE antibodies in Balb/c mice, with titres of 200. Prick tests carried out with the extract of the 16(th) day in 79 atopic individuals (from sugar cane area), 35 atopic individuals (from urban area) and 11 non- atopic individuals showed respective positivity of 29%, 9% and 0%. The allergenic characterization in vitro was performed by means of Western blotting, and the fractions that reacted with the positive individuals' sera were those of approximate molecular weights of 67 kDa (95%); 20 kDa (55%); 94 kDa (36%); 34 and 36 kDa (23%); 43 and 48 kDa (14%): 16 kDa (9%) and 54kDa (5%). It was concluded that the crude allergenic extract, obtained with Coca liquid from the 16(th) day growth of Metarhizium anisopliae, contains allergenic fractions and can be used in diagnostic screening tests.

Structural and physicochemical characteristics of lintnerized native and sour cassava starches

The comprehension of the structure of starch granules is important for the understanding of its physicochemical properties. Native and sour cassava starches after being analyzed with respect to their pasting properties and baking expansion capacity, were treated with 2.2 N HCl at 38 degreesC for a maximum of nine days. The starch granules remaining after lintnerization were analyzed for amylose content and intrinsic viscosity, by X-ray diffraction, scanning electron microscopy and chromatographic analysis. The results indicated that the acid hydrolysis on all starches occurred in two steps. The first one, with high hydrolysis rate, was characterized by a quick degradation of the amorphous part of the granules whereas the second step, with lower hydrolysis rate, was characterized by a higher resistance of the organized areas of the granules to acid treatment. Most of the amylose chains were found in the amorphous areas of starch granules only a small percentage was involved in the crystalline regions. The microscopic and chromatographic analysis demonstrated that the acid hydrolysis was not able to disrupt the entire granular crystalline structure. Fermented starch showed amylose and/or amylopectin chain fractions resistant to pullulanase, probably due to structural alterations during fermentation.

Sources of atmospheric acidity in an agricultural-industrial region of São Paulo State, Brazil

[1] Surface-based measurements of atmospheric formic acid (HCOOH), acetic acid (CH3COOH), sulfur dioxide (SO2), hydrogen chloride (HCl), and nitric acid (HNO3) were made in central São Paulo State, Brazil, between April 1999 and March 2000. Mean concentrations were 9.0 ppb (HCOOH), 1.3 ppb (CH3COOH), 4.9 ppb (SO2), 0.3 ppb (HCl), and 0.5 ppb (HNO3). Concentrations in sugar cane burning plumes were 1160-4230 ppb (HCOOH), 360-1750 ppb (CH3COOH), 10-630 ppb (SO2), 4-210 ppb (HCl), and 14-90 ppb (HNO3). Higher ambient concentrations of SO2, HCl and HNO3 were measured during the burning season (May-November). Concentrations of SO2 and HCl increased during the evening, and of HCOOH and CH3COOH were lowest in the morning, with peak levels in the afternoon. Ratios obtained between different species showed either nighttime maxima (SO2/HCOOH, SO2/CH3COOH, SO2/HNO3, CH3COOH/HNO3, SO2/HCl and HCOOH/HNO3), daytime maxima (HCOOH/HCl, CH3COOH/HCl and HNO3/HCl), or no clear trends (HCOOH/CH3COOH). Correlation analysis showed that SO2 and HCl were primary emissions from biomass burning and road transport; HCOOH, HNO3 and CH3COOH were products of photochemistry; HCOOH and CH3COOH were emitted directly during combustion as well as from biogenic sources. Biomass burning affected atmospheric acidity on a regional scale, while vehicular emissions had greater impact in urban and adjacent areas. Atmospheric ammonia levels were insufficient to neutralize atmospheric acidity, which was mainly removed by deposition to the surface.

Chromotropic acid-formaldehyde reaction in strongly acidic media. The role of dissolved oxygen and replacement of concentrated sulphuric acid

The procedure for formaldehyde analysis recommended by the National Institute for Occupational Safety and Health (NIOSH) is the Chromotropic acid spectrophotometric method, which is the one that uses concentrated sulphuric acid. In the present study the oxidation step associated with the aforementioned method for formaldehyde determination was investigated. Experimental evidence has been obtained indicating that when concentrated H2SO4 (18 mol l(-1)) is used (as in the NIOSH procedure) that acid is the oxidizing agent. on the other hand, oxidation through dissolved oxygen takes place when concentrated H2SO4 is replaced by concentrated hydrochloric (12 mol l(-1)) and phosphoric (14.7 mol l(-1)) acids as well as by diluted H2SO4 (9.4 mol l(-1)). Based on investigations concerning the oxidation step, a modified procedure was devised, in which the use of the potentially hazardous and corrosive concentrated H2SO4 was eliminated and advantageously replaced by a less harmful mixture of HCl and H2O2. (C) 2003 Elsevier B.V. B.V. All rights reserved.

Seleção de extratores químicos para avaliação da disponibilidade de zinco em solos do estado de São Paulo

The purpose of this study was to evaluate methods for predicting availability of Zn in soils. Surface soil samples representing Podzolized soils from Lins and Marilia var. Marilia and var. Lins, medium texture Dark-Red Latosol, Dusky-Red Latosol and Terra Roxa Estruturada, were gathered from fields in Jaboticabal, SP, Brazil. Com was used as indicator plant in a greenhouse experiment. Availability of Zn was determined with: 0.5 M CaCl2, 2.0 N MgCl2, N CH3COONH4 (pH 6.0 and 4.8), 0.05 and 0.1 N HCl, 0.05 N H2SO4, 0.005 M DTPA (pH 7.3 and 6.0), 1.0% Na2-EDTA, 0.01 M EDTA + 1.0 M (NH4)2CO3 (pH 8.6) and 0.02 M EDTA + 0.5 M CH3COOH + 0.5 M CH3COONH4. By using the simple correlation coefficients (Zn extracted from soils x absorbed by plants it can be concluded that the complexant agents and acid solutions showed to be efficient. The salt solutions showed low extraction capacity, low correlation coefficients and less accuracy. By considering aspects as accuracy and easy management DTPA pH 7,3 and Na2-EDTA can be indicated as the most apropriates (r values, respectively, 0.873** and 0.868** and V.C. 7.52% and 7.98%).

Label-free DNA detection based on modified conducting polypyrrole films at microelectrodes

A label-free electrochemical detection method for DNA hybridization based on electrostatic modulation of the ion-exchange kinetics of a polypyrrole film deposited at microelectrodes is reported. Synthetic single-stranded 27-mer oligonucleotides (probe) have been immobilized at 2,5-bis(2-thienyl)-N-(3-phosphorylpropyl)pyrrole film formed by electropolymerization on the previously formed polypyrrole layer. The 27- or 18-mer target oligonucleotides were monitored via the electrochemically driven anion exchange of the inner polypyrrole film. The performance of the miniaturized DNA biosensor system was studied in respect to selectivity, sensitivity, reproducibility, and regeneration of the sensor. Control experiments were performed with a noncomplementary target of 27-mer DNA and 12 base-pair mismatched 18-mer sequences, respectively, and did not show any unspecific binding. Under optimized experimental conditions, the label-free electrochemical biosensor enabled the detection limits of 0.16 and 3.5 fmol for the 18- and 2 7-mer DNA strand, respectively. Furthermore, we demonstrate reusability of the electrochemical DNA biosensor after successful recovery of up to 100% of the original signal by regenerating the DNA label-free electrode with 50 mM HCl at room temperature.

Thermal behaviour of Tin(II) complex with 8-hydroxyquinolinate in the solid state

Tin(II) complexes with 8-hydroxyquinolinate in solid state have been obtained by adding aqueous ammonium to a solution containing stannous chloride and 8-hydroxiquinoline in medium of HCl and acetone up to pH 5 and 9, respectively. The products obtained show the same composition, Sn(C9H6ON)(2); however there are some differences regarding both the thermal behaviour in an oxidant atmosphere and morphology. These products were characterised by elemental and complexometric analysis, TG and DTA curves, infrared and X-ray diffractometry. TG curves show, above 448 K, the partial oxidation on air atmosphere of Sn(II) complexes to Sn(IV) complexes, SnO(C9H6ON)(2). This behaviour does not depend only on pH in which the compounds were obtained but also on the heating rate in TG curves. Sn(II) complexes volatilise almost completely on nitrogen atmosphere and partially on air atmosphere depending on the oxidation degree of the compound.

Voltammetric assay of albendazole in pharmaceutical dosage forms

A simple, rapid inexpensive voltammetric method have been developed for the quantitative determination of albendazole (ABZ) as the pure assay, by direct dissolution of commercial tablets in HCl solutions. Studies with linear sweep (LSV), square-wave (SWV) and differential pulse voltammetry (DPV) were carried out ABZ in aqueous medium at a glassy carbon electrode. A well defined irreversible oxidation peak current was obtained at 1,00V vs. SCE. The method permits a precise quantitative determination of ABZ using the standard addition method. The detection limits for the three voltammetric techniques were found to be 3.0 x 10(-5) M (LSV), 6.2 x 10(-5) M (SWV) and 4.0 x 10(-5) M (DPV).

Effect of natural rubber latex on the conducting state of polyaniline blends determined by Raman spectroscopy

Blends possessing the elastomeric properties of natural rubber (NR) and the conducting properties of conducting polymer (polyaniline, PANI) were obtained, which are promising for further application in deformation sensors. Blends containing 20% (v/v) of PANI in 80% of NR latex were fabricated by casting in the form of free-standing films and treated either with HCl or with corona discharge, which lead PANI to its conducting state (doping process). Characterization was carried out by Raman spectroscopy, d.c. conductivity and thermogravimetric analysis. Evidence for chemical interaction between PANI and NR was observed, which allowed the conclusion that the NR latex itself is able partially to induce both the primary doping of PANI (by protonation) and the secondary doping of PANI (by changing the chain conformation). Further improvement in the primary doping could be obtained for the blends either by corona discharge or by exposing them to HCl the electrical conductivity reached in the blends was dependent on the doping conditions used, as observed by Raman scattering. Copyright (C) 2003 John Wiley Sons, Ltd.

Identification, content, and distribution of type VI collagen in bovine tendons

Tendon composition changes according to differentiation, mechanical load, and aging. In this study, we attempted to identify, localize, and quantify type VI collagen in bovine tendons. Type VI collagen was identified by the electrophoretic behavior of the alpha chains and Western blotting, and by rotary shadowing. Type VI collagen was extracted from powdered tendon with three sequential 24-h extractions with 4 M guanidine-HCl. The amount of type VI collagen was determined by enzyme-linked immunosorbent assay for purely tensional areas and for the compressive fibrocartilage regions of the deep flexor tendon of the digits, for the corresponding fetal and calf tendons, and for the extensor digital tendon. The distal fibrocartilaginous region of the adult tendon was richer in type VI collagen than the tensional area, reaching as much as 3.3 mg/g (0.33%) of the wet weight. Calf tendons showed an accumulation of type VI at the fibrocartilage site. Immunocytochemistry demonstrated that type VI collagen was evenly distributed in the tensional areas of tendons but was highly concentrated around the fibrochondrocytes in the fibrocartilages. The results demonstrate that tendons are variable with regard to the presence and distribution of type VI collagen. The early accumulation of type VI collagen in the region of calf tendon that will become fibrocartilage in the adult suggests that it is a good marker of fibrocartilage differentiation. Furthermore, the distribution of type VI collagen in tendon fibrocartilage indicates that it organizes the pericellular environment and may represent a survival factor for these cells.

Determination of soybean seed respiration rate by the titulation method

This trial was carried out under laboratory conditions, with three lots of Iguacu soybean seeds, to determine the respiration rate by the titulation method. A randomized complete block design was used, with four repetitions, each one of them with 50 seeds and a control without seeds for each lot. The seeds were placed in gerbox with 40 mi of KOH 0.1N, on distilled water wet blotting paper for fixing the CO2 produced by seeds respiration. The material was placed in germinator at constant 25 degrees C for 16, 24 and 48 hours. After these periods, the titulation of the fixative solution was performed with HCl 0.1N to check the respiration rate. The most deteriorated seeds were those that presented the highest respiration rates, which were measured in mg of CO2/g of dry matter, when compared with the most vigorous lots. The titulation method was suitable for the evaluation of soybean seed respiration rate because the final results separated the lots in three different quality levels that were compatible with the results obtained from the accelerated aging and emergence.

A CALORIMETRIC STUDY OF THE ULTRASOUND-STIMULATED HYDROLYSIS OF SOLVENTLESS TEOS-WATER MIXTURES

The kinetics of ultrasound-stimulated and HCl-catalyzed hydrolysis of solventless TEOS-water mixtures was studied as a function of temperature ranging from 10 degrees C up to 65 degrees C by means of flux calorimetry measurements. A specially designed device was utilized for this purpose. The exothermic peak arising few minutes after sonication began has been attributed mainly to the hydrolysis reaction. The overall hydrolysis process, which was measured through the irradiation time up to the hydrolysis peak, was found to be thermally activated, with an apparent activation energy Delta E = 36.4 kJ/mol. The alcohol produced at the early hydrolysis due to sonication seems to further enhance the reaction, via a parallel autocatalytic path, which is controlled by a faster pseudo second order rate constant (k'). Our modeling yielded k' = 6.3 x 10(-2) M(-1) min(-1) at 20 degrees C, which is in a reasonable agreement with the literature, and an activation energy Delta E = 40.4 kJ/mol for the specific process of hydrolysis in presence of alcohol.

Diagnosis and environmental planning for Paranagud - PR - Brazil

The main goal of this study was to identify and analyse environmental problems related to human occupation at the south part of the city of Paranagua PR, Brazil, aiming the diagnosis and conceptual evaluation of landscape use. For landscape use assessments and degradation diagnosis purposes, the environment was classified considering mainly geological and geomorphologic characteristics, such as declivity and sediment origin. The identification of potential environmental impacts was made by aerial photographs, Landsat-TM images, photographic records, surface sediment samples, water-column samples, and mainly observation visits to each classified unit. Surface sediment samples were taken with a Petit-Ponar sampler, in 13 station located in Paranagua Bay. In order to characterize the contamination level on sediments, the concentration of the following elements were analysed: arsenic (As), copper (Cu), cadmium (Cd), nickel (Ni), lead (Ph) e zinc (Zn). For the extraction of these elements, samples were treated with HCl 0.1N for 12 hours. This method has the advantage of determining contaminants which are weakly bind to the sediment, thus more available to the system. Analysis were performed by atomic absorption spectroscopy. According to the adopted criteria, sectors were classified as hills, mangroves, continental sediments and beach ridges urban and port industrial. Water quality and concentrations of metallic elements were determined at three sectors one control and two with the influence of urban and port/industrial activities, respectively the major upland impacts found were: deforestation due to disordered occupation, and solid waste emission through domestic and industrial sewage. The diagnosis of the actual situation was used as a basis for a management plan, once it allows the identification of impacts, and consequent environmental irregularities. Based on this considerations, suggestions for land use and management were presented, which offers a better approach for recuperation and protection of the studied ecosystem.