Studies on the target conditioning for deposition of $LiCoO_{2}$ films

Deposition of good quality thin films of Lithium Cobalt Oxide (LiCoO2), by sputtering is preceded by target conditioning, which dictates the surface composition, morphology and electrochemical performance of the deposited film. Sputtering from a Virgin target surface, results in films with excess of the more reactive elements. The concentration of these reactive elements in the films decreases until the system reaches a steady state after sufficient sputtering from the target. This paper discusses the deposition kinetics in terms of target conditioning of LiCoO2. The composition, morphology and texturing of deposited film during various hours of sputtering were analyzed using X-ray photoelectron Spectroscopy (XPS) and Field Emission Scanning electron microscopy (FESEM). The compositional stability is not observed in the films formed during the initial hours or Sputtering from the fresh target, which becomes stable after several hours of sputtering. The Li and Co concentration in the Films deposited subsequently is found to be varying and possible causes are discussed. After the compositional stability is reached, electrochemical analysis of LiCoO2 thin films was performed, which shows a discharge capacity of 129 mu Ah/cm(2).

Long range resonance energy transfer from a dye molecule to graphene has (distance)-4 dependence

In our previous report on resonance energy transfer from a dye molecule to graphene [J. Chem. Phys.129, 054703 (2008)], we had derived an expression for the rate of energy transfer from a dye to graphene. An integral in the expression for the rate was evaluated approximately. We found a Yuwaka-type dependence of the rate on the distance. We now present an exact evaluation of the integral involved, leading to very interesting results. For short distances (z < 20 A), the present rate and the previous rate are in good agreement. For larger distances, the rate is found to have a z(-4) dependence on the distance, exactly. Thus we predict that for the case of pyrene on graphene, it is possible to observe fluorescence quenching up to a distance of 300 A. This is in sharp contrast to the traditional fluorescence resonance energy transfer where the quenching is observable only up to 100 A.

Electrochemical phase formation (ECPF): Nucleation growth vis-a-vis adsorption models

The nucleataon growth model of electrochemical phase formation is analysed for the hnear potential sweep input Apart from deducing diagnostic criteria and method~ of estimating model parameters, the predictions of the nucleation growth model are compared and contrasted with those of a sample adsorption model A dastlnCtlOn is made possible between adsorption and phase transition, which seems useful for understanding the nature of ECPF phenomena, especially underpotentlal deposition (UPD).

Some aspects of multilevel load-frequency control of a power system

The application of multilevel control strategies for load-frequency control of interconnected power systems is assuming importance. A large multiarea power system may be viewed as an interconnection of several lower-order subsystems, with possible change of interconnection pattern during operation. The solution of the control problem involves the design of a set of local optimal controllers for the individual areas, in a completely decentralised environment, plus a global controller to provide the corrective signal to account for interconnection effects. A global controller, based on the least-square-error principle suggested by Siljak and Sundareshan, has been applied for the LFC problem. A more recent work utilises certain possible beneficial aspects of interconnection to permit more desirable system performances. The paper reports the application of the latter strategy to LFC of a two-area power system. The power-system model studied includes the effects of excitation system and governor controls. A comparison of the two strategies is also made.

Preliminary investigations into the use of a functionalised polymer to reduce diffusion in Fricke gel dosimeters

Purpose A modification of the existing PVA-​FX hydrogel has been made to investigate the use of a functionalised polymer in a Fricke gel dosimetry system to decrease Fe3+ diffusion. Methods The chelating agent, xylenol orange, was chem. bonded to the gelling agent, polyvinyl alc. (PVA) to create xylenol orange functionalised PVA (XO-​PVA)​. A gel was created from the XO-​PVA (20​% w​/v) with ferrous sulfate (0.4 mM) and sulfuric acid (50 mM)​. Results This resulted in an optical d. dose sensitivity of 0.014 Gy-​1, an auto-​oxidn. rate of 0.0005 h-​1, and a diffusion rate of 0.129 mm2 h-​1; an 8​% redn. compared to the original PVA-​FX gel, which in practical terms adds approx. 1 h to the time span between irradn. and accurate read-​out. Conclusions Because this initial method of chem. bonding xylenol orange to polyvinyl alc. has inherently low conversion, the improvement on existing gel systems is minimal when compared to the drawbacks. More efficient methods of functionalising polyvinyl alc. with xylenol orange must be developed for this system to gain clin. relevance.

A Sketch of the Phonology and Grammar of Rajbanshi

This dissertation is a synchronic description of the phonology and grammar of two dialects of the Rajbanshi language (Eastern Indo-Aryan) as spoken in Jhapa, Nepal. I have primarily confined the analysis to the oral expression, since the emerging literary form is still in its infancy. The grammatical analysis is therefore based, for the most part, on a corpus of oral narrative text which was recorded and transcribed from three informants from north-east Jhapa. An informant, speaking a dialect from south-west Jhapa cross checked this text corpus and provided additional elicited material. I have described the phonology, morphology and syntax of the language, and also one aspect of its discourse structure. For the most part the phonology follows the basic Indo-Aryan pattern. Derivational morphology, compounding, reduplication, echo formation and onomatopoeic constructions are considered, as well as number, noun classes (their assignment and grammatical function), pronouns, and case and postpositions. In verbal morphology I cover causative stems, the copula, primary and secondary agreement, tense, aspect, mood, auxiliary constructions and non-finite forms. The term secondary agreement here refers to genitive agreement, dative-subject agreement and patient (and sometimes patient-agent) agreement. The breaking of default agreement rules has a range of pragmatic inferences. I argue that a distinction, based on formal, semantic and statistical grounds, should be made between conjunct verbs, derivational compound verbs and quasi-aspectual compound verbs. Rajbanshi has an open set of adjectives, and it additionally makes use of a restricted set of nouns which can function as adjectives. Various particles, and the emphatic and conjunctive clitics are also considered. The syntactic structures studied include: non-declarative speech acts, phrase-internal and clause-internal constituent order, negation, subordination, coordination and valence adjustment. I explain how the future, present and past tenses in Rajbanshi oral narratives do not seem to maintain a time reference, but rather to indicate a distinction between background and foreground information. I call this tense neutralisation .

Suomen rautakautiset kulkuset, kellot ja kelloriipukset : äänimaiseman arkeologiaa

The thesis addresses the problem of Finnish Iron Age bells, pellet bells and bell pendants, previously unexplored musical artefacts from 400–1300 AD. The study, which contributes to the field of music archaeology, aims to provide a gateway to ancient soundworlds and ideas of music making. The research questions include: Where did these metal artefacts come from? How did they sound? How were they used? What did their sound mean to the people of the Iron Age? The data collected at the National Museum of Finland and at several provincial museums covers a total of 486 bells, pellet bells and bell pendants. By means of a cluster analysis, each category was divided into several subgroups. The subgroups, which all seem to have a different dating and geographical distribution, represent a spread of both local and international manufacturing traditions. According to an elemental analysis, the material varies from iron to copper-tin, copper-lead and copper-tin-lead alloys. Clappers, pellets and pebbles prove that the bells and pellet bells were indisputably instruments intended for sound production. Clusters of small bell pendants, however, probably produced sound by jingling against each other. Spectrogram plots reveal that the partials of the still audible sounds range from 1 000 to 19 850 Hz. On the basis of 129 inhumation graves, hoards, barrows and stray finds, it seems evident that the bells, pellet bells and bell pendants were fastened to dresses and horse harnesses or carried in pouches and boxes. The resulting acoustic spaces could have been employed in constructing social hierarchies, since the instruments usually appear in richly furnished graves. Furthermore, the instruments repeatedly occur with crosses, edge tools and zoomorphic pendants that in the later Finnish-Karelian culture were regarded as prophylactic amulets. In the Iron Age as well as in later folk culture, the bell sounds seem to have expressed territorial, social and cosmological boundaries.

1H and 13C NMR study of pyridylamides and thionamides

1H and 13C NMR spectra are reported for several pyridylamides and thionamides. Complete analyses of the 13C spectra have yielded the chemical shifts and the direct and long range (13C, 1H) coupling constants. 13C chemical shifts show linear relationship with charge densities computed by the CNDO method. The variations in the chemical shifts are discussed.

Population ecology of Heteronyx piceus (Coleoptera: Scarabaeidae) in a peanut/maize cropping system

Large larval populations of the scarabaeid beetle Heteronyx piceus Blanchard that occur under peanuts, but not maize, in the South Burnett region of Australia are the result of a high rate and prolonged period of egg production by females feeding on peanut foliage. Heteronyx piceus is a relatively sedentary species and movement of females between adjacent fields is low. Populations of H. piceus varied markedly with landscape position. High larval populations are more likely (1 in 4 chance) to be encountered on the ‘scrub’ soils in the upper parts of the landscape than in the ‘forest’ soils in the lower half (1 in 20 chance), indicating that soil type/landscape position is a key risk factor in assessing the need for management intervention. The studies indicate that, because of the species' sedentary nature, the most meaningful population entity for management of H. piceus is the individual field, rather than the whole-farm or the region. The implications of this population ecology for management of the pest are discussed in relation to control strategies.

Genotypic variation in seedling root architectural traits and implications for drought adaptation in wheat (Triticum aestivum L.)

Root system characteristics are of fundamental importance to soil exploration and below-ground resource acquisition. Root architectural traits determine the in situ space-filling properties of a root system or root architecture. The growth angle of root axes is a principal component of root system architecture that has been strongly associated with acquisition efficiency in many crop species. The aims of this study were to examine the extent of genotypic variability for the growth angle and number of seminal roots in 27 current Australian and 3 CIMMYT wheat (Triticum aestivum L.) genotypes, and to quantify using fractal analysis the root system architecture of a subset of wheat genotypes contrasting in drought tolerance and seminal root characteristics. The growth angle and number of seminal roots showed significant genotypic variation among the wheat genotypes with values ranging from 36 to 56 (degrees) and 3 to 5 (plant-1), respectively. Cluster analysis of wheat genotypes based on similarity in their seminal root characteristics resulted in four groups. The group composition reflected to some extent the genetic background and environmental adaptation of genotypes. Wheat cultivars grown widely in the Mediterranean environments of southern and western Australia generally had wider growth angle and lower number of seminal axes. In contrast, cultivars with superior performance on deep clay soils in the northern cropping region, such as SeriM82, Baxter, Babax, and Dharwar Dry exhibited a narrower angle of seminal axes. The wheat genotypes also showed significant variation in fractal dimension (D). The D values calculated for the individual segments of each root system suggested that, compared to the standard cultivar Hartog, the drought-tolerant genotypes adapted to the northern region tended to distribute relatively more roots in the soil volume directly underneath the plant. These findings suggest that wheat root system architecture is closely linked to the angle of seminal root axes at the seedling stage. The implications of genotypic variation in the seminal root characteristics and fractal dimension for specific adaptation to drought environment types are discussed with emphasis on the possible exploitation of root architectural traits in breeding for improved wheat cultivars for water-limited environments.

Propagating waves in polar coronal holes as seen by SUMER and EIS

Context. To study the dynamics of coronal holes and the role of waves in the acceleration of the solar wind, spectral observations were performed over polar coronal hole regions with the SUMER spectrometer on SoHO and the EIS spectrometer on Hinode. Aims. Using these observations, we aim to detect the presence of propagating waves in the corona and to study their properties. Methods. The observations analysed here consist of SUMER spectra of the Ne VIII 770 angstrom line (T = 0.6 MK) and EIS slot images in the Fe XII 195 angstrom line (T = 1.3 MK). Using the wavelet technique, we study line radiance oscillations at different heights from the limb in the polar coronal hole regions. Results. We detect the presence of long period oscillations with periods of 10 to 30 min in polar coronal holes. The oscillations have an amplitude of a few percent in radiance and are not detectable in line-of-sight velocity. From the time distance maps we find evidence for propagating velocities from 75 km s(-1) (Ne VIII) to 125 km s(-1)(Fe XII). These velocities are subsonic and roughly in the same ratio as the respective sound speeds. Conclusions. We interpret the observed propagating oscillations in terms of slow magneto-acoustic waves. These waves can be important for the acceleration of the fast solar wind.

Phase relations between Al2O3---Cr2O3 and FeAl2O4---FeCr2O4 solid solutions at 1823 K

Tie-lines between the corundum and spinel solid solutions have been determined experimentally at 1823 K. Next, activities of FeCr2O4 and FeAl2O4 in the spinel solid solution were determined by combining the tie-line data with literature values for the activities of Cr2O3 and Al2O3 in the corundum phase. Activities and the Gibbs energy of mixing for the spinel solid solution were also obtained from a model based on cation distribution between nonequivalent crystallographic sites in the oxide lattice. The difference between the Gibbs energy of mixing obtained experimentally and from the model has been attributed to a strain enthalpy term which is relatively unchanged in magnitude from the reported at 1373 K. The integral enthalpy of mixing obtained from experimental data at 1373 and 1823 K using the second law is compared with the model result.

The host range and biology of Cometaster pyrula; a biocontrol agent for Acacia nilotica subsp. indica in Australia

Prickly acacia, Acacia nilotica subsp. indica (Benth.) Brenan, a major weed of the Mitchell Grass Downs of northern Queensland, Australia, has been the target of biological control projects since the 1980s. The leaf-feeding caterpillar Cometaster pyrula (Hopffer) was collected from Acacia nilotica subsp. kraussiana (Benth.) Brenan during surveys in South Africa to find suitable biological control agents, recognised as a potential agent, and shipped into a quarantine facility in Australia. Cometaster pyrula has a life cycle of approximately 2 months during which time the larvae feed voraciously and reach 6 cm in length. Female moths oviposit a mean of 339 eggs. When presented with cut foliage of 77 plant species, unfed neonates survived for 7 days on only Acacia nilotica subsp. indica and Acacia nilotica subsp. kraussiana. When unfed neonates were placed on potted plants of 14 plant species, all larvae except those on Acacia nilotica subsp. indica and Acacia nilotica subsp. kraussiana died within 10 days of placement. Cometaster pyrula was considered to be highly host specific and safe to release in Australia. Permission to release C. pyrula in Australia was obtained and the insect was first released in north Queensland in October 2004. The ecoclimatic model CLIMEX indicated that coastal Queensland was climatically suitable for this insect but that inland areas were only marginally suitable.

Identifying statutory encumbrances for seller disclosure

The standard land contracts in Queensland require a seller of land to disclose to a buyer not only registered encumbrances, but also statutory encumbrances affecting the land. Whether a statute creates a statutory encumbrance over the title to the property is therefore a key question for a seller when completing a contract. This article examines relevant case law and provides some guidelines for when a statute creates a statutory encumbrance that should be disclosed to a buyer as a defect in title.

Pressure shocks in relativistic viscous heat-conducting fluids

In this paper we have studied the propagation of pressure shocks in viscous, heat-conducting, relativistic fluids. Velocities of wave fronts and growth equations for the strength of the waves are obtained in the case of low and high temperatures with variable transport coefficients. On the basis of numerical integrations the growth equation results have been discussed. In the case of constant transport coefficients and for all admissible values of ratio of specific heats of the fluid, an analytical solution for the velocity of the wave as a function of distance along the normal trajectory to the wave front, has been obtained.