A novel theoretical approach to passive control of thermo-acoustic oscillations: Application to ducted heat sources

In this paper, we develop a linear technique that predicts how the stability of a thermo-acoustic system changes due to the action of a generic passive feedback device or a generic change in the base state. From this, one can calculate the passive device or base state change that most stabilizes the system. This theoretical framework, based on adjoint equations, is applied to two types of Rijke tube. The first contains an electrically-heated hot wire and the second contains a diffusion flame. Both heat sources are assumed to be compact so that the acoustic and heat release models can be decoupled. We find that the most effective passive control device is an adiabatic mesh placed at the downstream end of the Rijke tube. We also investigate the effects of a second hot wire and a local variation of the cross-sectional area but find that both affect the frequency more than the growth rate. This application of adjoint sensitivity analysis opens up new possibilities for the passive control of thermo-acoustic oscillations. For example, the influence of base state changes can be combined with other constraints, such as that the total heat release rate remains constant, in order to show how an unstable thermo-acoustic system should be changed in order to make it stable. Copyright © 2013 by ASME.

Investigation of a radial-inflow bleed as a potential for compressor clearance control

The mismatch in thermal response between a High Pressure Compressor (HPC) drum and casing is a limiting factor in the reduction of compressor clearance. An experimental test rig has been used to demonstrate the concept of radial inflow to reduce the thermal time constant of HPC discs. The testing uses a simulated idle - Maximum Take Off (MTO) - idle transient in order to measure the thermal response directly. The testing is fully scaled in the dimensionless sense to engine conditions. A simple closure model based on lumped capacitance is used to illustrate the scope of potential benefits. The proof-of-concept testing shows that HPC disc time constant reductions of the order 2 are feasible with a radial-inflow bleed of only 4% of bore flow at scaled MTO conditions. Using the experimental results, the simple closure modelling suggests that for a stage with a significant mismatch in thermal response, reductions in 2D axis-symmetric clearance of as much as 50% at MTO conditions may be possible along with significant scope for improvements at cruise conditions. Copyright © 2013 by ASME.

CFD investigation of turbulent premixed flame response to transverse forcing

Screech is a high frequency oscillation that is usually characterized by instabilities caused by large-scale coherent flow structures in the wake of bluff-body flameholders and shear layers. Such oscillations can lead to changes in flame surface area which can cause the flame to burn unsteadily, but also couple with the acoustic modes and inherent fluid-mechanical instabilities that are present in the system. In this study, the flame response to hydrodynamic oscillations is analyzed in a controlled manner using high-fidelity Computational Fluid Dynamics (CFD) with an unsteady Reynolds-averaged Navier-Stokes approach. The response of a premixed flame with and without transverse velocity forcing is analyzed. When unforced, the flame is shown to exhibit a self-excitation that is attributed to the anti-symmetric shedding of vortices in the wake of the flameholder. The flame is also forced using two different kinds of low-amplitude out-of-phase inlet velocity forcing signals. The first forcing method is harmonic forcing with a single characteristic frequency, while the second forcing method involves a broadband forcing signal with frequencies in the range of 500 - 1000 Hz. For the harmonic forcing method, the flame is perturbed only lightly about its mean position and exhibits a limit cycle oscillation that is characteristic of the forcing frequency. For the broadband forcing method, larger changes in the flame surface area and detachment of the flame sheet can be seen. Transition to a complicated trajectory in the phase space is observed. When analyzed systematically with system identification methods, the CFD results, expressed in the form of the Flame Transfer Function (FTF) are capable of elucidating the flame response to the imposed perturbation. The FTF also serves to identify, both spatially and temporally, regions where the flame responds linearly and nonlinearly. Locking-in between the flame's natural self-excited frequency and the subharmonic frequencies of the broadband forcing signal is found to alter the dynamical behaviour of the flame. Copyright © 2013 by ASME.

Computational engineering design for micro-scale combustion devices: A thermally improved configuration

A multi-objective design optimisation study has been carried out with the objectives to improve the overall efficiency of the device and to reduce the fuel consumption for the proposed micro-scale combustor design configuration. In a previous study we identified the topology of the combustion chamber that produced improved behaviour of the device in terms of the above design criteria. We now extend our design approach, and we propose a new configuration by the addition of a micro-cooling channel that will improve the thermal behaviour of the design as previously suggested in literature. Our initial numerical results revealed an improvement of 2.6% in the combustion efficiency when we applied the micro-cooling channel to an optimum design configuration we identified from our earlier multi-objective optimisation study, and under the same operating conditions. The computational modelling of the combustion process is implemented in the commercial computational fluid dynamics package ANSYS-CFX using Finite Rate Chemistry and a single step hydrogen-air reaction. With this model we try to balance good accuracy of the combustion solution and at the same time practicality within the context of an optimisation process. The whole design system comprises also the ANSYS-ICEM CFD package for the automatic geometry and mesh generation and the Multi-Objective Tabu Search algorithm for the design space exploration. We model the design problem with 5 geometrical parameters and 3 operational parameters subject to 5 design constraints that secure practicality and feasibility of the new optimum design configurations. The final results demonstrate the reliability and efficiency of the developed computational design system and most importantly we assess the practicality and manufacturability of the revealed optimum design configurations of micro-combustor devices. Copyright © 2013 by ASME.

Population status, threats and conservation of the Yangtze finless porpoise

The Yangtze finless porpoise (Neophocaena phocaenoides asiaeorientalis) is currently limited to the middle and lower reaches of the Yangtze River from Yichang to Shanghai, China, and the adjoining Poyang and Dongting Lakes. Its population size has decreased remarkably during the last several decades due to the heavy impact of human activities, including overfishing of prey species, water development projects that cause attendant habitat loss and degradation, water pollution, and accidental deaths caused by harmful fishing gear and collisions with motorized vessels. It was estimated that the number of remaining individuals was down to approximately 1800 in 2006, a number that is decreasing at a rate as high as 5% per year. Three conservation measures - in situ and ex situ conservation and captive breeding have been applied to the protection of this unique porpoise since the early 1990s. Seven natural and two "semi-natural" reserves have so far been established. Since 1996, a small group of finless porpoises has been successfully reared in a facility at the Institute of Hydrobiology of the Chinese Academy of Sciences; three babies were born in captivity on July 5, 2005, June 2, 2007 and July 5, 2008. These are the first freshwater cetaceans ever born in captivity in the world. Several groups of these porpoises caught in the main stream of the Yangtze River, or rescued, have been introduced into the Tian'e-Zhou Semi-natural Reserve since 1990. These efforts have proven that, not only can these animals survive in the area, they are also to reproduce naturally and successfully. More than 30 calves had been born in the reserve since then, with one to three born each year. Taking deaths and transfers into account, there were approximately 30 individuals living in the reserve as of the end of 2007. Among eight mature females captured in April 2008, five were confirmed pregnant. This effort represents the first successful attempt at off-site protection of a cetacean species in the world, and establishes a solid base for conservation of the Yangtze finless porpoise. A lesson must be drawn from the tragedy of Chinese River Dolphin (Lipotes vexillifer), which has already been declared likely extinct. Strong, effective and appropriate protective measures must be carried out quickly to prevent the Yangtze finless porpoise from becoming a second Chinese River Dolphin, and save the biodiversity of the Yangtze River as a whole.

How polluted is the Yangtze River? Water quality downstream from the Three Gorges Dam

The concentrations of major anions and cations, nitrogen and phosphorus, dissolved and particulate trace elements, and organic pollutants were determined for the middle and lower reaches of the Yangtze River (Changjiang) from below the Three Gorges Dam (TGD) to the mouth at Shanghai in November 2006. The concentration of dissolved inorganic phosphate (DIP) was constant at a low level of 6-8 mu gP/L, but the concentration of nitrate (NO3-) approximately doubled downstream and was closely correlated with K+. This translated to a daily load of well over 1000 It of dissolved inorganic nitrogen (DIN) at Datong. The average concentrations of dissolved Pb (0.078 +/- 0.023 mu g/L), Cd (0.024 +/- 0.009 mu g/L), Cr(0.57 +/- 0.09 mu g/L), Cu (1.9 +/- 0.7 mu g/L), and Ni (0.50 +/- 0.49 mu g/L) were comparable with those in other major world rivers, while As (3.3 +/- 1.3 mu g/L) and Zn (1.5 +/- 0.6 mu g/L) were higher by factors of 5.5 and 2.5, respectively. The trace element contents of suspended particles of As (31 +/- 28 mu g/g), Pb (83 +/- 34 mu g/g), and Ni (52 +/- 16 mu g/g) were close to maximum concentrations recommended for rivers by the European Community (EC). The average concentrations of Cd (2.6 +/- 1.6 mu g/g), Cr (185 +/- 102 mu g/g), Cu (115 +/- 106 mu g/g), and Zn (500 +/- 300 mu g/g) exceeded the EC standards by a factor of two, and Hg (4.4 +/- 4.7 mu g/g) by a factor of 4 to 5. Locally occurring peak concentrations exceed these values up to fourfold, among them the notorious elements As, Hg, and Tl. All dissolved and particulate trace element concentrations were higher than estimates made twenty years ago [Zhang, J., Geochemistry of trace metals from Chinese river/estuary systems: an overview. Estuar Coast Shelf Sci 1995; 41: 631-658.]. The enormous loads of anthropogenic pollutants disposed to the river were diluted by the large water discharge of the Yangtze even during the lowest flow resulting in the relatively low concentration levels of trace elements and organic pollutants observed. We estimated loads of e.g. As, Pb and Ni to the East China Sea to be about 4600 kg As d(-1), 3000 kg Pb d(-1), and 2000 kg Ni d(-1). About 6000 t d(-1) of dissolved organic carbon (DOC) was delivered into the sea at the time of our cruise. We tested for 236 organic pollutants, and only the most infamous were found to be barely above detection limits. We estimated that the load of chlorinated compounds, aromatic hydrocarbons, phenols, and PAHs were between 500 and 3500 kg d(-1). We also detected eight herbicides entering the estuary with loads of 5-350 kg d(-1). The pollutant load, even when at low concentrations, are considerable and pose an increasing threat to the health of the East China Sea ecosystem. (c) 2008 Elsevier B.V. All rights reserved.

Perfluorinated compounds in the Pearl River and Yangtze River of China

A total of 14 perfluorinated compounds (PFCs) were quantified in river water samples collected from tributaries of the Pearl River (Guangzhou Province, south China) and the Yangtze River (central China). Among the PFCs analyzed, perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA) were the two compounds with the highest concentrations. PFOS concentrations ranged from 0.90 to 99 ng/1 and < 0.01-14 ng/1 in samples from the Pearl River and Yangtze River, respectively; whereas those for PFOA ranged from 0.85 to 13 ng/l and 2.0-260 ng/l. Lower concentrations were measured for perfluorobutane sulfonate (PFBS), perfluorohexane sulfonate (PFHxS), perfluorooctanesulfoamide (PFOSA), perfluorohexanoic acid (PFHxA), perfluoroheptanoic acid (PFHpA), perfluorononaoic acid (PFNA), perfluorodecanoic acid (PFDA), and perfluoroundecanoic acid (PFUnDA). Concentrations of several perfluorocarboxylic acids, including perfluorododecanoic acid (PFDoDA), perfluorotetradecanoic acid (PFTeDA), perfluorohexadecanoic acid (PFHxDA) and perfluorooctadecanoic acid (PFOcDA) were lower than the limits of quantification in all the samples analyzed. The highest concentrations of most PFCs were observed in water samples from the Yangtze River near Shanghai, the major industrial and financial centre in China. In addition, sampling locations in the lower reaches of the Yangtze River with a reduced flow rate might serve as a final sink for contaminants from the upstream river runoffs. Generally, PFOS was the dominant PFC found in samples from the Pearl River, while PFOA was the predominant PFC in water from the Yangtze River. Specifically, a considerable amount of PFBS (22.9-26.1% of total PFC analyzed) was measured in water collected near Nanjing, which indicates the presence of potential sources of PFBS in this part of China. Completely different PFC composition profiles were observed for samples from the Pearl River and the Yangtze River. This indicates the presence of dissimilar sources in these two regions. (c) 2007 Elsevier Ltd. All rights reserved.

Hermetically-coated superparamagnetic Fe2O3 particles with SiO2 nanofilms

Magnetic nanoparticles are frequently coated with SiO2to improve their functionality and bio-compatibility in a range of biomedical and polymer nanocomposile applications. In this paper, a scalable flame aerosol technology is used to produce highly dispersible, superparamagnetic iron oxide nanoparticles hermetically coaled with silica to retain full magnetization performance. Iron oxide particles were produced by flame spray pyrolysis (FSP) of iron acelylacetonale in xylene/acetonitrile solutions, and the resulting aerosol was in situ coaled with SiO2 by oxidation of swirling hexamethlydisiloxane vapor. The process allows independent control of the core Fe2O3, particle properties and the thickness of their silica coaling film. This ensures that the non-magnetic SiO2 layer can be closely controlled and minimized. The optimal SiO2 content for complete (hermetic) encapsulation of the magnetic core particles was determined by isopropanol chemisorption. The magnetization of Fe2O3 coated with about 2 nm thin SiO2 layers was nearly identical lo that of uncoated, pure Fe2O3 nanoparlicles.

Range-wide Yangtze freshwater dolphin expedition: The last chance to see Baiji?

Background, Aim and Scope. There are two species of fresh water cetaceans surviving in the Yangtze River system in China: Baiji (Lipotes vexillifer) and Yangtze finless porpoise (Neophocaena phocaenoides asiaeorientalis). As a result of the expansion of human activities on the river, their distribution ranges appear to be decreasing and in the case of the Baiji, are even being restricted to several sections. The Baiji is the world's most critically endangered cetacean species with a population estimated at only a few tens of individuals. The Yangtze finless porpoise is the world's only freshwater-adapted population of the species, and it has been estimated that only around 1,000 individuals remain in the river system. In order to prevent the extinction of Baiji and a sharp decline in the abundance of the porpoise, in situ conservation (i.e. in the river) and two ex situ conservation (i.e. in semi-natural reserves and in captivity) strategies were proposed and have been implemented since the early 1990s. In view of both the severely endangered status of the animals and the severely degraded conditions of their habitats, the feasibility and actual status of these two strategies are raised for discussion. Main Features. The threats faced by the cetaceans are mainly from the unfettered exploitation of the river's resources. In the past 20 years, five nature reserves have been established along the river. Imposing maximum prohibition of harmful and illegal fishing methods in the reserves might prolong the process of extinction of these cetaceans in the wild, but so far, the administrative measures taken in the reserves have not yet kept the abundance from sharply declining. As human use of the river and its resources is expected to intensify for many decades into the future, the ability of the river to continue to support these species is certainly undecided. Therefore, rescuing animals from the river and establishing viable breeding populations in semi-natural reserves, in which the environment is similar to the main stream of the river, and in captivity, has to be considered urgently as the short-term goal of ex situ strategies. Since the abundance of porpoises is higher than that of the Baiji, we have first established breeding populations of them in the semi-natural reserves and in captivity. But, considering the extremely low density of Baiji in the river, an immediate range-wide Yangtze Baiji survey is an urgent need for locating and capturing sufficient Baiji for successfully establishing a breeding population of them in semi-natural reserves. Results. Two semi-natural reserves (in Shishou, Hubei Province, and Tongling, Anhui Province) have been set up along the river in order to establish breeding populations of the Baiji and the porpoises. So far, several small groups of porpoises that were caught in the main stream of the river have successively been introduced into the semi-natural reserves. Under careful management, these animals in both of the semi-natural reserves not only survive, but can also reproduce naturally and successfully. At least one or three calves were born in each reserve each year. Additionally, a breeding group of porpoises is being established at the Baiji Dolphinarium at the Institute of Hydrobiology, Chinese Academy of Sciences, Wuhan. There are presently four adults and one calf living in the Dolphinarium. The calf, born in July, 2005, is the first captive bred Yangtze Finless Porpoise in the world. In preparation for the range-wide Yangtze cetacean survey, a 9-day pilot expedition on the river near Wuhan was conducted in March, 2006, in order to develop methods for locating the Baiji. No Baiji were expected to be seen in such a short period but about 40 porpoise sightings were observed. Results of the pilot survey indicated that traditional visual and acoustical survey methods for cetaceans should be adapted to find the elusive Baiji in the river. Currently, the range-wide Yangtze cetacean survey is in preparation. The survey will cover over 1,700 km of the Yangtze River from Yichang to Shanghai, and is expected to provide detailed information on Baiji and porpoise numbers and distribution patterns in the river. Discussion. Although the short-term goal of ex situ conservation is to rescue cetaceans from the river and to establish viable breeding populations in semi-natural reserves and in captivity, the long-term goal of releasing the animals back into the river when the threats have decreased and the natural environment has been improved, should not be neglected. Moreover, the in situ conservation efforts in the natural reserves, and even in the entire Yangtze River system, including the lakes, should not be ignored or abandoned at any time. The activities contributing to the conservation of the Baiji and the porpoise in the wild have the incidental effect of benefiting the entire Yangtze ecosystem and other rare threatened species. The dynamics of the groups of porpoises in semi-natural reserves should be monitored continually, in order to guide the establishment of breeding groups of Baiji in these semi-natural reserves in the near future. Conclusions. Under the existing severely degraded conditions of the Yangtze system, the sharply fall populations of Baiji and porpoises will not be suspended in the foreseeable future. Therefore, ex situ conservation should be emphasized, and the severely threatened Baiji in the river should be removed and translocated to semi-natural reserves for establishing viable breeding populations. The successful program of capturing, translocating and maintaining finless porpoises in the Shishou semi-natural reserve has demonstrated its adequacy as an ex situ environment for cetaceans. Following the successful pilot survey in the river, the immediate range-wide Yangtze cetacean survey is proposed and is in preparation. The range-wide survey is expected to ensure that any remaining Baiji can be found reliably and captured successfully after the survey. Recommendations and Perspectives. During the range-wide survey, not only the Baiji but also the porpoise as well as their habitats should be investigated based on visual and acoustical methods that adapted to the river and the animals. Meanwhile, the current risk levels to the Baiji and porpoises should be evaluated at each area where Baiji or porpoises can be reliably sighted. Any capture efforts should be targeted on the most threatened areas, or where there is maximum risk of injury or death. The immediate track of the Baiji should be carried out once a Baiji is sighted during the range-wide survey in order to obtain the movement route of the animals, which is crucial information for the successful capture operation. Additionally, the need to establish new semi-natural reserves for the porpoises should be placed on the agenda of local and central governments in the near future.

Study of GaN epilayers growth on freestanding Si cantilevers

Five-micron thick freestanding Si cantilevers were fabricated on bulk Si (1 1 1) substrates with surface/bulk micromachining (SBM) process. Then 1-mu m thick GaN layers were deposited on the Si cantilevers by metal-organic chemical vapor deposition (MOCVD). Epilayers on cantilever areas were obtained crack-free, and the photoluminescence (PL) spectra verified the stress reduction and better material quality in these suspended parts of GaN. Back sides of the cantilevers were also covered with GaN layers, which prevented the composite beams from bending dramatically. This paper had proved the feasibility of integrating high-quality GaN epilayers with Si micromechanical structures to realize GaN-based micro electro-mechanical system (MEMS). (C) 2009 Elsevier Ltd. All rights reserved.

Ferromagnetic modification of GaN film by Cu+ ions implantation

The structural and magnetic properties of Cu+ ions-implanted GaN films have been reported. Eighty kilo-electron-volt Cu+ ions were implanted into n-type GaN film at room temperature with fluences ranging from 1 x 10(16) to 8 x 10(16) cm(-2) and subsequently annealed at 800 degrees C for 1 h in N-2 ambient. PIXE was employed to determine the Cu-implanted content. The magnetic property was measured by the Quantum Design MPMS SQUID magnetometer. No secondary phases or clusters were detected within the sensitivity of XRD. Raman spectrum measurement showed that the Cu ions incorporated into the crystal lattice positions of GaN through substitution of Ga atoms. Apparent ferromagnetic hysteresis loops measured at 10 K were presented. The experimental result showed that the ferromagnetic signal strongly increased with Cu-implanted fluence from 1 x 10(16) to 8 x 10(16) cm(-2).

Structural, elastic, and electronic properties of cubic perovskite BaHfO3 obtained from first principles

We investigated the structural, elastic, and electronic properties of the cubic perovskite-type BaHfO3 using a first-principles method based on the plane-wave basis set. Analysis of the band structure shows that perovskite-type BaHfO3 is a wide gap indirect semiconductor. The band-gap is predicted to be 3.94 eV within the screened exchange local density approximation (sX-LDA). The calculated equilibrium lattice constant of this compound is in good agreement with the available experimental and theoretical data reported in the literatures. The independent elastic constants (C-11, C-12, and C-44), bulk modules B and its pressure derivatives B', compressibility beta, shear modulus G, Young's modulus Y, Poisson's ratio nu, and Lame constants (mu, lambda) are obtained and analyzed in comparison with the available theoretical and experimental data for both the singlecrystalline and polycrystalline BaHfO3. The bonding-charge density calculation make it clear that the covalent bonds exist between the Hf and 0 atoms and the ionic bonds exist between the Ba atoms and HfO3 ionic groups in BaHfO3. (C) 2009 Elsevier B.V. All rights reserved.

EPITAXIAL LATERAL OVERGROWTH OF GaN ON SILICON-ON-INSULATOR

From a single process, GaN layers were laterally overgrown on maskless stripe-patterned (111) silicon-on-insulator (SOI) substrates by metalorganic chemical vapor deposition. The influence of stress on the behavior of dislocations at the coalescence during growth was observed using transmission electron microscopy (TEM). Improvement of the crystallin equality of the GaN layer was demonstrated by TEM and micro-Raman spectroscopy. Furthermore, the benefits of SOI substrates for GaN growth are also discussed.