An insight into dapsone co-crystals: sulfones as participants in supramolecular interactions

Agência Financiadora: Fundação para a Ciência e a Tecnologia - Pest-OE/QUI/UI0100/2013; PTDC/CTM-BPC/122447/2010; RECI/QEQ-QIN/0189/2012; SFRH/BPD/78854/2011

Development of an FIA system with amperometric detection for determination of bentazone in estuarine waters

On the basis of its electrochemical behaviour a new flow-injection analysis (FIA) method with amperometric detection has been developed for quantification of the herbicide bentazone (BTZ) in estuarine waters. Standard solutions and samples (200 µL) were injected into a water carrier stream and both pH and ionic strength were automatically adjusted inside the manifold. Optimization of critical FIA conditions indicated that the best analytical results were obtained at an oxidation potential of 1.10 V, pH 4.5, and an overall flow-rate of 2.4 mL min–1. Analysis of real samples was performed by means of calibration curves over the concentration range 2.5x10–6 to 5.0x10–5 mol L–1, and results were compared with those obtained by use of an independent method (HPLC). The accuracy of the amperometric determinations was ascertained; errors relative to the comparison method were below 4% and sampling rates were approximately 100 samples h–1. The repeatability of the proposed method was calculated by assessing the relative standard deviation (%) of ten consecutive determinations of one sample; the value obtained was 2.1%.

Nanohybrid materials as transducer surfaces for electrochemical sensing applications

A nanohybrid electrochemical transducer surface was developed using carbon and gold nanomaterials. The strategy relayed on casting multiwalled carbon nanotubes or carbon nanofibers onto a screen-printed carbon electrode surface, followed by in situ generation of gold nanoparticles by electrochemical deposition of ionic gold, in a reproducible manner. These transducers, so fabricated, were characterized using both electrochemical and microscopic techniques. Biofunctionality was evaluated using the streptavidin-biotin interaction system as the biological reaction model. These platforms allow to achieve low detection limits (in the order of pmoles), are reproducible and stable at least for a month after their preparation, being a perfect candidate to be used as transducer of different sensor devices.

Maltol determination in food by microwave assisted extraction and electrochemical detection

An electrochemical method is proposed for the determination of maltol in food. Microwave-assisted extraction procedures were developed to assist sample pre-treating steps. Experiments carried out in cyclic voltammetry showed an irreversible and adsorption controlled reduction of maltol. A cathodic peak was observed at -1.0 V for a Hanging Mercury Drop Electrode versus an AgCl/Ag (in saturated KCl), and the peak potential was pH independent. Square wave voltammetric procedures were selected to plot calibration curves. These procedures were carried out with the optimum conditions: pH 6.5; frequency 50 Hz; deposition potential 0.6 V; and deposition time 10 s. A linear behaviour was observed within 5.0 × 10-8 and 3.5 × 10-7 M. The proposed method was applied to the analysis of cakes, and results were compared with those obtained by an independent method. The voltammetric procedure was proven suitable for the analysis of cakes and provided environmental and economical advantages, including reduced toxicity and volume of effluents and decreased consumption of reagents.

Screening of grapes and wine for azoxystrobin, kresoxim-methyl and trifloxystrobin fungicides by HPLC with diode array detection

The Quinone outside Inhibitors (QoI) are one of the most important and recent fungicide groups used in viticulture and also allowed by Integrated Pest Management. Azoxystrobin, kresoxim-methyl and trifloxystrobin are the main active ingredients for treating downy and powdery mildews that can be present in grapes and wines. In this paper, a method is reported for the analysis of these three QoI-fungicides in grapes and wine. After liquid–liquid extraction and a clean-up on commercial silica cartridges, analysis was by isocratic HPLC with diode array detection (DAD) with a run time of 13 min. Confirmation was by solid-phase micro-extraction (SPME), followed by GC/MS determination. The main validation parameters for the three compounds in grapes and wine were a limit of detection up to 0.073mg kg-1, a precision not exceeding 10.0% and an average recovery of 93% ±38.

Áreas de vulnerabilidade para co-infecção HIV-aids/TB em Ribeirão Preto, SP

OBJETIVO: Identificar áreas de vulnerabilidade para os casos novos de co-infecção HIV/tuberculose (TB). MÉTODOS: Estudo descritivo ecológico realizado por meio do georreferenciamento dos casos novos de HIV/TB notificados em Ribeirão Preto, SP, em 2006. Os dados foram obtidos do sistema de informação estadual paulista de notificação de TB. Os casos novos de co-infecção HIV/TB foram analisados conforme características sociodemográficas e clínicas e, posteriormente, georreferenciados na base cartográfica do município segundo endereço residencial. Os setores do município foram categorizados em três níveis socioeconômicos: inferior, intermediário e superior, com base na análise de componentes principais das variáveis do censo demográfico de 2000 (renda, instrução e percentagem de domicílios com cinco ou mais moradores). Foi calculada a incidência da co-infecção HIV/TB para cada nível socioeconômico. RESULTADOS: A co-infecção HIV/TB acometeu mais adultos do sexo masculino em idade economicamente ativa e a forma pulmonar da TB foi a mais comum. A distribuição espacial mostrou que as incidências nas áreas com níveis socioeconômicos intermediários e inferiores (8,3 e 11,5 casos por 100 mil habitantes, respectivamente) foram superiores àquela (4,8 casos por 100 mil habitantes) de nível socioeconômico superior. CONCLUSÕES: A taxa de incidência de co-infecção HIV/TB analisada por níveis socioeconômicos mostrou padraÞo espacial de distribuiçaÞo não homogêneo e apresentou valores mais altos em áreas de maior vulnerabilidade social. O estudo diagnosticou aìreas geograìficas prioritaìrias para o controle da co-infecção e a tecnologia do sistema de informação geográfica pode ser empregada no planejamento das ações em saúde pelos gestores municipais.

Multiplexed electrochemical immunosensor for detection of celiac disease serological markers

Celiac disease (CD) is a gluten-induced autoimmune enteropathy characterized by the presence of antibodies against gliadin (AGA) and anti-tissue transglutaminase (anti-tTG) antibodies. A disposable electrochemical dual immunosensor for the simultaneous detection of IgA and IgG type AGA and antitTG antibodies in real patient’s samples is presented. The proposed immunosensor is based on a dual screen-printed carbon electrode, with two working electrodes, nanostructured with a carbon–metal hybrid system that worked as the transducer surface. The immunosensing strategy consisted of the immobilization of gliadin and tTG (i.e. CD specific antigens) on the nanostructured electrode surface. The electrochemical detection of the human antibodies present in the assayed serum samples was carried out through the antigen–antibody interaction and recorded using alkaline phosphatase labelled anti-human antibodies and a mixture of 3-indoxyl phosphate with silver ions was used as the substrate. The analytical signal was based on the anodic redissolution of enzymatically generated silver by cyclic voltammetry. The results obtained were corroborated with commercial ELISA kits indicating that the developed sensor can be a good alternative to the traditional methods allowing a decentralization of the analyses towards a point-of-care strategy.

Previsão de desempenho para redes móveis LTE e UMTS baseadas em redes GSM co-localizadas

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Electrónica e Telecomunicações

Detection of ZnS phases in CZTS thin-films by EXAFS

Copper zinc tin sulfide (CZTS) is a promising Earthabundant thin-film solar cell material; it has an appropriate band gap of ~1.45 eV and a high absorption coefficient. The most efficient CZTS cells tend to be slightly Zn-rich and Cu-poor. However, growing Zn-rich CZTS films can sometimes result in phase decomposition of CZTS into ZnS and Cu2SnS3, which is generally deleterious to solar cell performance. Cubic ZnS is difficult to detect by XRD, due to a similar diffraction pattern. We hypothesize that synchrotron-based extended X-ray absorption fine structure (EXAFS), which is sensitive to local chemical environment, may be able to determine the quantity of ZnS phase in CZTS films by detecting differences in the second-nearest neighbor shell of the Zn atoms. Films of varying stoichiometries, from Zn-rich to Cu-rich (Zn-poor) were examined using the EXAFS technique. Differences in the spectra as a function of Cu/Zn ratio are detected. Linear combination analysis suggests increasing ZnS signal as the CZTS films become more Zn-rich. We demonstrate that the sensitive technique of EXAFS could be used to quantify the amount of ZnS present and provide a guide to crystal growth of highly phase pure films.

Fracture toughness determination of adhesive and co-cured joints in natural fibre composites

Adhesive bonding has become more efficient in the last few decades due to the adhesives developments, granting higher strength and ductility. On the other hand, natural fibre composites have recently gained interest due to the low cost and density. It is therefore essential to predict the fracture behavior of joints between these materials, to assess the feasibility of joining or repairing with adhesives. In this work, the tensile fracture toughness (Gc n) of adhesive joints between natural fibre composites is studied, by bonding with a ductile adhesive and co-curing. Conventional methods to obtain Gc n are used for the co-cured specimens, while for the adhesive within the bonded joint, the J-integral is considered. For the J-integral calculation, an optical measurement method is developed for the evaluation of the crack tip opening and adherends rotation at the crack tip during the test, supported by a Matlab sub-routine for the automated extraction of these quantities. As output of this work, an optical method that allows an easier and quicker extraction of the parameters to obtain Gc n than the available methods is proposed (by the J-integral technique), and the fracture behaviour in tension of bonded and co-cured joints in jute-reinforced natural fibre composites is also provided for the subsequent strength prediction. Additionally, for the adhesively- bonded joints, the tensile cohesive law of the adhesive is derived by the direct method.

Tuberculosis in indigenous children in the Brazilian Amazon

OBJECTIVE: Assess the epidemiological aspects of tuberculosis in Brazilian indigenous children and actions to control it. METHODS: An epidemiological study was performed with 356 children from 0 to 14 years of age in Rondônia State, Amazon, Brazil, during the period 1997-2006. Cases of TB reported to the Notifiable Diseases Surveillance System were divided into indigenous and non-indigenous categories and analyzed according to sex, age group, place of residence, clinical form, diagnostic tests and treatment outcome. A descriptive analysis of cases and hypothesis test (χ²) was carried out to verify if there were differences in the proportions of illness between the groups investigated. RESULTS: A total of 356 TB cases were identified (125 indigenous, 231 non-indigenous) of which 51.4% of the cases were in males. In the indigenous group, 60.8% of the cases presented in children aged 0-4 years old. The incidence mean was much higher among indigenous; in 2001, 1,047.9 cases/100,000 inhabitants were reported in children aged < 5 years. Pulmonary TB was reported in more than 80% of the cases, and in both groups over 70% of the cases were cured. Cultures and histopathological exams were performed on only 10% of the patients. There were 3 cases of TB/HIV co-infection in the non-indigenous group and none in the indigenous group. The case detection rate was classified as insufficient or fair in more than 80% of the indigenous population notifications, revealing that most of the diagnoses were performed based on chest x-ray. CONCLUSIONS: The approach used in this study proved useful in demonstrating inequalities in health between indigenous and non-indigenous populations and was superior to the conventional analyses performed by the surveillance services, drawing attention to the need to improve childhood TB diagnosis among the indigenous population.

Caracterização química e ecotoxicológica de escórias e cinzas resultantes da co-combustão de lamas e carvão

Em 1999 a Fundação para a Ciência e a Tecnologia aprovou o financiamento do projecto “Behaviour of Heavy Metals on the Thermal Treatment of Residues” cujo acrónimo era Bimetal. Este projecto, cujos parceiros eram o Departamento de Engenharia Energética e Controlo Ambiental do Instituto Nacional de Engenharia e Tecnologia Industrial (INETI) e o Grupo de Disciplinas de Ecologia da Hidrosfera (GDEH) da Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa, tinha como objectivo a avaliação do comportamento de metais pesados durante a combustão de resíduos. Neste sentido, a equipa do INETI efectuou quatro ensaios de incineração: dois de mono-combustão de uma lama residual urbana, um de co-combustão de lama residual urbana e carvão e, finalmente, um de mono-combustão de carvão. Cada ensaio de incineração produziu uma cinza de fundo e duas cinzas volantes, provenientes de dois ciclones. A equipa do GDEH foi responsável pela caracterização físico-química e ecotoxicológica das cinzas provenientes dos ensaios realizados pela equipa do INETI. A avaliação incidiu em dois aspectos: 1) a determinação da composição das cinzas, relativamente a um dado conjunto de parâmetros físico-químicos considerados; e 2) produção de lixiviados a partir do contacto das cinzas com um agente lixiviante. Estes lixiviados foram submetidos à caracterização físico-química, relativamente a um dado conjunto de parâmetros físico-químicos e, ainda, à caracterização ecotoxicológica, recorrendo a dois indicadores biológicos. A determinação da composição das cinzas permitiu efectuar um balanço de massas dos ensaios de incineração realizados e, com isto, determinar as taxas de emissão, dos parâmetros analisados, para a atmosfera. Os ensaios de lixiviação permitiram classificar, de acordo com a metodologia de classificação de resíduos a que se recorreu, as doze cinzas produzidas pela equipa do INETI e os materiais que lhes deram origem, a areia do leito, o carvão e a lama residual urbana. De um modo geral, as duas cinzas volantes apresentaram uma concentração superior, dos parâmetros considerados, relativamente à cinza de fundo. Entre as duas cinzas volantes, a cinza do 2º ciclone apresentou um maior teor, relativamente aos parâmetros analisados, do que as cinzas do 1º ciclone.

Road lane detection for autonomous robot guidance

Computational Vision stands as the most comprehensive way of knowing the surrounding environment. Accordingly to that, this study aims to present a method to obtain from a common webcam, environment information to guide a mobile differential robot through a path similar to a roadway.

Detection of quasi-periodic processes in complex systems: how do we quantitatively describe their properties?

It has been shown that in reality at least two general scenarios of data structuring are possible: (a) a self-similar (SS) scenario when the measured data form an SS structure and (b) a quasi-periodic (QP) scenario when the repeated (strongly correlated) data form random sequences that are almost periodic with respect to each other. In the second case it becomes possible to describe their behavior and express a part of their randomness quantitatively in terms of the deterministic amplitude–frequency response belonging to the generalized Prony spectrum. This possibility allows us to re-examine the conventional concept of measurements and opens a new way for the description of a wide set of different data. In particular, it concerns different complex systems when the ‘best-fit’ model pretending to be the description of the data measured is absent but the barest necessity of description of these data in terms of the reduced number of quantitative parameters exists. The possibilities of the proposed approach and detection algorithm of the QP processes were demonstrated on actual data: spectroscopic data recorded for pure water and acoustic data for a test hole. The suggested methodology allows revising the accepted classification of different incommensurable and self-affine spatial structures and finding accurate interpretation of the generalized Prony spectroscopy that includes the Fourier spectroscopy as a partial case.