Síntese, caracterização e estudo das propriedades magnéticas de ortoferritas de lantânio dopadas com manganês

Orthoferrites AFeO3 (A = rare earth) are an important class of perovskite oxides that exhibit weak ferromagnetism. These materials find numerous applications as chemical sensors, cathodes for fuel cells and catalysis, which make them interesting from the standpoint of science and technology. Their structural, electrical and magnetic properties are dependent on many factors such as the preparation method, heat treatment conditions, chemical composition and replacement of cations in sites A and/or B. In this paper, LaFe1-xMnxO3 (0 ≤ x ≤ 1) orthoferrites-type was prepared by Pechini method and Microwave-assisted combustion reaction in order to evaluate the influence of synthesis route on the formation of oxide, as well as the effect of parcial replacement of iron by manganese and heat treatment on the magnetic properties. The precursor powders were calcined at 700°C, 900°C, 1100°C and 1300°C for 4 hours and they were characterized by the techniques: Thermogravimetric analysis (TGA), X ray diffraction (XRD), Refinement by Rietveld method, Scanning electron microscopy (SEM), Reduction temperature programmed (RTP) and Magnetic hysteresis measurements performed at room temperature. According to the XRD patterns, the formation of perovskite phase with orthorhombic structure was observed for the systems where 0 ≤ x ≤ 0.5 and rhombohedral for x = 1. The results also showed a decrease of lattice parameters with the parcial replacement of iron by manganese and consequently a reduction in cell volume. The hysteresis curves exhibited weak ferromagnetism for the systems prepared by both synthesis methods. However, a dependence of magnetization as a function of dopant content was observed for samples produced by Pechini method. As for the systems prepared by combustion reaction, it was found that the secondary phases exert a strong influence on the magnetic behavior

Parcelamento da adubação e da fertirrigação na produção de palmito pupunha no Noroeste Paulista

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Bifurcation of limit cycles from an n-dimensional linear center inside a class of piecewise linear differential systems

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Evaluation of figs mutant selections cv. roxo-de-Valinhos

The fig (Ficus carica L.), belonging to the Moraceas family, is one of the most important fruit crops, bringing Brazil to the condition of the tenth largest fig producer and exporter in the world. But the culture presents some problems with plant protection, and in Brazil, it is all implanted with an only cultivar, Roxo-de-Valinhos, which produces seedless fruit, not permitting the conventional improvement. In this sense, the genetic improvement by using mutagenic becomes a very important research line, that can greatly contribute to the culture development. Considering this, this study aimed to evaluate selections of fig originated from mutant plants formed by cuttings from buds irradiated with gamma ray and compare them with the main varieties of the culture in commercial plantation. By using plants originated from 5 traditional fig cultivars cuttings and 5 fig mutant selections (formed by cuttings from Roxo-de-Valinhos buds irradiated with gamma ray, in the dose of 30 Gy), spaced by 2.5 x 1.5 m. The experimental layout was a completely randomized block design, with 10 treatments, 3 repetitions and 5 plants per plot. The evaluations are made from the plants vegetative growth as well as the fruit characteristics. Through data analysis, it seems that there is variability between the mutant selections and with the traditional cultivars, and the treatment PI-189 was superior to the standard cultivar Roxo-de-Valinhos on great commercial characteristics importance, such as "number of fruit per plant", "average weight per fruit" and "productivity", having the same traits, showing itself with enormous potential for future studies.

Seleção de clones de figueira cv. roxo de Valinhos formados por gemas irradiadas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação de seleções mutantes de figueira cv. Roxo-de-Valinhos

A figueira (Ficus carica L.), pertencente à família das Moráceas, constitui-se numa das mais importantes frutíferas cultivadas, elevando o Brasil à condição de décimo maior produtor e exportador de figos do mundo. Porém, a ficicultura apresenta alguns problemas fitossanitários, além de, no Brasil, estar toda implantada com uma única cultivar, a Roxo-de-Valinhos, que produz frutos sem sementes, inviabilizando o melhoramento convencional. Nesse sentido, o melhoramento genético, com o uso de mutagênicos, passa a ser uma linha de pesquisa altamente importante, podendo contribuir enormemente para o desenvolvimento da cultura. Diante disto, o objetivo do presente trabalho foi avaliar seleções mutantes de figueira originadas de plantas formadas por estacas provenientes de gemas irradiadas com raio gama, bem como compará-las com as principais cultivares da cultura em plantio comercial. Utilizou-se de plantas originadas de estacas de 5 cultivares tradicionais de figueira e de cinco seleções de figueiras mutantes (formadas por estacas originadas de gemas da cultivar Roxo-de-Valinhos irradiadas com raio gama, na dose de 30 Gy), cultivadas em espaçamento de 2,5 x 1,5 m. O delineamento experimental utilizado foi o de blocos inteiramente casualizados, contendo 10 tratamentos, com 3 repetições e 5 plantas por parcela. As avaliações foram realizadas a partir do desenvolvimento vegetativo das plantas, bem como as características dos frutos. da análise dos dados, conclui-se que há variabilidade entre as seleções mutantes e destas com as cultivares tradicionais, e que o tratamento PI-189 foi superior à cultivar-padrão Roxo-de-Valinhos em características de grande importância comercial, como número de frutos por planta, massa média por fruto e produtividade, igualando-se nas demais características, mostrando-se, assim, com enorme potencial para posteriores estudos.

Estudo prospectivo observacional sobre a incidência de injúria renal aguda em unidade de terapia intensiva de um hospital universitário

OBJETIVO: Analisar comparativamente características clínicas e evolução de pacientes com e sem IRA adquirida em UTI geral de um hospital universitário terciário. MÉTODO: Estudo prospectivo observacional com 263 pacientes acompanhados diariamente durante a internação em UTI Geral do Hospital das Clínicas da Faculdade de Medicina de Botucatu no período de julho de 2007 a abril de 2008. RESULTADOS: A incidência de IRA foi de 31,2%. Os grupos foram semelhantes quanto ao sexo e diferiram quanto à etiologia da admissão em UTI (sepse: 31,7% x 13,1%, p < 0,0001, pós-operatório: 11% x 43%, p < 0,0001), idade (59,6 ± 18,1 x 50,2 ± 18,6 anos, p < 0,0001), APACHE II: (21 ± 11,1 x 11 ± 4,8, p = 0,002), oligúria (67,7% x 4,5%, p < 0,0001), presença de ventilação mecânica (81,7 x 57,7%, p = 0,0014), uso de drogas vasoativas (62,2 x 32,6%, p < 0,0001) e enfermaria de procedência (PS: 22 x 14,5%, p = 0,02 e centro cirúrgico: 42,7 x 62,6%, p = 0,03). Quanto às comorbidades, os grupos foram diferentes quanto à presença de HAS e IRC (42,6 x 35,9%, p = 0,005 e 15,8 x 2,1%, p = 0,04, respectivamente) e semelhantes quanto à presença de diabetes e ICC (19,5 x 11%, ns e 6 x 1,1%, ns, respectivamente). A mortalidade foi superior nos pacientes que contraíram IRA (62,1 x 16,5%, p < 0,0001). CONCLUSÃO: A incidência de IRA é elevada em UTI e presente em pacientes com parâmetros clínicos e índices prognósticos de maior gravidade, o que justifica a maior mortalidade observada neles.

On Fuzzy Implication Classes - Towards Extensions of Fuzzy Rule-Based Systems

Atualmente, há diferentes definições de implicações fuzzy aceitas na literatura. Do ponto de vista teórico, esta falta de consenso demonstra que há discordâncias sobre o real significado de "implicação lógica" nos contextos Booleano e fuzzy. Do ponto de vista prático, isso gera dúvidas a respeito de quais "operadores de implicação" os engenheiros de software devem considerar para implementar um Sistema Baseado em Regras Fuzzy (SBRF). Uma escolha ruim destes operadores pode implicar em SBRF's com menor acurácia e menos apropriados aos seus domínios de aplicação. Uma forma de contornar esta situação e conhecer melhor os conectivos lógicos fuzzy. Para isso se faz necessário saber quais propriedades tais conectivos podem satisfazer. Portanto, a m de corroborar com o significado de implicação fuzzy e corroborar com a implementação de SBRF's mais apropriados, várias leis Booleanas têm sido generalizadas e estudadas como equações ou inequações nas lógicas fuzzy. Tais generalizações são chamadas de leis Boolean-like e elas não são comumente válidas em qualquer semântica fuzzy. Neste cenário, esta dissertação apresenta uma investigação sobre as condições suficientes e necessárias nas quais três leis Booleanlike like — y ≤ I(x, y), I(x, I(y, x)) = 1 e I(x, I(y, z)) = I(I(x, y), I(x, z)) — se mantém válidas no contexto fuzzy, considerando seis classes de implicações fuzzy e implicações geradas por automorfismos. Além disso, ainda no intuito de implementar SBRF's mais apropriados, propomos uma extensão para os mesmos

Proposta metodológica para o imageamento digital e modelagem virtual 3d de um bloco de rochas travertinas

In this paper we present the methodological procedures involved in the digital imaging in mesoscale of a block of travertines rock of quaternary age, originating from the city of Acquasanta, located in the Apennines, Italy. This rocky block, called T-Block, was stored in the courtyard of the Laboratório Experimental Petróleo "Kelsen Valente" (LabPetro), of Universidade Estadual de Campinas (UNICAMP), so that from it were performed Scientific studies, mainly for research groups universities and research centers working in brazilian areas of reservoir characterization and 3D digital imaging. The purpose of this work is the development of a Model Solid Digital, from the use of non-invasive techniques of digital 3D imaging of internal and external surfaces of the T-Block. For the imaging of the external surfaces technology has been used LIDAR (Light Detection and Range) and the imaging surface Interior was done using Ground Penetrating Radar (GPR), moreover, profiles were obtained with a Gamma Ray Gamae-spectômetro laptop. The goal of 3D digital imaging involved the identification and parameterization of surface geological and sedimentary facies that could represent heterogeneities depositional mesoscale, based on study of a block rocky with dimensions of approximately 1.60 m x 1.60 m x 2.70 m. The data acquired by means of terrestrial laser scanner made available georeferenced spatial information of the surface of the block (X, Y, Z), and varying the intensity values of the return laser beam and high resolution RGB data (3 mm x 3 mm), total points acquired 28,505,106. This information was used as an aid in the interpretation of radargrams and are ready to be displayed in rooms virtual reality. With the GPR was obtained 15 profiles of 2.3 m and 2 3D grids, each with 24 sections horizontal of 1.3 and 14 m vertical sections of 2.3 m, both the Antenna 900 MHz to about 2600 MHz antenna. Finally, the use of GPR associated with Laser Scanner enabled the identification and 3D mapping of 3 different radarfácies which were correlated with three sedimentary facies as had been defined at the outset. The 6 profiles showed gamma a low amplitude variation in the values of radioactivity. This is likely due to the fact of the sedimentary layers profiled have the same mineralogical composition, being composed by carbonate sediments, with no clay in siliciclastic pellitic layers or other mineral carrier elements radioactive

Potential effects of the herbicide Diuron on mammary and urinary bladder two-stage carcinogenesis in a female Swiss mouse model

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Inclusão do ovo desidratado em rações peletizadas ou fareladas para frangos de corte

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Periodontal tissue response to coverage of root cavities restored with resin materials: A histomorphometric study in dogs

Background: the purpose of this study was to histomorphometrically evaluate the response of periodontal tissues covering Class V resin restorations in dogs.Methods: After raising a mucoperiosteal flap, bony defects measuring 5 x 5 mm were created on the buccal aspect of the canines of five dogs followed by cavity preparations on the root surface measuring 3 x 3 x 1 mm. Before repositioning the flap to cover the bone defect, the cavities were restored with composite resin (CR) or resin-modified glass ionomer cement (RMGIC) or were left unrestored as control (C). The dogs were euthanized 90 days after surgery. Specimens comprising the tooth and periodontal tissues were removed, processed routinely, cut into longitudinal serial sections in the bucco-lingual direction, and stained with hematoxylin and eosin (H&E) or Masson's trichrome. The most central sections were selected for histomorphometric analysis.Results: Histomorphometric analysis revealed apical migration of epithelial tissue onto the restorative materials (RMGIC and CR). The C group presented significantly longer connective tissue attachment (P < 0.05) than the RMGIC and CR groups and significantly higher bone regeneration (P < 0.05) compared to the RMGIC group. Histologically, the cervical third (CT) of all groups had the most marked chronic inflammatory infiltrate.Conclusions: Within the limits of this study, it can be concluded that the restorative materials used exhibit biocompatibility; however, both materials interfered with the development of new bone and the connective tissue attachment process.

COLOR STABILITY of SEALED COMPOSITE RESIN RESTORATIVE MATERIALS AFTER ULTRAVIOLET ARTIFICIAL AGING and IMMERSION IN STAINING SOLUTIONS

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Changes in the stiffness of demineralized dentin following application of tooth whitening agents

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of prolonged erosive pH cycling on different restorative materials

This in vitro study evaluated the effect of a prolonged erosive pH cycling on the superficial microhardness change (SMHC) and the erosive wear of different restorative materials. Eighty enamel specimens with prepared cavities of 1.5 x 1.5 mm were randomly divided into eight groups according to the restorative materials used for the fillings (RMGI - resin-modified glass-ionomer, CGI - conventional glass-ionomer, CR- composite resin, A - amalgam) and immersion media used (ERO - erosive medium or SAL - artificial saliva). During 35 days, half of the specimens were immersed in a cola drink (ERO), for 5 min, three times a day, and they remained in SAL between the erosive cycles. The other half of the specimens was immersed in SAL only, for the entire experimental period (control). Data were tested for significant differences by anova and Tukey's tests (P < 0.05). Scanning electron microscopy images were made to illustrate the enamel erosive wear and restorative materials alterations. The mean SMHC (%) and mean erosive wear (mu m) of the materials were: RMGI-ERO (30/0.5); CGI-ERO (37/0.5); CR-ERO (-0.3/0.3); A-ERO (-4/0.3); RMGI-SAL (4/0.4); CGI-SAL (-6/0.4); CR-SAL (-3/0.2) and A-SAL (2/0.4). Scanning electron microscopy images showed pronounced enamel erosive wear on groups submitted to erosive pH cycling when compared with groups maintained in saliva. In conclusion, the prolonged pH cycling promoted significantly higher alterations (SMHC and erosive wear) on the glass-ionomer cements than the CR and amalgam.