A novel approach to increasing inventory with the current panel: Increasing donation frequency by asking for a different blood product

BACKGROUND Ongoing shortages of blood products may be addressed through additional donations. However, donation frequency rates are typically lower than medically possible. This preliminary study aims to determine voluntary nonremunerated whole blood (WB) and plasmapheresis donors' willingness, and subsequent facilitators and barriers, to make additional donations of a different type. STUDY DESIGN AND METHODS Forty individual telephone interviews were conducted posing two additional donation pattern scenarios: first, making a single and, second, making multiple plasmapheresis donations between WB donations. Stratified purposive sampling was conducted for four samples varying in donation experience: no-plasma, new-to-both-WB-and-plasma, new-to-plasma, and plasma donors. Interviews were analyzed yielding excellent (κ values > 0.81) inter-rater reliability. RESULTS Facilitators were more endorsed than barriers for a single but not multiple plasmapheresis donation. More new-to-both donors (n = 5) were willing to make multiple plasma donations between WB donations than others (n = 1 each) and identified fewer barriers (n = 3) than those more experienced in donation (n = 8 no plasma, n = 10 new to both, n = 11 plasma). Donors in the plasma sample were concerned about the subsequent reduced time between plasma donations by adding WB donations (n = 3). The no-plasma and new-to-plasma donors were concerned about the time commitment required (n = 3). CONCLUSION Current donors are willing to add different product donations but donation history influences their willingness to change. Early introduction of multiple donation types, variation in inventory levels, and addressing barriers will provide blood collection agencies with a novel and cost-effective inventory management strategy.

Commuting mode choice in transit oriented development: Disentangling the effects of competitive neighbourhoods, travel attitudes, and self-selection

This research identifies the commuting mode choice behaviour of 3537 adults living in different types of transit oriented development (TOD) in Brisbane by disentangling the effects of their “evil twin” transit adjacent developments (TADs), and by also controlling for residential self-selection, travel attitudes and preferences, and socio-demographic effects. A TwoStep cluster analysis was conducted to identify the natural groupings of respondents’ living environment based on six built environment indicators. The analysis resulted in five types of neighbourhoods: urban TODs, activity centre TODs, potential TODs, TADs, and traditional suburbs. HABITAT survey data were used to derive the commute mode choice behaviour of people living in these neighbourhoods. In addition, statements reflecting both respondents’ travel attitudes and living preferences were also collected as part of the survey. Factor analyses were conducted based on these statements and these derived factors were then used to control for residential self-selection. Four binary logistic regression models were estimated, one for each of the travel modes used (e.g. public transport, active transport, less sustainable transport such as the car/taxi, and other), to differentiate between the commuting behaviour of people living in the five types of neighbourhoods. The findings verify that urban TODs enhance the use of public transport and reduce car usage. No significant difference was found in the commuting behaviour between respondents living in traditional suburbs and TADs. The results confirm the hypothesis that TADs are the “evil twin” of TODs. The data indicates that TADs and the mode choices of residents in these neighbourhoods is a missed transport policy opportunity. Further policy efforts are required for a successive transition of TADs into TODs in order to realise the full benefits of these. TOD policy should also be integrated with context specific TOD design principles.

IdeaWall: Mixed mode distributed collaboration in enterprise environments

In early stages of design and modeling, computers and computer applications are often considered an obstacle, rather than a facilitator of the process. Most notably, brainstorms, process modeling with business experts, or development planning, are often performed by a team in front of a whiteboard. While "whiteboarding" is recognized as an effective tool, low-tech solutions that allow remote participants to contribute are still not generally available. This is a striking observation, considering that vast majority of teams in large organizations are distributed teams. And this has also been one of the key triggers behind the project described in this article, where a team of corporate researchers decided to identify state of the art technologies that could facilitate the scenario mentioned above. This paper is an account of a research project in the area of enterprise collaboration, with a strong focus on the aspects of human computer interaction in mixed mode environments, especially in areas of collaboration where computers still play a secondary role. It is describing a currently running corporate research project. © 2012 Springer-Verlag.

Facilitating sustainable professional part-time work: A question of design?

Despite significant socio-demographic and economic shifts in the contours of work over the past 40 years, there has been surprisingly little change in the way work is designed. Current understandings of the content and structure of jobs are predominantly underpinned by early 20th century theories derived from the manufacturing industry where employees worked independently of each other in stand-alone organisations. It is only in the last 10 years that elaborations and extensions to job/work design theory have been posed, which accommodate some of the fundamental shifts in contemporary work settings, yet these extended frameworks have received little empirical attention. Utilising contemporary features of work design and a sample of professional service workers, the purpose of this study is to examine to what extent and how part-time roles are designed relative to equivalent full-time roles. The findings contribute to efforts to design effective part-time roles that balance organisational and individual objectives.

Fire design rules for load bearing cold-formed steel frame walls exposed to realistic design fire curves

Light gauge Steel Frame (LSF) walls are extensively used in the building industry due to the many advantages they provide over other wall systems. Although LSF walls have been used widely, fire design of LSF walls is based on approximate prescriptive methods based on limited fire tests. Also these fire tests were conducted using the standard fire curve [1] and the applicability of available design rules to realistic design fire curves has not been verified. This paper investigates the accuracy of existing fire design rules in the current cold-formed steel standards and the modifications proposed by previous researchers. Of these the recently developed design rules by Gunalan and Mahendran [2] based on Eurocode 3 Part 1.3 [3] and AS/NZS 4600 [4] for standard fire exposure [1] were investigated in detail to determine their applicability to predict the axial compression strengths and fire resistance ratings of LSF walls exposed to realistic design fire curves. This paper also presents the fire performance results of LSF walls exposed to a range of realistic fire curves obtained using a finite element analysis based parametric study. The results from the parametric study were used to develop a simplified design method based on the critical hot flange temperature to predict the fire resistance ratings of LSF walls exposed to realistic fire curves. Finally, the stud failure times (fire resistance rating) obtained from the fire design rules and the simplified design method were compared with parametric study results for LSF walls lined with single and double plasterboards, and externally insulated with rock fibres under realistic fire curves.

Design and fabrication of linear pixel arrays for organic photovoltaic modules to achieve scalable power output

We describe a design and fabrication method to enable simpler manufacturing of more efficient organic solar cell modules using a modified flat panel deposition technique. Many mini-cell pixels are individually connected to each other in parallel forming a macro-scale solar cell array. The pixel size of each array is optimized through experimentation to maximize the efficiency of the whole array. We demonstrate that integrated organic solar cell modules with a scalable current output can be fabricated in this fashion and can also be connected in series to generate a scalable voltage output.

Enhancing current density using vertically oriented organic photovoltaics

We report a new organic photovoltaics (OPV) design, a wrapped OPV, which can circumvent both challenges of short exciton diffusion length [1], and low charge carrier mobility [2] of organic semiconductors by orienting the OPV vertically, to capture; manage; guide and use all incident photons and therefore, generate higher current. Resonant light, on being transmitted into a wrapped OPV, makes multiple passes through the photoactive layer and is absorbed completely, thus achieving benefits of thick photoactive layer while maintaining its ultra-thin thickness requirement. The current density generated from a wrapped OPV is twice than that generated by a similar OPV with flat orientation.

Design guidance for blast-resistant glazing

This paper reviews current design standards and test methods for blast-resistant glazing design and compares a typical design outcome with that from comprehensive finite-element (FE) analysis. Design standards are conservative and are limited to the design of relatively small glazed panels. Standard test methods are expensive, create environmental pollution, and can classify the hazard ratings of only smaller glazed panels. Here the design of a laminated glass (LG) panel is carried out according to an existing design standard, and then its performance is examined using comprehensive FE modeling and analysis. Finite-element results indicate that both glass panes crack, the interlayer yields with little damage, and the sealant joints do not fail for the designed blast load. This failure pattern satisfies some of the requirements for minimal hazard rating in the design standard. It is evident that interlayer thickness and material properties are important during the post-crack stage of an LG panel, but they are not accounted for in the design standards. The new information generated in this paper will contribute toward an enhanced blast design of LG panels.

Development of a new design expression for the in-plane shear capacity of the partially grouted concrete masonry walls

Partially grouted masonry walls subjected to in-plane shear exhibit a complex behaviour because of the influence of the aspect ratio, the pre-compression, the grouting pattern, the ratios of the horizontal and the vertical reinforcements, the boundary conditions and the characteristics of the constituent materials. The existing in-plane shear expressions for the partially grouted masonry are formulated as sum of strength of three parameters, namely, the masonry, the reinforcement and the axial force. The parameter ‘masonry’ includes the wall aspect ratio and the masonry compressive strength; the aspect ratio of the unreinforced panel inscribed into the grouted cores and bond beams are not considered, although failure is often dominated by these unreinforced masonry panels. This paper describes the dominance of these panels, particularly those that are squat, to the shear capacity of whole of shear walls. Further, the current design formulae are shown highly un-conservative by many researchers; this paper provides a potential reason for this un-conservativeness. It is shown that by including an additional term of the unreinforced panel aspect ratio a rational design formula could be established. This new expression is validated with independent test results reported in the literature – both Australian and overseas; the predictions are shown to be conservative.

‘Blind Faith’. An experiment with narrative agency in game design

This paper reports on the current field of narrative-based game design through case study analysis with a particular focus on balancing high narrative agency with low production resources.

The design and implementation of an Information Accountability Framework for eHealth systems

This tutorial primarily focuses on the implementation of Information Accountability (IA) protocols defined in an Information Accountability Framework (IAF) in eHealth systems. Concerns over the security and privacy of patient information are one of the biggest hindrances to sharing health information and the wide adoption of eHealth systems. At present, there are competing requirements between healthcare consumers' (i.e. patients) requirements and healthcare professionals' (HCP) requirements. While consumers want control over their information, healthcare professionals want access to as much information as required in order to make well-informed decisions and provide quality care. This conflict is evident in the review of Australia's PCEHR system and in recent studies of patient control of access to their eHealth information. In order to balance these requirements, the use of an Information Accountability Framework devised for eHealth systems has been proposed. Through the use of IA protocols, so-called Accountable-eHealth systems (AeH) create an eHealth environment where health information is available to the right person at the right time without rigid barriers whilst empowering the consumers with information control and transparency. In this half-day tutorial, we will discuss and describe the technical challenges surrounding the implementation of the IAF protocols into existing eHealth systems and demonstrate their use. The functionality of the protocols and AeH systems will be demonstrated, and an example of the implementation of the IAF protocols into an existing eHealth system will be presented and discussed.

Design of redox/radical sensing molecules via Nitrile Imine-Mediated Tetrazole-ene Cycloaddition (NITEC)

The current study introduces a novel synthetic avenue for the preparation of profluorescent nitroxides via nitrile imine-mediated tetrazole-ene cycloaddition (NITEC). The photoinduced cycloaddition was performed under metal-free, mild conditions allowing the preparation of a library of the nitroxide functionalized pyrazolines and corresponding methoxyamines. High reaction rates and full conversion were observed, with the presence of the nitroxide having no significant impact on the cycloaddition performance. The formed products were investigated with respect to their photophysical properties in order to quantify their “switch on/off” behavior. The fluorescence quenching performance is strongly dependent on the distance between the chromophore and the free radical spin as demonstrated theoretically and experimentally. Highest levels of fluorescence quenching were achieved for pyrazolines with the nitroxide directly fused to the chromophore. Importantly, the pyrazoline profluorescent nitroxides were shown to efficiently act as sensors for redox/radical processes.

Enriching architectural design education through interactive displays and local community engagement

Designers have a social responsibility to deal with the needs, issues, and problems that their clients and communities are confronted with. Students of design require opportunities to reflect on their role as social facilitators to develop an attitude towards community engagement through different phases and aspects of their careers. However, current design courses are challenged by compressed timeframes and fragmented scenarios of different academic requirements that do not actively teach community engagement. This paper outlines a participatory and technological approach that was employed to address these issues within the teaching of Architecture and Urban Design at the Queensland University of Technology, Brisbane, Australia. A multi-phase community based research project with actual stakeholders was implemented over a two-year period. Approximately 150 students in the final year of the Bachelor of Design-Architecture; 10 students in the Master of Architecture and 15 students in the Master of Design-Urban Design have informed and influenced each others’ learning through the teaching and research nexus facilitated by this project. The technical approach was implemented in form of a bespoke digital platform that supported the display and discussion of digital media on a series of interactive touch walls. The platform allowed students to easily upload their final designs onto large interactive surfaces, where visitors could explore the media and provide comments. Through the use of this technical platform and the introduction of neogeography, students have been able to broaden their level of interaction and support their learning experience through external structured and unstructured feedback from the local community. Students have not only been exposed to community representatives, but they also have been working in parallel on a specific case study providing each other, across different years and courses, material for reflection and data to structure their design activities.

Advanced tissue engineering scaffold design for regeneration of the complex hierarchical periodontal structure

AIM: This study investigated the ability of an osteoconductive biphasic scaffold to simultaneously regenerate alveolar bone, periodontal ligament and cementum. MATERIALS AND METHODS: A biphasic scaffold was built by attaching a fused deposition modelled bone compartment to a melt electrospun periodontal compartment. The bone compartment was coated with a calcium phosphate (CaP) layer for increasing osteoconductivity, seeded with osteoblasts and cultured in vitro for 6 weeks. The resulting constructs were then complemented with the placement of PDL cell sheets on the periodontal compartment, attached to a dentin block and subcutaneously implanted into athymic rats for 8 weeks. Scanning electron microscopy, X-ray diffraction, alkaline phosphatase and DNA content quantification, confocal laser microscopy, micro computerized tomography and histological analysis were employed to evaluate the scaffold's performance. RESULTS: The in vitro study showed that alkaline phosphatase activity was significantly increased in the CaP-coated samples and they also displayed enhanced mineralization. In the in vivo study, significantly more bone formation was observed in the coated scaffolds. Histological analysis revealed that the large pore size of the periodontal compartment permitted vascularization of the cell sheets, and periodontal attachment was achieved at the dentin interface. CONCLUSIONS: This work demonstrates that the combination of cell sheet technology together with an osteoconductive biphasic scaffold could be utilized to address the limitations of current periodontal regeneration techniques.

Design and flight testing of an integrated solar powered UAV and WSN for greenhouse gas monitoring emissions in agricultural farms

There is an increased interest in measuring the amount of greenhouse gases produced by farming practices . This paper describes an integrated solar powered Unmanned Air Vehicles (UAV) and Wireless Sensor Network (WSN) gas sensing system for greenhouse gas emissions in agricultural lands. The system uses a generic gas sensing system for CH4 and CO2 concentrations using metal oxide (MoX) and non-dispersive infrared sensors, and a new solar cell encapsulation method to power the unmanned aerial system (UAS)as well as a data management platform to store, analyze and share the information with operators and external users. The system was successfully field tested at ground and low altitudes, collecting, storing and transmitting data in real time to a central node for analysis and 3D mapping. The system can be used in a wide range of outdoor applications at a relatively low operational cost. In particular, agricultural environments are increasingly subject to emissions mitigation policies. Accurate measurements of CH4 and CO2 with its temporal and spatial variability can provide farm managers key information to plan agricultural practices. A video of the bench and flight test performed can be seen in the following link: https://www.youtube.com/watch?v=Bwas7stYIxQ