Geology of the NW Indian Himalaya

This review paper deals with the geology of the NW Indian Himalaya situated in the states of Jammu and Kashmir, Himachal Pradesh and Garhwal. The models and mechanisms discussed, concerning the tectonic and metamorphic history of the Himalayan range, are based on a new compilation of a geological map and cross sections, as well as on paleomagnetic, stratigraphic, petrologic, structural, metamorphic, thermobarometric and radiometric data. The protolith of the Himalayan range, the North Indian flexural passive margin of the Neo-Tethys ocean, consists of a Lower Proterozoic basement, intruded by 1.8-1.9 Ga bimodal magmatites, overlain by a horizontally stratified sequence of Upper Proterozoic to Paleocene sediments, intruded by 470-500 Ma old Ordovician mainly peraluminous s-type granites, Carboniferous tholeiitic to alkaline basalts and intruded and overlain by Permian tholeiitic continental flood basalts. No elements of the Archaen crystalline basement of the South Indian shield have been identified in the Himalayan range. Deformation of the Himalayan accretionary wedge resulted from the continental collision of India and Asia beginning some 65-55 Ma ago, after the NE-directed underthrusting of the Neo-Tethys oceanic crust below Asia and the formation of the Andean-type 103-50 (-41) Ma old Ladakh batholith to the north of the Indus Suture. Cylindrical in geometry, the Himalayan range consists, from NE to SW, from older to younger tectonic elements, of the following zones: 1) The 25 km wide Ladakh batholith and the Asian mantle wedge form the backstop of the growing Himalayan accretionary wedge. 2) The Indus Suture zone is composed of obducted slices of the oceanic crust, island arcs, like the Dras arc, overlain by Late Cretaceous fore arc basin sediments and the mainly Paleocene to Early Eocene and Miocene epi-sutural intra-continental Indus molasse. 3) The Late Paleocene to Eocene North Himalayan nappe stack, up to 40 km thick prior to erosion, consists of Upper Proterozoic to Paleocene rocks, with the eclogitic and coesite bearing Tso Morari gneiss nappe at its base. It includes a branch of the Central Himalayan detachment, the 22-18 Ma old Zanskar Shear zone that is intruded and dated by the 22 Ma Gumburanjun leucogranite; it reactivates the frontal thrusts of the SW-verging North Himalayan nappes. 4) The late Eocene-Miocene SW-directed High Himalayan or ``Crystalline'' nappe comprises Upper Proterozoic to Mesozoic sediments and Ordovician granites, identical to those of the North Himalayan nappes. The Main Central thrust at its base was created in a zone of Eocene to Early Oligocene anatexis by ductile detachment of the subducted Indian crust, below the pre-existing 25-35 km thick NE-directed Shikar Beh and SW-directed North Himalayan nappe stacks. 5) The late Miocene Lesser Himalayan thrust with the Main Boundary Thrust at its base consists of early Proterozoic to Cambrian rocks intruded by 1.8-1.9 Ga bimodal magmatites. The Subhimalaya is a thrust wedge of Himalayan fore deep basin sediments, composed of the Early Eocene marine Subathu marls and sandstones as well as the up to 8'000 m-thick Miocene to recent Ganga molasse, a coarsening upwards sequence of shales, sandstones and conglomerates. The active frontal thrust is covered by the sediments of the Indus-Ganga plains.

Plate tectonics of the Altaids

Abstract: The Altaids consist in a huge accretionary-type belt extending from Siberia through Mon-golia, northern China, Kyrgyzstan and Kazakhstan. They were formed from the Vendian through the Jurassic by the accretion of numerous displaced and exotic terranes (e.g. island arc, ribbon microcontinent, seamount, basaltic plateau, back-arc basin). The number, nature and origin of the terranes differ according to the palaeotectonic models of the different authors. Thanks to a geo- dynamic study (i.e. definition of tectonic settings and elaboration of geodynamic scenarios) and plate tectonics modelling, this work aims to present an alternative model explaining the Palaeozoic palaeotectonic evolution of the Altaids. Based on a large set of compiled geological data related to palaeogeography and geodyna¬mic (e.g. sedimentology, stratigraphy, palaeobiogeography, palaeomagnetism, magmatism, me- tamorphism, tectonic...), a partly new classification of the terranes and sutures implicated in the formation of the Altaids is proposed. In the aim to elaborate plate tectonics reconstructions, it is necessary to fragment the present arrangement of continents into consistent geological units. To avoid confusion with existing terminology (e.g. tectonic units, tectono-stratigraphic units, micro- continents, terranes, blocks...), the new concept of "Geodynamic Units (GDU)" was introduced. A terrane may be formed by a set of GDUs. It consists of a continental and/or oceanic fragment which has its own kinematic and geodynamic evolution for a given period. With the same ap-proach, the life span and type of the disappeared oceans is inferred thanks to the study of the mate-rial contained in suture zones. The interpretation of the tectonic settings within the GDUs comple-ted by the restoration of oceans leads to the elaboration of geodynamic scenarios. Since the Wilson cycle was presented in 1967, numerous works demonstrated that the continental growth is more complex and results from diverse geodynamic scenarios. The identification of these scenarios and their exploitation enable to elaborate plate tectonics models. The models are self-constraining (i.e. space and time constraints) and contest or confirm in turn the geodynamic scenarios which were initially proposed. The Altaids can be divided into three domains: (1) the Peri-Siberian, (2) the Kazakhstan, and (3) the Tarim-North China domains. The Peri-Siberian Domain consists of displaced (i.e. Sayan Terrane Tuva-Mongolian, Lake-Khamsara Terrane) and exotic terranes (i.e. Altai-Mongolian and Khangai-Argunsky Terrane) accreted to Siberia from the Vendian through the Ordovician. Fol-lowing the accretion of these terranes, the newly formed Siberia active margin remained active un-til its part collision with the Kazakhstan Superterrane in the Carboniferous. The eastern part of the active margin (i.e. East Mongolia) continued to act until the Permian when the North-China Tarim Superterrane collided with it. The geodynamic evolution of the eastern part of the Peri-Siberian Domain (i.e. Eastern Mongolia and Siberia) is complicated by the opening of the Mongol-Okhotsk Ocean in the Silurian. The Kazakhstan Domain is composed of several continental terranes of East Gondwana origin amalgamated together during the Ordovician-Silurian time. After these different orogenic events, the Kazakhstan Superterrane evolved as a single superterrane until its collision with a Tarim-North China related-terrane (i.e. Tianshan-Hanshan Terrane) and Siberian Continent during the Devonian. This new organisation of the continents imply a continued active margin from Siberia, to North China through the Kazakhstan Superterrane and the closure of the Junggar- Balkash Ocean which implied the oroclinal bending of the Kazakhstan Superterrane during the entire Carboniferous. The formation history of the Tarim-North China Domain is less complex. The Cambrian northern passive margin became active in the Ordovician. In the Silurian, the South Tianshan back-arc Ocean was open and led to the formation of the Tianshan-Hanshan Terrane which collided with the Kazakhstan Superterrane during the Devonian. The collision between Siberia and the eastern part of the Tarim-North China continents (i.e. Inner Mongolia), implied by the closure of the Solonker Ocean, took place in the Permian. Since this time, the major part of the Altaids was formed, the Mongol-Okhotsk Ocean only was still open and closed during the Jurassic. Résumé: La chaîne des Altaïdes est une importante chaîne d'accrétion qui s'étend en Sibérie, Mon-golie, Chine du Nord, Kirghizstan et Kazakhstan. Elle s'est formée durant la période du Vendian au Jurassique par l'accrétion de nombreux terranes déplacés ou exotiques (par exemple arc océa-nique, microcontinent, guyot, plateau basaltique, basin d'arrière-arc...). Le nombre, la nature ou encore l'origine diffèrent selon les modèles paléo-tectoniques proposés par les différents auteurs. Grâce à une étude géodynamique (c'est-à-dire définition des environnements tectoniques et éla-boration de scénarios géodynamiques) et à la modélisation de la tectonique des plaques, ce travail propose un modèle alternatif expliquant l'évolution paléo-tectonique des Altaïdes. Basé sur une large compilation de données géologiques pertinentes en termes de paléo-géographie et de géodynamique (par exemple sédimentologie, stratigraphie, paléo-biogéographie, paléomagnétisme, magmatisme, métamorphisme, tectonique...), une nouvelle classification des terranes et des sutures impliqués dans la formation des Altaïdes est proposée. Dans le but d'élabo¬rer des reconstructions de plaques tectoniques, il est nécessaire de fragmenter l'arrangement actuel des continents en unités tectoniques cohérentes. Afin d'éviter les confusions avec la terminolo¬gie existante (par exemple unité tectonique, unité tectono-stratigraphique, microcontinent, block, terrane...), le nouveau concept d' "Unité Géodynamique (UGD)" a été introduit. Un terrane est formé d'une ou plusieurs UGD et représente un fragment océanique ou continental défini pas sa propre cinétique et évolution géodynamique pour une période donnée. Parallèlement, la durée de vie et le type des océans disparus (c'est-à-dire principal ou secondaire) est déduite grâce à l'étude du matériel contenu dans les zones de sutures. L'interprétation des environnements tectoniques des UGD associés à la restauration des océans mène à l'élaboration de scénarios géodynamiques. Depuis que le Cycle de Wilson a été présenté en 1967, de nombreux travaux ont démontré que la croissance continentale peut résulter de divers scénarios géodynamiques. L'identification et l'ex-ploitation de ces scénarios permet finalement l'élaboration de modèles de tectonique des plaques. Les modèles sont auto-contraignants (c'est-à-dire contraintes spatiales et temporelles) et peuvent soit contester ou confirmer les scénarios géodynamiques initialement proposés. Les Altaïdes peuvent être divisées en trois domaines : (1) le Domaine Péri-Sibérien, (2) le Domaine Kazakh, et (3) le Domaine Tarim-Nord Chinois. Le Domaine Péri-Sibérien est composé de terranes déplacés (c'est-à-dire Terrane du Sayan, Tuva-Mongol et Lake-Khamsara) et exotiques (c'est-à-dire Terrane Altai-Mongol et Khangai-Argunsky) qui ont été accrétés au craton Sibérien durant la période du Vendien à l'Ordovicien. Suite à l'accrétion de ces terranes, la marge sud-est de la Sibérie nouvellement formée reste active jusqu'à sa collision partielle avec le Superterrane Ka-zakh au Carbonifère. La partie est de la marge active (c'est-à-dire Mongolie de l'est) continue son activité jusqu'au Permien lors de sa collision avec le Superterrane Tarim-Nord Chinois. L'évolu¬tion géodynamique de la partie est du Domaine Sibérien est compliquée par l'ouverture Silurienne de l'Océan Mongol-Okhotsk qui disparaîtra seulement au Jurassique. Le Domaine Kazakh est composé de plusieurs terranes d'origine est-Gondwanienne accrétés les uns avec les autres avant ou pendant le Silurien inférieur et leurs evolution successive sous la forme d'un seul superterrane. Le Superterrane Kazakh collisione avec un terrane Tarim-Nord Chinois (c'est-à-dire Terrane du Tianshan-Hanshan) durant le Dévonien et le continent Sibérien au Dévonien supérieur. Ce nouvel agencement des plaques induit une marge active continue le long des continents Sibérien, Kazakh et Nord Chinois et la fermeture de l'Océan Junggar-Balkash qui provoque le plissement oroclinal du Superterrane Kazakh durant le Carbonifère. L'histoire de la formation du Domaine Tarim-Nord Chinois est moins complexe. La marge passive nord Cambrienne devient active à l'Ordovicien et l'ouverture Silurienne du bassin d'arrière-arc du Tianshan sud mène à la formation du terrane du Tianshan-Hanshan. La collision Dévonienne entre ce dernier et le Superterrane Kazakh provoque la fermerture de l'Océan Tianshan sud. Finalement, la collision entre la Sibérie et la partie est du continent Tarim-Nord Chinois (c'est-à-dire Mongolie Intérieure) prend place durant le Permien suite à la fermeture de l'Océan Solonker. La majeure partie des Altaïdes est alors formée, seul l'Océan Mongol-Okhotsk est encore ouvert. Ce dernier se fermera seulement au Jurassique.

Termination of major ductile strike-slip shear and differential cooling along the Insubric line (Central Alps): U-Pb, Rb-Sr and 40Ar/39Ar ages of cross-cutting pegmatites

To constrain the age of strike-slip shear, related granitic magmatism, and cooling along the Insubric line, 29 size fractions of monazite and xenotime were dated by the U-Pb method, and a series of 25 Rb-Sr and Ar-40/Ar-39 ages were measured on different size fractions of muscovite and biotite. The three pegmatitic intrusions analyzed truncate high-grade metamorphic mylonite gneisses of the Simplon shear zone, a major Alpine structure produced in association with dextral strike-slip movements along the southern edge of the European plate, after collision with its Adriatic indenter. Pegmatites and aplites were produced between 29 and 25 Ma in direct relation to right-lateral shear along the Insubric line, by melting of continental crust having Sr-87/Sr-86 between 0.7199 and 0.7244 at the time of melting. High-temperature dextral strike-slip shear was active at 29.2 +/- 0.2 (2 sigma) Ma, and it terminated before 26.4 +/- 0.1 Ma. During dike injection, temperatures in the country rocks of the Isorno-Orselina and Monte Rosa structural units did not exceed approximate to 500 degrees C, leading to fast initial cooling, followed by slower cooling to approximate to 350 degrees C within several million years. In one case, initial cooling to approximate to 500 degrees C was significantly delayed by about 4 m.y., with final cooling to approximate to 300 degrees C at 20-19 Ma in all units. For the period between 29 and 19 Ma, cooling of the three sample localities was non-uniform in space and time, with significant variations on the kilometre scale. These differences are most likely due to strongly varying heat flow, and/or heterogeneous distribution of unroofing rates within the continuously deforming Insubric line. If entirely ascribed to differences in unroofing, corresponding rates would vary between 0.5 and 2.5 mm/y, for a thermal gradient of 30 degrees/km.

Cherenkov mesons as in-medium quark energy loss

We recently showed that a heavy quark moving su ciently fast through a quark-gluon plasma may lose energy by Cherenkov-radiating mesons [1]. Here we review our previous holographic calculation of the energy loss in N = 4 Super Yang-Mills and extend it to longitudinal vector mesons and scalar mesons. We also discuss phenomenological implications for heavy-ion collision experiments. Although the Cherenkov energy loss is an O(1=Nc) effect, a ballpark estimate yields a value of dE/dx for Nc = 3 which is comparable to that of other mechanisms.

Solar Powered Highway Delineator System, HR-367, 1993

Currently, many drivers experience some difficulty in viewing the road ahead of them during times of reduced visibility, such as rain, snow, fog, or the darkness of night- Recent studies done by the National Safety Council provide a detailed contrast between fatal accidents occurring during the day and night. Revealed was that the motor vehicle night death rate (4.41 deaths per 100 million miles driven) was sharply higher than the corresponding death rate during daylight hours (1.21). By providing a delineating system powered by the natural resource of solar power, a constant source of visibility may be maintained throughout the evening. Along with providing enough light to trace the outline of the road, other major goals defined in producing this delineator system are as follows: 1. A strong and durable design that would protect the internal components and survive extreme weather conditions. 2. A low maintenance system where components need few repairs or replacements. 3. A design which makes all components accessible in the event that maintenance is needed, but also prevents vandalism. 4. A design that provides greater visibility to drivers and will not harm a vehicle or its passengers in the event of a collision. This solar powered highway delineator consists of an adjustable solar array, a light fixture, and a standard delineator pole. The solar array houses and protects the solar panels, and can be easily adjusted to obtain a maximum amount of sunlight. The light fixture primarily houses the battery, the circuit and the light assembly. Both components allow for easy accessibility and reduce vandalism using internal connections for bolts and wires. The delineator mounting pole is designed to extensively deform in the event of a collision, therefore reducing any harm caused to the vehicle and/or the passengers. The cost of a single prototype to be produced is approximately $70.00 excluding labor costs. However, these material and labor costs will be greatly reduced if a large number of delineators are produced. It is recommended that the Iowa Department of Transportation take full advantage of the research and development put into this delineator design. The principles used in creating this delineator can be used to provide an outline for drivers to follow, or on a larger scale, provide actual roadway lighting in areas where it was never before possible or economically feasible. In either event, the number of fatal accidents will be decreased due to the improved driver visibility in the evening.

Pile Design and Tests for Integral Abutment Bridges, HR-273, 1987

Expansion joints increase both the initial cost and the maintenance cost of bridges. Integral abutment bridges provide an attractive design alternative because expansion joints are eliminated from the bridge itself. However, the piles in these bridges are subjected to horizontal movement as the bridge expands and contracts during temperature changes. The objective of this research was to develop a method of designing piles for these conditions. Separate field tests simulating a pile and a bridge girder were conducted for three loading cases: (1) vertical load only, (2) horizontal displacement of pile head only, and (3) combined horizontal displacement of pile head with subsequent vertical load. Both tests (1) and (3) reached the same ultimate vertical load, that is, the horizontal displacement had no effect on the vertical load capacity. Several model tests were conducted in sand with a scale factor of about 1:10. Experimental results from both the field and model tests were used to develop the vertical and horizontal load-displacement properties of the soil. These properties were input into the finite element computer program Integral Abutment Bridge Two-Dimensional (IAB2D), which was developed under a previous research contract. Experimental and analytical results compared well for the test cases. Two alternative design methods, both based upon the American Association of State Highway and Transportation Officials (AASHTO) Specification, were developed. Alternative One is quite conservative relative to IAB2D results and does not permit plastic redistribution of forces. Alternative Two is also conservative when compared to IAB2D, but plastic redistribution is permitted. To use Alternative Two, the pile cross section must have sufficient inelastic rotation capacity before local buckling occurs. A design example for a friction pile and an end-bearing pile illustrates both alternatives.

Validation of Design Recommendations for Integral Abutment Piles, HR-292, 1989

Since integral abutment bridges decrease the initial and maintenance costs of bridges, they provide an attractive alternative for bridge designers. The objective of this project is to develop rational and experimentally verified design recommendations for these bridges. Field testing consisted of instrumenting two bridges in Iowa to monitor air and bridge temperatures, bridge displacements, and pile strains. Core samples were also collected to determine coefficients of thermal expansion for the two bridges. Design values for the coefficient of thermal expansion of concrete are recommended, as well as revised temperature ranges for the deck and girders of steel and concrete bridges. A girder extension model is developed to predict the longitudinal bridge displacements caused by changing bridge temperatures. Abutment rotations and passive soil pressures behind the abutment were neglected. The model is subdivided into segments that have uniform temperatures, coefficients of expansion, and moduli of elasticity. Weak axis pile strains were predicted using a fixed-head model. The pile is idealized as an equivalent cantilever with a length determined by the surrounding soil conditions and pile properties. Both the girder extension model and the fixed-head model are conservative for design purposes. A longitudinal frame model is developed to account for abutment rotations. The frame model better predicts both the longitudinal displacement and weak axis pile strains than do the simpler models. A lateral frame model is presented to predict the lateral motion of skewed bridges and the associated strong axis pile strains. Full passive soil pressure is assumed on the abutment face. Two alternatives for the pile design are presented. Alternative One is the more conservative and includes thermally induced stresses. Alternative Two neglects thermally induced stresses but allows for the partial formation of plastic hinges (inelastic redistribution of forces). Ductility criteria are presented for this alternative. Both alternatives are illustrated in a design example.

Comparison between a linear ion trap and a triple quadruple MS in the sensitive detection of large peptides at femtomole amounts on column.

In addition to the importance of sample preparation and extract separation, MS detection is a key factor in the sensitive quantification of large undigested peptides. In this article, a linear ion trap MS (LIT-MS) and a triple quadrupole MS (TQ-MS) have been compared in the detection of large peptides at subnanomolar concentrations. Natural brain natriuretic peptide, C-peptide, substance P and D-Junk-inhibitor peptide, a full D-amino acid therapeutic peptide, were chosen. They were detected by ESI and simultaneous MS(1) and MS(2) acquisitions. With direct peptide infusion, MS(2) spectra revealed that fragmentation was peptide dependent, milder on the LIT-MS and required high collision energies on the TQ-MS to obtain high-intensity product ions. Peptide adsorption on surfaces was overcome and peptide dilutions ranging from 0.1 to 25 nM were injected onto an ultra high-pressure LC system with a 1 mm id analytical column and coupled with the MS instruments. No difference was observed between the two instruments when recording in LC-MS(1) acquisitions. However, in LC-MS(2) acquisitions, a better sensitivity in the detection of large peptides was observed with the LIT-MS. Indeed, with the three longer peptides, the typical fragmentation in the TQ-MS resulted in a dramatic loss of sensitivity (> or = 10x).

Advanced applications of scanning electron microscopy in geology

Nowadays Scanning Electron Microscopy (SEM) is a basic and fundamental tool in the study of geologic samples. The collision of a highlyaccelerated electron beam with the atoms of a solid sample results in theproduction of several radiation types than can be detected and analysed byspecific detectors, providing information of the chemistry and crystallography ofthe studied material. From this point of view, the chamber of a SEM can beconsidered as a laboratory where different experiments can be carried out. Theapplication of SEM to geology, especially in the fields of mineralogy andpetrology has been summarised by Reed (1996).The aim of this paper is to showsome recent applications in the characterization of geologic materials.

Tyyppipakosta kollisionratkaisuperiaatteisiin : ja mitä sen jälkeen?

Ylänimeke: Oppirakennelmia ja periaatteita

An Assessment of Traffic Safety in Urban Deer Herd Management Zones in Iowa, 2010

Many states are striving to keep their deer population to a sustainable and controllable level while maximizing public safety. In Iowa, measures to control the deer population include annual deer hunts and special deer herd management plans in urban areas. While these plans may reduce the deer population, traffic safety in these areas has not been fully assessed. Using deer population data from the Iowa Department of Natural Resources and data on deer-vehicle crashes and deer carcass removals from the Iowa Department of Transportation, the authors examined the relationship between deer-vehicle collisions, deer density, and land use in three urban areas in Iowa that have deer management plans in place (Cedar Rapids, Dubuque, and Iowa City) over the period 2002 to 2007. First, a comparison of deer-vehicle crash counts and deer carcass removal counts was conducted at the county level. Further, the authors estimated econometric models to investigate the factors that influence the frequency and severity of deer-vehicle crashes in these zones. Overall, the number of deer carcasses removed on the primary roads in these counties was greater than the number of reported deervehicle crashes on those roads. These differences can be attributed to a number of reasons, including variability in data reporting and data collection practices. In addition, high rates of underreporting of crashes were found on major routes that carry high volumes of traffic. This study also showed that multiple factors affect deer-vehicle crashes and corresponding injury outcomes in urban management zones. The identified roadway and non-roadway factors could be useful for identifying locations on the transportation system that significantly impact deer species and safety and for determining appropriate countermeasures for mitigation. Efforts to reduce deer density adjacent to roads and developed land and to provide wider shoulders on undivided roads are recommended. Improving the consistency and accuracy of deer carcass and deer-vehicle collision data collection methods and practices is also desirable.

A new classification of the Turkish terranes and sutures and its implication for the paleotectonic history of the region

The Turkish part of the Tethyan realm is represented by a series of terranes juxtaposed through Alpine convergent movements and separated by complex suture zones. Different terranes can be defined and characterized by their dominant geological background. The Pontides domain represents a segment of the former active margin of Eurasia, where back-arc basins opened in the Triassic and separated the Sakarya terrane from neighbouring regions. Sakarya was re-accreted to Laurasia through the Balkanic mid-Cretaceous orogenic event that also affected the Rhodope and Strandja zones. The whole region from the Balkans to the Caucasus was then affected by a reversal of subduction and creation of a Late Cretaceous arc before collision with the Anatolian domain in the Eocene. If the Anatolian terrane underwent an evolution similar to Sakarya during the Late Paleozoic and Early Triassic times, both terranes had a diverging history during and after the Eo-Cimmerian collision. North of Sakarya, the Küre back-arc was closed during the Jurassic, whereas north of the Anatolian domain, the back-arc type oceans did not close before the Late Cretaceous. During the Cretaceous, both domains were affected by ophiolite obduction, but in very different ways: north directed diachronous Middle to Late Cretaceous mélange obduction on the Jurassic Sakarya passive margin; Senonian synchronous southward obduction on the Triassic passive margin of Anatolia. From this, it appears that the Izmir-Ankara suture, currently separating both terranes, is composite, and that the passive margin of Sakarya is not the conjugate margin of Anatolia. To the south, the Cimmerian Taurus domain together with the Beydağları domain (part of the larger Greater Apulian terrane), were detached from north Gondwana in the Permian during the opening of the Neotethys (East-Mediterranean basin). The drifting Cimmerian blocks entered into a soft collision with the Anatolian and related terranes in the Eo-Cimmerian orogenic phase (Late Triassic), thus suturing the Paleotethys. At that time, the Taurus plate developed foreland-type basins, filled with flysch-molasse deposits that locally overstepped the lower plate Taurus terrane and were deposited in the opening Neotethys to the south. These olistostromal deposits are characterized by pelagic Carboniferous and Permian material from the Paleotethys suture zone found in the Mersin mélange. The latter, as well as the Antalya and Mamonia domains are represented by a series of exotic units now found south of the main Taurus range. Part of the Mersin exotic material was clearly derived from the former north Anatolian passive margin (Huğlu-type series) and re-displaced during the Paleogene. This led us to propose a plate tectonic model where the Anatolian ophiolitic front is linked up with the Samail/Baër-Bassit obduction front found along the Arabian margin. The obduction front was indented by the Anatolian promontory whose eastern end was partially subducted. Continued slab roll-back of the Neotethys allowed Anatolian exotics to continue their course southwestward until their emplacement along the Taurus southern margin (Mersin) and up to the Beydağları promontory (Antaya-Mamonia) in the latest Cretaceous-Paleocene. The supra-subduction ocean opening at the back of the obduction front (Troodos-type Ocean) was finally closed by Eocene north-south shortening between Africa and Eurasia. This brought close to each other Cretaceous ophiolites derived from the north of Anatolia and those obducted on the Arabian promontory. The latter were sealed by a Maastrichtian platform, and locally never affected by Alpine tectonism, whereas those located on the eastern Anatolian plate are strongly deformed and metamorphosed, and affected by Eocene arc magmatism. These observations help to reconstruct the larger frame of the central Tethyan realm geodynamic evolution.

Une carte des zones de cisaillement ductiles des Alpes Centrales

The main deformation structures due to the Tertiary continental collision in the Western Swiss Alps are ductile shear zones. Four main shear zones can be recognized on the structural map, each characterised by a different shear direction. The first D I shear zone with a X I, SE (transverse) stretching direction has been created during the under-thrusting towards the SE of the European plate under the Adriatic plate. This took place mainly by ductile deformation of the upper part of the European continental basement with the formation of the external massifs basement folds and the Penninic foldnappes. The second D II shear zone (Simplon ductile shear zone) is characterized by a XII stretching, dipping from 0 to 30-degrees to the SW (longitudinal stretching). It is approximately 10 km wide, and crosses the Alpine nappes in an oblique direction. It corresponds to a relative SW transport direction of the upper units together with the Adriatic plate. This dextral transpression zone is also responsible for the stretching parallel to the elongation of the Alpine belt. The third D III shear zone is made of mylonites with a steep stretching direction and corresponds to the hanging wall of the Canavese reverse fault. The D IV shear zones, dextral wrench zones combined with underthrusting movement, are characterised by a W and SW stretching direction. They were formed during and after the S facing backfolding which for instance made the Mischabel fold and the Boggioleto fold. Actually it occupies two narrow areas of more ductile rocks between the Mischabel backfold to the N and the Monte Rosa nappe to the S and allong the Canavese Line. These dextral shear zones represent probably the western continuation of the Tonale Line dextral wrench fault. The D I to IV ductile shear zone were formed under greenschist and amphibolite facies conditions during the Tertiary orogenic metamorphism. Their regional distribution is limited to the metamorphic ductile zone representing the deep part of the Alpine belt, between 10 and 30 km depth. The emplacement and orientation of the shear zones was also directed by the geometry of the boundaries of the European and Adriatic plates. The analysis of the superposed Central Alpine shear zones permits thus to propose a model of the history of the relative convergent and wrench movements which took place between the European and Adriatic plates during the Alpine Tertiary continental collision.

The birth of the Rheic Ocean - Early Palaeozoic subsidence patterns and subsequent tectonic plate scenarios

New plate-tectonic reconstructions of the Gondwana margin suggest that the location of Gondwana-derived terranes should not only be guided by the models, but should also consider the possible detrital input from some Asian blocks (Hunia), supposed to have been located along the Cambrian Gondwana margin, and accreted in the Silurian to the North-Chinese block. Consequently, the Gondwana margin has to be subdivided into a more western domain, where the future Avalonian blocks will be separated from Gondwana by the opening Rheic Ocean, whereas in its eastern continuation, hosting the future basement areas of Central Europe, different periods of crustal extension should be distinguished. Instead of applying a rather cylindrical model, it is supposed that crustal extension follows a much more complex pattern, where local back-arcs or intra-continental rifts are involved. Guided by the age data of magmatic rocks and the pattern of subsidence curves, the following extensional events can be distinguished: During the early to middle Cambrian, a back-arc setting guided the evolution at the Gondwana margin. Contemporaneous intra-continental rift basins developed at other places related to a general post-PanAfrican extensional phase affecting Africa Upper Cambrian formation of oceanic crust is manifested in the Chamrousse area, and may have lateral cryptic relics preserved in other places. This is regarded as the oceanisation of some marginal basins in a context of back-arc rifting. These basins were closed in a mid-Ordovician tectonic phase, related to the subduction of buoyant material (mid-ocean ridge?) Since the Early Ordovician, a new phase of extension is observed, accompanied by a large-scale volcanic activity, erosion of the rift shoulders generated detritus (Armorican Quartzite) and the rift basins collected detrital zircons from a wide hinterland. This phase heralded the opening of Palaeotethys, but it failed due to the Silurian collision (Eo-Variscan phase) of an intra-oceanic arc with the Gondwana margin. During this time period, at the eastern wing of the Gondwana margin begins the drift of the future Hunia microcontinents, through the opening of an eastern prolongation of the already existing Rheic Ocean. The passive margin of the remaining Gondwana was composed of the Galatian superterranes, constituents of the future Variscan basement areas. Remaining under the influence of crustal extension, they will start their drift to Laurussia since the earliest Devonian during the opening of the Palaeotethys Ocean. (C) 2008 Elsevier B.V. All rights reserved.

Performance Analysis of Two Quantum Reaction Dynamics Codes: Time-Dependent and Time-Independent Strategies

The computer simulation of reaction dynamics has nowadays reached a remarkable degree of accuracy. Triatomic elementary reactions are rigorously studied with great detail on a straightforward basis using a considerable variety of Quantum Dynamics computational tools available to the scientific community. In our contribution we compare the performance of two quantum scattering codes in the computation of reaction cross sections of a triatomic benchmark reaction such as the gas phase reaction Ne + H2+ %12. NeH++ H. The computational codes are selected as representative of time-dependent (Real Wave Packet [ ]) and time-independent (ABC [ ]) methodologies. The main conclusion to be drawn from our study is that both strategies are, to a great extent, not competing but rather complementary. While time-dependent calculations advantages with respect to the energy range that can be covered in a single simulation, time-independent approaches offer much more detailed information from each single energy calculation. Further details such as the calculation of reactivity at very low collision energies or the computational effort related to account for the Coriolis couplings are analyzed in this paper.