Learning and selection processes

In this paper I defend a teleological explanation of normativity, i. e., I argue that what an organism (or device) is supposed to do is determined by its etiological function. In particular, I present a teleological account of the normativity that arises in learning processes, and I defend it from some objections

The Role of Surfactant Properties of Extractants in Hydrometallurgical LiquidLiquid Extraction Processes

The amphiphilic nature of metal extractants causes the formation of micelles and other microscopic aggregates when in contact with water and an organic diluent. These phenomena and their effects on metal extraction were studied using carboxylic acid (Versatic 10) and organophosphorus acid (Cyanex 272) based extractants. Special emphasis was laid on the study of phase behaviour in a pre neutralisation stage when the extractant is transformed to a sodium or ammonium salt form. The pre neutralised extractants were used to extract nickel and to separate cobalt and nickel. Phase diagrams corresponding to the pre neutralisation stage in a metal extraction process were determined. The maximal solubilisation of the components in the system water(NH3)/extractant/isooctane takes place when the molar ratio between the ammonia salt form and the free form of the extractant is 0.5 for the carboxylic acid and 1 for the organophosphorus acid extractant. These values correspond to the complex stoichiometry of NH4A•HA and NIi4A, respectively. When such a solution is contacted with water a microemulsion is formed. If the aqueous phase contains also metal ions (e.g. Ni²+), complexation will take place on the microscopic interface of the micellar aggregates. Experimental evidence showing that the initial stage of nickel extraction with pre neutralised Versatic 10 is a fast pseudohomogeneous reaction was obtained. About 90% of the metal were extracted in the first 15 s after the initial contact. For nickel extraction with pre neutralised Versatic 10 it was found that the highest metal loading and the lowest residual ammonia and water contents in the organic phase are achieved when the feeds are balanced so that the stoichiometry is 2NH4+(org) = Nit2+(aq). In the case of Co/Ni separation using pre neutralised Cyanex 272 the highest separation is achieved when the Co/extractant molar ratio in the feeds is 1 : 4 and at the same time the optimal degree of neutralisation of the Cyanex 272 is about 50%. The adsorption of the extractants on solid surfaces may cause accumulation of solid fine particles at the interface between the aqueous and organic phases in metal extraction processes. Copper extraction processes are known to suffer of this problem. Experiments were carried out using model silica and mica particles. It was found that high copper loading, aromacity of the diluent, modification agents and the presence of aqueous phase decrease the adsorption of the hydroxyoxime on silica surfaces.

Espectrometria de massas com ionização por "electrospray": processos químicos envolvidos na formação de íons de substâncias orgânicas de baixo peso molecular

An overview of the current literature on the chemical processes involved in the ion formation from low molecular weight organic compounds by electrospray ionization mass spectrometry is given.

Foliar photochemical processes and carbon metabolism under favourable and adverse winter conditions in a Mediterranean mixed forest, Catalonia (Spain)

Evergreen trees in the Mediterranean region must cope with a wide range of environmental stresses from summer drought to winter cold. The mildness of Mediterranean winters can periodically lead to favourable environmental conditions above the threshold for a positive carbon balance, benefitting evergreen woody species more than deciduous ones. The comparatively lower solar energy input in winter decreases the foliar light saturation point. This leads to a higher susceptibility to photoinhibitory stress especially when chilly (< 12 C) or freezing temperatures (< 0 C) coincide with clear skies and relatively high solar irradiances. Nonetheless, the advantage of evergreen species that are able to photosynthesize all year round where a significant fraction can be attributed to winter months, compensates for the lower carbon uptake during spring and summer in comparison to deciduous species. We investigated the ecophysiological behaviour of three co-occurring mature evergreen tree species (Quercus ilex L., Pinus halepensis Mill., and Arbutus unedo L.). Therefore, we collected twigs from the field during a period of mild winter conditions and after a sudden cold period. After both periods, the state of the photosynthetic machinery was tested in the laboratory by estimating the foliar photosynthetic potential with CO2 response curves in parallel with chlorophyll fluorescence measurements. The studied evergreen tree species benefited strongly from mild winter conditions by exhibiting extraordinarily high photosynthetic potentials. A sudden period of frost, however, negatively affected the photosynthetic apparatus, leading to significant decreases in key physiological parameters such as the maximum carboxylation velocity (Vc,max), the maximum photosynthetic electron transport rate (Jmax), and the optimal fluorometric quantum yield of photosystem II (Fv/Fm). The responses of Vc,max and Jmax were highly species specific, with Q. ilex exhibiting the highest and P. halepensis the lowest reductions. In contrast, the optimal fluorometric quantum yield of photosystem II (Fv/Fm) was significantly lower in A. unedo after the cold period. The leaf position played an important role in Q. ilex showing a stronger winter effect on sunlit leaves in comparison to shaded leaves. Our results generally agreed with the previous classifications of photoinhibition-tolerant (P. halepensis) and photoinhibitionavoiding (Q. ilex) species on the basis of their susceptibility to dynamic photoinhibition, whereas A. unedo was the least tolerant to photoinhibition, which was chronic in this species. Q. ilex and P. halepensis seem to follow contrasting photoprotective strategies. However, they seemed equally successful under the prevailing conditions exhibiting an adaptive advantage over A. unedo. These results show that our understanding of the dynamics of interspecific competition in Mediterranean ecosystems requires consideration of the physiological behaviour during winter which may have important implications for long-term carbon budgets and growth trends.

Diesel/biodiesel soot oxidation with ceo2 and ceo2-zro2-modified cordierites: a facile way of accounting for their catalytic ability in fuel combustion processes

CeO2 and mixed CeO2-ZrO2 nanopowders were synthesized and efficiently deposited onto cordierite substrates, with the evaluation of their morphologic and structural properties through XRD, SEM, and FTIR. The modified substrates were employed as outer heterogeneous catalysts for reducing the soot originated from the diesel and diesel/biodiesel blends incomplete combustion. Their activity was evaluated in a diesel stationary motor, and a comparative analysis of the soot emission was carried out through diffuse reflectance spectroscopy. The analyses have shown that the catalyst-impregnated cordierite samples are very efficient for soot oxidation, being capable of reducing the soot emission in more than 60%.

A sensitive and robust lc-ms/ms method with monolithic column and electrospray ionization for the quantitation of efavirenz in human plasma: application to a bioequivalence study

An LC-MS/MS method has been developed for the determination of efavirenz (EFZ) in human plasma using hydrochlorothiazide as internal standard (I.S.). An ESI negative mode with multiple reaction-monitoring was used monitoring the transitions m/z 313.88→69.24 (EFZ) and 296.02→204.76 (I.S.). Samples were extracted using liquid-liquid extraction. The total run time was 2.0 min. The separation was achieved with HPLC-RP using a monolithic column. The assay was linear in the concentration range of 100 - 5000 ng mL-1. The mean recovery was 83%. Intra- and inter-day precision were < 9.5% and < 8.9%, respectively and accuracy was in the range ± 8.33%. The method was successfully applied to a bioequivalence study.

Microwave Processes in Ferrite-ferroelectric Layered Structure

This work is devoted to investigation of wave processes in new hybrid ferrite/ferroelectric structures. Spin wave devices based on ferrite films have disadvanteges. And their applications are limited. Investigated structures allow to overcome disadvantages. This investigation helps to create new class of devices. Electromagnetic analysis of hybrid spin-electromagnetic waves in ferrite/ferroelectric structures were done. As a result dispersion relation was found. Numerical solution of this dispersion relation gave us follow results. These structures can be effectively tuned by external electric and magnetic field. Methods to increase tuning range were suggested. It was found that such structures have one basic disadvantage which is connected with presence of thick ferroelectric layer. To solve this problem is to use thin ferroelectric films. But this decreases tuning range. It was confirmed by experiment that this structures can be effectively tuned by electric and magnetic fields. Resonance characteristics of ferrite/ferroelectric resonator were succesfully tuned by magnetic and electric field.

Quality and analysis of administration processes in server operations

IT outsourcing refers to the way companies focus on their core competencies and buy the supporting functions from other companies specialized in that area. Service is the total outcome of numerous of activities by employees and other resources to provide solutions to customers' problems. Outsourcing and service business have their unique characteristics. Service Level Agreements quantify the minimum acceptable service to the user. The service quality has to be objectively quantified so that its achievement or non-achievement of it can be monitored. Usually offshoring refers to the transferring of tasks to low-cost nations. Offshoring presents a lot of challenges that require special attention and they need to be assessed thoroughly. IT Infrastructure management refers to installation and basic usability assistance of operating systems, network and server tools and utilities. ITIL defines the industry best practices for organizing IT processes. This thesis did an analysis of server operations service and the customers’ perception of the quality of daily operations. The agreed workflows and processes should be followed better. Service providers’ processes are thoroughly defined but both the customer and the service provider might disobey them. Service provider should review the workflows regarding customer functions. Customer facing functions require persistent skill development, as they communicate the quality to the customer. Service provider needs to provide better organized communication and knowledge exchange methods between the specialists in different geographical locations.

Finnair Technical Procurement’s Processes and Service Quality

As primary objective, this thesis examines Finnair Technical Procurement’s service quality with its underlying process. As an internal unit, Technical Procurement serves as a link between external suppliers and internal customers. It is argued that external service quality requires a certain quality level within an organization. At the same time, aircraft maintenance business is subject to economic restraints. Therefore, a methodology was developed with a modified House of Quality that assists management in analyzing and evaluating Technical Procurement’s service level and connected process steps. It could be shown that qualitative and quantitative objectives do not exclude each other per se.

Evaluation of the dioxin and furan formation thermodynamics in combustion processes of urban solid wastes

Specific combustion programs (Gaseq, Chemical equilibria in perfect gases, Chris Morley) are used to model dioxin and formation in the incineration processes of urban solid wastes. Thanks to these programs, it is possible to establish correlations with the formation mechanisms postulated in literature on the subject. It was found that minimum oxygen quantities are required to obtain a significant formation of these compounds and that more furans than dioxins are formed. Likewise, dioxin and furan formation is related to the presence of carbon monoxide, and dioxin and furan distribution among its different compounds depends on the chlorine and hydrogen relative composition. This is due to the fact that an increased chlorine availability leads to the formation of compounds bearing a higher chlorine concentration (penta-, hexa-, hepta-, and octachlorides), whereas an increased hydrogen availability leads to the formation of compounds bearing a lower chlorine number (mono, di-, tri-, and tetrachlorides).

Understanding change processes in business networks : a study of convergence in Finnish telecommunications 1985-2005

Aktörer inom telekommunikationsbranschen i Finland har genomgått en intensiv förändring under de senaste 25 åren, från 1980-talets självständiga företag till företag beroende av varandra, och även av aktörer inom närliggande branscher. I dag skapas telekommunikationsmarknaden inte endast av operatörerna, utan också av mediebolag (t.ex. MTV Media) och IT-företag (t.ex. TietoEnator). Gränserna mellan olika industrier håller därmed på att suddas ut - ett fenomen som allmänt benämns som teknologisk konvergens. Konvergens innebär att någonting integreras; det kan handla om t.ex. teknologier (telefoni och Internet), företag (AOL och Time Warner), industrier (telekom, media och IT-branscherna), tjänster (mobilt TV), produkter (PDA) osv. Detta innebär att ytterst få telekomaktörer ensamma kan vidareutveckla marknaden och tekniska lösningar. Samarbete mellan aktörer krävs; mobiltelefontillverkare, innehållsproducenter, operatörer osv. bör intesifiera sitt samarbete för att kunna erbjuda attraktiva tjänster och produkter till kunder och slutanvändare. Avhandlingen fokuserar speciellt på affärsnätverk och samarbetsmönster mellan nätverksaktörer som medel för att få tillgång till resurser som krävs i en konvergenskarakteriserad affärsomgivning. Avhandlingen lyfter fram vad den teknologiska konvergensen har inneburit för telekomaktörer, dvs. att företag tvingats förändra sina strategier och verksamhetsmodeller. För många företag i branschen har anpassningen till konvergenstänkande varit utmanande, och i vissa fall kan man till och med tala om att företagen upplevt en identitetskris. Den utförda forskningen visar att konvergens uppfattas på marknaden som en pågående förändringsprocess, där varje telekomaktör är tvungen att utvärdera sin roll och position i relation till andra aktörer inom branschen. Konvergensprocesser forsätter i framtiden med ökad intensitet. Aktörerna skapar medvetet sin omgivning genom att agera i olika roller, som kan sträcka sig över industrigränser. Avhandlingen påvisar även att externa händelser och industrikontexten påverkar dynamiken i ett affärsnätverk.

Usability of laser–arc hybrid welding processes in industrial applications

Metal industries producing thick sections have shown increasing interest in the laser–arc hybrid welding process because of its clear advantages compared with the individual processes of autogenous laser welding and arc welding. One major benefit of laser–arc hybrid welding is that joints with larger gaps can be welded with acceptable quality compared to autogenous laser welding. The laser-arc hybrid welding process has good potential to extend the field of applications of laser technology, and provide significant improvements in weld quality and process efficiency in manufacturing applications. The objective of this research is to present a parameter set-up for laser–arc hybrid welding processes, introduce a methodical comparison of the chosen parameters, and discuss how this technology may be adopted in industrial applications. The research describes the principles, means and applications of different types of laser–arc hybrid welding processes. Conducted experiment processing variables are presented and compared using an analytical model which can also be used for predictive simulations. The main argument in this thesis is that profound understanding of the advanced technology of laser-arc hybrid welding will help improve the productivity of welding in industrial applications. Based on a review of the current knowledge base, important areas for further research are also identified. This thesis consists of two parts. The first part introduces the research topic and discusses laser–arc hybrid welding by characterizing its mechanism and most important variables. The second part comprises four research papers elaborating on the performance of laser– arc hybrid welding in the joining of metals. The study uses quantitative and qualitative research methods which include in-depth, interpretive analyses of results from a number of research groups. In the interpretive analysis, the emphasis is placed on the relevance and usefulness of the investigative results drawn from other research publications. The results of this study contribute to research on laser–arc hybrid welding by increasing understanding of how old and new perspectives on laser–arc hybrid welding are evidenced in industry. The research methodology applied permits continued exploration of how laser–arc hybrid welding and various process factors influence the overall quality of the weld. Thestudy provides a good foundation for future research, creates improved awareness of the laser–arc hybrid welding process, and assists the metal industry to maximize welding productivity.

Measuring Processes of a New Packaging Solutions with the Balanced Scorecard, case DigiCup

The aim of this study was to create a Balanced Scorecard to the DigiCup solution. The first goal was to create process descriptions to the few critical processes. The second goal was to define appropriate measurements, according to customer survey as well as following the Balanced Scorecard process description, to manage the critical success factors. The overall goal of this study was to create a performance measurement system for the solution which guides the operation towards continuous improvement. This study was conducted by using both qualitative and quantitative methods, and the analysis was done by using a case study method. The material was gathered from the current customers, the management and the employees using structured, semi-structured and open group and individual interviews. The current customers were divided into retailers and direct customers of the DigiCup solution. The questions which the customers were asked were related to the information about interviewee, company, business strategy, market, satisfaction survey and future requirements. The management defined the strategy and took part in specifying the perspectives, objectives and measurements to the Balanced Scorecard of the DigiCup solution. The employees participated into the choosing of the metrics. The material consisted from altogether sixteen interviews. At the beginning of the study the product development, the order-delivery as well as the printing processes was chosen to be the critical processes of the DigiCup solution. These processes were concentrated on already in the literature review while trying to find the characteristics of these processes as well as the critical success factors and the appropriate measurements, which could be utilized when creating the Balanced Scorecard to the DigiCup solution according to the customer survey. The appropriate perspectives, objectives and measurements were found to the DigiCup solution. The chosen measures works as a basis for the development of IT-reporting tool. As a conclusion it can be stated that when discussing a new business, where the objectives are changing according to which development’s phases the company is in, the measurement should be updated often enough.

Evaluation of energy efficiency and best available techniques in pumping processes

The potential for enhancing the energy efficiency of industrial pumping processes is estimated to be in some cases up to 50 %. One way to define further this potential is to implement techniques in accordance to definition of best available techniques in pumping applications. These techniques are divided into three main categories: Design, control method & maintenance and distribution system. In the theory part of this thesis first the definition of best available techniques (BAT) and its applicability on pumping processes is issued. Next, the theory around pumping with different pump types is handled, the main stress being in centrifugal pumps. Other components needed in a pumping process are dealt by presenting different control methods, use of an electric motor, variable speed drive and the distribution system. Last part of the theory is about industrial pumping processes from water distribution, sewage water and power plant applications, some of which are used further on in the empirical part as example cases. For the empirical part of this study four case studies on typical pumping processes from older Master’s these were selected. Firstly the original results were analyzed by studying the distribution of energy consumption between different system components and using the definition of BAT in pumping, possible ways to improve energy efficiency were evaluated. The goal in this study was that by the achieved results it would be possible to identify the characteristic energy consumption of these and similar pumping processes. Through this data it would then be easier to focus energy efficiency actions where they might be the most applicable, both technically and economically.