Semi-selective culture medium for Exserohilum turcicum isolation from corn seeds

Northern corn leaf blight, caused by Exserohilum turcicum (Et), is a disease of widespread occurrence in regions where corn, sweetcorn and popcorn are grown. This disease has great potential to cause damage and has been studied for years, but the association of its causal agent with seeds remains unconfirmed. Thus, the availability of a sensitive method to detect and quantify the inoculum in seeds, even at low incidence, is essential. The aim of this study was to develop a method to detect and quantify the presence of the fungus infecting and infesting corn and popcorn seeds. Artificially and naturally infected seeds were employed to develop the medium. The semi-selective medium was composed of carbendazim (active ingredient) (60 mg/L), captan (30 mg/L), streptomycin sulfate (500 mg/L) and neomycin sulfate (600 mg/L) aggregated to the medium lactose casein hydrolysate agar medium. By using this, Et was detected in naturally infected corn seeds, showing 0.124% incidence, in four out of ten analyzed samples. In addition, 1.04 conidia were detected per infested seed. By means of isolation, pathogenicity test, morphological characterization and comparison with descriptions of the species in the literature, the fungus isolated from the seeds was confirmed to be Et. Both infection and infestation were considered low; thus, for studies of Et detection in corn seeds, the use of semi-selective medium and more than 1,200 seeds/sample is suggested.

Studies on Neuromuscular Blocking Agents and Their Antagonists During Anaesthesia

Neuromuscular blocking agents (NMBAs) are widely used in clinical anaesthesia and emergency medicine. Main objectives are to facilitate endotracheal intubation and to allow surgery by reducing muscle tone and eliminating sudden movements, which may otherwise lead to trauma and complications. The most commonly used NMBAs are non-depolarizing agents with a medium duration of action, such as rocuronium and cisatracurium. They bind to the acetylcholine receptors in the neuromuscular junction, thus inhibiting the depolarization of the postsynaptic (muscular) membrane, which is a prerequisite for muscle contraction to take place. Previously, it has been assumed that nitrous oxide (N2O), which is commonly used in combination with volatile or intravenous anaesthetics during general anaesthesia, has no effect on NMBAs. Several studies have since claimed that N2O in fact does increase the effect of NMBAs when using bolus administration of the relaxant. The effect of N2O on the infusion requirements of two NMBAs (rocuronium and cisatracurium) with completely different molecular structure and pharmacological properties was assessed. A closed-loop feedback controlled infusion of NMBA with duration of at least 90 minutes at a 90% level of neuromuscular block was used. All patients received total intravenous anaesthesia (TIVA) with propofol and remifentanil. In both studies the study group (n=35) received N2O/Oxygen and the control group (n=35) Air/Oxygen. There were no significant differences in the mean steady state infusion requirements of NMBA (rocuronium in Study I; cisatracurium in Study II) between the groups in either study. In Study III the duration of the unsafe period of recovery after reversal of rocuronium-induced neuromuscular block by using neostigmine or sugammadex as a reversal agent was analyzed. The unsafe period of recovery was defined as the time elapsed from the moment of no clinical (visual) fade in the train-of-four (TOF) sequence until an objectively measured TOF-ratio of 0.90 was achieved. The duration of these periods were 10.3 ± 5.5 and 0.3 ± 0.3 min after neostigmine and sugammadex, respectively (P < 0.001). Study IV investigated the possible effect of reversal of a rocuronium NMB by sugammadex on depth of anaesthesia as indicated by the bispectral index and entropy levels in thirty patients. Sugammadex did not affect the level of anaesthesia as determined by EEG-derived indices of anaesthetic depth such as the bispectral index and entropy.

Switching components for medium voltage drives

Nowadays power drives are the essential part almost of all technological processes. Improvement of efficiency and reduction of losses require development of semiconductor switches. It has a particular meaning for the constantly growing market of renewable sources, especially for wind turbines, which demand more powerful semiconductor devices for control with growth of power. Also at present semiconductor switches are the key component in energy transmission, optimization of generation and network connection. The aim of this thesis is to make a survey of contemporary semiconductor components, showing difference in structures, advantages, disadvantages and most suitable applications. There is topical information about voltage, frequency and current limits of different switches. Study tries to compare dimensions and price of different components. Main manufacturers of semiconductor components are presented with the review of devices produced by them, and a conclusion about their availability was made. IGBT is selected as a main component in this study, because nowadays it is the most attractive component for usage in power drives, especially at the low levels of medium voltage. History of development of IGBT structure, static and dynamic characteristics are considered. Thesis tells about assemblies and connection of components and problems which can appear. One of key questions about semiconductor materials and their future development was considered. For the purpose of comparison strong and weak sides of different switches, calculation of losses of IGBT and its basic competitor – IGCT is presented. This master’s thesis makes an effort to answer the question if there are at present possibilities of accurate selection of switches for electrical drives of different rates of power and looks at future possible ways of development of semiconductor market.

Challenges of business process automation for small and medium enterprises

The aim of the study was to examine problems that small and medium enterprises are facing during the implementation of business process automation projects. Study reveals problems from the point of view of companies who are implementing automation projects and from the point of view of IT-integrators who are specifying in IT solutions for small and medium companies.

Application of Open Innovation Paradigm in Small and Medium Enterprises in Russia

The objective of this study is to explore how the Open Innovation paradigm is applied in by small and medium-size enterprises in Russia. The focus of the study is to understand how the processes of research and development and commercialization proceed in these kind of companies and to which extent they apply open innovation principles. Russian leadership makes certain steps for transition from the export of raw materials to an innovative model of economic growth. The research aims to disclose actual impact of these attempts. The closed innovation model and the erosion factors which lead to the destruction of an old one and emergence of new model are described. Features of open innovation implementation and intellectual property rights protection in small and medium enterprises are presented. To achieve the objective, a qualitative case study approach was chosen. Research includes facts and figures, views and opinions of management of studied companies related to innovation process in the company and in Russia in general. The research depicts the features of Open Innovation implementation by SMEs in Russia. A large number of research centers with necessary equipment and qualified personnel allow case companies to use external R&D effectively. They cooperate actively with research institutes, universities and laboratories. Thus, they apply inbound Open Innovation. On the contrary, lack of venture capital, low demand for technologies within the domestic market and weak protection of intellectual property limit the external paths to new markets. Licensing-out and creation of spin-off are isolated cases. Therefore, outbound Open Innovation is not a regular practice.

Pk-yrityksen polku systemaattiseen tuote- ja elinkaaritiedon hallintaan

Tutkimus on tehty Tekesin DTP-ohjelman Sinfonet-tutkimusprojektin puitteissa aikavälillä 2009-2011. Työssä on laadittu kokonaisvaltainen tuote- ja elinkaaritiedon hallinnan (eng. Product Lifecycle Management, PLM) tiekartta ja kehityssuunnitelma pienelle engineering-yritykselle. Työ käsittelee asiakkaan erikoisvaatimusten mukaan räätälöitävän tuotteen tuote- ja elinkaaritiedon hallinnan systematisointia pk-yrityksessä. Vaikka PLM-tiekartta on laadittu yksittäiselle yritykselle, sitä voidaan tietyin edellytyksin soveltaa myös toisten pk-yritysten tai engineeringyritysten PLM:n kehittämiseen. Teoriassa tarkastellaan ensinnäkin kohdeyritykseen liittyviä erityispiirteitä, pyritään ymmärtämään engineering–yrityksen ja pk-yrityksen erikoispiirteitä sekä niiden vaikutusta PLM:n kehittämiseen. Toiseksi esitellään PLM:n viittä keskeistä osaaluetta, yksi- ja viisiulotteisten PLM-kypsyysmallien käyttöä yrityksen nykytilan arvioimiseksi sekä rakennetaan engineering-yrityksen kokonaisvaltainen PLM-malli ja kahdeksan askeleen PLM-kehityspolku. PLM-malli jäsentää tiedonhallintaa prosessien kautta ja se koostuu viidestä osaalueesta: strategia identifioi asiakastarpeet sekä määrittelee kuinka tuotteiden ja prosessien avulla asiakastarpeet tyydytetään; prosessit ovat yrityksen toiminnan ydin, joissa tuotemallit ja tuote- ja tietorakenteet kehitetään sekä tuoteyksilöt toimitetaan asiakkaalle; rakenteet pohjautuvat strategiassa valittuun tuote- ja tiedonhallinnan strategiaan ja niiden tehtävänä on tukea ja tehostaa toimintaprosesseja; kulttuuri ja ihmiset muodostavat aineettoman pääoman, jonka vaikutuksesta prosessit toimivat ja tuotteet pystytään toimittamaan asiakkaalle; informaatioteknologia on työkalu, jota käytetään prosesseissa ja tietorakenteiden ylläpidossa, pääosin dokumentoidun tiedon luomiseen, hankitaan, varastoimiseen, jakamiseen ja soveltamiseen. Tapaustutkimuksessa kuvataan kohdeyrityksen nykytilaa PLM:n viidellä keskeisellä osa-alueella, tehdään PLM kypsyysarvio kahdella menetelmällä, määritellään yrityksen tavoitetila ja laaditaan yritykselle ensin alustava PLM roadmap ja lopulta kokonaisvaltaiseen PLM-malliin perustuva PLM roadmap ja PLM:n jatkokehityssuunnitelma.

Energy Efficiency of Pumping Medium Consistency Pulp with Centrifugal Pump

Approximately a quarter of electrical power consumption in pulp and paper industry is used in different pumping systems. Therefore, improving pumping system efficiency is a considerable way to reduce energy consumption in different processes. Pumping of wood pulp in different consistencies is common in pulp and paper industry. Earlier, centrifugal pumps were used to pump pulp only at low consistencies, but development of MC technology has made it possible to pump medium consistency pulp. Pulp is a non-Newtonian fluid, which flow characteristics are significantly different than what of water. In this thesis is examined the energy efficiency of pumping medium consistency pulp with centrifugal pump. The factors effecting the pumping of MC pulp are presented and through case study is examined the energy efficiency of pumping in practice. With data obtained from the case study are evaluated the effects of pump rotational speed and pulp consistency on energy efficiency. Additionally, losses caused by control valve and validity of affinity laws in pulp pumping are evaluated. The results of this study can be used for demonstrating the energy consumption of MC pumping processes and finding ways to improve energy efficiency in these processes.

Evaluation of cotton stalks destroyers

The destruction of the cotton crop residues (cotton stalks) is a mandatory procedure in Brazil for prophylactic issues, but is a subject unexplored by the research and there are few studies that deal with this issue. However, this is not encouraged in recent decades, studies aimed at developing and evaluating equipment for this purpose. The present study had the objective to evaluate six methods for mechanical destruction of cotton crop residues. Each method was defined based on the principle of operation of the active parts of the equipment, which were tested in medium texture soil and in a clayey one. The variables used to evaluate the efficiency of the equipment were the regrowth rate, the theoretical field capacity and energy demand. The equipment with convergent concave disks (DCC) and flat cutters discs from manufacturer A (CPS-a) showed the best results in cotton stalks destruction in both soil types. The harrow disc (GPD) was efficient only in clay soil. It was concluded that the equipment with convergent concave disks, among those tested, was the most efficient to destroy cotton stalks, regardless of soil type, and that the harrow disc was not included among the best performers.

Cassava starch extraction effluent treatment in a one phase tubular horizontal pilot reactor with support medium

The cassava starch industries generate a large volume of wastewater effluent that, stabilized in ponds, wastes its biogas energy and pollutes the atmosphere. To contribute with the reversion of this reality, this manipueira treatment research was developed in one phase anaerobic horizontal pilot reactor with support medium in bamboo pieces. The reactor was excavated into the ground and sealed with geomembrane in HDPE, having a volume equal to 33.6 m³ and continuous feeding by gravity. The stability indicators were pH, volatile acidity/total alkalinity ratio and biogas production. The statistical analyses were performed by a completely randomized design, with answers submitted to multivariate analysis. The organical loads in COD were 0.556; 0.670; 0.678 and 0.770 g L-1 and in volatile solids (VS) of 0.659; 0.608; 0.570 and 0.761 g L-1 for the hydraulic retention times (HRT) of 13.0; 11.5; 10.0 and 7.0 days, respectively. The reductions in COD were 88; 80; 88 and 67% and for VS of 76; 77; 65 and 61%. The biogas productions relatively to the consumed COD were 0.368; 0.795; 0.891 and 0.907 Lg-1, for the consumed VS of 0.524; 0.930; 1.757 and 0.952 Lg-1 and volumetric of 0.131; 0.330; 0.430 and 0.374 L L-1 d-1. The reactor remained stable and the bamboo pieces, in visual examination at the end of the experiment, showed to be in good physical conditions.

Spray adjuvant characteristics affecting agricultural spraying drift

This study defined the main adjuvant characteristics that may influence or help to understand drift formation process in the agricultural spraying. It was evaluated 33 aqueous solutions from combinations of various adjuvants and concentrations. Then, drifting was quantified by means of wind tunnel; and variables such as percentage of droplets smaller than 50 μm (V50), 100 μm (V100), diameter of mean volume (DMV), droplet diameter composing 10% of the sprayed volume (DV0.1), viscosity, density and surface tension. Assays were performed in triplicate, using Teejet XR8003 flat fan nozzles at 200 kPa (medium size droplets). Spray solutions were stained with Brilliant Blue Dye at 0.6% (m/ v). DMV, V100, viscosity cause most influence on drift hazardous. Adjuvant characteristics and respective methods of evaluation have applicability in drift risk by agricultural spray adjuvants.

Marketing-Sales Cooperation and its Relation on Direct Sales Performance: an Example of a Medium-sized Oil Company

The study touches upon marketing-sales departments’ cooperation and investigates marketing-sales cooperative model within the case company. So that research increases understanding of linkages between Marketing and Sales departments with an illustrative example of Russian medium-sized oil company (LLC Neste St. Petersburg), the subsidiary of Finnish-based Neste Oil. The empirical study is done from marketing and sales perspectives. And for sales main attention was brought to direct sales, both B2B and B2C. Research considers all five domains of cooperation, and among others, study reveals the attitude towards external (market) and internal (product) knowledge, and its mutual use by marketing and sales managers. A qualitative research method, participant observations, and in-depth interviews with upper-management made it possible to explore all facets of joint work. Moreover, research responses the changes in a model of cooperation between marketing and sales when moving from medium size to large company.

Working capital management in the small and medium-sized enterprises Case: Project-based business environment in Flowrox Oy

This Master´s thesis illustrates how growing a business ties up the company´s working capital and what the cost of committed capital. In order to manage a company´s working capital in rapid business growth phase, the thesis suggests that by monitoring and managing the operating and cash conversion cycles of customers´ projects, a company can find ways to secure the required amount of capital. The research method of this thesis was based on literature reviews and case study research. The theoretical review presents the concepts of working capital and provides the background for understanding how to improve working capital management. The company in subject is a global small and medium-sized enterprise that manufactures pumps and valves for demanding process conditions. The company is expanding, which creates lots of challenges. This thesis concentrates to the company´s working capital management and its efficiency through the supply chain and value chain perspective. The main elements of working capital management are inventory management, accounts receivable management and accounts payable management. Prepayments also play a significant role, particularly in project-based businesses. Developing companies´ working capital management requires knowledge from different kind of key operations´ in the company, like purchasing, production, sales, logistics and financing. The perspective to develop and describe working capital management is an operational. After literature reviews the thesis present pilot projects that formed the basis of a model to monitor working capital in the case company. Based on analysis and pilot projects, the thesis introduces a rough model for monitoring capital commitments in short time period. With the model the company can more efficiently monitor and manage their customer projects.