Photocatalytic activities of tin(IV) oxide surface-modified titanium(IV) dioxide show a strong sensitivity to the TiO 2 crystal form

Surface modification of rutile TiO2 with extremely small SnO2 clusters gives rise to a great increase in its UV light activity for degradation of model organic water pollutants, while the effect is much smaller for anatase TiO2. This crystal form sensitivity is rationalized in terms of the difference in the electronic modification of TiO2 through the interfacial Sn−O−Ti bonds. The increase in the density of states near the conduction band minimum of rutile by hybridization with the SnO2 cluster levels intensifies the light absorption, but this is not seen with modified anatase. The electronic transition from the valence band to the conduction band causes the bulk-to-surface interfacial electron transfer to enhance charge separation. Further, electrons relaxed to the conduction minimum are smoothly transferred to O2 due to the action of the SnO2 species as an electron transfer promoter.

HER2 in high-risk rectal cancer patients treated in EXPERT-C, a randomized phase II trial of neoadjuvant capecitabine and oxaliplatin (CAPOX) and chemoradiotherapy (CRT) with or without cetuximab.

BACKGROUND: HER2 is an established therapeutic target in breast and gastric cancers. The role of HER2 in rectal cancer is unclear, as conflicting data on the prevalence of HER2 expression in this disease have been reported. We evaluated the prevalence of HER2 and its impact on the outcome of high-risk rectal cancer patients treated with neoadjuvant CAPOX and CRT±cetuximab in the EXPERT-C trial. PATIENTS AND METHODS: Eligible patients with available tumour tissue for HER2 analysis were included. HER2 expression was determined by immunohistochemistry (IHC) in pre-treatment biopsies and/or surgical specimens (score 0-3+). Immunostaining was scored according to the consensus panel recommendations on HER2 scoring for gastric cancer. Tumours with equivocal IHC result (2+) were tested for HER2 amplification by D-ISH. Tumours with IHC 3+ or D-ISH ratio ≥2.0 were classified as HER2+. The impact of HER2 on primary and secondary end points of the study was analysed. RESULTS: Of 164 eligible study patients, 104 (63%) biopsy and 114 (69%) surgical specimens were available for analysis. Only 3 of 104 (2.9%) and 3 of 114 (2.6%) were HER2+, respectively. In 77 patients with paired specimens, concordance for HER2 status was found in 74 (96%). Overall, 141 patients were assessable for HER2 and 6 out of 141 (4.3%) had HER2 overexpression and/or amplification. The median follow-up was 58.6 months. HER2 was not associated with a difference in the outcome for any of the study end points, including in the subset of 90 KRAS/BRAF wild-type patients treated±cetuximab. CONCLUSIONS: Based on the low prevalence of expression as recorded in the EXPERT-C trial, HER2 does not appear to represent a useful therapeutic target in high-risk rectal cancer. However, the role of HER2 as a potential predictive biomarker of resistance to anti-EGFR-based treatments and a therapeutic target in anti-EGFR refractory metastatic colorectal cancer (CRC) warrants further investigation. TRIAL REGISTRATION: ISRCTN Register: 99828560.

Multicenter randomized phase II clinical trial comparing neoadjuvant oxaliplatin, capecitabine, and preoperative radiotherapy with or without cetuximab followed by total mesorectal excision in patients with high-risk rectal cancer (EXPERT-C).

PURPOSE: To evaluate the addition of cetuximab to neoadjuvant chemotherapy before chemoradiotherapy in high-risk rectal cancer. PATIENTS AND METHODS: Patients with operable magnetic resonance imaging-defined high-risk rectal cancer received four cycles of capecitabine/oxaliplatin (CAPOX) followed by capecitabine chemoradiotherapy, surgery, and adjuvant CAPOX (four cycles) or the same regimen plus weekly cetuximab (CAPOX+C). The primary end point was complete response (CR; pathologic CR or, in patients not undergoing surgery, radiologic CR) in patients with KRAS/BRAF wild-type tumors. Secondary end points were radiologic response (RR), progression-free survival (PFS), overall survival (OS), and safety in the wild-type and overall populations and a molecular biomarker analysis. RESULTS: One hundred sixty-five eligible patients were randomly assigned. Ninety (60%) of 149 assessable tumors were KRAS or BRAF wild type (CAPOX, n = 44; CAPOX+C, n = 46), and in these patients, the addition of cetuximab did not improve the primary end point of CR (9% v 11%, respectively; P = 1.0; odds ratio, 1.22) or PFS (hazard ratio [HR], 0.65; P = .363). Cetuximab significantly improved RR (CAPOX v CAPOX+C: after chemotherapy, 51% v 71%, respectively; P = .038; after chemoradiation, 75% v 93%, respectively; P = .028) and OS (HR, 0.27; P = .034). Skin toxicity and diarrhea were more frequent in the CAPOX+C arm. CONCLUSION: Cetuximab led to a significant increase in RR and OS in patients with KRAS/BRAF wild-type rectal cancer, but the primary end point of improved CR was not met.

Comprendre et maîtriser le passage de type I à type II de puits quantiques d'In(x)Ga(1-x)As(y)Sb(1-y) sur substrat de GaSb

Les antimoniures sont des semi-conducteurs III-V prometteurs pour le développement de dispositifs optoélectroniques puisqu'ils ont une grande mobilité d'électrons, une large gamme spectrale d'émission ou de détection et offrent la possibilité de former des hétérostructures confinées dont la recombinaison est de type I, II ou III. Bien qu'il existe plusieurs publications sur la fabrication de dispositifs utilisant un alliage d'In(x)Ga(1-x)As(y)Sb(1-y) qui émet ou détecte à une certaine longueur d'onde, les détails, à savoir comment sont déterminés les compositions et surtout les alignements de bande, sont rarement explicites. Très peu d'études fondamentales sur l'incorporation d'indium et d'arsenic sous forme de tétramères lors de l'épitaxie par jets moléculaires existent, et les méthodes afin de déterminer l'alignement des bandes des binaires qui composent ces alliages donnent des résultats variables. Un modèle a été construit et a permis de prédire l'alignement des bandes énergétiques des alliages d'In(x)Ga(1-x)As(y)Sb(1-y) avec celles du GaSb pour l'ensemble des compositions possibles. Ce modèle tient compte des effets thermiques, des contraintes élastiques et peut aussi inclure le confinement pour des puits quantiques. De cette manière, il est possible de prédire la transition de type de recombinaison en fonction de la composition. Il est aussi montré que l'indium ségrègue en surface lors de la croissance par épitaxie par jets moléculaires d'In(x)Ga(1-x)Sb sur GaSb, ce qui avait déjà été observé pour ce type de matériau. Il est possible d'éliminer le gradient de composition à cette interface en mouillant la surface d'indium avant la croissance de l'alliage. L'épaisseur d'indium en surface dépend de la température et peut être évaluée par un modèle simple simulant la ségrégation. Dans le cas d'un puits quantique, il y aura une seconde interface GaSb sur In(x)Ga(1-x)Sb où l'indium de surface ira s'incorporer. La croissance de quelques monocouches de GaSb à basse température immédiatement après la croissance de l'alliage permet d'incorporer rapidement ces atomes d'indium et de garder la seconde interface abrupte. Lorsque la composition d'indium ne change plus dans la couche, cette composition correspond au rapport de flux d'atomes d'indium sur celui des éléments III. L'arsenic, dont la source fournit principalement des tétramères, ne s'incorpore pas de la même manière. Les tétramères occupent deux sites en surface et doivent interagir par paire afin de créer des dimères d'arsenic. Ces derniers pourront alors être incorporés dans l'alliage. Un modèle de cinétique de surface a été élaboré afin de rendre compte de la diminution d'incorporation d'arsenic en augmentant le rapport V/III pour une composition nominale d'arsenic fixe dans l'In(x)Ga(1-x)As(y)Sb(1-y). Ce résultat s'explique par le fait que les réactions de deuxième ordre dans la décomposition des tétramères d'arsenic ralentissent considérablement la réaction d'incorporation et permettent à l'antimoine d'occuper majoritairement la surface. Cette observation montre qu'il est préférable d'utiliser une source de dimères d'arsenic, plutôt que de tétramères, afin de mieux contrôler la composition d'arsenic dans la couche. Des puits quantiques d'In(x)Ga(1-x)As(y)Sb(1-y) sur GaSb ont été fabriqués et caractérisés optiquement afin d'observer le passage de recombinaison de type I à type II. Cependant, celui-ci n'a pas pu être observé puisque les spectres étaient dominés par un niveau énergétique dans le GaSb dont la source n'a pu être identifiée. Un problème dans la source de gallium pourrait être à l'origine de ce défaut et la résolution de ce problème est essentielle à la continuité de ces travaux.

Greener methodology for the synthesis of alpha-diazocarbonyl compounds and a novel approach to dioxinone derivatives

This thesis outlines a more environmentally benign approach to diazo transfer, and the investigation of the reactivity of -diazocarbonyl compounds when subjected to transition metal and lanthanide catalysis. Extensive studies were carried out to find the optimum conditions for a greener diazo transfer methodology, and this was also applied to a continuous process for the synthesis of -diazo--ketoesters. The first chapter includes a literature review of the synthesis and subsequent reactivity of -diazocarbonyl compounds. An overview of the applications of flow chemistry for the synthesis of hazardous intermediates is also included. The applications of lanthanide catalysts in organic synthesis is also discussed. The second chapter outlines the extensive studies undertaken to determine the optimum conditions for a greener diazo transfer methodology, including base and solvent studies. Use of water as a viable solvent for diazo transfer was successfully investigated. Diazo transfer to a range of -diazo--ketoesters was achieved using 5 mol% triethylamine or DMAP in water with high conversions. Polystyrene-supported benzenesulfonyl azide as an alternative diazo transfer reagent was also explored, as well as investigations into cheaper generation of this safer reagent. This polymer-supported benzenesulfonyl azide was used with 25 mol% of base in water to achieve successful diazo transfer to a range of -diazo--ketoesters. The third chapter describes the application of the new methodology developed in Chapter 2 to a continuous processing approach. Various excellent conditions were identified for both batch and flow reactions. A series of -diazo--ketoesters were synthesised with excellent conversions using 25 mol% triethylamine in 90:10 acetone water using flow chemistry. Successful diazo transfer was also achieved using a polymer-supported benzenesulfonyl azide in water under flow conditions. The fourth chapter discusses the reactivity of -diazo--ketoesters under transition metal and lanthanide catalysis. This chapter describes the synthesis of a range of -ketoesters via transesterification, which were used to synthesise a range of novel -diazo--ketoesters that were used in subsequent decomposition reactions. A novel route to dioxinones via rhodium(II) catalysis is reported. Attempted OH and SH insertion reactions in the presence of various lanthanide(II) catalysts are outlined, leading to some unexpected and interesting rearrangement products. The experimental details, including spectroscopic and analytical data for all compounds prepared, are reported at the end of each chapter.

Aroylhydrazone Cu(II) complexes in keto form: structural characterization and catalytic cctivity towards cyclohexane oxidation

The reaction of the Schiff base (3,5-di-tert-butyl-2-hydroxybenzylidene)-2-hydroxybenzohydrazide (H3L) with a copper(II) salt of a base of a strong acid, i.e., nitrate, chloride or sulphate, yielded the mononuclear complexes [Cu(H2L)(NO3)(H2O)] (1), [Cu(H2L)Cl]center dot 2MeOH (2) and the binuclear complex [{Cu(H2L)}(2)(mu-SO4)]center dot 2MeOH (3), respectively, with H2L- in the keto form. Compounds 1-3 were characterized by elemental analysis, Infrared (IR) spectroscopy, Electrospray Ionisation-Mass Spectrometry (ESI-MS) and single crystal X-ray crystallography. All compounds act as efficient catalysts towards the peroxidative oxidation of cyclohexane to cyclohexyl hydroperoxide, cyclohexanol and cyclohexanone, under mild conditions. In the presence of an acid promoter, overall yields (based on the alkane) up to 25% and a turnover number (TON) of 250 (TOF of 42 h(-1)) after 6 h, were achieved.

Impact of different solvents on the recovery of bioactive compounds and antioxidant properties from lemon (Citrus limon L.) pomace waste

The effects of different solvents on the recovery of (i) extractable solids (ES), (ii) total phenolic compounds (TPC), (iii) total flavonoid content (TFC), (iv) vitamin C, and (v) antioxidant activity from lemon pomace waste were investigated. The results revealed that solvents significantly affected the recovery of ES, TPC, TFC, and antioxidant properties. Absolute methanol and 50% acetone resulted in the highest extraction yields of TPC, whereas absolute methanol resulted in the highest extraction of TFC, and water had the highest recovery of vitamin C. 50% ethanol, and 50% acetone had higher extraction yields for TPC, and TFC, as well as higher antioxidant activity compared with their absolute solvents and water. TPC and TFC were shown to be the major components contributing to the antioxidant activity of lemon pomace.

Synthesis, characterization and chemical vapor deposition of transition metal di(tert-butyl)amido compounds

Although the transition metal chemistry of many dialkylamido ligands has been well studied, the chemistry of the bulky di(tert-butyl)amido ligand has been largely overlooked. The di(tert-butyl)amido ligand is well suited for synthesizing transition metal compounds with low coordination numbers; such compounds may exhibit interesting structural, physical, and chemical properties. Di(tert-butyl)amido complexes of transition metals are expected to exhibit high volatilities and low decomposition temperatures, thus making them well suited for the chemical vapor deposition of metals and metal nitrides. Treatment of MnBr₂(THF)₂, FeI₂, CoBr₂(DME), or NiBr₂(DME) with two equivalents of LiN(t-Bu)2 in benzene affords the two-coordinate complex M[N(t-Bu)₂]₂, where M is Mn, Fe, Co, or Ni. Crystallographic studies show that the M-N distances decrease across the series: 1.9365 (Mn), 1.8790 (Fe), 1.845 (Co), 1.798 Å (Ni). The N-M- N angles are very close to linear for Mn and Fe (179.30 and 179.45°, respectively), but bent for Co and Ni (159.2 and 160.90°, respectively). As expected, the d⁵ Mn complex has a magnetic moment of 5.53 μΒ that is very close to the spin only value. The EPR spectrum is nearly axial with a low E/D ratio of 0.014. The d⁶ Fe compound has a room temperature magnetic moment of 5.55 μΒ indicative of a large orbital angular momentum contribution. It does not exhibit a Jahn-Teller distortion despite the expected doubly degenerate ground state. Applied field Mössbauer spectroscopy shows that the effective internal hyperfine field is unusually large, Hint = 105 T. The magnetic moments of Co[N(t-Bu)₂]₂ and Ni[N(t-Bu)₂]₂ are 5.24 and 3.02 μΒ respectively. Both are EPR silent at 4.2 K. Treatment of TiCl₄ with three equivalents of LiN(t-Bu)2 in pentane affords the briding imido compound Ti₂[μ-N(t-Bu)]₂Cl₂[N(t-Bu)₂]₂ via a dealkylation reaction. Rotation around the bis(tert-butyl)amido groups is hindered, with activation parameters of ΔH‡ = 12.8 ± 0.6 kcal mol-1 and ΔS‡ = -8 ± 2 cal K-1 ·mol-1, as evidenced by variable temperature 1H NMR spectroscopy. Treatment of TiCl₄ with two equivalents of HN(t-Bu)₂ affords Ti₂Cl₆[N(t-Bu)₂]₂. This complex shows a close-contact of 2.634(3) Å between Ti and the carbon atom of one of the CH₃ substituents on the tert-butyl groups. Theoretical considerations and detailed structural comparisons suggest this interaction is not agostic in nature, but rather is a consequence of interligand repulsions. Treatment of NiI₂(PPh3)₂ and PdCl₂(PPh₃)₂ with LiN(t-Bu)₂in benzene affords Ni[N(t-Bu)₂](PPh₃)I and Pd₃(μ₂-NBut₂)2(μ₂-PPh₂)Ph(PPh₃) respectively. The compound Ni[N(t-Bu)₂](PPh₃)I has distorted T-shape in geometry, whereas Pd₃(μ₂-NBut₂)₂(μ₂-PPh₂)Ph(PPh₃) contains a triangular palladium core. Manganese nitride films were grown from Mn[N(t-Bu)₂]₂ in the presence of anhydrous ammonia. The growth rate was several nanometers per minute even at the remarkably low temperature of 80⁰C. As grown, the films are carbon- and oxygen-free, and have a columnar morphology. The spacings between the columns become smaller and the films become smoother as the growth temperature is increased. The composition of the films is consistent with a stoichiometry of Mn₅N₂.

Host-guest chemistry of solid coordination frameworks (SCFs) based on Copper(II)-Pyridine Ligands

283 p.

Phenolic compounds in Coleostephus myconis (L.) Rchb.f.: characterization by HPLC-DAD-ESI/MS and phenology effects

The Asteraceae family is spread worldwide. In Portugal, there are more than 300 species, standing out as one of the botanical families with largest representation in the Portuguese flora. Coleostephus myconis (L.) Rchb.f. is a scarcely studied Asteraceae species, characterized as having ruderal growth and persistence in abandoned soils (an expanding problem due to the desertification phenomena in rural areas). In this work, the flowers of C. myconis were collected in three different flowering stages (i: flower bud; ii: flower in anthesis; iii: senescent flower) from the Northwestern area of the Portuguese territory. Powdered samples (1 g) were extracted twice with ethanol:water 50:50 (v/v). After removing solvents, the combined extracts were re-dissolved, filtered through 0.22-μm disposable LC filter disks and analyzed by high performance liquid chromatography coupled to a diode array detector and electrospray ionization-mass spectrometry (HPLC-DAD/ESI-MS). The phenolic compounds were characterized according to their UV and mass spectra, and retention times. For the quantitative analysis, calibration curves of standard compounds were used. According to the UV spectra (λmax = 314-330 nm) and pseudomolecular ions ([M-H]-) at m/z 353 and 515, all producing an m/z 191 ion, four compounds derived from quinic acid were detected: 3-O-caffeoylquinic acid (Figure 1A), 5-O-caffeoylquinic acid (Figure 1B), 3,5-O-dicaffeoylquinic acid (Figure 1C) and 4,5-O-dicaffeoylquinic acid (Figure 1D), as also supported by the literature [1,2]. A fifth phenolic acid was identified as protocatechuic acid. The detected flavonoid were quercetin-O-glucuronide, quercetin-3-Oglucoside, myricetin-O-methyl-hexoside and a second glycosylated myricetin (not possible to identify completely). Some statistically significant changes were detected among the different assayed flowering stages; nevertheless, 3,5-O-dicaffeoylquinic acid was the major compound, independently of the phenologic stage. According to the previous results, C. myconis might be considered as a potential natural source of these valuable bioactive compounds, especially considering the high botanical representativeness of this plant and its inexpensiveness.

Comprendre et maîtriser le passage de type I à type II de puits quantiques d'In(x)Ga(1-x)As(y)Sb(1-y) sur substrat de GaSb

Les antimoniures sont des semi-conducteurs III-V prometteurs pour le développement de dispositifs optoélectroniques puisqu'ils ont une grande mobilité d'électrons, une large gamme spectrale d'émission ou de détection et offrent la possibilité de former des hétérostructures confinées dont la recombinaison est de type I, II ou III. Bien qu'il existe plusieurs publications sur la fabrication de dispositifs utilisant un alliage d'In(x)Ga(1-x)As(y)Sb(1-y) qui émet ou détecte à une certaine longueur d'onde, les détails, à savoir comment sont déterminés les compositions et surtout les alignements de bande, sont rarement explicites. Très peu d'études fondamentales sur l'incorporation d'indium et d'arsenic sous forme de tétramères lors de l'épitaxie par jets moléculaires existent, et les méthodes afin de déterminer l'alignement des bandes des binaires qui composent ces alliages donnent des résultats variables. Un modèle a été construit et a permis de prédire l'alignement des bandes énergétiques des alliages d'In(x)Ga(1-x)As(y)Sb(1-y) avec celles du GaSb pour l'ensemble des compositions possibles. Ce modèle tient compte des effets thermiques, des contraintes élastiques et peut aussi inclure le confinement pour des puits quantiques. De cette manière, il est possible de prédire la transition de type de recombinaison en fonction de la composition. Il est aussi montré que l'indium ségrègue en surface lors de la croissance par épitaxie par jets moléculaires d'In(x)Ga(1-x)Sb sur GaSb, ce qui avait déjà été observé pour ce type de matériau. Il est possible d'éliminer le gradient de composition à cette interface en mouillant la surface d'indium avant la croissance de l'alliage. L'épaisseur d'indium en surface dépend de la température et peut être évaluée par un modèle simple simulant la ségrégation. Dans le cas d'un puits quantique, il y aura une seconde interface GaSb sur In(x)Ga(1-x)Sb où l'indium de surface ira s'incorporer. La croissance de quelques monocouches de GaSb à basse température immédiatement après la croissance de l'alliage permet d'incorporer rapidement ces atomes d'indium et de garder la seconde interface abrupte. Lorsque la composition d'indium ne change plus dans la couche, cette composition correspond au rapport de flux d'atomes d'indium sur celui des éléments III. L'arsenic, dont la source fournit principalement des tétramères, ne s'incorpore pas de la même manière. Les tétramères occupent deux sites en surface et doivent interagir par paire afin de créer des dimères d'arsenic. Ces derniers pourront alors être incorporés dans l'alliage. Un modèle de cinétique de surface a été élaboré afin de rendre compte de la diminution d'incorporation d'arsenic en augmentant le rapport V/III pour une composition nominale d'arsenic fixe dans l'In(x)Ga(1-x)As(y)Sb(1-y). Ce résultat s'explique par le fait que les réactions de deuxième ordre dans la décomposition des tétramères d'arsenic ralentissent considérablement la réaction d'incorporation et permettent à l'antimoine d'occuper majoritairement la surface. Cette observation montre qu'il est préférable d'utiliser une source de dimères d'arsenic, plutôt que de tétramères, afin de mieux contrôler la composition d'arsenic dans la couche. Des puits quantiques d'In(x)Ga(1-x)As(y)Sb(1-y) sur GaSb ont été fabriqués et caractérisés optiquement afin d'observer le passage de recombinaison de type I à type II. Cependant, celui-ci n'a pas pu être observé puisque les spectres étaient dominés par un niveau énergétique dans le GaSb dont la source n'a pu être identifiée. Un problème dans la source de gallium pourrait être à l'origine de ce défaut et la résolution de ce problème est essentielle à la continuité de ces travaux.

Determination of the cytotoxic capacity of organotin compounds derivatives from salicylidene benzoylhidrazone

The successful application of metal complexes in the treatment of many diseases, including cancer, is a rapidly expanding area in biomedical chemistry and research. Organotin compounds studies show the versatility and the attractive features of these molecules. In the same manner, has been reported the development of new compounds derivative from bezoylhidrazones, which possess the azomethine fragment (-N = CH-), key pillar for designing new drugs with biological activity. Based on the above, we are interested in to synthesize four tin compounds derivatives from benzoylhidrazones, and the evaluation of their cytotoxic capacity. Conclusions and contribution: In this research work, we reported four new tin compounds derivatives from bezoylhidrazones, which were characterized by spectroscopic and spectrometric techniques and X-ray diffraction In the same manner, cytotoxic ability of each compound was studied and reported and compared with metaled base drugs like cisplatin and carboplatin. Also, in some cases it was possible to use their luminescent ability to study their intracellular behavior.

Adsorção de Pb(II) utilizando adsorvente composto por montmorilonita e dolomita

The destructive impact of improper disposal of heavy metals in the environment increases as a direct result of population explosion, urbanization and industrial expansion and technological developments. Argil are potential materials for adsorption of inorganic and the pelletization of it is required for use in adsorptive columns of fixed bed. The low cost and the possibility of regeneration makes these materials attractive for use in the purification process, capable of removing inorganic compounds in contaminated aquatic environments. In this work was made pellets of a mixture of dolomite and montmorillonite by wet agglomeration, in different percentages. The removal of Pb (II) was investigated through experimental studies, and was modeled by kinetic models and isotherms of adsorption. The materials were characterized using the techniques of XRD, TG / DTA, FT-IR, and surface area by BET method. The results showed the adsorption efficiency of the contaminant by the composite material studied in synthetic solution. The study found that the adsorption follows the Langmuir model, and the kinetics of adsorption follows the model of pseudosecond order

Antifungal activity of extracts from Atacama Desert fungi against Paracoccidioides brasiliensis and identification of Aspergillus felis as a promising source of natural bioactive compounds

Fungi of the genus Paracoccidioides are responsible for paracoccidioidomycosis. The occurrence of drug toxicity and relapse in this disease justify the development of new antifungal agents. Compounds extracted from fungal extract have showing antifungal activity. Extracts of 78 fungi isolated from rocks of the Atacama Desert were tested in a microdilution assay against Paracoccidioides brasiliensis Pb18. Approximately 18% (5) of the extracts showed minimum inhibitory concentration (MIC) values ≤ 125.0 μg/mL. Among these, extract from the fungus UFMGCB 8030 demonstrated the best results, with an MIC of 15.6 μg/mL. This isolate was identified as Aspergillus felis (by macro and micromorphologies, and internal transcribed spacer, β-tubulin, and ribosomal polymerase II gene analyses) and was grown in five different culture media and extracted with various solvents to optimise its antifungal activity. Potato dextrose agar culture and dichloromethane extraction resulted in an MIC of 1.9 μg/mL against P. brasiliensis and did not show cytotoxicity at the concentrations tested in normal mammalian cell (Vero). This extract was subjected to bioassay-guided fractionation using analytical C18RP-high-performance liquid chromatography (HPLC) and an antifungal assay using P. brasiliensis. Analysis of the active fractions by HPLC-high resolution mass spectrometry allowed us to identify the antifungal agents present in the A. felis extracts cytochalasins. These results reveal the potential of A. felis as a producer of bioactive compounds with antifungal activity.

Determination of borneol and other chemical compounds of essential oil of Dryobalanops aromatica exudate from Malaysia

Purpose: To determine borneol and other chemical compounds of essential oil derived from the exudate of Dryobalanops aromatica aromatica in Malaysia. Methods: Exudate was collected from D. aromatica and subjected to fractional distillation to obtain essential oil. Gas chromatography-mass spectrometry (GC-MS) was performed to characterize the composition of the isolated essential oil. Results: Essential oil (7.58 %) was obtained with the highest yield (3.24 %) in the first 2 h of fractional distillation. Thirty compounds which accounted for 97.56 % of total essential oil composition were identified by GC-MS, and they include sesquiterpenes (46.87 %), monoterpenes (31.05 %), oxygenated monoterpenes (16.76 %) and oxygenated sesquiterpenes (2.13 %). Borneol (0.74 %) was also detected in the essential oil. Conclusion: Borneol and other terpenoid compounds are present in the essential oil of the exudate of D. aromatica