Punção aspirativa por agulha fina como método de coleta de material para a histopatologia no osteossarcoma canino

Para a obtenção do diagnóstico definitivo do osteossarcoma realizam-se exames citopatológico e histopatológico. O material para exame citopatológico é coletado através de punção aspirativa por agulha fina (PAAF), já para a realização do exame histopatológico é necessário uma amostra de tamanho maior, geralmente conseguida através de biópsia incisional. Este trabalho tem como objetivo desenvolver uma técnica de coleta de material em cães com suspeita de osteossarcoma através de PAAF para a realização de exame histopatológico. Foram coletadas duas amostras de 12 cães suspeitos de osteossarcoma por PAAF. O material obtido pela primeira coleta foi utilizado para confirmar o diagnóstico através do exame citopatológico, enquanto que o material oriundo da segunda coleta foi fixado em formol a 10% para a análise histopatológica. Quatro das 12 amostras (33,3%) avaliadas histopatologicamente pela metodologia proposta obtiveram também o diagnóstico de osteossarcoma. Esses resultados apontam para uma possível adequação da técnica de coleta de material por PAAF para exame histopatológico.

Carbon Nanotubes as Material for Supercapacitor Electrodes

Electrochemical double-layer supercapacitors have an intermediate position between rechargeable batteries, which can store high amounts of energy, and dielectric capacitors, which have high output power. Supercapacitors are widely suggested to be used in automobiles (recuperation during braking, facilitate engine starting, electric stabilization of the system), industry (forklifts, elevators), hybrid off-road machinery and also in consumer electronics. Supercapacitor electrodes require highly porous material. Typically, activated carbon is used. Specific surface area of activated carbon is approximately 1000 m2 per gram. Carbon nanotubes represent one of prospective materials. According to numerous studies this material allows to improve the properties of supercapacitors. The task of this Master‘s Thesis was to test multiwalled carbon nanotubes and become confident with the testing methods.

Hankintatoimen osaamisen kehittäminen

Tutkimuksen tavoitteena oli kuvata sekä määrittää case-yrityksen hankintaosaamisen nykytila. Nykytila-analyysin tarkoituksena oli muodostaa lähtökohdat hankintatoimen kehittämiselle case-yrityksessä. Yksi tavoite oli myös tutkia hankinnan sähköisten työkalujen vaikutusta hankintaosaamiseen. Kirjallisuuden osalta tutkimuksessa hyödynnettiin resurssipohjaisen näkökulmaa sekä dynaamisten kyvykkyyksien lähestymistapaa kuvaamaan hankintaosaamisen sekä -kyvykkyyksien vaikutusta hankintatoimen suorituskykyyn. Empiirisen tutkimuksen aineisto on koottu hyödyntämällä kyselytutkimusta, ryhmähaastattelua sekä puolistrukturoitua haastattelua. Tutkimustulokset kuvaavat laaja-alaisesti case-yrityksen hankintaosaamisen nykytilan sekä hankintatoimen aseman yrityksessä yleisesti. Johtopäätöksissä on nostettu esiin keskeisten tutkimustuloksien lisäksi myös kehittämisen kannalta huomioitavia tekijöitä.

Value added logistics in supply and demand chain : COSTFIX : New operation model for maintenance material logistics in paper industry

This research report illustrates and examines new operation models for decreasing fixed costs and transforming them into variable costs in the field of paper industry. The report illustrates two cases – a new operation model for material logistics in maintenance and an examination of forklift truck fleet outsourcing solutions. Conventional material logistics in maintenance operation is illustrated and some problems related to conventional operation are identified. A new operation model that solves some of these problems is presented including descriptions of procurement and service contracts and sources of added value. Forklift truck fleet outsourcing solutions are examined by illustrating the responsibilities of a host company and a service provider both before and after outsourcing. The customer buys outsourcing services in order to improve its investment productivity. The mechanism of how these services affect the customer company’s investment productivity is illustrated.

Laser-TIG hybrid welding process

Joining processes and techniques need to meet the trend of new applications and the development of new materials. The application in connection with thick and thin plates in industrial fields is wide and the joining technology is in very urgent need. The laser-TIG hybrid welding technology can play the respective advantages of both of them. One major advantage of the hybrid laser-TIG welding technology is its efficient use of laser energy. Additionally, it can develop into a high and new advanced welding technology and become a hot spot in both the application and research area. This thesis investigated laser –TIG hybrid welding with the aim of enlightening the reader on its advantages, disadvantages and future areas of improvement. The main objective is to investigate laser-TIG hybrid on the welding of various metals (steels, magnesium, aluminium etc.). In addition, it elaborates on various possible combinations on hybrid laser-TIG welding technology and their benefits. The possibility of using laser-TIG hybrid in welding of thick materials was investigated. The method applied in carrying out this research is by using literature review. The results showed that hybrid laser-TIG is applicable to almost all weldable metals. Also it proves to be effective in welding refractive metals. The possibility of welding with or without filler materials is of economic advantage especially in welding of materials with no filler material. Thick plate’s hybrid laser-TIG welding is showing great prospects although it normally finds its used in welding thin materials in the range of 0.4 to 0.8 mm. The findings show that laser-TIG hybrid welding can be a versatile welding process and therefore will be increasingly used industrially due to its numerous advantages and the development of new TIG arc that enhances its capabilities.

Enhancing the development of military capabilities by a systems approach

The political environment of security and defence has changed radically in the Western industrialised world since the Cold War. As a response to these changes, since the beginning of the twenty-first century, most Western countries have adopted a ‘capabilities-based approach’ to developing and operating their armed forces. More responsive and versatile military capabilities must be developed to meet the contemporary challenges. The systems approach is seen as a beneficial means of overcoming traps in resolving complex real -world issues by conventional thinking. The main objectives of this dissertation are to explore and assess the means to enhance the development of military capabilities both in concept development and experimentation (CD&E) and in national defence materiel collaboration issues. This research provides a unique perspective, a systems approach, to the development areas of concern in resolving complex real-world issues. This dissertation seeks to increase the understanding of the military capability concept both as a whole and with in its life cycle. The dissertation follows the generic functionalist systems methodology by Jackson. The methodology applies a comprehensive set of constitutive rules to examine the research objectives. This dissertation makes contribution to current studies about military capability. It presents two interdepen dent conceptual capability models: the comprehensive capability meta-model (CCMM) and the holistic capability life cycle model (HCLCM). These models holistically and systematically complement the existing, but still evolving, understanding of military capability and its life cycle. In addition, this dissertation contributes to the scientific discussion of defence procurement in its broad meaning by introducing the holistic model about the national defence materiel collaboration between the defence forces, defence industry and academia. The model connects the key collaborative mechanisms, which currently work in isolation from each other, and take into consideration the unique needs of each partner. This dissertation contributes empirical evidence regarding the benefits of enterprise architectures (EA) to CD&E. The EA approach may add value to traditional concept development by increasing the clarity, consistency and completeness of the concept. The most important use considered for EA in CD&E is that it enables further utilisation of the concept created in the case project.

Fast pyrolysis in circulating fluidized bed: feasibility study

Today the limitedness of fossil fuel resources is clearly realized. For this reason there is a strong focus throughout the world on shifting from fossil fuel based energy system to biofuel based energy system. In this respect Finland with its proven excellent forestry capabilities has a great potential to accomplish this goal. It is regarded that one of the most efficient ways of wood biomass utilization is to use it as a feedstock for fast pyrolysis process. By means of this process solid biomass is converted into liquid fuel called bio-oil which can be burnt at power plants, used for hydrogen generation through a catalytic steam reforming process and as a source of valuable chemical compounds. Nowadays different configurations of this process have found their applications in several pilot plants worldwide. However the circulating fluidized bed configuration is regarded as the one with the highest potential to be commercialized. In the current Master’s Thesis a feasibility study of circulating fluidized bed fast pyrolysis process utilizing Scots pine logs as a raw material was conducted. The production capacity of the process is 100 000 tonne/year of bio-oil. The feasibility study is divided into two phases: a process design phase and economic feasibility analysis phase. The process design phase consists of mass and heat balance calculations, equipment sizing, estimation of pressure drops in the pipelines and development of plant layout. This phase resulted in creation of process flow diagrams, equipment list and Microsoft Excel spreadsheet that calculates the process mass and heat balances depending on the bio-oil production capacity which can be set by a user. These documents are presented in the current report as appendices. In the economic feasibility analysis phase there were at first calculated investment and operating costs of the process. Then using these costs there was calculated the price of bio-oil which is required to reach the values of internal rate of return of 5%, 10%, 20%, 30%, 40%, and 50%.

Critical aspects on the behavior of material from the mechanical tool-workpiece interaction in single point diamond turning

Some material aspects such as grain size, purity and anisotropy exert an important influence on surface quality, especially in single point diamond turning. The aim of this paper is to present and discuss some critical factors that can limit the accuracy of ultraprecision machining of non-ferrous metals and to identify the effects of them on the cutting mechanism with single point diamond tools. This will be carried out through observations of machined surfaces and chips produced using optical and scanning electron microscopy. Solutions to reduce the influence of some of these limiting factors related with the mechanism of generation of mirror-like surfaces will be discussed.

Potential benefits of building information modeling for building material supplier

This thesis investigated building information modeling (BIM) from a material supplier’s point of view. The objective was to gain understanding about how a building material supplier could benefit from the growing use of BIM in the AEC (architectural, engineering and construction) industry. Increasing amount of inquiries related to BIM from customers and other interest groups had awoken target company’s interest towards BIM. This thesis acts as a pre-study for the target company related to potential of BIM. First of all BIM and its meaning from a material supplier’s point of view was defined based on a literature review. To reveal the potential benefits of BIM for a material supplier a questionnaire survey and in total of 11 interviews were conducted. Based on the literature review and analyzed results it came clear that BIM offers benefits also for material suppliers. Product libraries and material databases for BIM tools can act as an important marketing channel for material suppliers. Material suppliers could also utilize the information from the BIM models to schedule their deliveries more precisely and potentially even to schedule their own production. All this needs deeper cooperation between material suppliers, contractors and other stakeholders in the AEC industry. Based on the results also first steps for the target company to utilize the growing use of BIM were defined.

Wastewater Treatment and Deinking Sludge Utilization Possibilities for Energy and Material Recovery in the Leningrad Region

Operation of pulp and paper mills generates waste including wastewater treatment sludge and deinking sludge. Both sludge types are generated in large amounts and are mainly disposed of in landfills in the Leningrad Region resulting in environmental degradation. The thesis was aimed at seeking new sustainable ways of sludge utilization. Two paper mills operating in the Leningrad Region and landfilling their sludge were identified: “SCA Hygiene Products Russia” and “Knauf”. The former generates 150 t/day of deinking sludge, the latter – 145 t/day of secondary sludge. Chemical analyses of deinking sludge were performed to assess applicability of sludge in construction materials production processes. Higher heating value on dry basis of both sludge types was determined to evaluate energy potential of sludge generated in the Leningrad Region. Total energy output from sludge incineration was calculated. Deinking sludge could be utilized in the production process of “LSR-Cement” or “Slantsy Cement Plant Cesla” factories, and “Pobeda” and “Nikolsky” brick mills without exceeding current sludge management costs.

Unidirectional fiber-reinforced composite as an oral implant abutment material: Experimental studies of E-glass fiber/BisGMA-TEGDMA polymer in vitro

Fiber-reinforced composites (FRCs) are a new group of non-metallic biomaterials showing a growing popularity in many dental and medical applications. As an oral implant material, FRC is biocompatible in bone tissue environment. Soft tissue integration to FRC polymer material is unclear. This series of in vitro studies aimed at evaluating unidirectional E-glass FRC polymer in terms of mechanical, chemical, and biological properties in an attempt to develop a new non-metallic oral implant abutment alternative. Two different types of substrates were investigated: (a) Plain polymer (BisGMA 50%–TEGDMA 50%) and (b) Unidirectional FRC. The mechanical behavior of high fiber-density FRCs was assessed using a three-point bending test. Surface characterization was performed using scanning electron and spinning disk confocal microscopes. The surface wettability/energy was determined using sessile drop method. The blood response, including blood-clotting ability and platelet morphology was evaluated. Human gingival fibroblast cell responses - adhesion kinetics, adhesion strength, and proliferation activity - were studied in cell culture environment using routine test conditions. A novel tissue culture method was developed and used to evaluate porcine gingival tissue graft attachment and growth on the experimental composite implants. The analysis of the mechanical properties showed that there is a direct proportionality in the relationship between E-glass fiber volume fraction and toughness, modulus of elasticity, and load bearing capacity; however, flexural strength did not show significant improvement when high fiber-density FRC is used. FRCs showed moderate hydrophilic properties owing to the presence of exposed glass fibers on the polymer surface. Blood-clotting time was shorter on FRC substrates than on plain polymer. The FRC substrates also showed higher platelet activation state than plain polymer substrates. Fibroblast cell adhesion strength and proliferation rate were highly pronounced on FRCs. A tissue culture study revealed that gingival epithelium and connective tissue established an immediate close contact with both plain polymer and FRC implants. However, FRC seemed to guide epithelial migration outwards from the tissue/implant interface. Due to the anisotropic and hydrophilic nature of FRC, it can be concluded that this material enhances biological events related with soft tissue integration on oral implant surface.

Defining of the material models for stainless steels to be used in FE modeling

The aim of this work is to study the results of tensile tests for austenitic stainless steel type 304 and make accurate FE-models according to the results of the tests. Tensile tests were made at Central Research Institute of Structural Material, Prometey at Saint Petersburg and Mariyenburg in Russia. The test specimens for the tensile tests were produced at Lappeenranta University of Technology in a Laboratory of Steel Structures. In total 4 different tests were made, two with base material specimens and two with transverse butt weld specimens. Each kind of a specimen was tested at room temperature and at low temperature. By comparing the results of room and low temperature tests of similar test specimen we get to study the results of work hardening that affect the austenitic steels at below room temperature. The produced specimens are to be modeled accurately and then imported for nonlinear FEM- analyzing. Using the data gained from the tensile tests the aim is to get the models work like the specimens did during the tests. By using the analyzed results of the FE-models the aim is to calculate and get the stress-strain curves that correspond to the results acquired from the tensile tests.

Optimization of parameters for fiber laser-MAG hybrid welding in shipbuilding applications

The Arctic region becoming very active area of the industrial developments since it may contain approximately 15-25% of the hydrocarbon and other valuable natural resources which are in great demand nowadays. Harsh operation conditions make the Arctic region difficult to access due to low temperatures which can drop below -50 °C in winter and various additional loads. As a result, newer and modified metallic materials are implemented which can cause certain problems in welding them properly. Steel is still the most widely used material in the Arctic regions due to high mechanical properties, cheapness and manufacturability. Moreover, with recent steel manufacturing development it is possible to make up to 1100 MPa yield strength microalloyed high strength steel which can be operated at temperatures -60 °C possessing reasonable weldability, ductility and suitable impact toughness which is the most crucial property for the Arctic usability. For many years, the arc welding was the most dominant joining method of the metallic materials. Recently, other joining methods are successfully implemented into welding manufacturing due to growing industrial demands and one of them is the laser-arc hybrid welding. The laser-arc hybrid welding successfully combines the advantages and eliminates the disadvantages of the both joining methods therefore produce less distortions, reduce the need of edge preparation, generates narrower heat-affected zone, and increase welding speed or productivity significantly. Moreover, due to easy implementation of the filler wire, accordingly the mechanical properties of the joints can be manipulated in order to produce suitable quality. Moreover, with laser-arc hybrid welding it is possible to achieve matching weld metal compared to the base material even with the low alloying welding wires without excessive softening of the HAZ in the high strength steels. As a result, the laser-arc welding methods can be the most desired and dominating welding technology nowadays, and which is already operating in automotive and shipbuilding industries with a great success. However, in the future it can be extended to offshore, pipe-laying, and heavy equipment industries for arctic environment. CO2 and Nd:YAG laser sources in combination with gas metal arc source have been used widely in the past two decades. Recently, the fiber laser sources offered high power outputs with excellent beam quality, very high electrical efficiency, low maintenance expenses, and higher mobility due to fiber optics. As a result, fiber laser-arc hybrid process offers even more extended advantages and applications. However, the information about fiber or disk laser-arc hybrid welding is very limited. The objectives of the Master’s thesis are concentrated on the study of fiber laser-MAG hybrid welding parameters in order to understand resulting mechanical properties and quality of the welds. In this work only ferrous materials are reviewed. The qualitative methodological approach has been used to achieve the objectives. This study demonstrates that laser-arc hybrid welding is suitable for welding of many types, thicknesses and strength of steels with acceptable mechanical properties along very high productivity. New developments of the fiber laser-arc hybrid process offers extended capabilities over CO2 laser combined with the arc. This work can be used as guideline in hybrid welding technology with comprehensive study the effect of welding parameter on joint quality.

Making the impact on research and society : a case study: crowdsourcing solutions developed for the linguistic research and citizen science

Can crowdsourcing solutions serve many masters? Can they be beneficial for both, for the layman or native speakers of minority languages on the one hand and serious linguistic research on the other? How did an infrastructure that was designed to support linguistics turn out to be a solution for raising awareness of native languages? Since 2012 the National Library of Finland has been developing the Digitisation Project for Kindred Languages, in which the key objective is to support a culture of openness and interaction in linguistic research, but also to promote crowdsourcing as a tool for participation of the language community in research. In the course of the project, over 1,200 monographs and nearly 111,000 pages of newspapers in Finno-Ugric languages will be digitised and made available in the Fenno-Ugrica digital collection. This material was published in the Soviet Union in the 1920s and 1930s, and users have had only sporadic access to the material. The publication of open-access and searchable materials from this period is a goldmine for researchers. Historians, social scientists and laymen with an interest in specific local publications can now find text materials pertinent to their studies. The linguistically-oriented population can also find writings to delight them: (1) lexical items specific to a given publication, and (2) orthographically-documented specifics of phonetics. In addition to the open access collection, we developed an open source code OCR editor that enables the editing of machine-encoded text for the benefit of linguistic research. This tool was necessary since these rare and peripheral prints often include already archaic characters, which are neglected by modern OCR software developers but belong to the historical context of kindred languages, and are thus an essential part of the linguistic heritage. When modelling the OCR editor, it was essential to consider both the needs of researchers and the capabilities of lay citizens, and to have them participate in the planning and execution of the project from the very beginning. By implementing the feedback iteratively from both groups, it was possible to transform the requested changes as tools for research that not only supported the work of linguistics but also encouraged the citizen scientists to face the challenge and work with the crowdsourcing tools for the benefit of research. This presentation will not only deal with the technical aspects, developments and achievements of the infrastructure but will highlight the way in which user groups, researchers and lay citizens were engaged in a process as an active and communicative group of users and how their contributions were made to mutual benefit.

Uuden tiedon hankinta ja hyödyntäminen organisaation innovaatioprosesseissa

Tämän tutkimuksen tavoitteena oli tutkia, miten uuden ja erityisesti tulevaisuuteen suuntautuvan tiedon hankintaa ja hyödyntämistä organisaatioiden innovaatioprosesseissa voidaan tarkastella ja jäsentää sekä kehittää avoimen innovaatioteorioiden pohjalta. Tulevaisuustiedon järjestelmällinen hyödyntäminen on yhä tärkeämmässä asemassa 2010-luvun organisaatioiden innovatiivisuuden ja kilpailukyvyn kannalta. Tämä on abstraktin luonteensa vuoksi erittäin haasteellista mutta teoriassa mahdollista, jos uuden tiedon liittämisestä organisaation käyttöön on tehty tärkeä ja selkeä osa koko organisaation strategiaa. Uuden tiedon tehokkaaseen käsittelemiseen ja siirtämiseen organisaatiossa tarvitaan suunnitelmallista ennakointitoimintaa, sosiaalisia sovittelumekanismeja ja rakentavaa yhteistyötä myös ulkopuolisten toimijoiden kanssa. Valitun teoriakehyksen pohjalta laadittiin yksinkertaistettu kyselytutkimus, johon oli liitetty absorptiiviseen kapasiteettiin, visionääriseen kyvykkyyteen, ennakointitoimintaan ja uuden tiedon käsittelyyn liittyviä käsitteitä. Kyselyn tarkoituksena oli myös tarjota organisaatiolle mahdollisuus tarkastella nykyistä tilaansa uuden tiedon monivaiheisen hyödyntämisen kannalta. Kyselytutkimus lähetettiin suomalaisille teollisuusyrityksille ja saatuja vastauksia käytettiin empiirisenä aineistona. Empiiristä aineistoa tarkasteltiin kvantitatiivisin menetelmän ja tuloksista saatiin hyödyllistä tietoa yritysten toiminnasta käytännöntasolta.