Methyl ester preparation from peanut oil and its effect on DI diesel engine combustion

This study investigated the preparation of methyl ester (Biodiesel) from peanut oil by transesterification method and its effect on DI diesel engine. Two parameters were measured during the engine operation: one is engine performance (brake thermal efficiency and brake specific fuel consumption), and the other is the exhaust emissions (NOx and CO). The result showed that, when compared with neat diesel fuel, the brake thermal efficiency of biodiesel blend was almost similar or a slight lower. However, brake specific fuel consumption (bsfc) was a little higher than neat diesel. CO was lower and NOx was little higher with biodiesel blend than that of diesel. The engine performance for B10 and B20 was very similar. At medium and high load conditions the engine emissions for B10 and B20 has no significant variation. Hence, B20 can safely be used in diesel engine without any significant penalty in engine performance and emissions.

Infrared study of CO, CO2, H2 and H2O interactions on potassium-promoted reduced and oxidised silica-supported copper catalysts

FTIR spectra are reported of CO, CO2, H2 and H2O on silica-supported potassium, copper and potassium-copper catalysts. Adsorption of CO on a potassium/silica catalyst resulted in the formation of complexed CO moieties. Whereas exposure of CO2 to the same catalyst produced bands ascribed to CO2 -, bidentate carbonate and complexed CO species. Fully oxidised copper/silica surfaces gave bands due to CO on CuO and isolated Cu2+ cations on silica. Addition of potassium to this catalyst removed a peak attributed to CO adsorption on isolated Cu2+ cations and red-shifted the maximum ascribed to CO adsorbed on CuO. For a reduced copper/silica catalyst bands due to adsorbed CO on both high and low index planes were red-shifted by 10 cm-1 in the presence of potassium, although the strength of the Cu - CO bond did not appear to be increased concomitantly. An explanation in terms of an electrostatic effect between potassium and adsorbed CO is forwarded. A small maximum at ca. 1510 cm-1 for the reduced catalyst increased substantially upon exposing CO to a reoxidised promoted catalyst. Correspondingly, CO2 adsorption allowed the identification of two distinct carboxylate species, one of which was located at an interfacial site between copper and potassium oxide. Carboxylate species reacted with hydrogen at 295 K, on a reduced copper surface, to produce predominantly unidentate formate on potassium. In contrast no interaction was detected on a reoxidised copper catalyst at 295 K until a fraction of the copper surface was in a reduced state. Furthermore the interaction of polar water molecules with carboxylate species resulted in a perturbation of this structure which gave lower C----O stretching frequencies.

Modeling the co-precipitation of silica and calcium oxalate in sugar solutions

Solution chemistry plays a significant role in the rate and type of foulant formed on heated industrial surfaces. This paper describes the effect of sucrose, silica (SiO2), Ca2+ and Mg2+ ions, and trans-aconitic acid on the kinetics and solubility of SiO2 and calcium oxalate monohydrate (COM) in mixed salt solutions containing sucrose and refines models previously proposed. The developed SiO2 models show that sucrose and SiO2 concentrations are the main parameters that determine apparent order (n) and apparent rate of reaction (k) and SiO2 solubility over a 24 h period. The calcium oxalate solubility model shows that while increasing [Mg2+] increases COM solubility, the reverse is so with increasing sucrose concentrations. The role of solution species on COM crystal habit is discussed and the appearance of the uncommon (001) face is explained.

Geometric sensitivity of patient-specific finite element models of the spine to variability in user-selected anatomical landmarks

Software to create individualised finite element (FE) models of the osseoligamentous spine using pre-operative computed tomography (CT) data-sets for spinal surgery patients has recently been developed. This study presents a geometric sensitivity analysis of this software to assess the effect of intra-observer variability in user-selected anatomical landmarks. User-selected landmarks on the osseous anatomy were defined from CT data-sets for three scoliosis patients and these landmarks were used to reconstruct patient-specific anatomy of the spine and ribcage using parametric descriptions. The intra-observer errors in landmark co-ordinates for these anatomical landmarks were calculated. FE models of the spine and ribcage were created using the reconstructed anatomy for each patient and these models were analysed for a loadcase simulating clinical flexibility assessment. The intra-observer error in the anatomical measurements was low in comparison to the initial dimensions, with the exception of the angular measurements for disc wedge and zygapophyseal joint (z-joint) orientation and disc height. This variability suggested that CT resolution may influence such angular measurements, particularly for small anatomical features, such as the z-joints, and may also affect disc height. The results of the FE analysis showed low variation in the model predictions for spinal curvature with the mean intra-observer variability substantially less than the accepted error in clinical measurement. These findings demonstrate that intra-observer variability in landmark point selection has minimal effect on the subsequent FE predictions for a clinical loadcase.

Limitation of Actions - effect of admission of liability

The decision in Simpson v Lenton [2002] QDC 214 applied the decisions of the Court of Appeal in Lindsay v Smith [2002] 1 Qd R 610 and Morris v FAI General Insurance Co Ltd [1996] 1 QDR 495 in finding the second defendant, having admitted liability, was estopped from relying on the expiration of the limitation period.

Catalytic role of pre-adsorbed CO in platinum-based catalysts : the reduction of SO 2 by CO on Pt l Au m (CO) n

Using density functional theory, we have investigated the catalytic properties of bimetallic complex catalysts PtlAum(CO)n (l + m = 2, n = 1–3) in the reduction of SO2 by CO. Due to the strong coupling between the C-2p and metal 5d orbitals, pre-adsorption of CO molecules on the PtlAum is found to be very effective in not only reducing the activation energy, but also preventing poisoning by sulfur. As result of the coupling, the metal 5d band is broadened and down-shifted, and charge is transferred from the CO molecules to the PtlAum. As SO2 is adsorbed on the catalyst, partial charge moves to the anti-σ bonding orbitals between S and O in SO2, weakening the S–O bond strength. This effect is enhanced by pre-adsorbing up to three CO molecules, therefore the S–O bonds become vulnerable. Our results revealed the mechanism of the excellent catalytic properties of the bimetallic complex catalysts.

Furan containing diketopyrrolopyrrole copolymers : synthesis, characterization, organic field effect transistor performance and photovoltaic properties

In this work, we report design, synthesis and characterization of solution processable low band gap polymer semiconductors, poly{3,6-difuran-2-yl-2,5-di(2- octyldodecyl)-pyrrolo[3,4-c]pyrrole-1,4-dione-alt-phenylene} (PDPP-FPF), poly{3,6-difuran-2-yl-2,5-di(2-octyldodecyl)-pyrrolo[3,4-c]pyrrole-1, 4-dione-alt-naphthalene} (PDPP-FNF) and poly{3,6-difuran-2-yl-2,5-di(2- octyldodecyl)-pyrrolo[3,4-c]pyrrole-1,4-dione-alt-anthracene} (PDPP-FAF) using the furan-containing 3,6-di(furan-2-yl)pyrrolo[3,4-c]pyrrole-1,4(2H,5H)-dione (DBF) building block. As DBF acts as an acceptor moiety, a series of donor-acceptor (D-A) copolymers can be generated when it is attached alternatively with phenylene, naphthalene or anthracene donor comonomer blocks. Optical and electrochemical characterization of thin films of these polymers reveals band gaps in the range of 1.55-1.64 eV. These polymers exhibit excellent hole mobility when used as the active layer in organic thin-film transistor (OTFT) devices. Among the series, the highest hole mobility of 0.11 cm 2 V -1 s -1 is achieved in bottom gate and top-contact OTFT devices using PDPP-FNF. When these polymers are used as a donor and [70]PCBM as the acceptor in organic photovoltaic (OPV) devices, power conversion efficiencies (PCE) of 2.5 and 2.6% are obtained for PDPP-FAF and PDPP-FNF polymers, respectively. Such mobility values in OTFTs and performance in OPV make furan-containing DBF a very promising block for designing new polymer semiconductors for a wide range of organic electronic applications.

Isoindigo dye incorporated copolymers with naphthalene and anthracene: promising materials for stable organic field effect transistors

In this paper, we report the design and synthesis of isoindigo based low band gap polymer semiconductors, poly{N,N′-(2-octyldodecyl)-isoindigo-alt- naphthalene} (PISD-NAP) and poly{N,N′-(2-octyldodecyl)-isoindigo-alt- anthracene} (PISD-ANT). A series of donor-acceptor (D-A) copolymers can be prepared where donor and acceptor conjugated blocks can be attached alternately using organometallic coupling. In these polymers, an isoindigo dye acceptor moiety has been attached alternately with naphthalene and anthracene donor comonomer blocks by Suzuki coupling. PISD-NAP and PISD-ANT exhibit excellent solution processibility and good film-forming properties. Gel permeation chromatography exhibits a higher molecular mass with lower polydispersity. UV-vis-NIR absorption of these polymers exhibits a wide absorption band ranging from 300 nm to 800 nm, indicating the low band gap nature of the polymers. Optical band gaps calculated from the solid state absorption cutoff value for PISD-NAP and PISD-ANT are around 1.80 eV and 1.75 eV, respectively. Highest occupied molecular orbital (HOMO) values calculated respectively for PISD-NAP and PISD-ANT thin films on glass substrate by photoelectron spectroscopy in air (PESA) are 5.66 eV and 5.53 eV, indicative of the good stability of these materials in organic electronic device applications. These polymers exhibit p-channel charge transport characteristics when used as the active semiconductor in organic thin-film transistor (OTFT) devices in ambient conditions. The highest hole mobility of 0.013 cm2 V-1 s-1 is achieved in top contact and bottom-gate OTFT devices for PISD-ANT, whereas polymer PISD-NAP exhibited a hole mobility of 0.004 cm2 V -1 s-1. When these polymer semiconductors were used as a donor and PC71BM as an acceptor in OPV devices, the highest power conversion efficiency (PCE) of 1.13% is obtained for the PISD-ANT polymer.

Thiophene-benzothiadiazole-thiophene (D-A-D) based polymers : Effect of donor/acceptor moieties adjacent to D-A-D segment on photophysical and photovoltaic properties

New push-pull copolymers based on thiophene (donor) and benzothiadiazole (acceptor) units, poly[4,7-bis(3-dodecylthiophene-2-yl) benzothiadiazole-co- thiophene] (PT3B1) and poly[4,7-bis(3-dodecylthiophene-2-yl) benzothiadiazole-co-benzothiadiazole] (PT2B2), are designed and synthesized via Stille and Suzuki coupling routes respectively. Gel permeation chromatography shows the number average molecular weights are 31100 and 8400 g mol-1 for the two polymers, respectively. Both polymers have shown absorption throughout a wide range of the UV-vis region, from 300 to 650 nm. A significant red shift of the absorption edge is observed in thin films compared to solution of the copolymers; the optical band gap is in the range of 1.7 to 1.8 eV. Cyclic voltammetry indicates reversible oxidation and reduction processes with HOMO energy levels calculated to be in the range of 5.2 to 5.4 eV. Upon testing both materials for organic field-effect transistors (OFETs), PT3B1 showed a hole mobility of 6.1 × 10-4 cm2 V-1 s -1, while PT2B2 did not show any field effect transport. Both copolymers displayed a photovoltaic response when combined with a methanofullerene as an electron acceptor. The best performance was achieved when the copolymer PT3B1 was blended with [70]PCBM in a 1:4 ratio, exhibiting a short-circuit current of 7.27 mA cm-2, an open circuit voltage of 0.85 V, and a fill factor of 41% yielding a power conversion efficiency of 2.54% under simulated air mass (AM) 1.5 global (1.5 G) illumination conditions (100 mW cm-2). Similar devices utilizing PT2B2 in place of PT3B1 demonstrated reduced performance with a short-circuit current of 4.8 mA cm -2, an open circuit voltage of 0.73 V, and a fill factor of 30% resulting in a power conversion efficiency of roughly 1.06%.

Density of trap states in a polymer field-effect transistor

We report a more accurate method to determine the density of trap states in a polymer field-effect transistor. In the approach, we describe in this letter, we take into consideration the sub-threshold behavior in the calculation of the density of trap states. This is very important since the sub-threshold regime of operation extends to fairly large gate voltages in these disordered semiconductor based transistors. We employ the sub-threshold drift-limited mobility model (for sub-threshold response) and the conventional linear mobility model for above threshold response. The combined use of these two models allows us to extract the density of states from charge transport data much more accurately. We demonstrate our approach by analyzing data from diketopyrrolopyrrole based co-polymer transistors with high mobility. This approach will also work well for other disordered semiconductors in which sub-threshold conduction is important.

The cluster effect in China: Real or imagined?

Policy makers, urban planners and economic geographers readily acknowledge the potential value of industrial clustering. Clusters attract policy makers’ interest because it is widely held that they are a way of connecting agglomeration to innovation and human capital to investment. Urban planners view clustering as a way of enticing creative human capital, the so-called ‘creative class’, that is, creative people are predisposed to live where there is a range of cultural infrastructure and amenities. Economists and geographers have contrived to promote clustering as a solution to stalled regional development. In the People’s Republic of China, over the past decade the cluster has become the default setting of the cultural and creative industries, the latter a composite term applied to the quantifiable outputs of artists, designers and media workers as well as related service sectors such as tourism, advertising and management. The thinking behind many cluster projects is to ‘pick winners’. In this sense the rapid expansion in the number of cultural and creative clusters in China over the past decade is not so very different from the early 1990s, a period that saw an outbreak of innovation parks, most of which inevitably failed to deliver measurable innovation and ultimately served as revenue-generating sources for district governments via real estate speculation. Since the early years of the first decade of the new millennium the cluster model has been pressed into the service of cultural development.

Potential climate effect on Japanese rice productivity

Adaptation to climate change has become an important policy question in recent years. Agriculture is an economic activity that is most sensitive to climate change. We evaluate the dynamic effects of productivity change and individual efforts to adapt to climate change. Adaptation actions in agriculture are evaluated to determine how the climate affects production efficiency. In this paper, we use the bi-directional distance function method to measure Japanese rice production loss due to climate. We find that (1) accumulated precipitation has the greatest effect on rice production efficiency and (2) the climate effect on rice production efficiency decreases over time. Our results empirically support the benefit of the adaptation approach.

The case for unitary taxation with formulary apportionment in the finance sector and the effect on developing nations

In 2013 the OECD released its 15 point Action plan to deal with base erosion and profit shifting (BEPS). In that plan it was recognised that BEPS has a significant effect on developing countries. This is because the lack of tax revenue can lead to a critical underfunding of public investment that would help promote economic growth. To this end, the BEPS project is aimed at ensuring an inclusive approach to take into account not only views of the G20 and OECD countries but also the perspective of developing nations. With this focus in mind and in the context of developing nations, the purpose of this article is to consider a possible solution to profit shifting which occurs under the current transfer pricing regime, with that solution being unitary taxation with formulary apportionment. It does so using the finance sector as a specific case for application. Multinational financial institutions (MNFIs) play a significant role in financing activities of their clients in developing nations. Consistent with the ‘follow-the-client’ phenomenon which explains financial institution expansion, these entities are increasingly profiting from activities associated with this growing market. Further, not only are MNFIs persistent users of tax havens but also, more than other industries, have opportunities to reduce tax through transfer pricing measures. This article establishes a case for an industry specific adoption of unitary taxation with formulary apportionment as a viable alternative to the current regime. It argues that such a model would benefit not only developed nations but also developing nations which are currently suffering the effects of BEPS. In doing so, it considers the practicalities of such an implementation by examining both definitional issues and a possible formula for MNFIs. This article argues that, while there would be implementation difficulties to overcome, the current domestic models of formulary apportionment provide important guidance as to how the unitary business and business activities of MNFIs should be defined as well as factors that should be included in an allocation formula, along with the appropriate weighting. While it would be difficult for developing nations to adopt such a regime, it is argued that it would be no more difficult than addressing issues they face with the current transfer pricing regime. As such, this article concludes that unitary taxation with formulary apportionment is a viable industry specific alternative for MNFIs which would assist developing nations and aid independent fiscal soundness.

The effect of HLA-DR genes on susceptibility to and severity of ankylosing spondylitis

Objective. To analyze the effect of HLA-DR genes on susceptibility to and severity of ankylosing spondylitis (AS). Methods. Three hundred sixty- three white British AS patients were studied; 149 were carefully assessed for a range of clinical manifestations, and disease severity was assessed using a structured questionnaire. Limited HLA class I typing and complete HLA-DR typing were performed using DNA-based methods. HLA data from 13,634 healthy white British bone marrow donors were used for comparison. Results. A significant association between DR1 and AS was found, independent of HLA-B27 (overall odds ratio [OR] 1.4, 95% confidence interval [95% CI] 1.1-1.8, P = 0.02; relative risk [RR] 2.7, 95% CI 1.5-4.8, P = 6 x 10-4 among homozygotes; RR 2.1, 95% CI 1.5-2.8, P = 5 x 10-6 among heterozygotes). A large but weakly significant association between DR8 and AS was noted, particularly among DR8 homozygotes (RR 6.8, 95% CI 1.6-29.2, P = 0.01 among homozygotes; RR 1.6, 95% CI 1.0-2.7, P = 0.07 among heterozygotes). A negative association with DR12 (OR 0.22, 95% CI 0.09-0.5, P = 0.001) was noted. HLA-DR7 was associated with younger age at onset of disease (mean age at onset 18 years for DR7-positive patients and 23 years for DR7-negative patients; Z score 3.21, P = 0.001). No other HLA class I or class H associations with disease severity or with different clinical manifestations of AS were found. Conclusion. The results of this study suggest that HLA-DR genes may have a weak effect on susceptibility to AS independent of HLA-B27, but do not support suggestions that they affect disease severity or different clinical manifestations.

Isostructural co-crystals derived from molecules with different supramolecular topologies

In this article, we report the crystal structures of five halogen bonded co-crystals comprising quaternary ammonium cations, halide anions (Cl– and Br–), and one of either 1,2-, 1,3-, or 1,4-diiodotetrafluorobenzene (DITFB). Three of the co-crystals are chemical isomers: 1,4-DITFB[TEA-CH2Cl]Cl, 1,2-DITFB[TEA-CH2Cl]Cl, and 1,3-DITFB[TEA-CH2Cl]Cl (where TEA-CH2Cl is chloromethyltriethylammonium ion). In each structure, the chloride anions link DITFB molecules through halogen bonds to produce 1D chains propagating with (a) linear topology in the structure containing 1,4-DITFB, (b) zigzag topology with 60° angle of propagation in that containing 1,2-DITFB, and (c) 120° angle of propagation with 1,3-DITFB. While the individual chains have highly distinctive and different topologies, they combine through π-stacking of the DITFB molecules to produce remarkably similar overall arrangements of molecules. Structures of 1,4-DITFB[TEA-CH2Br]Br and 1,3-DITFB[TEA-CH2Br]Br are also reported and are isomorphous with their chloro/chloride analogues, further illustrating the robustness of the overall supramolecular architecture. The usual approach to crystal engineering is to make structural changes to molecular components to effect specific changes to the resulting crystal structure. The results reported herein encourage pursuit of a somewhat different approach to crystal engineering. That is, to investigate the possibilities for engineering the same overall arrangement of molecules in crystals while employing molecular components that aggregate with entirely different supramolecular connectivity.