865 resultados para stage conversion
Resumo:
Centrifugal compressors are widely used for example in refrigeration processes, the oil and gas industry, superchargers, and waste water treatment. In this work, five different vaneless diffusers and six different vaned diffusers are investigated numerically. The vaneless diffusers vary only by their diffuser width, so that four of the geometries have pinch implemented to them. Pinch means a decrease in the diffuser width. Four of the vaned diffusers have the same vane turning angle and a different number of vanes, and two have different vane turning angles. The flow solver used to solve the flow fields is Finflo, which is a Navier-Stokes solver. All the cases are modeled with the Chien's k – έ- turbulence model, and selected cases are modeled also with the k – ώ-SST turbulence model. All five vaneless diffusers and three vaned diffusers are investigated also experimentally. For each construction, the compressor operating map is measured according to relevant standards. In addition to this, the flow fields before and after the diffuser are measured with static and total pressure, flow angle and total temperature measurements. When comparing the computational results to the measured results, it is evident that the k – ώ-SST turbulence model predicts the flow fields better. The simulation results indicate that it is possible to improve the efficiency with the pinch, and according to the numerical results, the two best geometries are the ones with most pinch at the shroud. These geometries have approximately 4 percentage points higher efficiency than the unpinched vaneless diffusers. The hub pinch does not seem to have any major benefits. In general, the pinches make the flow fields before and after the diffuser more uniform. The pinch also seems to improve the impeller efficiency. This is down to two reasons. The major reason is that the pinch decreases the size of slow flow and possible backflow region located near the shroud after the impeller. Secondly, the pinches decrease the flow velocity in the tip clearance, leading to a smaller tip leakage flow and therefore slightly better impeller efficiency. Also some of the vaned diffusers improve the efficiency, the increment being 1...3 percentage points, when compared to the vaneless unpinched geometry. The measurement results confirm that the pinch is beneficial to the performance of the compressor. The flow fields are more uniform with the pinched cases, and the slow flow regions are smaller. The peak efficiency is approximately 2 percentage points and the design point efficiency approximately 4 percentage points higher with the pinched geometries than with the un- pinched geometry. According to the measurements, the two best geometries are the ones with the most pinch at the shroud, the case with the pinch only at the shroud being slightly better of the two. The vaned diffusers also have better efficiency than the vaneless unpinched geometries. However, the pinched cases have even better efficiencies. The vaned diffusers narrow the operating range considerably, whilst the pinch has no significant effect on the operating range.
Resumo:
Currently, public policy has encouraged innovation in universities and also transference of technology to the industry. Another important stage to be considered would be the registration or filing of a patent and the economical viability study. Government programs, such as the innovation incentive program, among others, should facilitate popularization and promote interest by industry. In this work we described the steps, from the conception of the idea to the scale up going through its interest by the industry. The case study is about the glycerol conversion utilizing modified niobia as catalysts.
Resumo:
ABSTRACT We report on the basic properties of zeolite NaY and potassium supported on NaY (K/NaY) assessed by pyrrole-TPD and MBOH transformation. Pyrrole-TPD revealed that impregnation of zeolite NaY with potassium promoted additional adsorption sites for pyrrole compared to parent zeolite. For zeolite with various potassium loadings, pyrrole adsorbed on K/NaY decreased with increased potassium loading. Reduction in pyrrole adsorption could be due to potassium hindering intrinsic basic sites (lattice oxygen), to oxide of potassium occluding in zeolite cavities restricting access for pyrrole, or to K2O reacting with pyrrole to form nondesorbed pyrrolate anions. On MBOH transformation, potassium almost completely suppressed NaY acid sites while K/NaY basicity increased with potassium loading.
Resumo:
It is well known that pH is an important parameter for controlling the eucalyptus pulp bleaching when using the final chlorine dioxide stage, since it affects the effectiveness of the process. Recommendations found in the literature for operating are in the 3.5 to 4.0 range. However, in this paper it was shown that final chlorine dioxide has better performance, with significant brightness gain while also preserving pulp quality, when it is operated at near neutral pH. This result can be explained by the generation of sodium bicarbonate in situ upon adding carbon dioxide at this stage.
Resumo:
Alzheimer`s disease (AD) is characterised neuropathologically by the presence of extracellular amyloid plaques, intraneuronal neurofibrillary tangles, and cerebral neuronal loss. The pathological changes in AD are believed to start even decades before clinical symptoms are detectable. AD gradually affects episodic memory, cognition, behaviour and the ability to perform everyday activities. Mild cognitive impairment (MCI) represents a transitional state between normal aging and dementia disorders, especially AD. The predictive accuracy of the current and commonly used MCI criteria devide this disorder into amnestic (aMCI) and non-amnestic (naMCI) MCI. It seems that many individuals with aMCI tend to convert to AD. However many MCI individuals will remain stable and some may even recover. At present, the principal drugs for the treatment of AD provide only symptomatic and palliative benefits. Safe and effective mechanism-based therapies are needed for this devastating neurodegenerative disease of later life. In conjunction with the development of new therapeutic drugs, tools for early detection of AD would be important. In future one of the challenges will be to detect at an early stage these MCI individuals who will convert to AD. Methods which can predict which MCI subjects will convert to AD will be much more important if the new drug candidates prove to have disease-arresting or even disease–slowing effects. These types of drugs are likely to have the best efficacy if administered in the early or even in the presymptomatic phase of the disease when the synaptic and neuronal loss has not become too widespread. There is no clinical method to determine with certainly which MCI individuals will progress to AD. However there are several methods which have been suggested as predictors of conversion to AD, e.g. increased [11C] PIB uptake, hippocampal atrophy in MRI, low CSF A beta 42 level, high CSF tau-protein level, apolipoprotein E (APOE) ε4 allele and impairment in episodic memory and executive functions. In the present study subjects with MCI appear to have significantly higher [11C] PIB uptake vs healthy elderly in several brain areas including frontal cortex, the posterior cingulate, the parietal and lateral temporal cortices, putamen and caudate. Also results from this PET study indicate that over time, MCI subjects who display increased [11C] PIB uptake appear to be significantly more likely to convert to AD than MCI subjects with negative [11C] PIB retention. Also hippocampal atrophy seems to increase in MCI individuals clearly during the conversion to AD. In this study [11C] PIB uptake increases early and changes relatively little during the AD process whereas there is progressive hippocampal atrophy during the disease. In addition to increased [11C] PIB retention and hippocampal atrophy, the status of APOE ε4 allele might contribute to the conversion from MCI to AD.
Resumo:
It was evaluated the effect of two different sources of local inocula from two contrasting sites (mature forest, pasture) of arbuscular mycorrhizae fungi (AMF) and a non-mycorrhizal control on the plant growth of six woody species differing in functional characteristics (slow-, intermediate- and fast-growth), when introduced in a seasonally tropical dry forest (STDF) converted into abandoned pasture. Six plots (12 X 12m) were set as AMF inoculum source. Six replicates of six different species arranged in a Latin Square design were set in each plot. Plant height, cover area and the number of leaves produced by individual plant was measured monthly during the first growing season in each treatment. Species differed in their ability to benefit from AMF and the largest responsiveness in plant height and leaf production was exhibited by the slow-growing species Swietenia humilis, Hintonia latiflora and Cordia alliodora. At the end of the growing season (November), the plant height of the fast growing species Tabebuia donnel-smithii, Ceiba pentandra and Guazuma ulmifolia were not influenced by AMF. However, inocula of AMF increased leaf production of all plant species regardless the functional characteristics of the species, suggesting a better exploitation of above-ground space and generating a light limited environment under the canopy, which contributed to pasture suppression. Inoculation of seedlings planted in abandoned pasture areas is recommended for ecological restoration due to the high responsiveness of seedling growth in most of species. Use of forest inoculum with its higher diversity of AMF could accelerate the ecological restoration of the above and below-ground comunities.
Resumo:
OBJECTIVES: To correlate the expression of p53 protein and VEGF with the prognosis of patients submitted to curative resection to treat esophageal adenocarcinoma. METHODS: Forty-six patients with esophageal adenocarcinoma, submitted to curative resection, were studied. The expressions of p53 protein and VEGF were assessed by immunohistochemistry in 52.2% and 47.8% of tumors, respectively. RESULTS: P53 protein and VEGF expressions coincided in 26% of the cases, and no correlation between these expressions was observed. None of the clinicopathological factors showed a significant correlation with p53 protein or VEGF expressions. There was no significant association between p53 protein and VEGF expressions and long-term survival. CONCLUSION: The expression of p53 protein and VEGF did not correlate with prognosis in esophageal adenocarcinoma patients submitted to curative resection.
Resumo:
Työn tavoitteenaan oli selvittää suomalaisen lääkejakeluketjun rakenne sekä saada selkeä kuva ketjun toiminnan tehokkuudesta käyttöpääoman sitoutumisen ja kiertoaikojen osalta. Työn alussa käydään läpi teoriaa ja tutkimusta käyttöpääomasta ja sen erien kiertoajoista sekä erityisesti niiden huomioimisesta arvoketjussa. Lisäksi esitellään Suomen lääkemarkkinoiden toimintaa sekä sen toimijoita. Työn empiirinen osa suoritettiin kahdessa päävaiheessa. Ensin analysoitiin Voitto+ -ohjelmasta saatuja valittujen lääkejakeluketjun yritysten julkisia tilinpäätöstietoja ajalta 2005- 2011. Analysointi perustui käyttöpääoman sekä sen erien myyntisaamisten, ostovelkojen ja vaihto-omaisuuden kiertoaikojen laskemiseen. Ketjun yrityksiä vertailtiin toisiinsa ketjun osien keskimääräisten kiertoaikojen osalta ja saatiin selville niiden suhteellinen sijoittuminen toisiinsa nähden. Työn toisessa päävaiheessa haastateltiin esimerkkitoimijaa käsitellyn lääkejakeluketjun jokaisesta osasta: lääketehdas, tukkujakelija ja apteekki. Työssä huomattiin, että käyttöpääoman kiertoaikaan lääkejakeluketjussa vaikuttaa ensisijaisesti ketjun osan toiminnan luonne ja käyttöpääoman hallinnan tehokkuus lääkejakeluketjun toimijoiden välillä vaihtelee osaamisen ja resurssien mukaan. Ketjun eri osissa painottuvat eri käyttöpääoman erät ja ketjun toiminta on optimoitunut aikojen saatossa hyvin stabiiliin tilaan, jota ketjun jäsenillä ei näytä olevan halua muuttaa. Lääkejakeluketjun käyttöpääomaan hallintaa voitaisiin tehostaa varastonhallintaa parantamalla sekä informaation jakamisella saattamalla kysyntätiedot nopeammin koko ketjun tietoon.
Resumo:
Sequestration of carbon dioxide in mineral rocks, also known as CO2 Capture and Mineralization (CCM), is considered to have a huge potential in stabilizing anthropogenic CO2 emissions. One of the CCM routes is the ex situ indirect gas/sold carbonation of reactive materials, such as Mg(OH)2, produced from abundantly available Mg-silicate rocks. The gas/solid carbonation method is intensively researched at Åbo Akademi University (ÅAU ), Finland because it is energetically attractive and utilizes the exothermic chemistry of Mg(OH)2 carbonation. In this thesis, a method for producing Mg(OH)2 from Mg-silicate rocks for CCM was investigated, and the process efficiency, energy and environmental impact assessed. The Mg(OH)2 process studied here was first proposed in 2008 in a Master’s Thesis by the author. At that time the process was applied to only one Mg-silicate rock (Finnish serpentinite from the Hitura nickel mine site of Finn Nickel) and the optimum process conversions, energy and environmental performance were not known. Producing Mg(OH)2 from Mg-silicate rocks involves a two-staged process of Mg extraction and Mg(OH)2 precipitation. The first stage extracts Mg and other cations by reacting pulverized serpentinite or olivine rocks with ammonium sulfate (AS) salt at 400 - 550 oC (preferably < 450 oC). In the second stage, ammonia solution reacts with the cations (extracted from the first stage after they are leached in water) to form mainly FeOOH, high purity Mg(OH)2 and aqueous (dissolved) AS. The Mg(OH)2 process described here is closed loop in nature; gaseous ammonia and water vapour are produced from the extraction stage, recovered and used as reagent for the precipitation stage. The AS reagent is thereafter recovered after the precipitation stage. The Mg extraction stage, being the conversion-determining and the most energy-intensive step of the entire CCM process chain, received a prominent attention in this study. The extraction behavior and reactivity of different rocks types (serpentinite and olivine rocks) from different locations worldwide (Australia, Finland, Lithuania, Norway and Portugal) was tested. Also, parametric evaluation was carried out to determine the optimal reaction temperature, time and chemical reagent (AS). Effects of reactor types and configuration, mixing and scale-up possibilities were also studied. The Mg(OH)2 produced can be used to convert CO2 to thermodynamically stable and environmentally benign magnesium carbonate. Therefore, the process energy and life cycle environmental performance of the ÅAU CCM technique that first produces Mg(OH)2 and the carbonates in a pressurized fluidized bed (FB) were assessed. The life cycle energy and environmental assessment approach applied in this thesis is motivated by the fact that the CCM technology should in itself offer a solution to what is both an energy and environmental problem. Results obtained in this study show that different Mg-silicate rocks react differently; olivine rocks being far less reactive than serpentinite rocks. In summary, the reactivity of Mg-silicate rocks is a function of both the chemical and physical properties of rocks. Reaction temperature and time remain important parameters to consider in process design and operation. Heat transfer properties of the reactor determine the temperature at which maximum Mg extraction is obtained. Also, an increase in reaction temperature leads to an increase in the extent of extraction, reaching a maximum yield at different temperatures depending on the reaction time. Process energy requirement for producing Mg(OH)2 from a hypothetical case of an iron-free serpentine rock is 3.62 GJ/t-CO2. This value can increase by 16 - 68% depending on the type of iron compound (FeO, Fe2O3 or Fe3O4) in the mineral. This suggests that the benefit from the potential use of FeOOH as an iron ore feedstock in iron and steelmaking should be determined by considering the energy, cost and emissions associated with the FeOOH by-product. AS recovery through crystallization is the second most energy intensive unit operation after the extraction reaction. However, the choice of mechanical vapor recompression (MVR) over the “simple evaporation” crystallization method has a potential energy savings of 15.2 GJ/t-CO2 (84 % savings). Integrating the Mg(OH)2 production method and the gas/solid carbonation process could provide up to an 25% energy offset to the CCM process energy requirements. Life cycle inventory assessment (LCIA) results show that for every ton of CO2 mineralized, the ÅAU CCM process avoids 430 - 480 kg CO2. The Mg(OH)2 process studied in this thesis has many promising features. Even at the current high energy and environmental burden, producing Mg(OH)2 from Mg-silicates can play a significant role in advancing CCM processes. However, dedicated future research and development (R&D) have potential to significantly improve the Mg(OH)2 process performance.
Resumo:
In this doctoral thesis, a power conversion unit for a 10 kWsolid oxide fuel cell is modeled, and a suitable control system is designed. The need for research was identified based on an observation that there was no information available about the characteristics of the solid oxide fuel cell from the perspective of power electronics and the control system, and suitable control methods had not previously been studied in the literature. In addition, because of the digital implementation of the control system, the inherent characteristics of the digital system had to be taken into account in the characteristics of the solid oxide fuel cell (SOFC). The characteristics of the solid oxide fuel cell as well the methods for the modeling and control of the DC/DC converter and the grid converter are studied by a literature survey. Based on the survey, the characteristics of the SOFC as an electrical power source are identified, and a solution to the interfacing of the SOFC in distributed generation is proposed. A mathematical model of the power conversion unit is provided, and the control design for the DC/DC converter and the grid converter is made based on the proposed interfacing solution. The limit cycling phenomenon is identified as a source of low-frequency current ripple, which is found to be insignificant when connected to a grid-tied converter. A method to mitigate a second harmonic originating from the grid interface is proposed, and practical considerations of the operation with the solid oxide fuel cell plant are presented. At the theoretical level, the thesis discusses and summarizes the methods to successfully derive a model for a DC/DC converter, a grid converter, and a power conversion unit. The results of this doctoral thesis can also be used in other applications, and the models and methods can be adopted to similar applications such as photovoltaic systems. When comparing the results with the objectives of the doctoral thesis, we may conclude that the objectives set for the work are met. In this doctoral thesis, theoretical and practical guidelines are presented for the successful control design to connect a SOFC-based distributed generation plant to the utility grid.
Ultrasound during the second stage of labour: is it effective to reduce the caesarean section rates?
Resumo:
PURPOSE: To estimate the likelihood of axillary lymph node involvement for patients with early-stage breast cancer, based on a variety of clinical and pathological factors. METHODS: A retrospective analysis was done in hospital databases from 1999 to 2007. Two hundred thirty-nine patients were diagnosed with early-stage breast cancer. Predictive factors, such as patient age, tumor size, lymphovascular invasion, histological grade and immunohistochemical subtype were analyzed to identify variables that may be associated with axillary lymph node metastasis. RESULTS: Patients with tumors that are negative for estrogen receptor, progesterone receptor, and HER2 had approximately a 90% lower chance of developing lymph node metastasis than those with luminal A tumors (e.g., ER+ and/or PR+ and HER2-) - Odds Ratio: 0.11; 95% confidence interval: 0.01-0.88; p=0.01. Furthermore, the risk for lymph node metastasis of luminal A tumors seemed to decrease as patient age increased, and it was directly correlated with tumor size. CONCLUSION: The molecular classification of early-stage breast cancer using immunohistochemistry may help predicting the probability of developing axillary lymph node metastasis. Further studies are needed to optimize predictions for nodal involvement, with the aim of aiding the decision-making process for breast cancer treatment.
Resumo:
Resultaten påvisade små, men mätbara försämringar i minnes- och verbal förmåga hos personer som haft Parkinsons sjukdom under tre år. Jämfört med en kontrollgrupp uppvisade Parkinsonpatienter avvikande responser i hjärnans elektriska aktivitet under en korttidsminnesuppgift, och de presterade även sämre i olika typer av andra minnesuppgifter. Försämring i en specifik typ av minnesuppgift korrelerade med förminskad volym i höger hjärnhalva. Samband hittades också mellan sämre verbal förmåga och förminskad volym i djupa hjärnstrukturer. Förminskad hjärnvolym har tidigare påvisats hos dementa patienter i senare sjukdomsstadier. Forskningsresultaten bidrar med ny kunskap om kognitiva symptom och deras neurala bakgrund vid Parkinsons sjukdom. De tyder också på att tidig kognitiv funktionsnedsättning kan identifieras, vilket kan bidra till utvecklingen av sjukdomens behandling. Parkinsons sjukdom är den näst vanligaste neurogeriatriska sjukdomen efter Alzheimers sjukdom. Symptomen uppstår som följd av förminskad produktion av hjärnans transmittorämne dopamin. Parkinsons sjukdom har traditionellt betraktats som en progressiv motorisk sjukdom. Ny forskning tyder på att multipla hjärnsystem skadas, vilket resulterar i att även tankeprocesser påverkas. 75-80% uppskattas insjukna i demens 10-15 år efter diagnos, men det kognitiva sjukdomsförloppet och orsaken till demenssymptomen är tillsvidare okänd. I Finland uppskattas ca 10-12 000 personer ha Parkinsons sjukdom, varav ca 3 000 uppskattas ha demens. ----------------------------------------------------------------------------------------------------------------------------------------------------- Tutkimuksessa todettiin lieviä muutoksia muisti- ja kielellisissä toiminnoissa alle kolme vuotta sairastaneilla Parkinson-potilailla. Potilailla havaittiin poikkeavia aivosähkötoiminnan vasteita lyhytkestoista muistia mittaavan tehtävän aikana. Potilaat suoriutuivat myös verrokkiryhmää heikommin useissa muistitehtävissä. Heikentynyt tahaton muisti liittyi pienempään aivokuoren harmaan aineen paikalliseen tilavuuteen. Heikompi kielellinen suoriutuminen liittyi pienempään harmaan aineen tilavuuteen aivojen syvissä rakenteissa. Pienentyneitä aivorakenteiden tilavuuksia on aiemmin todettu dementoituneilla Parkinson-potilailla sairauden myöhemmissä vaiheissa. Tutkimustulokset tuovat uutta tietoa Parkinsonin taudin kognitiivisista oireista ja niiden aivoperäisestä taustasta. Tulosten perusteella on mahdollista tunnistaa jo varhaisia kognitiivisia muutoksia, mikä voi mahdollistaa tehokkaamman hoidon kohdentamisen. Parkinsonin tauti on Alzheimerin taudin jälkeen toiseksi yleisin neurogeriatrinen sairaus. Oirekuva liittyy aivojen dopaminergisen järjestelmän rappeutumiseen. Perinteisesti liikehäiriösairaudeksi luokiteltu sairaus vaurioittaa lukuisia muita aivojärjestelmiä aiheuttaen muutoksia myös mm. ajattelutoiminnoissa. Pitkään sairastaneista 75–80 prosentilla esiintyy dementiaoireita, mutta oireiden syy ja kehityskaari tunnetaan toistaiseksi huonosti. Suomessa on arviolta 10–12 000 Parkinson-potilasta, joista noin 3 000 arvioidaan kärsivän dementiaoireista.