Packed bed bioreactor for the isolation and expansion of placental-derived Mesenchymal Stromal Cells

Large numbers of Mesenchymal stem/stromal cells (MSCs) are required for clinical relevant doses to treat a number of diseases. To economically manufacture these MSCs, an automated bioreactor system will be required. Herein we describe the development of a scalable closed-system, packed bed bioreactor suitable for large-scale MSCs expansion. The packed bed was formed from fused polystyrene pellets that were air plasma treated to endow them with a surface chemistry similar to traditional tissue culture plastic. The packed bed was encased within a gas permeable shell to decouple the medium nutrient supply and gas exchange. This enabled a significant reduction in medium flow rates, thus reducing shear and even facilitating single pass medium exchange. The system was optimised in a small-scale bioreactor format (160 cm2) with murine-derived green fluorescent protein-expressing MSCs, and then scaled-up to a 2800 cm2 format. We demonstrated that placental derived MSCs could be isolated directly within the bioreactor and subsequently expanded. Our results demonstrate that the closed system large-scale packed bed bioreactor is an effective and scalable tool for large-scale isolation and expansion of MSCs.

Käsityöläisyyden kuva kultasepän ammatissa : Käsityöläisyys Suomen Kultaseppien Liiton lehdessä 1990-luvun lopussa

The aim of this study is to survey the meaning of craftmanship in goldsmith occupation. The image of craftmanship is built theoretically as well as researcher's own practical experience. The study describes a dialogue between self-employed goldsmith s everyday work and trade union's opinion. Suomen Kultaseppien Liitto (The Goldsmith Assosiation of Finland) was chosen forthe trade union, because it is the biggest, the oldest and the most influential on the occupational area. The research data are volumes 1995 - 1998 of occupational membership journal of Suomen Kultaseppien Liitto. The data analyzed with Adapted Content Analysis and Grounded Theory. The professional occupation of goldsmiths, the role of craftmanship and the future of the occupation are discussed. Additionally, the relationship between the Suomen Kultaseppien Liitto and occupational culture and profession of goldsmiths was studied. Craft and craftmanship is most often discussed in articles related to tradition and education.Craftmanship is understood very idealistically, with little meaning in practical life. St. Eligius and the skill and art of goldsmiths in St Petersburg are raised to symbols of craftmanship. The occupational image is broken and a clear conflict between education and occupation is visible. Education produces artist-craftsmen, while handicraft workers are required in industry, and retailers or specially trained store assistant in business. Computer-aided design and manufacture render handicraft workmanship unnecessary. In a pessimistic view, the future possibilities of the goldsmith occupational profession are dim, because the artist-craftsmen are bound to lose to fast-paced machines. On the other hand, people involved in goldsmith education see the future light, designer-goldsmiths developing the occupational to new dimensions. Suomen Kultaseppien Liitto represents goldsmiths in public. The union, however is governed by non-artisan goldsmiths. The union stresses business attitudes and enterpreneurship, and has succeeded in protecting the privileges of retailers and industry. Goldsmiths profession is seen in the research data as a combination of precious-metal industry, jewellery and watch stores, anda goldsmith shop is considered a specialized giftstore. The goldsmiths occupation is not a profession, and the Suomen Kultaseppien Liitto is not a trade union for artist and craftmen. Accordingly, part of the representative authority of the union could be transferred from the Association to Taidekäsityöläiset Taiko ry, a member of organization of Ornamo. Results of this study show the importance of defining the images of the goldsmith occupational profession and the trade union. The results could be applied to goldsmith education to examine what would be the optimal education and training for present employment opportunities. The important background theories has been the theories of Habermas and Lévi-Strauss.

Design and characterisation of scaffolds for osteochondral regeneration

Treatment of joint diseases such as osteoarthritis is difficult and requires extensive developments for adequate solutions to emerge. Continued innovation in projects explored in this thesis may be beneficial to understanding the requirements of the joint environment. This may then lead to constructs that perform desirably from both mechanical and biological standpoints, resulting in complete, tissue-engineered osteochondral solutions. This thesis investigated specific scaffold designs for bone and osteochondral tissue engineering, as well as the formation of complex criteria on which cartilage hydrogel scaffolds may be assessed. The combination of hydrogels and ceramics were found to maintain chondrogenesis, while the concentration of photoinitiators in photocrosslinkable hydrogel systems may be optimised to maximise mechanical properties and cell viability. Finally, viscoelasticity of hydrogel blends was assessed using oscillatory motion, demonstrating the property is tailorable.

Increased profitability through product diversification and improved sugar quality.

The proposed simplified Integrated Sugar Production Process (ISPP) using membrane technology would allow the sugar industry to produce new product streams and higher quality mill sugar with increased sugar extraction efficiency. Membrane filtration technology has proven to be a technically sound process to increase sugar quality. However commercial viability has been uncertain partly because the benefits to crystallisation and sugar quality have not outweighed the increased processing cost. This simplified ISPP produces additional value-added liquid streams to make the membrane fractionation process more financially viable and improve the profitability of sugar manufacture. An experimental study used pilot scale membrane fractionation of clarified mill juice confirmed the technical feasibility of separating inorganic salt and antioxidant rich fractions from cane juice. The paper presents details on the compositions of the liquid streams along with their potential uses, values and challenges in getting these products out to market.

Application of Mathematical Programming to the Plywood Design and Manufacturing Problem

Plywood manufacture includes two fundamental stages. The first is to peel or separate logs into veneer sheets of different thicknesses. The second is to assemble veneer sheets into finished plywood products. At the first stage a decision must be made as to the number of different veneer thicknesses to be peeled and what these thicknesses should be. At the second stage, choices must be made as to how these veneers will be assembled into final products to meet certain constraints while minimizing wood loss. These decisions present a fundamental management dilemma. Costs of peeling, drying, storage, handling, etc. can be reduced by decreasing the number of veneer thicknesses peeled. However, a reduced set of thickness options may make it infeasible to produce the variety of products demanded by the market or increase wood loss by requiring less efficient selection of thicknesses for assembly. In this paper the joint problem of veneer choice and plywood construction is formulated as a nonlinear integer programming problem. A relatively simple optimal solution procedure is developed that exploits special problem structure. This procedure is examined on data from a British Columbia plywood mill. Restricted to the existing set of veneer thicknesses and plywood designs used by that mill, the procedure generated a solution that reduced wood loss by 79 percent, thereby increasing net revenue by 6.86 percent. Additional experiments were performed that examined the consequences of changing the number of veneer thicknesses used. Extensions are discussed that permit the consideration of more than one wood species.

There is 'hope for you yet': The female drug offender in sentencing discourse

Language and gender research has, in recent years, emphasised the importance of examining the context-specific ways in which people ‘do gender’ in different situations. In this paper, we explore how women involved in drug offences, specifically methamphetamine manufacture offences, are constructed within the language of the courts. Thirty-six sentencing transcripts from the New Zealand courts were examined to investigate how such offences, committed by women, are understood. In order to explore the representation of female offenders, a critical discourse analytic approach was adopted. Such an approach recognises that linguistic modes not only create and legitimise power inequalities but also embody a specific worldview. Three gendered discourses were identified in the sentencing texts: (i) the discourse of femininity, reinforcing the socially prescribed female role; (ii) the discourse of aberration, concerning women who breach traditional gender role expectations, and; (iii) the discourse of salvation, presenting aberrant women with an opportunity to become ‘good’ women once again. The findings illustrate the ways in which processes of gendering take place within a specific community of practice: the courtroom.

Organic diet development for black tiger prawns

The survival and growth of black tiger prawn (Penaeus monodon) juveniles (~3.3 g) were compared after feeding in tanks over one month with several prepared diets based on organically certified ingredients. The extrusion process in the manufacture of pelletised experimental diets was similar to processes used in commercial plants and was closely documented. The daily feeding rate (6% of starting mean body weight) was split equally into two feeds, one in the morning and one in the afternoon. All diets tested produced high survival (97-100%). A widely-used commercial Australian prawn feed was used as a control diet. It contained 41.2% protein with 29.5 g kg-1 lysine, and produced the highest (P<0.05) growth (117% weight gain). Three of the experimental organic diets tested (namely, 1. wheat + soy, 2. pig weaner diet + soy, and 3. pig weaner diet + dried fish waste) produced moderate growth (73–77% weight gain). These contained 33%, 36% or 31% protein, respectively, and produced better (P<0.05) growth than diets utilising a range of other prospective ingredients (eg: wheat + dried scallop gut, wheat + fish waste, wheat + chickpea, or wheat + macadamia meal, containing 23%, 25%, 29% or 24% protein, respectively). An unfed control-treatment produced the lowest (P<0.05) growth (4% weight gain). The water stability of the experimental diets that produced the best growth was poorer than the commercial diet, suggesting that improvements in this aspect of these organic feed’s manufacture could result in additional performance benefits and possibly reduced feed wastage. Analyses revealed a linear relationship between diet performance (in terms of weight gains) and the protein and lysine contents of diets. About 70% of diet performance was explained by these factors. The superior performance of the commercial diet could be attributed primarily to its formulation using mainly marine proteins, as well as a range of other unknown factors (commercial in confidence). These other factors range from use of feed attractants, better knowledge of ingredient nutrient availability, different extrusion conditions and the use of other unspecified micro-nutrients not present in the experimental diets. The organic diets studied still require a degree of fine-tuning before structured commercial uptake. This would sensibly include further detailed investigations of the composition and nutrient availabilities of these and other organic dietary ingredients, and refinement of the extrusion process for formulated diets.

Increased profitability through product diversification and improved sugar quality.

The proposed simplified Integrated Sugar Production Process (ISPP) using membrane technology would allow the sugar industry to produce new product streams and higher quality mill sugar with increased sugar extraction efficiency. Membrane filtration technology has proven to be a technically sound process to increase sugar quality. However commercial viability has been uncertain partly because the benefits to crystallisation and sugar quality have not outweighed the increased processing cost. This simplified ISPP produces additional value-added liquid streams to make the membrane fractionation process more financially viable and improve the profitability of sugar manufacture. An experimental study used pilot scale membrane fractionation of clarified mill juice confirmed the technical feasibility of separating inorganic salt and antioxidant rich fractions from cane juice. The paper presents details on the compositions of the liquid streams along with their potential uses, values and challenges in getting these products out to market. This paper was presented at the 2010 Australian Society of Sugar Cane Technologists annual conference.

Growing organic prawns - in inland saline waters

This report details the results of research into organic production of prawns in Australia. This has involved activities and experiments over two years at several sites and using a multidisciplinary approach. This includes farm trials at an inland demonstration prawn farm which solely utilises saline bore water, sample collection from two commercial prawn farms in coastal regions of south-eastern Queensland, replicated feed trials at one of DPI&F’s aquaculture research stations, specified feed manufacture at the laboratories of University of Queensland, and packaging and product storage trials and food analyses at two of DPI&F’s food technology laboratories. This work was designed to investigate and assist in the possible adoption of organic procedures by the Australian prawn farming industry. The import from Asia of cheaply produced prawns has forced all Australian prawn farmers to review their marketing procedures. Additionally investors are becoming increasingly concerned at the prospects for the expansion of this industry in Australia. Since the competition of seafood products in the marketplace is increasing on a global basis, alternate products are being investigated by those wishing to maintain and/or grow their market share. The premium paid for organic food products would hopefully provide an economic incentive for farmers to convert to organic production systems, with an added advantage that the standards that apply have beneficial implications also for the social and environmental practices of industry.

Fabrication and characterization of plasma polymer thin films from monoterpene alcohols for applications in organic electronics and biotechnology

After more than twenty years of basic and applied research, the use of nanotechnology in the design and manufacture of nanoscale materials is rapidly increasing, particularly in commercial applications that span from electronics across renewable energy areas, and biomedical devices. Novel polymers are attracting significant attention for they promise to provide a low−cost high−performance alternative to existing materials. Furthermore, these polymers have the potential to overcome limitations imposed by currently available materials thus enabling the development of new technologies and applications that are currently beyond our reach. This work focuses on the development of a range of new low−cost environmentally−friendly polymer materials for applications in areas of organic (flexible) electronics, optics, and biomaterials. The choice of the monomer reflects the environmentally−conscious focus of this project. Terpinen−4−ol is a major constituent of Australian grown Melaleuca alternifolia (tea tree) oil, attributed with the oil's antimicrobial and anti−inflammatory properties. Plasma polymerisation was chosen as a deposition technique for it requires minimal use of harmful chemicals and produces no hazardous by−products. Polymer thin films were fabricated under varied process conditions to attain materials with distinct physico−chemical, optoelectrical, biological and degradation characteristics. The resultant materials, named polyterpenol, were extensively characterised using a number of well−accepted and novel techniques, and their fundamental properties were defined. Polyterpenol films were demonstrated to be hydrocarbon rich, with variable content of oxygen moieties, primarily in the form of hydroxyl and carboxyl functionalities. The level of preservation of original monomer functionality was shown to be strongly dependent on the deposition energy, with higher applied power increasing the molecular fragmentation and substrate temperature. Polyterpenol water contact angle contact angle increased from 62.7° for the 10 W samples to 76.3° for the films deposited at 100 W. Polymers were determined to resist solubilisation by water, due to the extensive intermolecular and intramolecular hydrogen bonds present, and other solvents commonly employed in electronics and biomedical processing. Independent of deposition power, the surface topography of the polymers was shown to be smooth (Rq <0.5 nm), uniform and defect free. Hardness of polyterpenol coatings increased from 0.33 GPa for 10 W to 0.51 GPa for 100 W (at 500 μN load). Coatings deposited at higher input RF powers showed less mechanical deformation during nanoscratch testing, with no considerable damage, cracking or delamination observed. Independent of the substrate, the quality of film adhesion improved with RF power, suggesting these coatings are likely to be more stable and less susceptible to wear. Independent of fabrication conditions, polyterpenol thin films were optically transparent, with refractive index approximating that of glass. Refractive index increased slightly with deposition power, from 1.54 (10 W) to 1.56 (100 W) at 500 nm. The optical band gap values declined with increasing power, from 2.95 eV to 2.64 eV, placing the material within the range for semiconductors. Introduction of iodine impurity reduced the band gap of polyterpenol, from 2.8 eV to 1.64 eV, by extending the density of states more into the visible region of the electromagnetic spectrum. Doping decreased the transparency and increased the refractive index from 1.54 to 1.70 (at 500 nm). At optical frequencies, the real part of permittivity (k) was determined to be between 2.34 and 2.65, indicating a potential low-k material. These permittivity values were confirmed at microwave frequencies, where permittivity increased with input RF energy – from 2.32 to 2.53 (at 10 GHz ) and from 2.65 to 2.83 (at 20 GHz). At low frequencies, the dielectric constant was determined from current−voltage characteristics of Al−polyterpenol−Al devices. At frequencies below 100 kHz, the dielectric constant varied with RF power, from 3.86 to 4.42 at 1 kHz. For all samples, the resistivity was in order of 10⁸−10⁹ _m (at 6 V), confirming the insulating nature of polyterpenol material. In situ iodine doping was demonstrated to increase the conductivity of polyterpenol, from 5.05 × 10⁻⁸ S/cm to 1.20 × 10⁻⁶ S/cm (at 20 V). Exposed to ambient conditions over extended period of time, polyterpenol thin films were demonstrated to be optically, physically and chemically stable. The bulk of ageing occurred within first 150 h after deposition and was attributed to oxidation and volumetric relaxation. Thermal ageing studies indicated thermal stability increased for the films manufactured at higher RF powers, with degradation onset temperature associated with weight loss shifting from 150 ºC to 205 ºC for 10 W and 100 W polyterpenol, respectively. Annealing the films to 405 °C resulted in full dissociation of the polymer, with minimal residue. Given the outcomes of the fundamental characterisation, a number of potential applications for polyterpenol have been identified. Flexibility, tunable permittivity and loss tangent properties of polyterpenol suggest the material can be used as an insulating layer in plastic electronics. Implementation of polyterpenol as a surface modification of the gate insulator in pentacene-based Field Effect Transistor resulted in significant improvements, shifting the threshold voltage from + 20 V to –3 V, enhancing the effective mobility from 0.012 to 0.021 cm²/Vs, and improving the switching property of the device from 10⁷ to 10⁴. Polyterpenol was demonstrated to have a hole transport electron blocking property, with potential applications in many organic devices, such as organic light emitting diodes. Encapsulation of biomedical devices is also proposed, given that under favourable conditions, the original chemical and biological functionality of terpinen−4−ol molecule can be preserved. Films deposited at low RF power were shown to successfully prevent adhesion and retention of several important human pathogens, including P. aeruginosa, S. aureus, and S. epidermidis, whereas films deposited at higher RF power promoted bacterial cell adhesion and biofilm formation. Preliminary investigations into in vitro biocompatibility of polyterpenol demonstrated the coating to be non−toxic for several types of eukaryotic cells, including Balb/c mice macrophage and human monocyte type (HTP−1 non-adherent) cells. Applied to magnesium substrates, polyterpenol encapsulating layer significantly slowed down in vitro biodegradation of the metal, thus increasing the viability and growth of HTP−1 cells. Recently, applied to varied nanostructured titanium surfaces, polyterpenol thin films successfully reduced attachment, growth, and viability of P. aeruginosa and S. aureus.

Prolamin degradation in sourdoughs

This thesis examines protein behaviours that occur during cereal fermentations. The focus is on the prolamin degradation in sourdoughs. The thesis also looks at what happens to the oat globulins during an oat bran acidification process. The cereal prolamins are unique proteins in many respects. The wheat prolamins (glutenins and gliadins) are responsible for the formation of the gluten that provides the viscoelastic properties to wheat doughs whereas the rye prolamins (secalins) are unable to develop gluten-like structures. In addition, many baking technological features, such as flavour, shelf-life and dough properties are affected by the protein degradation that might occur during processing. On the other hand, the prolamins contain protein structures that are harmful to gluten sensitive people. It is thus evident that the degradation of the prolamins in sourdough processes may be approached from various aspects. This thesis describes some of these approaches. Four different cereal fermentations were carried out. Wheat sourdough (WSD) and rye sourdough (RSD) fermentations represented traditional sourdoughs. A germinated-wheat sourdough (GWSD) was a novel sourdough type that was prepared using germinated wheat grains that had high and diverse proteolytic activities. The oat bran fermentation (OBF) represented a fermentation system that lacked functional cereal proteases. The high molecular weight glutenins and rye secalins were degraded during the WSD and RSD fermentations, respectively. It was noteworthy that in WSD only a very limited degradation of the gliadins occurred. The gliadins were, however, hydrolysed very extensively during the GWSD fermentation. No protein degradation was observable in the OBF system. Instead the acidification altered the solubility of the oat globulins and this finally led to their aggregation. This thesis confirms that the endogenous proteases of cereals hydrolyse cereal prolamins in sourdoughs. The thesis also shows that the proteolytic activity of the used cereal raw material determines the extent of proteolysis that occurs in sourdough. This means that bakers may adjust the protein degradation in their sourdoughs by selecting the raw material based on its proteolytic activity. The thesis also demonstrates that by using germinated grains, with high and diverse proteolytic activity in sourdough preparations, the prolamins can be extensively degraded. Whether such highly proteolytic food technology could be used to manufacture new gluten-free cereal-based products for gluten sensitive people remains to be solved.

Food and Indoor Air Isolated Bacillus Non-Protein Toxins: : Structures, Physico-Chemical Properties and Mechanisms of Effects on Eukaryotic Cells

We report here the structures and properties of heat-stable, non-protein, and mammalian cell-toxic compounds produced by spore-forming bacilli isolated from indoor air of buildings and from food. Little information is available on the effects and occurrence of heat-stable non-protein toxins produced by bacilli in moisture-damaged buildings. Bacilli emit spores that move in the air and can serve as the carriers of toxins, in a manner similar to that of the spores of toxic fungi found in contaminated indoor air. Bacillus spores in food cause problems because they tolerate the temperatures applied in food manufacture and the spores later initiate growth when food storage conditions are more favorable. Detection of the toxic compounds in Bacillus is based on using the change in mobility of boar spermatozoa as an indicator of toxic exposure. GC, LC, MS, and nuclear magnetic resonance NMR spectroscopy were used for purification, detection, quantitation, and analysis of the properties and structures of the compounds. Toxicity and the mechanisms of toxicity of the compounds were studied using boar spermatozoa, feline lung cells, human neural cells, and mitochondria isolated from rat liver. The ionophoric properties were studied using the BLM (black-lipid membrane) method. One novel toxin, forming ion channels permeant to K+ > Na+ > Ca2+, was found and named amylosin. It is produced by B. amyloliquefaciens isolated from indoor air of moisture-damaged buildings. Amylosin was purified with an RP-HPLC and a monoisotopic mass of 1197 Da was determined with ESI-IT-MS. Furthermore, acid hydrolysis of amylosin followed by analysis of the amino acids with the GS-MS showed that it was a peptide. The presence of a chromophoric polyene group was found using a NMR spectroscopy. The quantification method developed for amylosin based on RP-HPLC-UV, using the macrolactone polyene, amphotericin B (MW 924), as a reference compound. The B. licheniformis strains isolated from a food poisoning case produced a lipopeptide, lichenysin A, that ruptured mammalian cell membranes and was purified with a LC. Lichenysin A was identified by its protonated molecules and sodium- and potassium- cationized molecules with MALDI-TOF-MS. Its protonated forms were observed at m/z 1007, 1021 and 1035. The amino acids of lichenysin A were analyzed with ESI-TQ-MS/MS and, after acid hydrolysis, the stereoisomeric forms of the amino acids with RP-HPLC. The indoor air isolates of the strain of B. amyloliquefaciens produced not only amylosin but also lipopeptides: the cell membrane-damaging surfactin and the fungicidal fengycin. They were identified with ESI-IT-MS observing their protonated molecules, the sodium- and potassium-cationized molecules and analysing the MS/MS spectra. The protonated molecules of surfactin and fengycin showed m/z values of 1009, 1023, and 1037 and 1450, 1463, 1493, and 1506, respectively. Cereulide (MW 1152) was purified with RP-HPLC from a food poisoning strain of B. cereus. Cereulide was identified with ESI-TQ-MS according to the protonated molecule observed at m/z 1154 and the ammonium-, sodium- and potassium-cationized molecules observed at m/z 1171, 1176, and 1192, respectively. The fragment ions of the MS/MS spectrum obtained from the protonated molecule of cereulide at m/z 1154 were also interpreted. We developed a quantification method for cereulide, using RP-HPLC-UV and valinomycin (MW 1110, which structurally resembles cereulide) as the reference compound. Furthermore, we showed empirically, using the BLM method, that the emetic toxin cereulide is a specific and effective potassium ionophore of whose toxicity target is especially the mitochondria.

How to Succeed in Knowledge Transfer : Case Study of Scandinavian Alliance in Ukraine

The current study of Scandinavian multinational corporate subsidiaries in the rapidly growing Eastern European market, due to their particular organizational structure, attempts to gain some new insights into processes and potential benefits of knowledge and technology transfer. This study explores how to succeed in knowledge transfer and to become more competitive, driven by the need to improve transfer of systematic knowledge for the manufacture of product and service provisions in newly entered market. The scope of current research is exactly limited to multinational corporations, which are defined as enterprises comprising entities in two or more countries, regardless of legal forms and field of activity of those entities, and which operate under a system of decision-making permitting coherent policies and a common strategy through one or more decision-making centers. The entities are linked, by ownership, and able to exercise influence over the activities of the others; and, in particular, to share the knowledge, resources, and responsibilities with others. The research question is "How and to which extent can knowledge-transfer influence a company's technological competence and economic competitiveness?" and try to find out what particular forces and factors affect the development of subsidiary competencies; what factors influence the corporate integration and use of the subsidiary's competencies; and what may increase competitiveness of MNC pursuing leading position in entered market. The empirical part of the research was based on qualitative analyses of twenty interviews conducted among employees in Scandinavian MNC subsidiary units situated in Ukraine, using structured sequence of questions with open-ended answers. The data was investigated by comparison case analyses to literature framework. Findings indicate that a technological competence developed in one subsidiary will lead to an integration of that competence with other corporate units within the MNC. Success increasingly depends upon people's learning. The local economic area is crucial for understanding competition and industrial performance, as there seems to be a clear link between the performance of subsidiaries and the conditions prevailing in their environment. The linkage between competitive advantage and company's success is mutually dependent. Observation suggests that companies can be characterized as clusters of complementary activities such as R&D, administration, marketing, manufacturing and distribution. Study identifies barriers and obstacles in technology and knowledge transfer that is relevant for the subsidiaries' competence development. The accumulated experience can be implemented in new entered market with simple procedures, and at a low cost under specific circumstances, by cloning. The main goal is focused to support company prosperity, making more profits and sustaining an increased market share by improved product quality and/or reduced production cost of the subsidiaries through cloning approach. Keywords: multinational corporation; technology transfer; knowledge transfer; subsidiary competence; barriers and obstacles; competitive advantage; Eastern European market

Veneer Recovery Analysis of Plantation Eucalypt Species Using Spindleless Lathe Technology

The Australian hardwood plantation industry is challenged to identify profitable markets for the sale of its wood fibre. The majority of the hardwood plantations already established in Australia have been managed for the production of pulpwood; however, interest exists to identify more profitable and value-added markets. As a consequence of a predominately pulpwood-focused management regime, this plantation resource contains a range of qualities and performance. Identifying alternative processing strategies and products that suit young plantation-grown hardwoods have proved challenging, with low product recoveries and/or unmarketable products as the outcome of many studies. Simple spindleless lathe technology was used to process 918 billets from six commercially important Australian hardwood species. The study has demonstrated that the production of rotary peeled veneer is an effective method for converting plantation hardwood trees. Recovery rates significantly higher than those reported for more traditional processing techniques (e.g., sawmilling) were achieved. Veneer visually graded to industry standards exhibited favourable recoveries suitable for the manufacture of structural products.

Structural Veneer Based Composite Products from Hardwood Thinning - Part I: Background and Manufacturing

In Australia, plantation forests have increased in area by around 50% in the last 10 years. While this expansion has seen a modest 8% increase for softwoods, hardwood plantations have dramatically increased by over 150%. Hardwood plantations grown for high quality sawn timber are slow to mature, with a crop rotation time potentially reaching 35 years. With this long lead-time, each year the risk from fire, pests and adverse weather events dramatically increases, while not translating into substantially higher financial returns to the grower. To justify continued expansion of Australia's current hardwood plantation estate, it is becoming necessary to develop higher value end-uses for both pulpwood and smaller 'sawlog' resources. The use of the low commercial value stems currently culled during thinning appears to be a necessary option to improve the industry profitability and win new markets. This paper provides background information on Australian forests and plantations and gives an overview of potential uses of Australian hardwood plantation thinning logs, as their mechanical properties. More specifically, this paper reports on the development of structural Veneer Based Composite (VBC) products from hardwood plantation thinning logs, taking advantage of a recent technology developed to optimise the processing of this resource. The process used to manufacture a range of hollow-form veneer laminated structural products is presented and the mechanical characteristics of these products are investigated in the companion paper. The market applications and future opportunities for the proposed products are also discussed, as potential benefits to the timber industry. © RILEM 2014.