Development of a time and space resolved sampling probe diagnostic for engine exhaust hydrocarbons

In order to understand how unburned hydrocarbons emerge from SI engines and, in particular, how non-fuel hydrocarbons are formed and oxidized, a new gas sampling technique has been developed. A sampling unit, based on a combination of techniques used in the Fast Flame Ionization Detector (FFID) and wall-mounted sampling valves, was designed and built to capture a sample of exhaust gas during a specific period of the exhaust process and from a specific location within the exhaust port. The sampling unit consists of a transfer tube with one end in the exhaust port and the other connected to a three-way valve that leads, on one side, to a FFID and, on the other, to a vacuum chamber with a high-speed solenoid valve. Exhaust gas, drawn by the pressure drop into the vacuum chamber, impinges on the face of the solenoid valve and flows radially outward. Once per cycle during a specified crank angle interval, the solenoid valve opens and traps exhaust gas in a storage unit, from which gas chromatography (GC) measurements are made. The port end of the transfer tube can be moved to different locations longitudinally or radially, thus allowing spatial resolution and capturing any concentration differences between port walls and the center of the flow stream. Further, the solenoid valve's opening and closing times can be adjusted to allow sampling over a window as small as 0.6 ms during any portion of the cycle, allowing resolution of a crank angle interval as small as 15°CA. Cycle averaged total HC concentration measured by the FFID and that measured by the sampling unit are in good agreement, while the sampling unit goes one step further than the FFID by providing species concentrations. Comparison with previous measurements using wall-mounted sampling valves suggests that this sampling unit is fully capable of providing species concentration information as a function of air/fuel ratio, load, and engine speed at specific crank angles. © Copyright 1996 Society of Automotive Engineers, Inc.

Designing and testing an advanced pneumatic braking system for heavy vehicles

Heavy goods vehicles exhibit poor braking performance in emergency situations when compared to other vehicles. Part of the problem is caused by sluggish pneumatic brake actuators, which limit the control bandwidth of their antilock braking systems. In addition, heuristic control algorithms are used that do not achieve the maximum braking force throughout the stop. In this article, a novel braking system is introduced for pneumatically braked heavy goods vehicles. The conventional brake actuators are improved by placing high-bandwidth, binary-actuated valves directly on the brake chambers. A made-for-purpose valve is described. It achieves a switching delay of 3-4 ms in tests, which is an order of magnitude faster than solenoids in conventional anti-lock braking systems. The heuristic braking control algorithms are replaced with a wheel slip regulator based on sliding mode control. The combined actuator and slip controller are shown to reduce stopping distances on smooth and rough, high friction (μ = 0.9) surfaces by 10% and 27% respectively in hardware-in-the-loop tests compared with conventional ABS. On smooth and rough, low friction (μ = 0.2) surfaces, stopping distances are reduced by 23% and 25%, respectively. Moreover, the overall air reservoir size required on a heavy goods vehicle is governed by its air usage during an anti-lock braking stop on a low friction, smooth surface. The 37% reduction in air usage observed in hardware-in-the-loop tests on this surface therefore represents the potential reduction in reservoir size that could be achieved by the new system. © 2012 IMechE.

Redescription of Camallanus hypophthalmichthys Dogel and Akhmerov, 1959 (Nematoda : Camallanidae) and its first record from fishes in China

The nematode Camallanus hypophthalmichthys Dogel and Akhmerov, 1959 is redescribed from specimens collected from the intestine of the bighead carp Aristichthys nobilis, from Liangzihu Lake (Yangtze River basin), Hubei Province, central China. The light and scanning electron microscopical examination made it possible to study in detail the morphology of this so far little-known species and to confirm its validity. The main specific features of C. hypophthalmichthys distinguishing it from the most similar Camallanus spp. is the presence of 3 small caudal processes on the male tail tip, 13-16 longitudinal ridges on the inner surface of the valve of the buccal capsule, and the arrangement of preanal and postanal genital papillae in the male. This finding represents a new host record, the first record of this parasite in the Yangtze River basin, and the first documented record of C. hypophthalmichthys from China. Camallanus hypophthalmichthys is considered a specific intestinal parasite of fishes of the cyprinid Hypophthalmichthyinae.

Interlayer segregation in magnetic multilayers and its influence on exchange coupling

Experimental results show that the exchange coupling field (H-ex) of NiFe/FeMn for Ta/NiFe/FeMn/Ta multilayers is higher than that for spin-valve multilayers Ta/NiFe/Cu/NiFe/FeMn/Ta. X-ray photoelectron spectroscopy shows that Cu atoms segregate to the NiFe/FeMn interface for Ta/NiFe/Cu/NiFe/FeMn/Ta multilayers. While studying Ta/X(X=Bi,Pb,Ag,In)/NiFe/FeMn multilayers, we also find that X atoms segregate to the NiFe/FeMn interface, which results in a decrease of the H-ex. However, a small amount of Bi, Pb, etc. deposited between Cu and pinned NiFe layer for Ta/NiFe/Cu/NiFe/FeMn/Ta multilayers can increase H-ex. (C) 2003 American Institute of Physics.

Interlayer segregation of Cu atoms in metal multilayers

The experimental results show that the exchange coupling field H.. of NiFe/FeMn for TalNiFe/FeMn/Ta multilayers is higher than that for the spin valve multilayers Ta/NiFe/Cu/NiFe/FeMn/Ta. The composition and chemical states at the surface of Ta(12nm)/NiFe(7nm), Th(12nm)/NiFe(7nm)/Cu(4nm) and Ta(12nm)/NiFe(7nm)/Cu(3 nm)/NiFe(5 mn) were studied by using x-ray photoelectron spectroscopy. The results show that no element from the underlayers Boats out or segregates to the surface for Th(12 nm)/NiFe(7nm), Ta(12 nm)/NiFe(7nm)/Cu(4 mn). However, Cu atoms segregate to the surface of Ta(12 nm)/NiFe(7nm)/Cu(3nm)/NiFe(5nm) multilayers, i.e. to the NiFe/FeMn interface for Ta/NiFe/Cu/NiFe/FeMn/Ta multilayers. We believe that the presence of Cu atoms at the interface of NiFe/FeMn is one of the important factors which will cause the exchange coupling field H.. of Ta/NiFe/FeMn/Ta multilayers to be higher than that of Ta/NiFe/Cu/NiFe/FeMn/Ta multilayers.

MBE Growth of High Electron Mobility InP Epilayers

The molecular beam epitaxial growth of high quality epilayers on （100） InP substrate using a valve phosphorous cracker cell over a wide range of P/In BEP ratio （2.0-7.0） and growth rate （0.437 and 0. 791μm/h）. Experimental results show that electrical properties exhibit a pronounced dependence on growth parameters,which are growth rate, P/In BEP ratio, cracker zone temperature, and growth temperature. The parameters have been optimized carefully via the results of Hall measurements. For a typical sample, 77K electron mobility of 4.57 × 10^4 cm^2/（V · s） and electron concentration of 1.55×10^15 cm^-3 have been achieved with an epilayer thickness of 2.35μm at a growth temperature of 370℃ by using a cracking zone temperature of 850℃.

ECR离子源高真空微调针阀控制系统

本论文首先介绍ECR（电子回旋共振）离子源的基本原理及其发展，在此基础上讲述了近物所的14.5GHzECR离子源的结构和特点。本论文主要内容是介绍所研制的适用于30KV高压端的ECR离子源高真空微调针阀控制系统。此系统被控对象是位于ECR源上的高真空微调针阀，它与地面之间有20～30KV的电位差。论文中首先阐述此控制系统研究的背景，并对ECR离子源电气参数控制的特点进行了说明。根据被控对象的情况以及对系统提出的指标，详细讲述了此控制系统的软、硬件实现。硬件包括步进电机、步进电机驱动器、轴编码器等。软件包括译码编程。然后从总体介绍此控制系统的功能结构，再分步讲述发射器、接受器、译码等各功能模块的实现过程。此控制系统的最大特点是使用光路实现高压绝缘，这为解决位于ECR离子源高压端器件的控制问题提出新思路。本系统的光路采用红外线发射接收系统，以空气为传输介质，依据光信号的有无接收控制信息，此方式效果好、易于实现。在系统中，使用光路传输装置定位，聚集透镜聚集，增加信号强度，提高抗干拢能力。而且此光路传输系统价格便宜，易于实现，可靠性好。在整个控制系统方案调研期间，对各种控制方式进行了比较和实验，在此基础上，确定了一个比较经济实用和具有高可靠性的方案。经过设计电路原理图、绘制印制线路板、加工印制线路板、购买元器件、组装电路后，首先成功地进行了离线调试，最后，将整个系统模拟实际环境进行调试实验。整个系统实现了稳定可靠的工作，达到了预期的设计指标，精度好于要求的千分之一。由于时间紧张和条件的限制，该系统还未在现场设备上进行实验。因此，在今后的工作中，此控制系统还需要在条件具备时，在现场设备上进行实验和考验。此外，为满足国家大科学工程兰洲重离子冷却储存环的要求，我参与了在14.5GHz ECR离子源上进行afterglow工作模式的实验，首次产生了高电荷态脉冲束流Ar~(11+)和Ar~(12+)。论文最后一部分给出了初步实验结果，并对结果进行了分析和解释。

On-line introduction of high-pressure gas-liquid sample for capillary gas chromatographic analysis

An on-line sample introduction technique in capillary gas chromatograph (CGC) for the analysis of high-pressure gas-liquid mixtures has been designed and evaluated. A sample loop of 0.05 muL and a washing solvent loop of 0.5 muL are mounted on a 10-port switching valve, which serves as the injection valve. A capillary resistor was connected to the vent of sample loop in order to maintain the pressure of the sample. Both the sample and the washing solvent are transferred into the split-injection port through a narrow bore fused silica capillary inserted into the injection liner through a septum. The volume of the liner is used both as the pressure-release damper and evaporation chamber of the sample. On-line analysis of both reactants and resultants in ethylene olimer reaction mixture at 5 MPa was carried out, which demonstrated the applicability of the technique. (C) 2004 Elsevier B.V. All rights reserved.

Study of an electroosmotic pump for liquid delivery and its application in capillary column liquid chromatography

A packed-bed electroosmotic pump (EOP) was constructed and evaluated. The EOP consisted of three capillary columns packed in parallel, a gas-releasing device, Pt electrodes and a high-voltage power supply. The EOP could generate output pressure above 5.0 MPa and constant flow rate in the range of nl/min to a few mul/min for pure water, pure methanol, 2 mM potassium dihydrogenphosphate buffer, the buffer-methanol mixture and the pure water-methanol mixture at applied potentials less than 20 W The composition of solvent before/after pumping was quantitatively determined by using a gas chromatograph equipped with both flame ionization detector and thermal conductivity detector. It was found that there were no apparent changes in composition and relative concentrations after pumping process for a methanol-ethanol-acetonitrile mixture and a methanol-water mixture. Theoretical aspect of the EOP was discussed in detail. An capillary HPLC system consisting of the EOP, an injection valve, a 15 cm x 320 mum i.d., 5 mum Spherigel C(18) stainless steel analytical column, and an on-column UV detector was connected to evaluate the performance of the EOP. A comparative study was also carried out with a mechanical capillary HPLC pump on the same system. The results demonstrated that the reproducibility of flow rate and the pulsation-free flow property of the EOP are superior to that of mechanical pump in capillary HPLC application. (C) 2004 Elsevier B.V. All rights reserved.

Separation and identification of compounds in Rhizoma chuanxiong by comprehensive two-dimensional liquid chromatography coupled to mass spectrometry

A comprehensive two-dimensional liquid chromatographic separation system based on the combination of a CN column and an ODS column is developed for the separation of components in a traditional Chinese medicine (TCM) Rhizoma chuanxiong. Two columns are coupled by a two-position, eight-port valve equipped with two storage loops and controlled by a computer. The effluent is detected by both the diode array detector and atmospheric pressure chemical ionization (APCI) mass spectrometer. More than 52 components in the methanol extract of R. chuanxiong were resolved and 11 of them were preliminary identified according to their UV and mass spectra. (C) 2004 Elsevier B.V. All rights reserved.

趋磁细菌AMB-1培养条件优化及磁小体变化过程研究

趋磁细菌(Magnetotactic bacteria)的研究是国际微生物学研究热点之一。趋磁细菌体内含有纳米单磁畴的氧化铁/硫化铁(Fe3O4或Fe3S4)晶体，称为磁小体。由于趋磁细菌营养条件要求苛刻，在环境中需要微好氧条件，且营养类型属于化能自养，使得培养趋磁细菌时常遇到问题。 本研究首先通过正交试验优化趋磁细菌AMB-1菌株培养条件，在培养条件铁源为奎尼酸铁0.02 mmol/L，装瓶量75% ，pH值6.7，温度25 ℃时，AMB-1 OD600达到0.440(1.166×109 cells/ml)。同时运用磁收集传代法，使带有磁小体的AMB-1细胞比例占95％以上(Cmag值稳定在1.9-2.0)。 在AMB-1具有较好的生物量，同时又具有较好的含磁小体细胞比例后，研究磁小体的变化过程。通过透射电镜观察磁小体变化过程，发现培养24 h细菌体内已有较小晶体形成(平均27 nm，n=188)且沿长轴分布；48 h晶体长大(平均43 nm，n=203)且形成分段链沿长轴排列；72 h晶体进一步成熟(平均50 nm，n=191)仍以分段链沿长轴排列；随后细菌逐渐衰亡磁小体变小，168 h可见部分自溶细菌中仍有磁小体链(平均37 nm，n=186)；192 h细菌自溶磁小体链(平均33 nm，n=184)分散到环境中。 通过透射电镜在细胞水平上研究趋磁细菌细胞分裂时发现，磁小体在细菌分裂时采用两种分离方式：一种为磁小体分配到两个子细胞；另一种为磁小体只分配到一个子细胞。无磁小体的子细胞，在随后的生长过程又分为两种情况：一种为细胞逐渐产生磁小体，另一种为不再产生磁小体。这种现象的发现，解释了随着传代次数的增多，细菌磁性有所下降的原因(Cmag值降低)。 在对趋磁细菌磁小体合成机制的研究中，常使用基因敲除的办法获得缺陷型，并与野生型对比进行研究。但是，利用基因敲除获得缺陷型不仅操作繁琐并且所得缺陷型不稳定。本研究利用特殊的磁富集传代法，先将带有磁小体的菌体收集并连续传代，筛选获得了高磁菌株；利用这种方法，收集不含磁小体的菌体并连续传代，筛选获得了无磁菌株。 趋磁细菌磁小体在医疗、环保等领域具有广阔应用价值，但是目前由于趋磁细菌难以大规模培养，并且磁小体纯化存在成本高等原因，将磁小体真正实际应用尚有一段距离。通过研究磁小体在趋磁细菌中的变化过程发现，AMB-1菌株在培养192 h后自溶，并且磁小体随着细胞的破碎释放到环境中去。

基于无线通信的阀门泄漏检测系统

阀门泄漏的在线监测一直是困扰流程工业的难题,采用传统有线监控方式需要巨大的布线安装成本。本文通过结合无线通信技术和超声检测技术,研究并开发了一种基于无线通信的阀门泄漏检测系统,可极大地降低测控系统的投资和使用成本,通过实时检测阀门的工作状态,及时发现并定位泄漏位置,实现工业生产的节能降耗。