Analyzing the cost-efficiency and performance of a payroll department by benchmarking

Tämän diplomityön tavoitteena oli analysoida Stora Enson palkkakeskuksen ja sen henkilöstöhallinnon järjestelmän, SAP HR:n, kustannustehokkuutta ja suorituskykyä. Tutkimuksessa käytettiin apuna benchmarkingia. Viisi suurta suomalaisyritystä osallistui benchmarkingiin. Benchmarkingin pääkohteena oli yritysten välinen kustannusvertailu. Kyselyssä perehdyttiin myös yritysten järjestelmien suorituskykyyn. Tuloksien perusteella Stora Enson palkkakeskus tarjoaa kustannustehokkaan ja kilpailukykyisen ratkaisun, joka menestyy hyvin vertailussa muihin suomalaisiin yrityksiin.

Balancing effluent quality, economic cost and greenhouse gas emissions during the evaluation of (plant-wide) control/operational strategies in WWTPs

The objective of this paper was to show the potential additional insight that result from adding greenhouse gas (GHG) emissions to plant performance evaluation criteria, such as effluent quality (EQI) and operational cost (OCI) indices, when evaluating (plant-wide) control/operational strategies in wastewater treatment plants (WWTPs). The proposed GHG evaluation is based on a set of comprehensive dynamic models that estimate the most significant potential on-site and off-site sources of CO2, CH4 and N2O. The study calculates and discusses the changes in EQI, OCI and the emission of GHGs as a consequence of varying the following four process variables: (i) the set point of aeration control in the activated sludge section; (ii) the removal efficiency of total suspended solids (TSS) in the primary clarifier; (iii) the temperature in the anaerobic digester; and (iv) the control of the flow of anaerobic digester supernatants coming from sludge treatment. Based upon the assumptions built into the model structures, simulation results highlight the potential undesirable effects of increased GHG production when carrying out local energy optimization of the aeration system in the activated sludge section and energy recovery from the AD. Although off-site CO2 emissions may decrease, the effect is counterbalanced by increased N2O emissions, especially since N2O has a 300-fold stronger greenhouse effect than CO2. The reported results emphasize the importance and usefulness of using multiple evaluation criteria to compare and evaluate (plant-wide) control strategies in a WWTP for more informed operational decision making

A low-cost ultrasonic spray dryer to produce spherical microparticles from polymeric matrices

The spray-drying technique has been widely used for drying heat-sensitive foods, pharmaceuticals, and other substances, because it leads to rapid solvent evaporation from droplets. This method involves the transformation of a feed from a fluid state into a dried particulate, by spraying the feed into a hot medium. Despite being most often considered a dehydration process, spray drying can also be used as an encapsulation method. Therefore, this work proposes the use of a simple and low-cost ultrasonic spray dryer system to produce spherical microparticles. This equipment was successfully applied to the preparation of dextrin microspheres on a laboratory scale and for academic purposes.

Estimation of lung cancer diagnosis and treatment costs based on a patient-level analysis in Catalonia (Spain)

Background: Assessing of the costs of treating disease is necessary to demonstrate cost-effectiveness and to estimate the budget impact of new interventions and therapeutic innovations. However, there are few comprehensive studies on resource use and costs associated with lung cancer patients in clinical practice in Spain or internationally. The aim of this paper was to assess the hospital cost associated with lung cancer diagnosis and treatment by histology, type of cost and stage at diagnosis in the Spanish National Health Service. Methods: A retrospective, descriptive analysis on resource use and a direct medical cost analysis were performed. Resource utilisation data were collected by means of patient files from nine teaching hospitals. From a hospital budget impact perspective, the aggregate and mean costs per patient were calculated over the first three years following diagnosis or up to death. Both aggregate and mean costs per patient were analysed by histology, stage at diagnosis and cost type. Results: A total of 232 cases of lung cancer were analysed, of which 74.1% corresponded to non-small cell lung cancer (NSCLC) and 11.2% to small cell lung cancer (SCLC); 14.7% had no cytohistologic confirmation. The mean cost per patient in NSCLC ranged from 13,218 Euros in Stage III to 16,120 Euros in Stage II. The main cost components were chemotherapy (29.5%) and surgery (22.8%). Advanced disease stages were associated with a decrease in the relative weight of surgical and inpatient care costs but an increase in chemotherapy costs. In SCLC patients, the mean cost per patient was 15,418 Euros for limited disease and 12,482 Euros for extensive disease. The main cost components were chemotherapy (36.1%) and other inpatient costs (28.7%). In both groups, the Kruskall-Wallis test did not show statistically significant differences in mean cost per patient between stages. Conclusions: This study provides the costs of lung cancer treatment based on patient file reviews, with chemotherapy and surgery accounting for the major components of costs. This cost analysis is a baseline study that will provide a useful source of information for future studies on cost-effectiveness and on the budget impact of different therapeutic innovations in Spain.

LOW COST ANALYZER FOR THE DETERMINATION OF PHOSPHORUS BASED ON OPEN-SOURCE HARDWARE AND PULSED FLOWS

The need for automated analyzers for industrial and environmental samples has triggered the research for new and cost-effective strategies of automation and control of analytical systems. The widespread availability of open-source hardware together with novel analytical methods based on pulsed flows have opened the possibility of implementing standalone automated analytical systems at low cost. Among the areas that can benefit from this approach are the analysis of industrial products and effluents and environmental analysis. In this work, a multi-pumping flow system is proposed for the determination of phosphorus in effluents and polluted water samples. The system employs photometric detection based on the formation of molybdovanadophosphoric acid, and the fluidic circuit is built using three solenoid micropumps. The detection is implemented with a low cost LED-photodiode photometric detection system and the whole system is controlled by an open-source Arduino Uno microcontroller board. The optimization of the timing to ensure the color development and the pumping cycle is discussed for the proposed implementation. Experimental results to evaluate the system behavior are presented verifying a linear relationship between the relative absorbance and the phosphorus concentrations for levels as high as 50 mg L-1.

Estimation of existing cable systems in generator-busbar unit and choice the optimal solution for its modernization

The aim of this master’s thesis is to develop an algorithm to calculate the cable network for heat and power station CHGRES. This algorithm includes important aspect which has an influence on the cable network reliability. Moreover, according to developed algorithm, the optimal solution for modernization cable system from economical and technical point of view was obtained. The conditions of existing cable lines show that replacement is necessary. Otherwise, the fault situation would happen. In this case company would loss not only money but also its prestige. As a solution, XLPE single core cables are more profitable than other types of cable considered in this work. Moreover, it is presented the dependence of value of short circuit current on number of 10/110 kV transformers connected in parallel between main grid and considered 10 kV busbar and how it affects on final decision. Furthermore, the losses of company in power (capacity) market due to fault situation are presented. These losses are commensurable with investment to replace existing cable system.

Supply chain cost saving potential analysis

Target of this study was to examine the current supply chain with focus on external part and identify the cost potential areas which lie there. The goal was to evaluate the cost save potential and give estimate what would be required in order to realise it. Base data related to study was searched and examined with using company’s enterprise resource planning system. In case feasible two types of scenarios were built in order to describe the scale of save potential. First scenario was theoretical and achieving it would require further investments and second scenario was realistic approach where more limitations were taken into account. The results clearly show that there is high save potential in supply chain costs linked to balance between internal and external operations. Realising of it would require at least minor investments as current internal capacity is not on a level to fully absorb the additional volumes which are needed in order to realise the potential. This study can be used as a basis when starting new projects related to investment needs.

Phase voltage control and filtering in a converter-fed single-phase customer-end system of the LVDC distribution network

In recent years, the network vulnerability to natural hazards has been noticed. Moreover, operating on the limits of the network transmission capabilities have resulted in major outages during the past decade. One of the reasons for operating on these limits is that the network has become outdated. Therefore, new technical solutions are studied that could provide more reliable and more energy efficient power distributionand also a better profitability for the network owner. It is the development and price of power electronics that have made the DC distribution an attractive alternative again. In this doctoral thesis, one type of a low-voltage DC distribution system is investigated. Morespecifically, it is studied which current technological solutions, used at the customer-end, could provide better power quality for the customer when compared with the current system. To study the effect of a DC network on the customer-end power quality, a bipolar DC network model is derived. The model can also be used to identify the supply parameters when the V/kW ratio is approximately known. Although the model provides knowledge of the average behavior, it is shown that the instantaneous DC voltage ripple should be limited. The guidelines to choose an appropriate capacitance value for the capacitor located at the input DC terminals of the customer-end are given. Also the structure of the customer-end is considered. A comparison between the most common solutions is made based on their cost, energy efficiency, and reliability. In the comparison, special attention is paid to the passive filtering solutions since the filter is considered a crucial element when the lifetime expenses are determined. It is found out that the filter topology most commonly used today, namely the LC filter, does not provide economical advantage over the hybrid filter structure. Finally, some of the typical control system solutions are introduced and their shortcomings are presented. As a solution to the customer-end voltage regulation problem, an observer-based control scheme is proposed. It is shown how different control system structures affect the performance. The performance meeting the requirements is achieved by using only one output measurement, when operating in a rigid network. Similar performance can be achieved in a weak grid by DC voltage measurement. An additional improvement can be achieved when an adaptive gain scheduling-based control is introduced. As a conclusion, the final power quality is determined by a sum of various factors, and the thesis provides the guidelines for designing the system that improves the power quality experienced by the customer.

Insulation System in an Integrated Motor Compressor

A high-speed and high-voltage solid-rotor induction machine provides beneficial features for natural gas compressor technology. The mechanical robustness of the machine enables its use in an integrated motor-compressor. The technology uses a centrifugal compressor, which is mounted on the same shaft with the high-speed electrical machine driving it. No gearbox is needed as the speed is determined by the frequency converter. The cooling is provided by the process gas, which flows through the motor and is capable of transferring the heat away from the motor. The technology has been used in the compressors in the natural gas supply chain in the central Europe. New areas of application include natural gas compressors working at the wellheads of the subsea gas reservoir. A key challenge for the design of such a motor is the resistance of the stator insulation to the raw natural gas from the well. The gas contains water and heavy hydrocarbon compounds and it is far harsher than the sales gas in the natural gas supply network. The objective of this doctoral thesis is to discuss the resistance of the insulation to the raw natural gas and the phenomena degrading the insulation. The presence of partial discharges is analyzed in this doctoral dissertation. The breakdown voltage of the gas is measured as a function of pressure and gap distance. The partial discharge activity is measured on small samples representing the windings of the machine. The electrical field behavior is also modeled by finite element methods. Based on the measurements it has been concluded that the discharges are expected to disappear at gas pressures above 4 – 5 bar. The disappearance of discharges is caused by the breakdown strength of the gas, which increases as the pressure increases. Based on the finite element analysis, the physical length of a discharge seen in the PD measurements at atmospheric pressure was approximated to be 40 – 120 m. The chemical aging of the insulation when exposed to raw natural gas is discussed based on a vast set of experimental tests with the gas mixture representing the real gas mixture at the wellhead. The mixture was created by mixing dry hydrocarbon gas, heavy hydrocarbon compounds, monoethylene glycol, and water. The mixture was chosen to be more aggressive by increasing the amount of liquid substances. Furthermore, the temperature and pressure were increased, which resulted in accelerated test conditions. The time required to detect severe degradation was thus decreased. The test program included a comparison of materials, an analysis of the e ects of di erent compounds in the gas mixture, namely water and heavy hydrocarbons, on the aging, an analysis of the e ects of temperature and exposure duration, and also an analysis on the e ect of sudden pressure changes on the degradation of the insulating materials. It was found in the tests that an insulation consisting of mica, glass, and epoxy resin can tolerate the raw natural gas, but it experiences some degradation. The key material in the composite insulation is the resin, which largely defines the performance of the insulation system. The degradation of the insulation is mostly determined by the amount of gas mixture di used into it. The di usion was seen to follow Fick’s second law, but the coe cients were not accurately defined. The di usion was not sensitive to temperature, but it was dependent upon the thermodynamic state of the gas mixture, in other words, the amounts of liquid components in the gas. The weight increase observed was mostly related to heavy hydrocarbon compounds, which act as plasticizers in the epoxy resin. The di usion of these compounds is determined by the crosslink density of the resin. Water causes slight changes in the chemical structure, but these changes do not significantly contribute to the aging phenomena. Sudden changes in pressure can lead to severe damages in the insulation, because the motion of the di used gas is able to create internal cracks in the insulation. Therefore, the di usion only reduces the mechanical strength of the insulation, but the ultimate breakdown can potentially be caused by a sudden drop in the pressure of the process gas.

Porvoon jalostamon haihtuvien orgaanisten yhdisteiden päästömääritysmenetelmät

Työssä käytiin läpi Porvoon jalostamon haihtuvien orgaanisten yhdisteiden päästömääritysmenetelmiä ja arvioitiin nykyisin käytössä olevien sekä uusien menetelmien soveltuvuutta Porvoon jalostamon päästömääritykseen. Nykyisten menetelmien arviointia tehtiin käymällä läpi eri alueiden 2000-luvun päästömäärät sekä vertaamalla päästömääriä muiden jalostamojen vastaaviin päästömääriin. Haihtuvista orgaanisista yhdisteistä puhuttaessa jätetään yleisesti metaani määritelmän ulkopuolelle ja käytetään termiä NMVOC-yhdisteet. Työssä laskettiin arvio Porvoon jalostamon metaanin päästömäärälle ja arvioitiin sen vaikutusta NMVOC-kokonaispäästömäärään. Metaanin kokonaispäästömäärien havaittiin olevan noin kymmenen kertaa haihtuvien orgaanisten yhdisteiden päästömääriä pienempiä, ja näin ollen niiden lisäämisellä NMVOC-päästöihin ei ole juuri vaikutusta. Myös menetelmien investointi- ja käyttökustannuksia, sekä pidemmän aikavälin kustannuksia arvioitiin. Kustannuksiltaan tällä hetkellä Porvoon jalostamolla käytössä olevat menetelmät ovat kustannustehokkaita. Uusista menetelmistä DIAL, SOF ja OGI ovat kustannuksiltaan huomattavasti kalliimpia, myös pitkän aikavälin vertailulla. Nykyisten menetelmien vuosittaiset kustannukset aiheutuvat mittausten vaatimista henkilötyötunneista. Uusista menetelmistä SOF ja DIAL vaativat ulkopuolisten mittaajien käyttämistä. Massavirran määrityksen suhteen vielä kehitysvaiheessa olevalla OGI-kameralla mitatessa voidaan käyttää mittaajina omaa henkilökuntaa. Toisin kuin DIAL- ja SOF-menetelmien laitteistot, OGI-kamera ostetaan omaksi ja näin ollen sitä voidaan käyttää tarpeen vaatiessa vuoden ympäri esimerkiksi suurien vuotajien paikallistamiseen ja LDAR-kiristysohjelman tukena. Tarkastelun perusteella olisi suositeltavaa tarkastaa nykyisin käytettävistä laskentamenetelmistä erityisesti prosessi- ja säiliöalueen sekä jätevesijärjestelmä päästömäärät käyttäen tarkempia DIAL-, SOF- tai myöhemmin OGI-menetelmiä ja muokata laskentamenetelmiä vastamaan näillä määritettyjä päästömääriä.

Costs and Benefits of a Shared Digital Long-Term Preservation System

Paper presented at the 40th Annual Conference of LIBER (Ligue des Bibliothèques Européennes de Recherche - Association of European Research Libraries) on July 1st, 2011; with the slides used at the presentation.

Costs and Benefits of a Shared Digital Long-Term Preservation System

This paper describes the cost-benefit analysis of digital long-term preservation (LTP) that was carried out in the context of the Finnish National Digital Library Project (NDL) in 2010. The analysis was based on the assumption that as many as 200 archives, libraries, and museums will share an LTP system. The term ‘system’ shall be understood as encompassing not only information technology, but also human resources, organizational structures, policies and funding mechanisms. The cost analysis shows that an LTP system will incur, over the first 12 years, cumulative costs of €42 million, i.e. an average of €3.5 million per annum. Human resources and investments in information technology are the major cost factors. After the initial stages, the analysis predicts annual costs of circa €4 million. The analysis compared scenarios with and without a shared LTP system. The results indicate that a shared system will have remarkable benefits. At the development and implementation stages, a shared system shows an advantage of €30 million against the alternative scenario consisting of five independent LTP solutions. During the later stages, the advantage is estimated at €10 million per annum. The cumulative cost benefit over the first 12 years would amount to circa €100 million.

ALLOMETRIC MODELS FOR ESTIMATING ABOVEGROUND BIOMASS AND BIOMASS ALLOCATION OF CAPIXINGUI TREES (Croton floribundus Spreng.) IN AN AGRISILVICULTURAL SYSTEM

ABSTRACT The objective of this study was to select allometric models to estimate total and pooled aboveground biomass of 4.5-year-old capixingui trees established in an agrisilvicultural system. Aboveground biomass distribution of capixingui was also evaluated. Single- (diameter at breast height [DBH] or crown diameter or stem diameter as the independent variable) and double-entry (DBH or crown diameter or stem diameter and total height as independent variables) models were studied. The estimated total biomass was 17.3 t.ha-1, corresponding to 86.6 kg per tree. All models showed a good fit to the data (R2ad > 0.85) for bole, branches, and total biomass. DBH-based models presented the best residual distribution. Model lnW = b0 + b1* lnDBH can be recommended for aboveground biomass estimation. Lower coefficients were obtained for leaves (R2ad > 82%). Biomass distribution followed the order: bole>branches>leaves. Bole biomass percentage decreased with increasing DBH of the trees, whereas branch biomass increased.

Detection of soybean planted areas through orbital images based on culture spectral dynamics

The soybean is important to the economy of Brazil, so the estimation of the planted area and the production with higher antecedence and reliability becomes essential. Techniques related to Remote Sensing may help to obtain this information at lower cost and less subjectivity in relation to traditional surveys. The aim of this study is to estimate the planted area with soybean culture in the crop of 2008/2009 in cities in the west of the state of Paraná, in Brazil, based on the spectral dynamics of the culture and through the use of the specific system of analysis for images of Landsat 5/TM satellite. The obtained results were satisfactory, because the classification supervised by Maximum Verisimilitude - MaxVer along with the techniques of the specific system of analysis for satellite images has allowed an estimate of soybean planted area (soybean mask), obtaining values ​​of the metrics of Global Accuracy with an average of 79.05% and Kappa Index over 63.50% in all cities. The monitoring of a reference area was of great importance for determining the vegetative phase in which the culture is more different from the other targets, facilitating the choice of training samples (ROIs) and avoiding misclassifications.

Low cost driver device for microclimate maintenance in the pre-milking of dairy cattle

Due to the importance of the environment on animal production and thus environmental control, the study aims to build a system for monitoring and control the meteorological variables, temperature and relative humidity, low cost, which can be associated with an evaporative cooling system (ECS). The system development included all the stages of assembly, test and laboratory calibration, and later the validation of the equipment carried in the field. The validation step showed results which allowed concluding that the system can be safely used in the monitoring of these variables. The controller was efficient in management of the microclimate in the waiting corral and allowed the maintenance of the air temperature within the comfort range for dairy cattle in pre-milking with averaged 25.09 ºC during the afternoon. The equipment showed the lower cost (R$ 325.76) when compared to other middle market (R$ 450.00).