Utilization of non-wood pulp in different fibers products

The correct utilization of non-wood raw material allows reducing tree cutting and reduces emissions of carbon dioxide from burning of non-wood plants on farmers fields. Also it allows increasing economical situation in regions that non-wood plants are grown and where they are converted into pulp and paper. Also it gives positive effect on population pressure of work by addition of working place. In the literature survey included an overview of the historical meaning of non-wood pulp on developing paper production and structure of non-wood pulps. Moreover, anatomical and chemical composition of straw, reed and bamboo were studied more detailed. Also, an overview of the utilization of non-wood pulp in papermaking was made. Especially tissue, tree-free and release papers were reviewed. In the experimental part the goal was to investigate suitability of non-wood pulp like wheat straw pulp and bamboo pulp for different fiber products. Finally release and tree-free paper products were selected for experimental studies. It was discovered that wheat straw, especially screened wheat straw, showed good results for release paper. Also utilization of wheat straw and bamboo pulp in tree-free paper showed good results and suitability of these non-wood pulps for tree-free paper production. Also it was noticed that addition of wheat straw pulp gave positive effect on initial wet strength for release and tree-free paper.

Utilization of a Time Domain Simulator in the Technical and Economic Analysis of a Wind Turbine Electric Drive Train

The amount of installed wind power has been growing exponentially during the past ten years. As wind turbines have become a significant source of electrical energy, the interactions between the turbines and the electric power network need to be studied more thoroughly than before. Especially, the behavior of the turbines in fault situations is of prime importance; simply disconnecting all wind turbines from the network during a voltage drop is no longer acceptable, since this would contribute to a total network collapse. These requirements have been a contributor to the increased role of simulations in the study and design of the electric drive train of a wind turbine. When planning a wind power investment, the selection of the site and the turbine are crucial for the economic feasibility of the installation. Economic feasibility, on the other hand, is the factor that determines whether or not investment in wind power will continue, contributing to green electricity production and reduction of emissions. In the selection of the installation site and the turbine (siting and site matching), the properties of the electric drive train of the planned turbine have so far been generally not been taken into account. Additionally, although the loss minimization of some of the individual components of the drive train has been studied, the drive train as a whole has received less attention. Furthermore, as a wind turbine will typically operate at a power level lower than the nominal most of the time, efficiency analysis in the nominal operating point is not sufficient. This doctoral dissertation attempts to combine the two aforementioned areas of interest by studying the applicability of time domain simulations in the analysis of the economicfeasibility of a wind turbine. The utilization of a general-purpose time domain simulator, otherwise applied to the study of network interactions and control systems, in the economic analysis of the wind energy conversion system is studied. The main benefits of the simulation-based method over traditional methods based on analytic calculation of losses include the ability to reuse and recombine existing models, the ability to analyze interactions between the components and subsystems in the electric drive train (something which is impossible when considering different subsystems as independent blocks, as is commonly done in theanalytical calculation of efficiencies), the ability to analyze in a rather straightforward manner the effect of selections other than physical components, for example control algorithms, and the ability to verify assumptions of the effects of a particular design change on the efficiency of the whole system. Based on the work, it can be concluded that differences between two configurations can be seen in the economic performance with only minor modifications to the simulation models used in the network interaction and control method study. This eliminates the need ofdeveloping analytic expressions for losses and enables the study of the system as a whole instead of modeling it as series connection of independent blocks with no lossinterdependencies. Three example cases (site matching, component selection, control principle selection) are provided to illustrate the usage of the approach and analyze its performance.

Dental Health in Primary Teeth after Prevention of Mother-Child Transmission of Mutans Streptococci. A Historical Cohort Study on Restorative Visits and Maternal Prevention Costs

Mutansstreptokokkitartunnan ehkäisemisen pitkäaikaisvaikutukset maitohampaiden terveyteen. Kohorttitutkimus korjaavan hoidon määrästä ja kariesehkäisyn kustannuksista. Tutkimuksen tarkoituksena oli selvittää varhaisen mutansstreptokokki (MS)-kolonisaation ehkäisyn pitkäaikaisvaikutuksia korkean kariesriskin omaavien lasten maitohampaistossa sekä tarkastella MS-tartunnan estämisen kustannuksia. Tiedot lasten hampaiden terveydestä ja hammashoitotoimenpiteistä syntymästä 10-vuotiaaksi sekä äiteihin kohdistuneen kariesehkäisyn kustannuksista kerättiin Ylivieskan terveyskeskuksen asiakirjoista. Tutkimuksessa oli mukana yhteensä 507 lasta, heistä 148 oli osallistunut aikaisempaan Ylivieskan äiti-lapsitutkimukseen, jossa verrattiin äitien käyttämän ksylitolipurukumin ja äidille tehtyjen fluori- tai klooriheksidiinilakkausten vaikutusta pikkulasten hampaiden terveyteen. Maitohammaskariesta esiintyi 10-vuotiaaksi asti merkitsevästi vähemmän lapsilla, jotka eivät olleet saaneet MS-tartuntaa alle 2-vuotiaana, heidän maitohampaansa säilyivät 3,4 vuotta kauemmin täysin ehjinä (p<0.001) ja he tarvitsivat vähemmän maitohampaiden korjaavaa hoitoa (p=0.005) kuin lapset, joiden hampaisto oli kolonisoitunut MS-bakteerilla jo 2-vuotiaana. Koska ksylitoliryhmän lasten MS-kolonisaatio oli vähäisintä, heidän maitohampaissaan oli vähemmän kariesta ja korjaavan hoidon tarvetta kuin kahden muun korkeariskisen ryhmän lapsilla. Äitien käyttämän ksylitolipurukumin kustannukset olivat yhteensä 116 euroa ja lapsen maitohampaiden säilyminen täysin ehjinä vuoden pidempään maksoi 37 euroa. Kun MS-tartunta oli saatu estettyä, korkean kariesriskin omaavien lasten hampaiden terveys oli samalla tasolla kuin keskimäärin koko ikäkohortilla. Lapsen maitohampaat säilyvät terveinä pidempään ja korjaavan hoidon tarve vähenee, kun MS-kolonisaatio alle 2-vuotiaana saadaan estettyä. Lapsen MS-kolonisaatio vähenee merkitsevästi, kun äiti käyttää ksylitolipurukumia lapsen ollessa 0-2 vuoden ikäinen, siten pikkulapsen äidin säännöllinen ksylitolipurukumin käyttö saattaa olla julkisen tereydenhuollon kannalta tarkoituksenmukainenterveyttä edistävä menetelmä.

Utilization of Incident Reporting in The Finnish Maritime Industry

Marine traffic is expected to increase rapidly in the future, both in the Baltic Sea and in the Gulf of Finland. As the number of vessels in the area increases, so does the risk of serious marine accidents. To help prevent such accidents in the future, the International Maritime Organization (IMO) has put forth the International Safety Management Code (the ISM Code), which aims to improve the safety of the vessels. The second work package of the Development of maritime safety culture (METKU) project investigates the effects of the ISM Code and potential areas of improvement in maritime safety. The first phase in the work package used a literature review to determine how maritime safety culture could be improved. Continuous improvement, management commitment and personnel empowerment and motivation were found to be essential. In the second phase, shipping companies and administrators were interviewed. It was discovered that especially incident reporting based on continuous improvement was felt to be lacking. This third phase aims to take a closer look at incident reporting and suggest improvements based on the findings. Both the IMO and national legislation encourage shipping companies in incident reporting, and on the national level a shared incident reporting system (ForeSea) is being pushed forward. The objective of this research project was to find out the IMO’s attitude towards incident reporting, to establish a theoretical framework of reference in incident reporting, and to observe how reporting is actually being employed on the seas. Existing incident reporting systems were also researched. The study was carried out using a literature review and the results previously gathered in interviews. The results of phase two were elaborated further for themes relating to incident reporting. According to the findings of this research, the theoretical background of incident reporting dates back to the early 20th century. Although some theories are widely accepted, some have also received criticism. The lack of a concise, shared terminology poses major difficulties in maritime incident reporting and in determining its efficiency. A central finding is the fact that existing incident reporting focuses mostly on information flow away from the ship, whereas the backward information flow is much less planned and monitored. In incident reporting, both nationally and internationally, stakeholders are plenty. The information produced by these parties is scattered, however, and thus not very usable. Based on this research, the centralizing of this information should be made a priority. Traditionally, the success of incident reporting has been determined statistically, from the number of reported incidents. Yet existing reporting systems have not been designed with such statistical analysis in mind, so different methodologies might yield a more comprehensive view. The previous findings of seafarers and management (including shipping companies and administration) having differing views on safety work and safety management were backed up by the results of this study. Seafarers find seamanship and storytelling important, while management wants a more systematic and broad approach on safety matters. The research project was carried out by the Centre for Maritime Studies of the University of Turku, in the Kotka unit (Maritime Logistics Research), with coordination by the Kotka Maritime Research Centre. The major financiers of the project were the European Union and the city of Kotka. The financing authority was the Regional Council of Päijät-Häme. Partners in the project were the shipping companies Finnlines Oyj, Kristina Cruises Oy, Meriaura Oy and VG-Shipping Oy, and the ports of Helsinki, Kotka and Hamina. The partners provided both funding for the project and information for the research.

Rigid Rod Polymer Fillers in Acrylic Denture and Dental Adhesive Resin Systems

Polymeric materials have been used in dental applications for decades. Adhesion of polymeric materials to each other and to the tooth substrate is essential to their successful use. The aim of this series of studies was two-folded. First, to improve adhesion of poly(paraphenylene) based rigid rod polymer (RRP) to other dental polymers, and secondly, to evaluate the usability of a new dentin primer system based on RRP fillers. Poly(paraphenylene) based RRP would be a tempting material for dental applications because of its good mechanical properties. To be used in dental applications, reliable adhesion between RRP and other dental polymers is required. In this series of studies, the adhesion of RRP to denture base polymer and the mechanical properties of RRP-denture base polymer-material combination were evaluated. Also adhesion of BisGMA-TEGDMA-resin to RRP was determined. Different surface treatments were tested to improve the adhesion of BisGMA-TEGDMA-resin to RRP. Results were based on three-point bending testing, Vickers surface hardness test and scanning electron microscope analysis (SEM), which showed that no reliable adhesion between RRP and denture base polymer was formed. Addition of RRP filler to denture base polymer increased surface hardness and flexural modulus but flexural strength decreased. Results from the shear bond strength test and SEM revealed that adhesion between resin and RRP was possible to improve by surface treatment with dichloromethane (DCM) based primer and a new kind of adhesive surface can be designed. The current dentin bonding agents have good immediate bond strength, but in long term the bond strength may decrease due to the detrimental effect of water and perhaps by matrix metalloproteinases. This leads to problems in longevity of restorations. Current bonding agents use organic monomers. In this series of studies, RRP filled dentin primer was tested in order to decrease the water sorption of the monomer system of the primers. The properties of new dentin primer system were evaluated in vitro by comparing it to commercial etch and rinse adhesive system. The results from the contact angle measurements and SEM showed that experimental primer with RRP reinforcement provided similar resin infiltration to dentin collagen and formed the resin-dentin interface as the control primer. Microtensile bond strength test and SEM revealed that in short term water storing, RRP increased bond strength and primer with BMEP-monomer (bis[2-(methacryloyloxy)-ethyl]phosphate) and high solvent concentration provided comparable bonding properties to the commercial control primers. In long term water storing, the high solvent-monomer concentration of the experimental primers decreased bond strength. However, in low solvent-monomer concentration groups, the long-term water storing did not decrease the bond strength despite the existence of hydrophilic monomers which were used in the system. These studies demonstrated that new dentin primer system reached the mechanical properties of current traditional etch and rinse adhesive system in short time water storing. Improved properties can be achieved by further modifications of the monomer system. Studies of the adhesion of RRP to other polymers suggest that adhesion between RRP and other dental polymers is possible to obtain by certain surface treatments.

The Influence of Certain Processing Factors on the Durability of Yttrium Stabilized Zirconia Used As Dental Biomaterial

In dentistry, yttrium partially stabilized zirconia (ZrO2) has become one of the most attractive ceramic materials for prosthetic applications. The aim of this series of studies was to evaluate whether certain treatments used in the manufacturing process, such as sintering time, color shading or heat treatment of zirconia affect the material properties. Another aim was to evaluate the load-bearing capacity and marginal fit of manually copy-milled custom-made versus prefabricated commercially available zirconia implant abutments. Mechanical properties such as flexural strength and surface microhardness were determined for green-stage milled and sintered yttrium partially stabilized zirconia after different sintering time, coloring process and heat treatments. Scanning electron microscope (SEM) was used for analyzing the possible changes in surface structure of zirconia material after reduced sintering time, coloring and heat treatments. Possible phase change from the tetragonal to the monoclinic phase was evaluated by X-ray diffraction analysis (XRD). The load-bearing capacity of different implant abutments was measured and the fit between abutment and implant replica was examined with SEM. The results of these studies showed that the shorter sintering time or the thermocycling did not affect the strength or surface microhardness of zirconia. Coloring of zirconia decreased strength compared to un-colored control zirconia, and some of the colored zirconia specimens also showed a decrease in surface microhardness. Coloring also affected the dimensions of zirconia. Significantly decreased shrinkage was found for colored zirconia specimens during sintering. Heat treatment of zirconia did not seem to affect materials’ mechanical properties but when a thin coating of wash and glaze porcelain was fired on the tensile side of the disc the flexural strength decreased significantly. Furthermore, it was found that thermocycling increased the monoclinic phase on the surface of the zirconia. Color shading or heat treatment did not seem to affect phase transformation but small monoclinic peaks were detected on the surface of the heat treated specimens with a thin coating of wash and glaze porcelain on the opposite side. Custom-made zirconia abutments showed comparable load-bearing capacity to the prefabricated commercially available zirconia abutments. However, the fit of the custom-made abutments was less satisfactory than that of the commercially available abutments. These studies suggest that zirconia is a durable material and other treatments than color shading used in the manufacturing process of zirconia bulk material does not affect the material’s strength. The decrease in strength and dimensional changes after color shading needs to be taken into account when fabricating zirconia substructures for fixed dental prostheses. Manually copy-milled custom-made abutments have acceptable load-bearing capacity but the marginal accuracy has to be evaluated carefully.

Virtual Professional Network as a Value Creator in the Dental Business

The research of virtual professional networks has been enormous but the lack of research in the dental field was obvious. This study focuses on those uses and gratifications, and motives of participants that a virtual pro-fessional network should fulfil. The aim of this study is to understand the factors behind the successful virtual professional network, and motives of participants that support a particular business network’s building up for contributing its further success. In this study the focus is on particular mo-tives, needs and benefits of participants that are significant for the net-work’s further development. The study will explore relevant scientific research and theory that is char-acteristic in networking, and theories of user’s needs and motives. Empiri-cal data was collected from dental professionals by net based question-naire that was sent by e-mail. Data analysis was done by quantitative fac-tor analysis. The findings of this study were obvious that virtual knowledge of implantology is inadequate and knowledge is rather difficult to find in the Internet. Sharing of virtual knowledge, net-learning and communication were seen to improve the quality of impolantological professionalism and also the development of these areas was experienced essential. On the grounds of this study a host of a virtual professional network can focus on those aspects that serve the users at best, can develop professionalism in implantology and can profit in its own business operations.

Carbohydrate intake in children - associations with dietary intakes, growth, serum lipids,and dental health. The STRIP Project

This study is part of the STRIP study, which is a long-term, randomized controlled trial, designed to decrease the exposure of children in the intervention group (n=540) to known risk factors of atherosclerosis. The main focus of the intervention was the quality of dietary fat. The control group (n=522) did not receive any individualized counselling. Food consumption was evaluated with food records, and blood samples were drawn and growth was measured regularly for all participating children from 13 months to 9 years. A subsample of 66 children participated in a dental health survey. The number of studies on children’s carbohydrate intake, especially fibre intake, is insufficient. The current international recommendations for fibre intake in children are based on average assumptions and data extrapolated from intakes in adults and intake recommendations for adults. Finnish nutrition recommendations lack strict recommendations for dietary fibre in children. Due to fibre’s high bulk volume, excessive dietary fibre is considered to decrease energy density and hence it may have an adverse effect on growth. If fats are reduced from the diet, the low-fat diet may become high in sucrose. Therefore, especially in the STRIP study, it is important to determine the use of fibre and sucrose in children and possible associations with growth and nutrition as well as dental health. The results of the present study indicate that a high fibre intake does not displace energy or disturb growth in children and that children with high fibre intake have better quality of diet than those with low fibre intake. Additionally, dietary fibre intake associated inversely with serum cholesterol concentration. Other carbohydrates also affected serum lipid levels as well, since total carbohydrates, sucrose, and fructose increased serum triglyceride concentration. Total carbohydrate intake reduced HDL cholesterol concentration only in children with apoE3 or apoE4 phenotype. Over the period from the 1970s to the 1990s the dental health of children in Finland has substantially improved despite an increase in sucrose intake. The improvement was thought to be due to improved dental hygiene and the use of fluorine. However, during the past twenty years improvement in dental health has stopped. The present study showed that high long-term sugar intake increases risk of caries in children. High intake of sugar had also negative effects on the diet of children, because it worsens dietary quality by displacing essential nutrients. Furthermore, the quality of dietary fat was worse in children with high sucrose intake. In this study the children’s high sucrose intake was not associated with overweight, but interestingly, it associated inversely with growth.

Utilization of Automatic Meter Reading in the Improvement of a District Heating System

A district heating system comprises production facilities, a distribution network, and heat consumers. The utilization of new energy metering and reading system (AMR) is increasing constantly in district heating systems. This heuristic study shows how the AMR system can be exploited in finding optimization opportunities in district heating system. In this study, the district heating system is mainly considered from the viewpoint of operational optimization. The focus is on the core processes, heat production and distribution. Three objectives were set to this study. The first one was to examine general optimization opportunities in district heating systems. Second, to figure out the benefits of AMR for general optimization opportunities. Finally, to define a methodology for process improvement endeavors. This study shows, through a case study, the usefulness of AMR in specifying current deficiencies in a district heating system. Based on a literature review, the methodology for the improvement of business processes is presented. Additionally, some issues related to future competitiveness of district heating are concerned. As a conclusion, some optimization objectives are considered more desirable than others. Study shows that AMR is useful in the specification of optimization targets in the district heating system. Further steps in optimization process were not examined in detail. That would seem to be interesting topic for further studies.

Utilization of Meat and bone meal for energy production

At the end of the 1990s the stock breeding in the Europe was suffering from the animal disease epidemics such as Bovine spongiform encephalopathy (BSE) and foot –and mouth disease. The European Union (EU) tackled to this problem by tightening the legislation of animal by-products. At this point, rendering and fat producing industries faces new challenges, which they have to cope with in a way of trying to find alternatives to their products (animal fats and meat and bone meal). One of the most promising alternatives to utilize these products was to use them in energy production purposes. The purpose of the Thesis was to examine the utilization possibilities of Meat and bone meal (MBM) for energy production. The first part of the Thesis consists of theory part. The theory part includes evaluation of basic properties of MBM as a fertilizer and as a fuel, legislative evaluation and evaluation of different burning techniques. The second part of the Thesis consists of burning tests in Energy laboratory of LUT with different mixtures of peat and MBM. The purpose of the burning tests was to identify co-firing possibilities of peat and MBM and emission- and ash properties for peat and MBM.

Customer reference marketing and utilization of social media as an integral part of customer references

The objective of this Bachelor's Thesis is to find out the role of social media in the B-to-B marketing environment of the information technology industry and to discover how IT-firms utilize social media as a part of their customer reference marketing. To reach the objectives the concepts of customer reference marketing and social media are determined. Customer reference marketing can be characterized as one of the most practically relevant but academically relatively overlooked ways in which a company can leverage its customers and delivered solutions and use them as references in its marketing activities. We will cover which external and internal functions customer references have, that contribute to the growth and performance of B-to-B firms. We also address the three mechanisms of customer reference marketing which are 'status transfer', 'validation through testimonials' and 'demonstration of experience and prior performance'. The concept of social media stands for social interaction and creation of user-based content which exclusively occurs through Internet. The social media are excellent tools for networking because of the fast and easy access, easy interaction and vast amount of multimedia attributes. The allocation of social media is determined. The case company helps clarify the specific characteristics of social media usage as part of customer-reference-marketing activities. For IT-firms the best channels to utilize social media in their customer reference marketing activities are publishing and distribution services of content and networking services.

Efficient installed base information management and utilization in global after sales service business

This Master´s thesis explores how the a global industrial corporation’s after sales service department should arrange its installed base management practices in order to maintain and utilize the installed base information effectively. Case company has product-related records, such as product’s lifecycle information, service history information and information about product’s performance. Information is collected and organized often case by case, therefore the systematic and effective use of installed base information is difficult also the overview of installed base is missing. The goal of the thesis study was to find out how the case company can improve the installed base maintenance and management practices and improve the installed base information availability and reliability. Installed base information management practices were first examined through the literature. The empirical research was conducted by the interviews and questionnaire survey, targeted to the case company’s service department. The research purpose was to find out the challenges related to case company´s service department’s information management practices. The study also identified the installed base information needs and improvement potential in the availability of information. Based on the empirical research findings, recommendations for improve installed base management practices and information availability were created. Grounding of the recommendations, the case company is suggested the following proposals for action: Service report development, improving the change management process, ensuring the quality of the product documentation in early stages of product life cycle and decision to improve installed base management practices.

Potential of utilization of rain water excess for irrigation of green roofs in Mato Grosso, Brasil

The aim of this study was to identify the relation between the evapotranspirometer demand and the supply of water from local rainfall, evaluating the possibility of using water excess for irrigation of Green Roofs in the State of Mato Grosso, in Brazil. The study was done using a series of historical data provided by the National Institute of Meteorology (INMET - Instituto Nacional de Meteorologia) which has official climatological stations in 12 cities and regions of the State. The evapotranspiration values were obtained by the Penman-Monteith method and by the Climatic Water Balance (CWB) by the Thornthwaite and Mather method using Available Water Capacity (AWC) of 12mm. With the CWB the excess and deficit were calculated, which were used for the estimative of the volume and area of a reservoir as a function of a collector area of a roof of 100m² and the volume of supplementary water for irrigation. With the obtained results, it was found that in most investigated regions of the State the use of green roofs is not compromised by the water deficiency. On the other hand, the use of a reservoir to accumulate the rain water excess may be impractical, because it requires a considerable area for installation and also because of the high cost of the land.

Customer satisfaction data utilization: identifying value drivers and information use practices

The objective of this master’s thesis was twofold: first to examine the concept of customer value and its drivers and second to identify information use practices. The first part of the study represents explorative research that was carried out by examining a case company’s customer satisfaction data that was used to identify sales and technical customer service related value drivers on a detailed attribute level. This was followed by an examination of whether these attributes had been commented on in a positive or a negative light and what were the reasons why the case company had received higher or lower ratings than its competitor. As a result a classification of different sales and technical customer service related attributes was created. The results indicated that the case company has performed well, but that the results varied on the company’s business segment level. The case company’s staff, service and the benefits from a long-lasting relationship came up in a positive light whereas attitude, flexibility and reaction time came up in a negative light. The reasons for a higher or lower score in comparison to competitor varied. The results indicated that a customer’s satisfaction with the company’s performance did not always mean that the company was outperforming the competition. The second part of the study focused on customer satisfaction information use from the viewpoints of information access, dissemination and reaction. The study was conducted by running an internal survey among the case company’s staff. The results showed that information use practices varied across the company and some units or teams had taken a more proactive approach to the information use than others.