Microwave-assisted enzymatic synthesis of beef tallow biodiesel

Optimal conditions for the microwave-assisted enzymatic synthesis of biodiesel have been developed by a full 2(2) factorial design leading to a set of seven runs with different combinations of molar ratio and temperature. The main goal was to reduce the reaction time preliminarily established by a process of conventional heating. Reactions yielding biodiesel, in which beef tallow and ethanol used as raw materials were catalyzed by lipase from Burkholderia cepacia immobilized on silica-PVA and microwave irradiations within the range of 8-15 W were performed to reach the reaction temperature. Under optimized conditions (1:6 molar ratio of beef tallow to ethanol molar ratio at 50A degrees C) almost total conversion of the fatty acid presented in the original beef tallow was converted into ethyl esters in a reaction that required 8 h, i.e., a productivity of about 92 mg ethyl esters g(-1) h(-1). This represents an increase of sixfold for the process carried out under conventional heating. In general, the process promises low energy demand and higher biodiesel productivity. The microwave assistance speeds up the enzyme catalyzed reactions, decreases the destructive effects on the enzyme of the operational conditions such as, higher temperature, stability, and specificity to its substrate, and allows the entire reaction medium to be heated uniformly.

SYNTHESIS OF N-15-ENRICHED UREA (CO((NH2)-N-15)(2)) FROM (NH3)-N-15, CO, AND S IN A DISCONTINUOUS PROCESS

CO((NH2)-N-15)(2) enriched with the stable isotope N-15 was synthesized based on a reaction involving CO, (NH3)-N-15, and S in the presence of CH3OH. The method differs from the industrial method; a stainless steel reactor internally lined with polytetrafluoroethylene (PTFE) was used in a discontinuous process under low pressure and temperature. The yield of the synthesis was evaluated as a function of the parameters: the amount of reagents, reaction time, addition of H2S, liquid solution and reaction temperature. The results showed that under optimum conditions (1.36, 4.01, and 4.48 g of (NH3)-N-15, CO, and S, respectively, 40 ml CH3OH, 40 mg H2S, 100 degrees C and 120 min of reaction) 1.82 g (yield 76.5%) of the compound was obtained per batch. The synthesized CO((NH2)-N-15)(2) contained 46.2% N, 0.55% biuret, melting point of 132.55 degrees C and did not exhibit isotopic fractionation. The production cost of CO((NH2)-N-15)(2) with 90.0 at. % N-15 was US$ 238.60 per gram.

Influence of cueing on the preparation and execution of untrained and trained complex motor responses

This study investigated the influence of cueing on the performance of untrained and trained complex motor responses. Healthy adults responded to a visual target by performing four sequential movements (complex response) or a single movement (simple response) of their middle finger. A visual cue preceded the target by an interval of 300, 1000, or 2000 ms. In Experiment 1, the complex and simple responses were not previously trained. During the testing session, the complex response pattern varied on a trial-by-trial basis following the indication provided by the visual cue. In Experiment 2, the complex response and the simple response were extensively trained beforehand. During the testing session, the trained complex response pattern was performed in all trials. The latency of the untrained and trained complex responses decreased from the short to the medium and long cue-target intervals. The latency of the complex response was longer than that of the simple response, except in the case of the trained responses and the long cue-target interval. These results suggest that the preparation of untrained complex responses cannot be completed in advance, this being possible, however, for trained complex responses when enough time is available. The duration of the 1st submovement, 1st pause and 2nd submovement of the untrained and the trained complex responses increased from the short to the long cue-target interval, suggesting that there is an increase of online programming of the response possibly related to the degree of certainty about the moment of target appearance.

Development of an enzymeless electroanalytical method for the indirect detection of creatinine in urine samples

The aim of this study is to develop a new enzymeless electroanalytical method for the indirect quantification of creatinine from urine sample. This method is based on the electrochemical monitoring of picrate anion reduction at a glassy carbon electrode in an alkaline medium before and after it has reacted with creatinine (Jaffe's reaction). By using the differential pulse voltammetry technique under the optimum experimental conditions (step potential, amplitude potential, reaction time, and temperature), a linear analytical curve was obtained for concentrations of creatinine ranging from 1 to 80 mu mol L-1, with a detection limit of 380 nmol L-1. This proposed method was used to measure creatinine in human urine without the interference of most common organic species normally present in biological fluids (e.g., uric acid, ascorbic acid, glucose, and phosphocreatinine). The results obtained using urine samples were highly similar to the results obtained using the reference spectrophotometric method (at a 95% confidence level). (C) 2012 Elsevier B.V. All rights reserved.

ANALYSIS OF THE BALANCE CONTROL IN SURFERS DURING THE ERECT POSTURE

Background: Surfing is a sport that has become considerably popular, which increased interest in research about the aspects that can influence on the performance of these athletes, such as injuries, aerobic fitness and reaction time. Due to the ever-changing environment and high instability required for surfing, the surfers must develop some neuromuscular skills (agility, balance, muscle strength and flexibility) to acquire better performance in this modality. Nevertheless, there are still few scientific studies concerned about the investigation of these motor skills in surfing. Objective: The aim of this study was to evaluate the balance control in surfers compared to practitioners of other physical activities. Methods: Participants remained on a force platform while performing tasks involving visual deprivation (eyes open or closed) and somatosensory disturbance (steady surface or use of foam), with covariation of experimental conditions. The following variables were analyzed: speed and root mean square (RMS) displacement of the center of pressure in the anteroposterior (AP) and mediolateral (ML) directions. Results: The results showed no difference between groups during the experimental conditions, that is to say, both surfers and the control group varied over the conditions of eyes closed and on foam. Conclusion: Although surfing requires the surfer to have great balance control, the results did not reveal a relationship between this sport and better performance in balance control. However, we must consider the small sample size and the fact that this sport requires dynamic balance, while the study evaluated static balance.

Cellulose micro/nanofibres from Eucalyptus kraft pulp: Preparation and properties

There is growing interest in cellulose nanofibres from renewable sources for several industrial applications. However, there is a lack of information about one of the most abundant cellulose pulps: bleached Eucalyptus kraft pulp. The objective of the present work was to obtain Eucalyptus cellulose micro/nanofibres by three different processes, namely: refining, sonication and acid hydrolysis of the cellulose pulp. The refining was limited by the low efficiency of isolated nanofibrils, while sonication was more effective for this purpose. However, the latter process occurred at the expense of considerable damage to the cellulose structure. The whiskers obtained by acid hydrolysis resulted in nanostructures with lower diameter and length, and high crystallinity. Increasing hydrolysis reaction time led to narrower and shorter whiskers, but increased the crystallinity index. The present work contributes to the different widespread methods used for the production of micro/nanofibres for different applications. (C) 2012 Elsevier Ltd. All rights reserved.

Facilitatory effects of an auditory warning stimulus in a visual location identification task and a visual shape identification task

The occurrence of a weak auditory warning stimulus increases the speed of the response to a subsequent visual target stimulus that must be identified. This facilitatory effect has been attributed to the temporal expectancy automatically induced by the warning stimulus. It has not been determined whether this results from a modulation of the stimulus identification process, the response selection process or both. The present study examined these possibilities. A group of 12 young adults performed a reaction time location identification task and another group of 12 young adults performed a reaction time shape identification task. A visual target stimulus was presented 1850 to 2350 ms plus a fixed interval (50, 100, 200, 400, 800, or 1600 ms, depending on the block) after the appearance of a fixation point, on its left or right side, above or below a virtual horizontal line passing through it. In half of the trials, a weak auditory warning stimulus (S1) appeared 50, 100, 200, 400, 800, or 1600 ms (according to the block) before the target stimulus (S2). Twelve trials were run for each condition. The S1 produced a facilitatory effect for the 200, 400, 800, and 1600 ms stimulus onset asynchronies (SOA) in the case of the side stimulus-response (S-R) corresponding condition, and for the 100 and 400 ms SOA in the case of the side S-R non-corresponding condition. Since these two conditions differ mainly by their response selection requirements, it is reasonable to conclude that automatic temporal expectancy influences the response selection process.

Componentes sensoriais e atencionais do tempo de reação: efeitos do tamanho, excentricidade e previsibilidade de estímulos visuais

A percepção visual depende do arcabouço sensorial e do processamento atencional. Este trabalho estudou o efeito, sobre o tempo de reação manual (TR), do tamanho, excentricidade e previsibilidade de estímulos visuais. No experimento 1 (n=8), um alvo foi apresentado aleatoriamente em uma de quatro excentricidades diferentes, possuindo três possíveis tamanhos. O experimento 2 (n=12) apresentava configuração similar, porém uma pista indicava o quadrante de maior probabilidade (70%) de apresentação do alvo. Os resultados mostraram um aumento do TR em função da excentricidade do alvo, além de uma diminuição do TR com o aumento do tamanho do alvo e indicação correta da pista. Uma análise das interações sugere uma superposição de mecanismos atencionais e puramente sensoriais compartilhando um estágio comum do processamento visual.

Synthesis of 15N-enriched urea (CO(15NH2)2) from 15NH3, CO, and S in a discontinuous process

CO(15NH2)2 enriched with the stable isotope 15N was synthesized based on a reaction involving CO, 15NH3, and S in the presence of CH3OH. The method differs from the industrial method; a stainless steel reactor internally lined with polytetrafluoroethylene (PTFE) was used in a discontinuous process under low pressure and temperature. The yield of the synthesis was evaluated as a function of the parameters: the amount of reagents, reaction time, addition of H2S, liquid solution and reaction temperature. The results showed that under optimum conditions (1.36, 4.01, and 4.48 g of 15NH3, CO, and S, respectively, 40 ml CH3OH, 40 mg H2S, 100 ºC and 120 min of reaction) 1.82 g (yield 76.5%) of the compound was obtained per batch. The synthesized CO(15NH2)2 contained 46.2% N, 0.55% biuret, melting point of 132.55 ºC and did not exhibit isotopic fractionation. The production cost of CO(15NH2)2 with 90.0 at. % 15N was US$ 238.60 per gram.

Preparation and characterisation of refractory whiskers and selected alumina composites

A whisker is a common name of single crystalline inorganic fibre of small dimensions, typically 0.5-1 μm in diameter and 20-50 μm in length. Whiskers are mainly used as reinforcement of ceramics. This work describes the synthesis and characterisation of new whisker types. Ti0.33Ta0.33Nb0.33CxN1-x, TiB2, B4C, and LaxCe1-xB6 have been prepared by carbothermal vapour–liquid–solid (CTR-VLS) growth mechanisms in the temperature range 900-1800°C, in argon or nitrogen. Generally, carbon and different suitable oxides were used as whisker precursors. The oxides reacted via a carbothermal reduction process. A halogenide salt was added to form gaseous metal halogenides or oxohalogenides and small amount of a transition metal was added to catalyse the whisker growth. In this mechanism, the whisker constituents are dissolved into the catalyst, in liquid phase, which becomes supersaturated. Then a whisker could nucleate and grow out under continuous feed of constituents. The syntheses of TiC, TiB2, and B4C were followed at ordinary synthesis conditions by means of mass spectrometry (MS), thermogravimetry (TG), differential thermal analysis (DTA) and quenching. The main reaction starting temperatures and reaction time for the different mixtures was revealed, and it was found that the temperature inside the crucible during the reactions was up to 100°C below the furnace set-point, due to endothermic nature of the reactions. Quench experiments showed that whiskers were formed already when reaching the temperature plateau, but the yield increased fast with the holding time and reached a maximum after about 20-30 minutes. Growth models for whisker formation have been proposed. Alumina based composites reinforced by (2-5 vol.%) TiCnano and TiNnano and 25 vol.% of carbide, and boride phases (whiskers and particulates of TiC, TiN, TaC, NbC, (Ti,Ta)C, (Ti,Ta,Nb)C, SiC, TiB2 and B4C) have been prepared by a developed aqueous colloidal processing route followed by hot pressing for 90 min at 1700°C, 28 MPa or SPS sintering for 5 minutes at 1200-1600°C and 75 MPa. Vickers indentation measurements showed that the lowest possible sintering temperature is to prefer from mechanical properties point of view. In the TiNnano composites the fracture mode was typically intergranular, while it was transgranular in the SiCnano composites. The whisker and particulate composites have been compared in terms of e.g. microstructure and mechanical properties. Generally, additions of whiskers yielded higher fracture toughness compared to particulates. Composites of commercially available SiC whiskers showed best mechanical properties with a low spread but all the other whisker phases, especially TiB2, exhibited a great potential as reinforcement materials.

Evaluación del tiempo de reacción en velocistas con discapacidad auditiva: estudio piloto

[ES] Este artículo tiene por objeto conocer las posibles diferencias del tiempo de reacción visual (TRV) desde los tacos de salida en velocistas con discapacidad auditiva, usando para dicha salida un estímulo visual mediante un dispositivo luminoso coordinado con la señal sonora de salida.

Il ruolo del collicolo superiore nell'orientamento spaziale

This thesis was aimed at verifying the role of the superior colliculus (SC) in human spatial orienting. To do so, subjects performed two experimental tasks that have been shown to involve SC’s activation in animals, that is a multisensory integration task (Experiment 1 and 2) and a visual target selection task (Experiment 3). To investigate this topic in humans, we took advantage of neurophysiological finding revealing that retinal S-cones do not send projections to the collicular and magnocellular pathway. In the Experiment 1, subjects performed a simple reaction-time task in which they were required to respond as quickly as possible to any sensory stimulus (visual, auditory or bimodal audio-visual). The visual stimulus could be an S-cone stimulus (invisible to the collicular and magnocellular pathway) or a long wavelength stimulus (visible to the SC). Results showed that when using S-cone stimuli, RTs distribution was simply explained by probability summation, indicating that the redundant auditory and visual channels are independent. Conversely, with red long-wavelength stimuli, visible to the SC, the RTs distribution was related to nonlinear neural summation, which constitutes evidence of integration of different sensory information. We also demonstrate that when AV stimuli were presented at fixation, so that the spatial orienting component of the task was reduced, neural summation was possible regardless of stimulus color. Together, these findings provide support for a pivotal role of the SC in mediating multisensory spatial integration in humans, when behavior involves spatial orienting responses. Since previous studies have shown an anatomical asymmetry of fibres projecting to the SC from the hemiretinas, the Experiment 2 was aimed at investigating temporo-nasal asymmetry in multisensory integration. To do so, subjects performed monocularly the same task shown in the Experiment 1. When spatially coincident audio-visual stimuli were visible to the SC (i.e. red stimuli), the RTE depended on a neural coactivation mechanism, suggesting an integration of multisensory information. When using stimuli invisible to the SC (i.e. purple stimuli), the RTE depended only on a simple statistical facilitation effect, in which the two sensory stimuli were processed by independent channels. Finally, we demonstrate that the multisensory integration effect was stronger for stimuli presented to the temporal hemifield than to the nasal hemifield. Taken together, these findings suggested that multisensory stimulation can be differentially effective depending on specific stimulus parameters. The Experiment 3 was aimed at verifying the role of the SC in target selection by using a color-oddity search task, comprising stimuli either visible or invisible to the collicular and magnocellular pathways. Subjects were required to make a saccade toward a target that could be presented alone or with three distractors of another color (either S-cone or long-wavelength). When using S-cone distractors, invisible to the SC, localization errors were similar to those observed in the distractor-free condition. Conversely, with long-wavelength distractors, visible to the SC, saccadic localization error and variability were significantly greater than in either the distractor-free condition or the S-cone distractors condition. Our results clearly indicate that the SC plays a direct role in visual target selection in humans. Overall, our results indicate that the SC plays an important role in mediating spatial orienting responses both when required covert (Experiments 1 and 2) and overt orienting (Experiment 3).

Synthese und Charakterisierung von Poly(tert-butylacrylat)- und Polyacrylsäure-Sternpolymeren

Sternpolymere aus Poly(tert.-butylacrylat)-Armen und einem Mikrogel-Core aus Ethylenglykoldimethacrylat wurden nach der arm-first Strategie hergestellt. Diese weisen eine enge Armzahlverteilung auf. Mit sinkender Precursorlänge, mit steigendem Verhältnis [bifunktionelles Monomer]/[Initiator], sowie mit zunehmender Reaktionszeit und Gesamtkonzentration nimmt die mittlere Armzahl fn zu. Die Sternbildung verläuft ähnlich einer Polykondensation. Die Molekulargewichte wurden mittels GPC gekoppelt mit einem online-Viskosimeter und einem online-Vielwinkellichtstreudetektor (MALLS) bestimmt.Die intrinsischen Viskositäten der Sternpolymere sind sehr niedrig. Für Armzahlen f ca. 8 erhält man ein Maximum in der doppellogarithmischen Auftragung der intrinsischen Viskosität und des Molekulargewichts. Die Trägheitsradien nehmen nur wenig mit dem Molekulargewicht zu. Die erhaltenen Koeffizienten liegen im von Daoud und Cotton vorhergesagten Bereich. Die Schrumpfungsfaktoren sinken auf g ca. 0,2 bzw. g' ca. 0,25. Aus den Poly(tert.-butylacrylat)-Sternpolymeren wurden durch Verseifung mit HBr in Methanol Polyacrylsäure-Sternpolymere hergestellt, welche ebenfalls mittels GPC-Viskosimetrie und GPC-MALLS charakterisiert wurden. Für die ionischen Sternpolymere findet man deutlich höhere Schrumpfungsfaktoren, kein Maximum in der intrinsischen Viskosität und höhere Exponenten als von Daoud und Cotton vorhergesagt. Erklärt wurde dies mit der hohen Segmentdichte in Sternpolymeren, die bei den ionischen Sternpolymeren zu einer hohen Ladungsdichte führt. Dadurch müssen sich die Arme stärker strecken als bei nicht-ionischen Sternen und es resultieren größere Moleküldimensionen.

Zeitaufgelöste Fluoreszenzmessungen zur Faltung und Pigmentbindung des Lichtsammlerproteins LHC II aus Photosystem II

Zusammenfassung Der Lichtsammlerkomplex (LHCII) aus PhotosystemII hoeherer Pflanzen kann in vitro rekonstituiert werden. Es werden drei Reaktionszeiten (<10 s; <1 min; <10 min) aufgeloest. Dabei werden bei allen Reaktionszeiten Pigmente durch das Apoprotein gebunden. Chlorophylle (Chl a und Chl b) und Xanthophylle wirken limitierend auf die Rekonstitution. Chl a beschleunigt die zweite Reaktionszeit, ein ausgeglichenes Chl a/b-Verhaeltnis verkürzt die dritte Reaktionszeit. Ein molekularer Mechanismus als Interpretation dieser Effekte wird vorgeschlagen. Native Lipide verlaengern nichtspezifisch die Rekonstitution. Abiotische Faktoren haben einen spezifischen Einfluss auf die Rekonstitution. Spezifische Einfluesse der o. a. Bedingungen auf die thermische Stabilitaet des rekonstituierten LHCII wurden bestimmt.

Hyperverzweigte Polyphenylene und redoxaktive Dendrimere

Die Doktorarbeit gliedert sich in zwei Abschnitte. Das erste Kapitel beschäftigt sich mit den hyperverzweigten Polyphenylenen. Es wurden Untersuchungen des Molekulargewichts in Abhängigkeit von der Monomerkonzentration und der Reaktionszeit durchgeführt. Die synthetisierten Polymere haben große Polydispersitäten, die durch fraktioniertes Fällen herabgesetzt werden können. Die Funktionalisierung der hyperverzweigten Polyphenylene mit unterschiedlichen Methoden führt zu verschiedenen Funktionen auf der Oberfläche der Polymere. Die chlormethylierten hyperverzweigen Polymere können als Makroinitiator für den Aufbau von Kern-Schale-Systemen genutzt werden. Mit Hilfe der ATRP-Polymerisation wurde Methylmethacrylat anpolymerisiert. Als Charakterisierungsmethode zur Bestimmung des freien Volumens findet die Positronenauslöschungsspektroskopie Anwendung. Im zweiten Teil der Arbeit stehen die Synthese und Charakterisierung von redoxaktiven Dendrimeren mit Triphenylamin- bzw. Naphthalinkern im Mittelpunkt. Den Einfluß der Dendrimerhülle auf die Redoxaktivität zeigen cyclovoltammetrische Untersuchungen. Die Zunahme der dendritischen Hülle führt zu einer Abschirmung des Redoxzentrums gegen die Elektrode und damit zu einer Inhibierung des Elektronentransfers. Das spiegelt sich in der Abnahme der Geschwindigkeitskonstanten sowie in der Ausdehnung der cyclovoltammetrischen Kurve wieder. Die Funktionalisierung der Triphenylamin-Dendrimere mit Chromophoren auf der Oberfläche führt zu einer Änderung der optische Eigenschaften, die mit Hilfe von Absorptions- und Emissionsmessungen untersucht wurden.