一种新型绿敏光致聚合物及全息特性研究

报道了一种新型的对绿光敏感的光致聚合物材料，对环境湿度不敏感，材料的干燥时间短。该材料以丙烯酰胺为单体，N-苯基甘氨酸作为引发剂，藻红B作为光敏剂，并加入成膜剂聚乙烯醇及增塑剂二甲亚砜。对材料中光引发剂、光敏剂及增塑剂浓度进行了优化，发现其有一个最佳值。本材料记录的全息图衍射效率可达50％以上，感光强度为60mJ／cm^2。在光聚物介质上能够记录信噪比比较高的图像，说明该材料可用于全息存储。

光致聚合物中单体及粘结剂对全息性能的影响

研究了单体及粘结剂等成份对全息光致聚合物薄膜光存储性能的影响。在相同引发条件下．以丙烯酰胺作为单体时，光聚物的衍射效率明显高于以丙烯酸和N羟甲基丙烯酰胺作为单体时光聚物的衍射效率。向丙烯酰胺中加入少量N-羟甲基丙烯酰胺，可以改善膜表面的光学质量．降低散射光强度，并提高膜的保存时间。在聚乙烯醇膜中单体聚合程度明显优于在聚乙烯吡咯烷酮中的程度，在大分子量的聚乙烯醇中的衍射效率及感光灵敏度高于在小分子量中的衍射效率和感光灵敏度，而且大分子量的聚乙烯醇能够制备厚膜，这是实现全息海量存储的一个重要因素。

沢吨染料的光化漂白动力学及全息特性研究

研究了以三乙醇胺作为引发剂,五种沢吨染料的光化漂白过程.实验结果表明五种染料的光化漂白速率大小顺序是藻红B（ErB）＞曙红Y（EY）＞孟加拉玫瑰红B（RsB）＞罗丹明B（RoB）＞荧光素（F）.并研究了曝光强度及染料浓度对漂白过程的影响,以及这五种染料的全息记录性能.

双染料敏化的光致聚合物全息特性研究

报道了一种新型、双染料共同敏化的光致聚合物材料,该材料以丙稀酰胺和双丙稀酰胺作为单体,聚乙烯醇为聚合物基质,两种染料曙红Y和亚甲基蓝作为光引发剂.实验结果表明,该材料在四种波长的激光照射下,其最大衍射效率均不低于25%,最大可达54.8%.通过采用多波长存储技术,分别利用四种不同波长的光在该聚合物膜上同一位置存储了四幅不同的图像,取得一定的效果.

光纤耦合波长复用的全息光盘存储记录

详细描述了用光纤耦合、波长复用的全息光盘仔储光路．指出在全息光盘驱动器即将市场化的今天．由于其光路简单、光学元件较少、性价比高．很有可能成为新的全息光盘驱动器的核心技术之一。由于短波长单模光纤及其双波长光纤分束器件的要求比较高．而用多模光纤进行准单模输出调整．以及用分光棱镜进行光束的分光．同时用对双波长敏感的光致聚合物材料进行存储．其光谱灵敏度均匀．光谱范围互不重叠。实验结果表明．光路结构合理．存储效果良好。

一种核黄素敏化的宽带全息记录材料

制备了一种核黄素敏化的以聚乙烯醇为基质的新型全息存储材料，并研究了材料的全息特性,用Ar^＋激光器激发的488nm的蓝光对材料曝光，结果表明该材料具有较高的衍射效率和曝光灵敏度，衍射效率高达53％，灵敏度为3．3cm^2／J，折射率调制度为4．5×10^-4研究了材料的透过率与随时间和入射角度变化的关系，说明在曝光记录过程中有噪音光栅生成．在存储介质膜中存储了全息图像，再现图像较为清晰，说明该材料适合用作高密度全息存储介质．

Study on eight-pass dual-frequency laser interferometer with nanometer precision

A new dual-frequency laser displacement measurement interferometer with nanometer precision has been developed. An eight-pass optical subdivision technology is proposed to improve resolution based on commercial interferometers. A static positioning error measuring method has been used to examine the precision and repeatability of the laser interferometer. An optical resolution of 1.24 nm and an accuracy of nanometer scale have been achieved.

外差干涉仪混频误差分析

共光路外差干涉仪具有很高的分辨率．但因为安装、调试误差会产生非线性误差．影响系统的测量精度。着重分析了在共光路外差干涉仪中由激光光源的椭圆偏振化和沃拉斯顿棱镜的安装方位角误差同时存在的情况下，引起的频率混叠综合误差的大小及变化规律。结果发现其造成的非线性误差可达2．2nm，同时还发现两者造成的误差在某些情况下存在一定程度的相互抵消作用。讨论了提高测量系统精度的有效措施，对正确设计和调试激光外差测试系统、提高测量系统精度具有重要意义。

加速度对激光双频干涉仪测量误差的影响

为了减少由于加速度所导致的激光双频干涉仪测量误差,引入二阶多普勒频移,建立了由被测物体加速度所引起的测量误差的理论模型。仿真结果表明,在0.4s时间内0.6g加速度所引起的累积误差可达2.5 nm左右,这对于纳米精度的测量是不应忽视的; 初速度不为零时加速运动会引起更大的误差,而减速运动所引起的误差则相对小。通过实验验证,所测的误差变化趋势与理论模拟比较吻合。

Design and properties analysis of multi-layer dielectric used in pulse compressor gratings

Used in chirped-pulse amplification system and based on multi-layer thin film stack, pulse compressor gratings (PCG) are etched by ion-beam and holographic techniques. Diffraction efficiency and laser-induced damage threshold rely on the structural parameters of gratings. On the other hand, they depend greatly on the design of multi-layer. A theoretic design is given for dielectric multi-layer, which is exposed at 413.1 nm and used at 1053 nm. The influences of coating design on optical characters are described in detail. The analysis shows that a coating stack of H3L (H2L) (boolean AND) 9H0.5L2.01H meets the specifications of PCG well. And there is good agreement of transmission between experimental and the theoretic design. (c) 2005 Elsevier GmbH. All rights reserved.

脉宽压缩光栅用的多层膜设计和性能分析

应用于啁啾脉冲放大技术中的脉宽压缩光栅是基于多层膜作为基底，利用全息干涉技术和离子束技术刻蚀而成。脉宽压缩光栅的衍射效率和抗激光损伤阈值一方面依赖于光栅结构的设计，另一方面很大程度上取决于作为基底的多层膜的设计。给出了以413．1nm作为写入波长，1053nm作为使用波长的多层介质光栅膜的设计．样品在ZZS-800F、型真空镀膜机上采用电子束蒸发方式沉积而成，并给出了膜系结构对光学性能影响因素的详细分析，结果表明膜系H3L(H2L)^9H0．5L2．03H满足光栅膜的指标。给出了样品光学特性测试，其使用波

Interfacial immobilization of monoclonal antibody and detection of human prostate-specific antigen.

Antibody orientation and its antigen binding efficiency at interface are of particular interest in many immunoassays and biosensor applications. In this paper, spectroscopic ellipsometry (SE), neutron reflection (NR), and dual polarization interferometry (DPI) have been used to investigate interfacial assembly of the antibody [mouse monoclonal anti-human prostate-specific antigen (anti-hPSA)] at the silicon oxide/water interface and subsequent antigen binding. It was found that the mass density of antibody adsorbed at the interface increased with solution concentration and adsorption time while the antigen binding efficiency showed a steady decline with increasing antibody amount at the interface over the concentration range studied. The amount of antigen bound to the interfacial immobilized antibody reached a maximum when the surface-adsorbed amount of antibody was around 1.5 mg/m(2). This phenomenon is well interpreted by the interfacial structural packing or crowding. NR revealed that the Y-shaped antibody laid flat on the interface at low surface mass density with a thickness around 40 Å, equivalent to the short axial length of the antibody molecule. The loose packing of the antibody within this range resulted in better antigen binding efficiency, while the subsequent increase of surface-adsorbed amount led to the crowding or overlapping of antibody fragments, hence reducing the antigen binding due to the steric hindrance. In situ studies of antigen binding by both NR and DPI demonstrated that the antigen inserted into the antibody layer rather than forming an additional layer on the top. Stability assaying revealed that the antibody immobilized at the silica surface remained stable and active over the monitoring period of 4 months. These results are useful in forming a general understanding of antibody interfacial behavior and particularly relevant to the control of their activity and stability in biosensor development.

The silicon backplane design for an LCOS polarization-insensitive phase hologram SLM

Polarization-insensitivity is achieved in a reflective spatial light modulator by laying a quarter-wave plate (QWP) at the incident wavelength directly over the mirror pixels of a silicon backplane, and forming a nematle Fréedrickcz cell over the QWP to modulate the reflected phase. To achieve the highest drive voltage from the available silicon process, a switched voltage common front electrode design is described, with variable amplitude square wave drive to the pixels to maintain constant root-mean-square drive and minimize phase fluctuations during the dc balance refresh cycle. The silicon has been fabricated and liquid-crystal-on-silicon cells both with and without the QWP assembled; applications include optically transparent switches for optical networks, beam steering for add-drop multiplexers for wavelength-division- multiplexing telecommunications, television multicast, and holographic projection.

Ink-jet printing for patterning engineering surfaces

This work explored the use of industrial drop-on-demand inkjet printing for masking steel surfaces on engineering components, followed by chemical etching, to produce patterned surfaces. A solvent-based ink was printed on to mild steel samples and the influences of substrate topography and substrate temperature were investigated. Contact angle measurements were used to assess wettability. Regular patterns of circular spots (∼60 /on diameter) and more complex mask patterns were printed. Variation of the substrate temperature had negligible effect on the final size of the printed drops or on the resolution achieved. Colored optical interference fringes were observed on the dried ink deposits and correlated with film thickness measurements by whitelight interferometry.

Modal liquid crystal devices in optical tweezing: 3D control and oscillating potential wells

We investigate the use of liquid crystal (LC) adaptive optics elements to provide full 3 dimensional particle control in an optical tweezer. These devices are suitable for single controllable traps, and so are less versatile than many of the competing technologies which can be used to control multiple particles. However, they have the advantages of simplicity and light efficiency. Furthermore, compared to binary holographic optical traps they have increased positional accuracy. The transmissive LC devices could be retro-fitted to an existing microscope system. An adaptive modal LC lens is used to vary the z-focal position over a range of up to 100 μm and an adaptive LC beam-steering device is used to deflect the beam (and trapped particle) in the x-y plane within an available radius of 10 μm. Furthermore, by modifying the polarisation of the incident light, these LC components also offer the opportunity for the creation of dual optical traps of controllable depth and separation. © 2006 Optical Society of America.