Two-phase flow patterns and pressure drop inside horizontal tubes containing twisted-tape inserts

This paper presents an experimental study on two-phase flow patterns and pressure drop of R134a inside a 15.9 mm ID tube containing twisted-tape inserts. Experimental results were obtained in a horizontal test section for twisted-tape ratios of 3, 4, 9 and 14, mass velocities ranging from 75 to 250 kg/m(2) s and saturation temperatures of 5 and 15 degrees C. An unprecedented discussion on two-phase flow patterns inside tubes containing twisted-tape inserts is presented and the flow pattern effects on the frictional pressure drop are carefully discussed. Additionally, a new method to predict the frictional pressure drop during two-phase flow inside tubes containing twisted-tape inserts is proposed. (C) 2012 Elsevier Ltd. All rights reserved.

Nanogravimetric study of lead underpotential deposition on selenium thin films as a semiconductor alloy formation procedure

An electrochemical quartz crystal microbalance Au electrode modified with a Se thin film was used to investigate the electrochemical behavior of lead ad-atoms using underpotential deposition (UPD) conditions. A specific quasi-reversible process was observed during the reduction of Pb2+ on Se thin films in perchloric acid media. The charge density of Pb ad-atoms on Se thin film (46.86 mu C cm(-2)) suggests a recovery of 0.1 monolayers, which is in good agreement with EQCM data. The Se thin film can be successfully alloyed with Pb atoms that are deposited by chronoamperometry using time intervals large enough to allow for diffusion toward the inner Se phase. Linear sweep voltammetry combined with EQCM in perchloric acid was used to characterize the amount of Pb absorbed in the Se thin film. These findings offer a new strategy for alloy formation in semiconductor films using UPD as an effective tool to quantify the exact amount of the incorporated metal.

Two-Phase Frictional Pressure Drop and Flow Boiling Heat Transfer for R245fa in a 2.32-mm Tube

Experimental two-phase frictional pressure drop and flow boiling heat transfer results are presented for a horizontal 2.32-mm ID stainless-steel tube using R245fa as working fluid. The frictional pressure drop data was obtained under adiabatic and diabatic conditions. Experiments were performed for mass velocities ranging from 100 to 700 kg m−2 s−1 , heat flux from 0 to 55 kW m−2 , exit saturation temperatures of 31 and 41◦C, and vapor qualities from 0.10 to 0.99. Pressures drop gradients and heat transfer coefficients ranging from 1 to 70 kPa m−1 and from 1 to 7 kW m−2 K−1 were measured. It was found that the heat transfer coefficient is a strong function of the heat flux, mass velocity, and vapor quality. Five frictional pressure drop predictive methods were compared against the experimental database. The Cioncolini et al. (2009) method was found to work the best. Six flow boiling heat transfer predictive methods were also compared against the present database. Liu and Winterton (1991), Zhang et al. (2004), and Saitoh et al. (2007) were ranked as the best methods. They predicted the experimental flow boiling heat transfer data with an average error around 19%.

Molecular origin of charge traps in polyfluorene-based semiconductors

The comprehensive control of morphology and structure is of extreme importance in semiconducting polymers when used as active layers in optoelectronic devices. In the work reported here, a systematic investigation of the structural and dynamical properties of poly(9,9-di-n-octyl-fluorene-alt-benzothiadiazole), known as F8BT, and their correlation with electrical properties is presented when the material is used as an active layer in optoelectronic devices. By means of X-ray diffraction, one observes that in thick layer films (thickness of about 4 μm) grown by drop-cast deposition, a solvent induced crystalline phase exists which evolves to a stable phase as the temperature is raised. This was not observed in thin films (thickness of about 250 nm) prepared by spin-coating within the investigated temperature range. By modeling the current-voltages characteristics of both thick and thin film devices, important information on the influence of crystallization on the trapping states could be drawn. Furthermore, the temperature dependence of the charge carrier mobility was found to be closely related to that of the molecular relaxation processes. The understanding of the nature of such molecular relaxations, measured by solid-state nuclear magnetic resonance methods, allows one to understand the importance of molecular relaxations and microstructure changes on the trap states of the system.

Influence of the network modifier on the characteristics of MSnO3 (M=Sr and Ca) thin films synthesized by chemical solution deposition

CaSnO3 and SrSnO3 alkaline earth stannate thin films were prepared by chemical solution deposition using the polymeric precursor method on various single crystal substrates (R- and C-sapphire and 100-SrTiO3) at different temperatures. The films were characterized by X-ray diffraction (θ-2θ, ω- and φ-scans), field emission scanning electron microscopy, atomic force microscopy, micro-Raman spectroscopy and photoluminescence. Epitaxial SrSnO3 and CaSnO3 thin films were obtained on SrTiO3 with a high crystalline quality. The long-range symmetry promoted a short-range disorder which led to photoluminescence in the epitaxial films. In contrast, the films deposited on sapphire exhibited a random polycrystalline growth with no meaningful emission regardless of the substrate orientation. The network modifier (Ca or Sr) and the substrate (sapphire or SrTiO3) influenced the crystallization process and/or the microstructure. Higher is the tilts of the SnO6 octahedra, as in CaSnO3, higher is the crystallization temperature, which changed also the nucleation/grain growth process.

Effect of a polymeric protective coating on optical and electrical properties of poly (p-phenylene vinylene) derivatives

The resistance to photodegradation of poly [(2-methoxy-5-n-hexyloxy)-p-phenylene vinylene] (OC1OC6-PPV) films was significantly enhanced by the use of poly(vinyl alcohol) 99% hydrolyzed as protective coating. The deposition of poly(vinyl alcohol) onto OC1OC6-PPV films did not affect the absorption and the emission spectra of the luminescent polymer. The protected film showed 5% drop on the absorbance at 500nm after 270 hours of light exposure while the unprotected film completely degraded in the same conditions. The conductivity of the protected film remained stable (around 7 × 10-10 S/m) while the value for the unprotected one dropped around two orders of magnitude after 100 hours of light exposure.

In-situ-Präparation von komplexen supraleitenden und ferroelektrischen Heterostrukturen mittels gepulster Laser-Deposition

In der vorliegenden Arbeit ist die Konstruktion und der Aufbau eines Systems zur gepulsten Laserablation von dünnen Schichten beschrieben. Die hohe Flexibilität der Anlage wird ermöglicht durch einen sechsfach-Targethalter und eine Heizerkonstruktion, die einfachen Substrateinbau, hohe Temperaturhomogenität und einen zugänglichen Temperaturbereich von bis zu 1000°C erlaubt. Durch eine komplexe Laser-Optik, die eine homogene Energiedichte auf dem Target sicherstellt, wird eine optimale Filmqualität erreicht.Durch die Entwicklung einer zweistufigen Prozeßführung für Y-stabilisiertes ZrO2 wird eine Wachstumsbasis hoher kristalliner Qualität für funktionale Oxidschichten auf Silizium zur Verfügung gestellt. Es zeigt sich, daß die dielektrischen Eigenschaften der YSZ Schicht stark vom Sauerstoffgehalt, der Grenzflächenmorphologie sowie der Dicke der ersten Schicht abhängig sind. Basierend auf dieser Schicht wurde BaZrO3 als zusätzliche Pufferschicht für den Hochtemperatursupraleiter (HTSL) YBa2Cu3O7 ? untersucht. Unter Verwendung von SrTiO3 Substraten konnte die dielektrische Konstante von BaZrO3 zu ? ? 65 bestimmt sowie das Dispersionsverhalten mittels modifizierter Debye-Gleichungen erklärt werden. Vergleichende Messungen auf einkristallinen SrTiO3 Substraten zeigen eine erhöhte Übergangstemperatur von 90.2 K und eine wesentliche Verbesserung der Oberflächenrauhigkeit des HTSL von 2 nm (rms) durch die Verwendung von BaZrO3 Schichten hoher Qualität. Eine nur wenige Monolagen dicke zusätzliche BaZrO3 Pufferschicht auf YSZ-gepufferten Silizium Substraten verhindert die Ausbildung von ?9° rotierten YBCO Körnern, die üblicherweise bei der direkten Deposition auf YSZ beobachtet werden. Resistive Messungen mit Übergangstemperaturen oberhalb 89 K sind vergleichbar zu Ergebnissen, die für CeO2/YSZ Pufferschichtkombinationen erreicht werden. Durch kontinuierliche Gitteranpassung wurde eine neue Schichtabfolge YBCO/CeO2/YSZ/BaZrO3 für die Erzeugung bi-epitaxialer Korngrenzen-Josephson Kontake gefunden und deren Epitaxiebeziehungen geklärt. Eine in-situ deponierte Schichtabfolge zeigt mit einer Übergangstemperatur von 91.7 K und einer Übergangsbreite von 0.15 K supraleitende Eigenschaften vergleichbar zu den besten bisher auf diesem Gebiet erreichten Ergebnissen. Voruntersuchungen zur Realisierung eines Josephsonkontaktes mit dieser Schichtabfolge zeigen jedoch, daß die erreichten Eigenschaften für die technologische Anwendung nicht ausreichend sind.Die Verwendung einer YSZ/CeO2 Pufferschichtkombination ermöglicht die Herstellung von c Achsen orientiertem ferroelektrischem SrBi2Ta2O9 auf Silizium. Im Gegensatz hierzu führt die direkte Deposition auf Silizium zu polykristallinem SrBi2Ta2O9 oder zur Ausbildung der Pyrochlor Phase, wenn nur YSZ als Pufferschicht verwendet wird. Obwohl die Polarisierung von SrBi2Ta2O9 in der ab-Ebene liegt, konnte in MFIS Strukturen ein Speicherfenster von maximal 0.87 V beobachtet werden, was eine Verbesserung um nahezu einen Faktor drei im Vergleich zu polykristallinem SrBi2Ta2O9 bedeutet. Messungen an ferroelektrischen Kondesatorstrukturen ergeben Hystereseschleifen mit einer remanenten Polarisierung von Pr = 6.5 µC/cm2 sowie einem Koerzitivfeld von Ec = 35 kV/cm. AFM Messungen im Piezo-Response Modus zeigen ferroelektrische Domänen, die durch Anlegen einer Gleichspannung reversibel umpolarisiert werden können. Im Nicht-Kontakt AFM Modus wurde die lokale Polarisierung der Schichten zu 3.4 µC/cm2 bestimmt. Weiterhin wurde eine alternative Pufferschichtkombination SrZrO3/YSZ zur Erzeugung von a-Achsen orientiertem SrBi2Ta2O9 untersucht. SrZrO3 zeigt a Achsen Orientierung in vier Wachstumsdomänen, die durch ein Model erklärt werden können. Die SrBi2Ta2O9 Schicht zeigt a Achsen sowie (116)-orientierte Körner mit derselben Domänenstruktur. Die dielektrische Konstanten von SrZrO3 und SrBi2Ta2O9 wurden zu ? ? 29 und ? ? 20 bestimmt. Die beobachteten Speicherfenster sind allerdings nicht ferroelektrischer Natur, sondern wahrscheinlich durch mobile Ionen und Ladungsfangstellen in den Pufferschichten verursacht. Die stark abgesenkte dielektrische Konstante von SrBi2Ta2O9 kann durch die im Vergleich zu polykristallinem verkleinerte Korngröße erklärt werden.

Modelling the effects of nitrogen deposition and carbon dioxide enrichment on forest carbon balance

Atmospheric CO2 concentration ([CO2]) has increased over the last 250 years, mainly due to human activities. Of total anthropogenic emissions, almost 31% has been sequestered by the terrestrial biosphere. A considerable contribution to this sink comes from temperate and boreal forest ecosystems of the northern hemisphere, which contain a large amount of carbon (C) stored as biomass and soil organic matter. Several potential drivers for this forest C sequestration have been proposed, including increasing atmospheric [CO2], temperature, nitrogen (N) deposition and changes in management practices. However, it is not known which of these drivers are most important. The overall aim of this thesis project was to develop a simple ecosystem model which explicitly incorporates our best understanding of the mechanisms by which these drivers affect forest C storage, and to use this model to investigate the sensitivity of the forest ecosystem to these drivers. I firstly developed a version of the Generic Decomposition and Yield (G’DAY) model to explicitly investigate the mechanisms leading to forest C sequestration following N deposition. Specifically, I modified the G’DAY model to include advances in understanding of C allocation, canopy N uptake, and leaf trait relationships. I also incorporated a simple forest management practice subroutine. Secondly, I investigated the effect of CO2 fertilization on forest productivity with relation to the soil N availability feedback. I modified the model to allow it to simulate short-term responses of deciduous forests to environmental drivers, and applied it to data from a large-scale forest Free-Air CO2 Enrichment (FACE) experiment. Finally, I used the model to investigate the combined effects of recent observed changes in atmospheric [CO2], N deposition, and climate on a European forest stand. The model developed in my thesis project was an effective tool for analysis of effects of environmental drivers on forest ecosystem C storage. Key results from model simulations include: (i) N availability has a major role in forest ecosystem C sequestration; (ii) atmospheric N deposition is an important driver of N availability on short and long time-scales; (iii) rising temperature increases C storage by enhancing soil N availability and (iv) increasing [CO2] significantly affects forest growth and C storage only when N availability is not limiting.

Candidate genes affecting fat deposition, carcass composition and meat quality traits in pigs

Pig meat quality is determined by several parameters, such as lipid content, tenderness, water-holding capacity, pH, color and flavor, that affect consumers’ acceptance and technological properties of meat. Carcass quality parameters are important for the production of fresh and dry-cure high-quality products, in particular the fat deposition and the lean cut yield. The identification of genes and markers associated with meat and carcass quality traits is of prime interest, for the possibility of improving the traits by marker-assisted selection (MAS) schemes. Therefore, the aim of this thesis was to investigate seven candidate genes for meat and carcass quality traits in pigs. In particular, we focused on genes belonging to the family of the lipid droplet coat proteins perilipins (PLIN1 and PLIN2) and to the calpain/calpastatin system (CAST, CAPN1, CAPN3, CAPNS1) and on the gene encoding for PPARg-coactivator 1A (PPARGC1A). In general, the candidate genes investigation included the protein localization, the detection of polymorphisms, the association analysis with meat and carcass traits and the analysis of the expression level, in order to assess the involvement of the gene in pork quality. Some of the analyzed genes showed effects on various pork traits that are subject to selection in genetic improvement programs, suggesting a possible involvement of the genes in controlling the traits variability. In particular, significant association results have been obtained for PLIN2, CAST and PPARGC1A genes, that are worthwhile of further validation. The obtained results contribute to a better understanding of biological mechanisms important for pig production as well as for a possible use of pig as animal model for studies regarding obesity in humans.

Functional polymer coatings — My-Patterning and My-Analysis

In dieser Arbeit werden Strukturen beschrieben, die mit Polymeren auf Oberflächen erzeugt wurden. Die Anwendungen reichen von PMMA und PNIPAM Polymerbürsten, über die Restrukturierung von Polystyrol durch Lösemittel bis zu 3D-Strukturen, die aus PAH/ PSS Polyelektrolytmultischichten bestehen. Im ersten Teil werden Polymethylmethacrylat (PMMA) Bürsten in der ionischen Flüssigkeit 1-Butyl-3-Methylimidazolium Hexafluorophospat ([Bmim][PF6]) durch kontrollierte radikalische Polymerisation (ATRP) hergestellt. Kinetische Untersuchungen zeigten ein lineares und dichtes Bürstenwachstum mit einer Wachstumsrate von 4600 g/mol pro nm. Die durchschnittliche Pfropfdichte betrug 0.36 µmol/m2. Als Anwendung wurden Mikrotropfen bestehend aus der ionischen Flüssigkeit, Dimethylformamid und dem ATRP-Katalysator benutzt, um in einer definierten Geometrie Polymerbürsten auf Silizium aufzubringen. Auf diese Weise lässt sich eine bis zu 13 nm dicke Beschichtung erzeugen. Dieses Konzept ist durch die Verdampfung des Monomers Methylmethacrylat (MMA) limitiert. Aus einem 1 µl großen Tropfen aus ionischer Flüssigkeit und MMA (1:1) verdampft MMA innerhalb von 100 s. Daher wurde das Monomer sequentiell zugegeben. Der zweite Teil konzentriert sich auf die Strukturierung von Oberflächen mit Hilfe einer neuen Methode: Tintendruck. Ein piezoelektrisch betriebenes „Drop-on-Demand“ Drucksystem wurde verwendet, um Polystyrol mit 0,4 nl Tropfen aus Toluol zu strukturieren. Die auf diese Art und Weise gebildeten Mikrokrater können Anwendung als Mikrolinsen finden. Die Brennweite der Mikrolinsen kann über die Anzahl an Tropfen, die für die Strukturierung verwendet werden, eingestellt werden. Theoretisch und experimentell wurde die Brennweite im Bereich von 4,5 mm bis 0,21 mm ermittelt. Der zweite Strukturierungsprozess nutzt die Polyelektrolyte Polyvinylamin-Hydrochlorid (PAH) und Polystyrolsulfonat (PSS), um 3D-Strukturen wie z.B. Linien, Schachbretter, Ringe, Stapel mit einer Schicht für Schicht Methode herzustellen. Die Schichtdicke für eine Doppelschicht (DS) liegt im Bereich von 0.6 bis 1.1 nm, wenn NaCl als Elektrolyt mit einer Konzentration von 0,5 mol/l eingesetzt wird. Die Breite der Strukturen beträgt im Mittel 230 µm. Der Prozess wurde erweitert, um Nanomechanische Cantilever Sensoren (NCS) zu beschichten. Auf einem Array bestehend aus acht Cantilevern wurden je zwei Cantilever mit fünf Doppelschichten PAH/ PSS und je zwei Cantilever mit zehn Doppelschichten PAH/ PSS schnell und reproduzierbar beschichtet. Die Massenänderung für die individuellen Cantilever war 0,55 ng für fünf Doppelschichten und 1,08 ng für zehn Doppelschichten. Der daraus resultierende Sensor wurde einer Umgebung mit definierter Luftfeuchtigkeit ausgesetzt. Die Cantilever verbiegen sich durch die Ausdehnung der Beschichtung, da Wasser in das Polymer diffundiert. Eine maximale Verbiegung von 442 nm bei 80% Luftfeuchtigkeit wurde für die mit zehn Doppelschichten beschichteten Cantilever gefunden. Dies entspricht einer Wasseraufnahme von 35%. Zusätzlich konnte aus den Verbiegungsdaten geschlossen werden, dass die Elastizität der Polyelektrolytmultischichten zunimmt, wenn das Polymer gequollen ist. Das thermische Verhalten in Wasser wurde im nächsten Teil an nanomechanischen Cantilever Sensoren, die mit Poly(N-isopropylacrylamid)bürsten (PNIPAM) und plasmapolymerisiertem N,N-Diethylacrylamid beschichtet waren, untersucht. Die Verbiegung des Cantilevers zeigte zwei Bereiche: Bei Temperaturen kleiner der niedrigsten kritischen Temperatur (LCST) ist die Verbiegung durch die Dehydration der Polymerschicht dominiert und bei Temperaturen größer der niedrigsten kritischen Temperatur (LCST) reagiert der Cantilever Sensor überwiegend auf Relaxationsprozesse innerhalb der kollabierten Polymerschicht. Es wurde gefunden, dass das Minimum in der differentiellen Verbiegung mit der niedrigsten kritischen Temperatur von 32°C und 44°C der ausgewählten Polymeren übereinstimmt. Im letzten Teil der Arbeit wurden µ-Reflektivitäts- und µ-GISAXS Experimente eingeführt als neue Methoden, um mikrostrukturierte Proben wie NCS oder PEM Linien mit Röntgenstreuung zu untersuchen. Die Dicke von jedem individuell mit PMMA Bürsten beschichtetem NCS ist im Bereich von 32,9 bis 35,2 nm, was mit Hilfe von µ-Reflektivitätsmessungen bestimmt wurde. Dieses Ergebnis kann mit abbildender Ellipsometrie als komplementäre Methode mit einer maximalen Abweichung von 7% bestätigt werden. Als zweites Beispiel wurde eine gedruckte Polyelektrolytmultischicht aus PAH/PSS untersucht. Die Herstellungsprozedur wurde so modifiziert, dass Goldnanopartikel in die Schichtstruktur eingebracht wurden. Durch Auswertung eines µ-GISAXS Experiments konnte der Einbau der Partikel identifiziert werden. Durch eine Anpassung mit einem Unified Fit Modell wurde herausgefunden, dass die Partikel nicht agglomeriert sind und von einer Polymermatrix umgeben sind.

Core-shell particles and their application for superhydrophobic surfaces

During the last years great effort has been devoted to the fabrication of superhydrophobic surfaces because of their self-cleaning properties. A water drop on a superhydrophobic surface rolls off even at inclinations of only a few degrees while taking up contaminants encountered on its way. rnSuperhydrophobic, self-cleaning coatings are desirable for convenient and cost-effective maintenance of a variety of surfaces. Ideally, such coatings should be easy to make and apply, mechanically resistant, and long-term stable. None of the existing methods have yet mastered the challenge of meeting all of these criteria.rnSuperhydrophobicity is associated with surface roughness. The lotus leave, with its dual scale roughness, is one of the most efficient examples of superhydrophobic surface. This thesis work proposes a novel technique to prepare superhydrophobic surfaces that introduces the two length scale roughness by growing silica particles (~100 nm in diameter) onto micrometer-sized polystyrene particles using the well-established Stöber synthesis. Mechanical resistance is conferred to the resulting “raspberries” by the synthesis of a thin silica shell on their surface. Besides of being easy to make and handle, these particles offer the possibility for improving suitability or technical applications: since they disperse in water, multi-layers can be prepared on substrates by simple drop casting even on surfaces with grooves and slots. The solution of the main problem – stabilizing the multilayer – also lies in the design of the particles: the shells – although mechanically stable – are porous enough to allow for leakage of polystyrene from the core. Under tetrahydrofuran vapor polystyrene bridges form between the particles that render the multilayer-film stable. rnMulti-layers are good candidate to design surfaces whose roughness is preserved after scratch. If the top-most layer is removed, the roughness can still be ensured by the underlying layer.rnAfter hydrophobization by chemical vapor deposition (CVD) of a semi-fluorinated silane, the surfaces are superhydrophobic with a tilting angle of a few degrees. rnrnrn

Seismic sequences analysis for estimation of earthquake source parameters: corner frequency, stress drop, and seismic moment observations

The present study has been carried out with the following objectives: i) To investigate the attributes of source parameters of local and regional earthquakes; ii) To estimate, as accurately as possible, M0, fc, Δσ and their standard errors to infer their relationship with source size; iii) To quantify high-frequency earthquake ground motion and to study the source scaling. This work is based on observational data of micro, small and moderate -earthquakes for three selected seismic sequences, namely Parkfield (CA, USA), Maule (Chile) and Ferrara (Italy). For the Parkfield seismic sequence (CA), a data set of 757 (42 clusters) repeating micro-earthquakes (0 ≤ MW ≤ 2), collected using borehole High Resolution Seismic Network (HRSN), have been analyzed and interpreted. We used the coda methodology to compute spectral ratios to obtain accurate values of fc , Δσ, and M0 for three target clusters (San Francisco, Los Angeles, and Hawaii) of our data. We also performed a general regression on peak ground velocities to obtain reliable seismic spectra of all earthquakes. For the Maule seismic sequence, a data set of 172 aftershocks of the 2010 MW 8.8 earthquake (3.7 ≤ MW ≤ 6.2), recorded by more than 100 temporary broadband stations, have been analyzed and interpreted to quantify high-frequency earthquake ground motion in this subduction zone. We completely calibrated the excitation and attenuation of the ground motion in Central Chile. For the Ferrara sequence, we calculated moment tensor solutions for 20 events from MW 5.63 (the largest main event occurred on May 20 2012), down to MW 3.2 by a 1-D velocity model for the crust beneath the Pianura Padana, using all the geophysical and geological information available for the area. The PADANIA model allowed a numerical study on the characteristics of the ground motion in the thick sediments of the flood plain.

Mineral dust mobilisation, transport, and deposition in different climate epochs

Mineral dust is an important component of the Earth's climate system and provides essential nutrientsrnto oceans and rain forests. During atmospheric transport, dust particles directly and indirectly influencernweather and climate. The strength of dust sources and characteristics of the transport, in turn, mightrnbe subject to climatic changes. Earth system models help for a better understanding of these complexrnmechanisms.rnrnThis thesis applies the global climate model ECHAM5/MESSy Atmospheric Chemistry (EMAC) for simulationsrnof the mineral dust cycle under different climatic conditions. The prerequisite for suitable modelrnresults is the determination of the model setup reproducing the most realistic dust cycle in the recentrnclimate. Simulations with this setup are used to gain new insights into properties of the transatlanticrndust transport from Africa to the Americas and adaptations of the model's climate forcing factors allowrnfor investigations of the impact of climatic changes on the dust cycle.rnrnIn the first part, the most appropriate model setup is determined through a number of sensitivity experiments.rnIt uses the dust emission parametrisation from Tegen et al. 2002 and a spectral resolutionrnof T85, corresponding to a horizontal grid spacing of about 155 km. Coarser resolutions are not able tornaccurately reproduce emissions from important source regions such as the Bodele Depression in Chad orrnthe Taklamakan Desert in Central Asia. Furthermore, the representation of ageing and wet deposition ofrndust particles in the model requires a basic sulphur chemical mechanism. This setup is recommended forrnfuture simulations with EMAC focusing on mineral dust.rnrnOne major branch of the global dust cycle is the long-range transport from the world's largest dustrnsource, the Sahara, across the Atlantic Ocean. Seasonal variations of the main transport pathways to thernAmazon Basin in boreal winter and to the Caribbean during summer are well known and understood,rnand corroborated in this thesis. Both Eulerian and Lagrangian methods give estimates on the typicalrntransport times from the source regions to the deposition on the order of nine to ten days. Previously, arnhuge proportion of the dust transported across the Atlantic Ocean has been attributed to emissions fromrnthe Bodele Depression. However, the contribution of this hot spot to the total transport is very low inrnthe present results, although the overall emissions from this region are comparable. Both model resultsrnand data sets analysed earlier, such as satellite products, involve uncertainties and this controversy aboutrndust transport from the Bodele Depression calls for future investigations and clarification.rnrnAforementioned characteristics of the transatlantic dust transport just slightly change in simulationsrnrepresenting climatic conditions of the Little Ice Age in the middle of the last millennium with meanrnnear-surface cooling of 0.5 to 1 K. However, intensification of the West African summer monsoon duringrnthe Little Ice Age is associated with higher dust emissions from North African source regions and wetterrnconditions in the Sahel. Furthermore, the Indian Monsoon and dust emissions from the Arabian Peninsula,rnwhich are affected by this circulation, are intensified during the Little Ice Age, whereas the annual globalrndust budget is similar in both climate epochs. Simulated dust emission fluxes are particularly influencedrnby the surface parameters. Modifications of the model do not affect those in this thesis, to be able tornascribe all differences in the results to changed forcing factors, such as greenhouse gas concentrations.rnDue to meagre comparison data sets, the verification of results presented here is problematic. Deeperrnknowledge about the dust cycle during the Little Ice Age can be obtained by future simulations, based onrnthis work, and additionally using improved reconstructions of surface parameters. Better evaluation ofrnsuch simulations would be possible by refining the temporal resolution of reconstructed dust depositionrnfluxes from existing ice and marine sediment cores.

Global modeling of pollutant transport and deposition from anthropogenic emission hot spots on global scale

Urban centers significantly contribute to anthropogenic air pollution, although they cover only a minor fraction of the Earth's land surface. Since the worldwide degree of urbanization is steadily increasing, the anthropogenic contribution to air pollution from urban centers is expected to become more substantial in future air quality assessments. The main objective of this thesis was to obtain a more profound insight in the dispersion and the deposition of aerosol particles from 46 individual major population centers (MPCs) as well as the regional and global influence on the atmospheric distribution of several aerosol types. For the first time, this was assessed in one model framework, for which the global model EMAC was applied with different representations of aerosol particles. First, in an approach with passive tracers and a setup in which the results depend only on the source location and the size and the solubility of the tracers, several metrics and a regional climate classification were used to quantify the major outflow pathways, both vertically and horizontally, and to compare the balance between pollution export away from and pollution build-up around the source points. Then in a more comprehensive approach, the anthropogenic emissions of key trace species were changed at the MPC locations to determine the cumulative impact of the MPC emissions on the atmospheric aerosol burdens of black carbon, particulate organic matter, sulfate, and nitrate. Ten different mono-modal passive aerosol tracers were continuously released at the same constant rate at each emission point. The results clearly showed that on average about five times more mass is advected quasi-horizontally at low levels than exported into the upper troposphere. The strength of the low-level export is mainly determined by the location of the source, while the vertical transport is mainly governed by the lifting potential and the solubility of the tracers. Similar to insoluble gas phase tracers, the low-level export of aerosol tracers is strongest at middle and high latitudes, while the regions of strongest vertical export differ between aerosol (temperate winter dry) and gas phase (tropics) tracers. The emitted mass fraction that is kept around MPCs is largest in regions where aerosol tracers have short lifetimes; this mass is also critical for assessing the impact on humans. However, the number of people who live in a strongly polluted region around urban centers depends more on the population density than on the size of the area which is affected by strong air pollution. Another major result was that fine aerosol particles (diameters smaller than 2.5 micrometer) from MPCs undergo substantial long-range transport, with about half of the emitted mass being deposited beyond 1000 km away from the source. In contrast to this diluted remote deposition, there are areas around the MPCs which experience high deposition rates, especially in regions which are frequently affected by heavy precipitation or are situated in poorly ventilated locations. Moreover, most MPC aerosol emissions are removed over land surfaces. In particular, forests experience more deposition from MPC pollutants than other land ecosystems. In addition, it was found that the generic treatment of aerosols has no substantial influence on the major conclusions drawn in this thesis. Moreover, in the more comprehensive approach, it was found that emissions of black carbon, particulate organic matter, sulfur dioxide, and nitrogen oxides from MPCs influence the atmospheric burden of various aerosol types very differently, with impacts generally being larger for secondary species, sulfate and nitrate, than for primary species, black carbon and particulate organic matter. While the changes in the burdens of sulfate, black carbon, and particulate organic matter show an almost linear response for changes in the emission strength, the formation of nitrate was found to be contingent upon many more factors, e.g., the abundance of sulfuric acid, than only upon the strength of the nitrogen oxide emissions. The generic tracer experiments were further extended to conduct the first risk assessment to obtain the cumulative risk of contamination from multiple nuclear reactor accidents on the global scale. For this, many factors had to be taken into account: the probability of major accidents, the cumulative deposition field of the radionuclide cesium-137, and a threshold value that defines contamination. By collecting the necessary data and after accounting for uncertainties, it was found that the risk is highest in western Europe, the eastern US, and in Japan, where on average contamination by major accidents is expected about every 50 years.