H-induced platelet and crack formation in hydrogenated epitaxial Si/Si0.98 B0.02 /Si structures

An approach to transfer a high-quality Si layer for the fabrication of silicon-on-insulator wafers has been proposed based on the investigation of platelet and crack formation in hydrogenated epitaxialSi/Si0.98B0.02/Si structures grown by molecular-beam epitaxy. H-related defect formation during hydrogenation was found to be very sensitive to the thickness of the buried Si0.98B0.02 layer. For hydrogenated Si containing a 130nm thick Si0.98B0.02 layer, no platelets or cracking were observed in the B-doped region. Upon reducing the thickness of the buried Si0.98B0.02 layer to 3nm, localized continuous cracking was observed along the interface between the Si and the B-doped layers. In the latter case, the strains at the interface are believed to facilitate the (100)-oriented platelet formation and (100)-oriented crack propagation.

Synthesis and characterization of some Mn(II) and Mn(III) complexes of N,N′-o-phenylenebis(salicylideneimine)(LH2) and N,N′-o-phenylenebis(5-bromosalicylideneimine)(L′H2). Crystal structures of [Mn(L)(H2O)(ClO4)], [Mn(L)(NCS)] and an infinite linear chain of [Mn(L)(OAc)]

A series of manganese(II) [Mn(L)] and manganese(III) [Mn(L)(X)] (X = ClO4, OAc, NCS, N3, Cl, Br and I) complexes have been synthesized from Schiff base ligands N,N′-o- phenylenebis(salicylideneimine)(LH2) and N,N′-o-phenylenebis(5- bromosalicylideneimine)(L′H2) obtained by condensation of salicylaldehyde or 5-Br salicylaldehyde with o-phenylene-diamine. The complexes have been characterized by the combination of IR, UV-Vis spectroscopy, magnetic measurements and electrochemical studies. Three manganese(III) complexes 3 [Mn(L)(ClO4)(H2O)], 5 [Mn(L)(OAc)] and 13 [Mn(L)(NCS)] have been characterized by X-ray crystallography. The X-ray structures show that the manganese(III) is hexa-coordinated in 3, it is penta-coordinated in 13, while in 5 there is an infinite chain where the MnL moieties are connected by acetate ions acting as bridging bidentate ligand. The cyclic voltammograms of all the manganese(III) complexes exhibit two reversible/quasi-reversible/ irreversible responses assignable to Mn(III)/Mn(II) and Mn(IV)/Mn(III) couples. It was observed that the ligand L′H2 containing the 5-bromosal moiety always stabilizes the lower oxidation states compared to the corresponding unsubstituted LH2. Cyclic voltammograms of the manganese(II) complexes (1 and 2) exhibit a quasi-reversible Mn(III)/Mn(II) couple at E1/2 -0.08 V for 1 and 0.054 V for 2. © 2005 Elsevier B.V. All rights reserved.

Studies on the relative stabilities of Mn(II) and Mn(III) in complexes with N4O2 donor environments:crystal structures of [Mn(pybzhz)2] and [Mn(Ophsal)(imzH)2] ClO4 (pybzhz = N-(benzoyl)-N-(picolinylidene) hydrazine, Ophsal = N,N-o-phenylenebis(salicylideneimine), imzH = imidazole)

Five manganese complexes in an N 4O 2 donor environment have been prepared. Four of the compounds involve aroyl hydrazone as ligands and manganese is in a +2 oxidation state. The fifth compound was prepared using N,Nprime-o-phenylenebis(salicylideneimine) and imidazole as ligands where manganese is present in +3 oxidation state. X-ray crystal structure of one Mn +2 compound and the Mn +3 compound was determined. The relative stabilities of the Mn +2 and Mn +3 oxidation states were analyzed using the structural data and MO calculations. Manganese(II) complexes of four aroyl hydrazone ligands were prepared and characterized by different physicochemical techniques. The complexes are of the type Mn(L) 2, where L stands for the deprotonated hydrazone ligand. One of the compounds, Mn(pybzhz) 2, was also characterized by single crystal structure determination. In all these complexes, the Mn(II) is in an N 4O 2 donor environment and the Mn(II) center cannot be oxidized either chemically or electrochemically. However, when another ligand Ophsal is used to give the compound [Mn(Ophsal)(imzH) 2]ClO 4, which was also characterized by X-ray crystal structure determination, manganese can easily avail the +3 oxidation state. The relative stabilities of the +2 and +3 oxidation states of manganese were analyzed and it was concluded that the extent of distortion from the perfect octahedral geometry is the main controlling factor in these cases. © 2004 Elsevier B.V. All rights reserved.

Analysis of functional materials by X-ray photoelectron spectroscopy

X-ray photoelectron spectroscopy (XPS) can play an important role in guiding the design of new materials, tailored to meet increasingly stringent constraints on performance devices, by providing insight into their surface compositions and the fundamental interactions between the surfaces and the environment. This chapter outlines the principles and application of XPS as a versatile, chemically specific analytical tool in determining the electronic structures and (usually surface) compositions of constituent elements within diverse functional materials. Advances in detector electronics have opened the way for development of photoelectron microscopes and instruments with XPS imaging capabilities. Advances in surface science instrumentation to enable time-resolved spectroscopic measurements offer exciting opportunities to quantitatively investigate the composition, structure and dynamics of working catalyst surfaces. Attempts to study the effects of material processing in realistic environments currently involves the use of high- or ambient-pressure XPS in which samples can be exposed to reactive environments.

X-ray crystallographic and theoretical studies of an anticonvulsant enaminone:methyl 4-(4'-bromophenyl)amino-6-methyl-2-oxocyclohex-3-en-1-oate

Objective: The aims of this study were to establish the structure of the potent anticonvulsant enaminone methyl 4-(4′-bromophenyl)amino-6-methyl-2- oxocyclohex-3-en-1-oate (E139), and to determine the energetically preferred conformation of the molecule, which is responsible for the biological activity. Materials and Methods: The structure of the molecule was determined by X-ray crystallography. Theoretical ab initio calculations with different basis sets were used to compare the energies of the different enantiomers and to other structurally related compounds. Results: The X-ray crystal structure revealed two independent molecules of E139, both with absolute configuration C11(S), C12(R), and their inverse. Ab initio calculations with the 6-31G, 3-21G and STO-3G basis sets confirmed that the C11(S), C12(R) enantiomer with both substituents equatorial had the lowest energy. Compared to relevant crystal structures, the geometry of the theoretical structures shows a longer C-N and shorter C=O distance with more cyclohexene ring puckering in the isolated molecule. Conclusion: Based on a pharmacophoric model it is suggested that the enaminone system HN-C=C-C=O and the 4-bromophenyl group in E139 are necessary to confer anticonvulsant property that could lead to the design of new and improved anticonvulsant agents. Copyright © 2003 S. Karger AG, Basel.

Arthur Lindo Patterson, his function and element preferences in early crystal structures

In 1934, Arthur Lindo Patterson showed that a map of interatomic vectors is obtainable from measured X-ray diffraction data without phase information. Such maps were interpretable for simple crystal structures, but proliferation and overlapping of peaks caused confusion as the number of atoms increased. Since the peak height of a vector between two particular atoms is related to the product of their atomic numbers, a complicated structure could effectively be reduced to a simple one by including just a few heavy atoms (of high atomic number) since their interatomic vectors would stand out from the general clutter. Once located, these atoms provide approximate phases for Fourier syntheses that reveal the locations of additional atoms. Surveys of small-molecule structures in the Cambridge Structural Database during the periods 1936-1969, when Patterson methods were commonly used, and 1980-2013, dominated by direct methods, demonstrate large differences in the abundance of certain elements. The moderately heavy elements K, Rb, As and Br are the heaviest elements in the structure more than 3 times as often in the early period than in the recent period. Examples are given of three triumphs of the heavy atom method and two initial failures that had to be overcome. © 2014 © 2014 Taylor & Francis.

On Affine Connections in a Riemannian Manifold with a Circulant Metric and two Circulant Affinor Structures

Ива Р. Докузова, Димитър Р. Разпопов - В настоящата статия е разгледан клас V оттримерни риманови многообразия M с метрика g и два афинорни тензора q и S. Дефинирана е и друга метрика ¯g в M. Локалните координати на всички тези тензори са циркулантни матрици. Намерени са: 1) зависимост между тензора на кривина R породен от g и тензора на кривина ¯R породен от ¯g; 2) тъждество за тензора на кривина R в случая, когато тензорът на кривина ¯R се анулира; 3) зависимост между секционната кривина на прозволна двумерна q-площадка {x, qx} и скаларната кривина на M.

Noise in gallium nitride-based quantum well structures used for nanometer devices in the frequency range 1 Hz--3 Mhz and temperature range 77K--324K

Electronic noise has been investigated in AlxGa1−x N/GaN Modulation-Doped Field Effect Transistors (MODFETs) of submicron dimensions, grown for us by MBE (Molecular Beam Epitaxy) techniques at Virginia Commonwealth University by Dr. H. Morkoç and coworkers. Some 20 devices were grown on a GaN substrate, four of which have leads bonded to source (S), drain (D), and gate (G) pads, respectively. Conduction takes place in the quasi-2D layer of the junction (xy plane) which is perpendicular to the quantum well (z-direction) of average triangular width ∼3 nm. A non-doped intrinsic buffer layer of ∼5 nm separates the Si-doped donors in the AlxGa1−xN layer from the 2D-transistor plane, which affords a very high electron mobility, thus enabling high-speed devices. Since all contacts (S, D, and G) must reach through the AlxGa1−xN layer to connect internally to the 2D plane, parallel conduction through this layer is a feature of all modulation-doped devices. While the shunting effect may account for no more than a few percent of the current IDS, it is responsible for most excess noise, over and above thermal noise of the device. ^ The excess noise has been analyzed as a sum of Lorentzian spectra and 1/f noise. The Lorentzian noise has been ascribed to trapping of the carriers in the AlxGa1−xN layer. A detailed, multitrapping generation-recombination noise theory is presented, which shows that an exponential relationship exists for the time constants obtained from the spectral components as a function of 1/kT. The trap depths have been obtained from Arrhenius plots of log (τT2) vs. 1000/T. Comparison with previous noise results for GaAs devices shows that: (a) many more trapping levels are present in these nitride-based devices; (b) the traps are deeper (farther below the conduction band) than for GaAs. Furthermore, the magnitude of the noise is strongly dependent on the level of depletion of the AlxGa1−xN donor layer, which can be altered by a negative or positive gate bias VGS. ^ Altogether, these frontier nitride-based devices are promising for bluish light optoelectronic devices and lasers; however, the noise, though well understood, indicates that the purity of the constituent layers should be greatly improved for future technological applications. ^

Implementation of X-ray diffraction in the measurement of residual thermal strains

Microelectronic systems are multi-material, multi-layer structures, fabricated and exposed to environmental stresses over a wide range of temperatures. Thermal and residual stresses created by thermal mismatches in films and interconnections are a major cause of failure in microelectronic devices. Due to new device materials, increasing die size and the introduction of new materials for enhanced thermal management, differences in thermal expansions of various packaging materials have become exceedingly important and can no longer be neglected. X-ray diffraction is an analytical method using a monochromatic characteristic X-ray beam to characterize the crystal structure of various materials, by measuring the distances between planes in atomic crystalline lattice structures. As a material is strained, this interplanar spacing is correspondingly altered, and this microscopic strain is used to determine the macroscopic strain. This thesis investigates and describes the theory and implementation of X-ray diffraction in the measurement of residual thermal strains. The design of a computer controlled stress attachment stage fully compatible with an Anton Paar heat stage will be detailed. The stress determined by the diffraction method will be compared with bimetallic strip theory and finite element models.

Semi-engineered earthquake-resistant structures: one-storey buildings built up with gabion-box walls

This thesis studies the static and seismic behavior of simple structures made with gabion box walls. The analysis was performed considering a one-story building with standard dimensions in plan (6m x 5m) and a lightweight timber roof. The main focus of the present investigation is to find the principals aspects of the seismic behavior of a one story building made with gabion box walls, in order to prevent a failure due to seismic actions and in this way help to reduce the seismic risk of developing countries where this natural disaster have a significant intensity. Regarding the gabion box wall, it has been performed some calculations and analysis in order to understand the static and dynamic behavior. From the static point of view, it has been performed a verification of the normal stress computing the normal stress that arrives at the base of the gabion wall and the corresponding capacity of the ground. Moreover, regarding the seismic analysis, it has been studied the in-plane and out-of-plane behavior. The most critical aspect was discovered to be the out-of-plane behavior, for which have been developed models considering the “rigid- no tension model” for masonry, finding a kinematically admissible multiplier that will create a collapse mechanism for the structure. Furthermore, it has been performed a FEM and DEM models to find the maximum displacement at the center of the wall, maximum tension stresses needed for calculating the steel connectors for joining consecutive gabions and the dimensions (length of the wall and distance between orthogonal walls or buttresses) of a geometrical configuration for the standard modulus of the structure, in order to ensure an adequate safety margin for earthquakes with a PGA around 0.4-0.5g. Using the results obtained before, it has been created some rules of thumb, that have to be satisfy in order to ensure a good behavior of these structure.

Sediment rates and structures in Bay of Kiel, Baltic Sea

Density and diversity of bottom fauna population as dependent on sediment types and water depth is largely well known in Kiel Bay. This is in contrast to structures and processes of bioturbation, although generally it has a big influence on the benthic boundary layer and its processes, e.g., the metabolism of the bottom fauna, the mechanical properties, the age dating, and the large field of chemical processes. In the densely inhabited sands and muddy sands of the shallower waters with sediment thicknesses of some decimeters only, bioturbation is usually ubiquitous, and most of the structures left are monotonously of "biodeformational" character. At greater water depths, however, where a sedimentary column of several meters of Holocene is developed, the X-ray radiographs of numerous sediment cores show heterogeneous biogenic structures with regional and stratigraphical differentiation. They are described in terms of ichnofabrics and are interpreted on ethological knowledge of the related macrobenthos species. lmportant organisms creating specific traces include the bivalve Arctica (Cyprina) islandica and the polychaete worm Pectinaria koreni. These species are abundant in Kiel Bay and produce by their crawling-plowing mode of locomotion, a characteristic biogenic stratification, the "plow-sole structure". Other typical biogenic structures are tube traces, which are left by a number of different polychaetes occurring either singly, or as U-pairs mainly in mud sediments. Although sea urchins are rare to absent in Kiel Bay, layers of their characteristic traces Scolicia occur as witness of paleohydrographic events in channel sediments of the central bay. Plow-sole traces, polychaete-tube ichnofabric, Scolicia layers and alternations of laminated and bioturbated layers are considered as building blocks of a future "ichnostratigraphy" of Kiel Bay.

Gravity collapse structures in the Central Precordillera fold-andthrust belt, Argentina

Several landforms found in the fold-and-thrust belt area of Central Precordillera, Pre-Andes of Argentina, which were often associated with tectonic efforts, are in fact related to non-tectonic processes or gravitational superficial structures. These second-order structures, interpreted as gravitational collapse structures, have developed in the western flank of sierras de La Dehesa and Talacasto. These include rock-slides, rock falls, wrinkle folds, slip sheets and flaps, among others; which together constitute a monoclinal fold dipping between 30º and 60º to the west. Gravity collapse structures are parallel to the regional strike of the Sierra de la Dehesa and are placed in Ordovician limestones and dolomites. Their sloping towards the west, the presence of bed planes, fractures and joints; and the lithology (limestone interbedded with incompetent argillaceous banks) would have favored their occurrence. Movement of the detached structures has been controlled by lithology characteristics, as well as by bedding and joints. Detachment and initial transport of gravity collapse structures and rockslides in the western flank of the Sierra de la Dehesa were tightly controlled by three structural elements: 1) sliding surfaces developed on parallel bedded strata when dipping >30° in the slope direction; 2) Joint’s sets constitute lateral and transverse traction cracks which release extensional stresses and 3) Discontinuities fragmenting sliding surfaces.  Some other factors that could be characterized as local (lithology, structure and topography) and as regional (high seismic activity and possibly wetter conditions during the postglacial period) were determining in favoring the steady loss of the western mountain side in the easternmost foothills of Central Precordillera.

Transition metal complexes of some N4-phenylsemicarbazones: crystal structures and spectral studies

The work embodied in this thesis was carried out by the author in the Department of Applied Chemistry, CUSAT, Kochi, during the period 2009-2012. The thesis is an introduction to our attempts to evaluate the coordination behavior of some compounds of our interest. The biological activities of semicarbazones and their metal complexes have been an active area of research during the past years because of their significant role in naturally occurring biological systems. Tridentate NNO and ONO semicarbazone systems formed from heterocyclic and aromatic carbonyl compounds and their transition metal complexes are wellauthenticated compounds in this field and their synthesis, crystal structures and spectral studies are well desirable. Hence, we decided to develop a research program aimed at the syntheses, crystal structures and spectral studies of new N4- phenylsemicarbazones derived from 2-formylpyridine and 3-ethoxysalicylaldehyde and their transition metal complexes and new transition metal complexes of 2- benzoylpyridine-N4-phenylsemicarbazone. In addition to various physicochemical methods of analysis, single crystal X-ray diffraction studies were also used for the characterization of the complexes.

Insight into Biological Small-Molecule Activation from Enzymes, Model Complexes, and X-ray Spectroscopy

Thesis (Ph.D.)--University of Washington, 2016-08