Analysis of an internally mountable accelerometer balance system for use with non-isotropic models in shock tunnels

Knowledge of drag force is an important design parameter in aerodynamics. Measurement of aerodynamic forces at hypersonic speed is a challenge and usually ground test facilities like shock tunnels are used to carry out such tests. Accelerometer based force balances are commonly employed for measuring aerodynamic drag around bodies in hypersonic shock tunnels. In this study, we present an analysis of the effect of model material on the performance of an accelerometer balance used for measurement of drag in impulse facilities. From the experimental studies performed on models constructed out of Bakelite HYLEM and Aluminum, it is clear that the rigid body assumption does not hold good during the short testing duration available in shock tunnels. This is notwithstanding the fact that the rubber bush used for supporting the model allows unconstrained motion of the model during the short testing time available in the shock tunnel. The vibrations induced in the model on impact loading in the shock tunnel are damped out in metallic model, resulting in a smooth acceleration signal, while the signal become noisy and non-linear when we use non-isotropic materials like Bakelite HYLEM. This also implies that careful analysis and proper data reduction methodologies are necessary for measuring aerodynamic drag for non-metallic models in shock tunnels. The results from the drag measurements carried out using a 60 degrees half angle blunt cone is given in the present analysis.

A note on acyclic edge coloring of complete bipartite graphs

An acyclic edge coloring of a graph is a proper edge coloring such that there are no bichromatic (2-colored) cycles. The acyclic chromatic index of a graph is the minimum number k such that there is an acyclic edge coloring using k colors and is denoted by a'(G). Let Delta = Delta(G) denote the maximum degree of a vertex in a graph G. A complete bipartite graph with n vertices on each side is denoted by K-n,K-n. Alon, McDiarmid and Reed observed that a'(K-p-1,K-p-1) = p for every prime p. In this paper we prove that a'(K-p,K-p) <= p + 2 = Delta + 2 when p is prime. Basavaraju, Chandran and Kummini proved that a'(K-n,K-n) >= n + 2 = Delta + 2 when n is odd, which combined with our result implies that a'(K-p,K-p) = p + 2 = Delta + 2 when p is an odd prime. Moreover we show that if we remove any edge from K-p,K-p, the resulting graph is acyclically Delta + 1 = p + 1-edge-colorable. (C) 2009 Elsevier B.V. All rights reserved.

Signal Characterization using Fractal Dimension

Fractal Dimensions (FD) are popular metrics for characterizing signals. They are used as complexity measuresin signal analysis applications in various fields. However, proper interpretation of such analyses has not been thoroughly addressed. In this paper, we study the effect of various signal properties on FD and interpret results in terms of classical signal processing concepts such as amplitude, frequency,number of harmonics, noise power and signal bandwidth. We have used Higuchi’s method for estimating FDs. This study helps in gaining a better understanding of the FD complexity measure for various signal parameters. Our results indicate that FD is a useful metric in estimating various signal properties. As an application of the FD measure in real world scenario, the FD is used as a feature in discriminating seizures from seizure free intervals in intracranial EEG data recordings and the FD feature has given good discrimination performance.

Soveltuvuuskokeella täydennetty opiskelijavalinta : Seurantatutkimus eräiden sosiaali- ja terveysalan teknisluonteisten koulutusohjelmien (apuvälinetekniikka, hammastekniikka ja optometria) opiskelijavalinnan toteuttamisesta

Aptitude-based student selection: A study concerning the admission processes of some technically oriented healthcare degree programmes in Finland (Orthotics and Prosthetics, Dental Technology and Optometry). The data studied consisted of conveniencesamples of preadmission information and the results of the admission processes of three technically oriented healthcare degree programmes (Orthotics and Prosthetics, Dental Technology and Optometry) in Finland during the years 1977-1986 and 2003. The number of the subjects tested and interviewed in the first samples was 191, 615 and 606, and in the second 67, 64 and 89, respectively. The questions of the six studies were: I. How were different kinds of preadmission data related to each other? II. Which were the major determinants of the admission decisions? III. Did the graduated students and those who dropped out differ from each other? IV. Was it possible to predict how well students would perform in the programmes? V. How was the student selection executed in the year 2003? VI. Should clinical vs. statistical prediction or both be used? (Some remarks are presented on Meehl's argument: "Always, we might as well face it, the shadow of the statistician hovers in the background; always the actuary will have the final word.") The main results of the study were as follows: Ability tests, dexterity tests and judgements of personality traits (communication skills, initiative, stress tolerance and motivation) provided unique, non-redundant information about the applicants. Available demographic variables did not bias the judgements of personality traits. In all three programme settings, four-factor solutions (personality, reasoning, gender-technical and age-vocational with factor scores) could be extracted by the Maximum Likelihood method with graphical Varimax rotation. The personality factor dominated the final aptitude judgements and very strongly affected the selection decisions. There were no clear differences between graduated students and those who had dropped out in regard to the four factors. In addition, the factor scores did not predict how well the students performed in the programmes. Meehl's argument on the uncertainty of clinical prediction was supported by the results, which on the other hand did not provide any relevant data for rules on statistical prediction. No clear arguments for or against the aptitude-based student selection was presented. However, the structure of the aptitude measures and their impact on the admission process are now better known. The concept of "personal aptitude" is not necessarily included in the values and preferences of those in charge of organizing the schooling. Thus, obviously the most well-founded and cost-effective way to execute student selection is to rely on e.g. the grade point averages of the matriculation examination and/or written entrance exams. This procedure, according to the present study, would result in a student group which has a quite different makeup (60%) from the group selected on the basis of aptitude tests. For the recruiting organizations, instead, "personal aptitude" may be a matter of great importance. The employers, of course, decide on personnel selection. The psychologists, if consulted, are responsible for the proper use of psychological measures.

Reassessing the earthquake hazard in Kerala based on the historical and current seismicity

Given the lack of proper constraints in understanding earthquake mechanisms in the cratonic interiors and the general absence of good quality database, here we reassess the seismic hazard in the province of Kerala, a part of the aEuro cent stable continental interioraEuro cent, based on an improved historical and instrumental database. The temporal pattern of the current seismicity suggests that > 60% of the microtremors in Kerala occurs with a time lag after the peak rainfall, indicating that hydroseismicity may be a plausible model to explain the low-level seismicity in this region. Further, an increment in overall seismicity rate in the region in the recent years is explained as due to increased anthropogenic activities, which includes changes in hydrological pathways as a consequence of rapid landscape changes. Our analyses of the historical database eliminate a few events that are ascribed to this region; this exercise has also led to identification of a few events, not previously noted. The improved historical database essentially suggests that the central midland region is more prone to seismic activity compared to other parts of Kerala. This region appears to have generated larger number of significant earthquakes; the most prominent being the multiple events (doublets) of 1856 and 1953, whose magnitudes are comparable to that of the 2000/2001 (central Kerala) events. Occurrences of these historical events and the recent earthquakes, and the local geology indicative of pervasive faulting as shown by widely distributed pseudotachylite veins suggest that the NNW-SSE trending faults in central midland Kerala may host discrete potentially active sources that may be capable of generating light to moderate size earthquakes. The frequency of earthquakes in central Kerala evident from the historical database requires that the seismic codes stipulated for this region are made mandatory.

Acyclic Edge Coloring of Graphs with Maximum Degree 4

An acyclic edge coloring of a graph is a proper edge coloring such that there are no bichromatic cycles. The acyclic chromatic index of a graph is the minimum number k such that there is an acyclic edge coloring using k colors and is denoted by a'(G). It was conjectured by Alon, Sudakov, and Zaks that for any simple and finite graph G, a'(G) <= Delta+2, where Delta=Delta(G) denotes the maximum degree of G. We prove the conjecture for connected graphs with Delta(G)<= 4, with the additional restriction that m <= 2n-1, where n is the number of vertices and m is the number of edges in G. Note that for any graph G, m <= 2n, when Delta(G)<= 4. It follows that for any graph G if Delta(G)<= 4, then a'(G) <= 7.

Evaluation of driving ability of the disabled persons in the context of the psychological activity theory

In the future the number of the disabled drivers requiring a special evaluation of their driving ability will increase due to the ageing population, as well as the progress of adaptive technology. This places pressure on the development of the driving evaluation system. Despite quite intensive research there is still no consensus concerning what is the factual situation in a driver evaluation (methodology), which measures should be included in an evaluation (methods), and how an evaluation has to be carried out (practise). In order to find answers to these questions we carried out empirical studies, and simultaneously elaborated upon a conceptual model for driving and a driving evaluation. The findings of empirical studies can be condensed into the following points: 1) A driving ability defined by the on-road driving test is associated with different laboratory measures depending on the study groups. Faults in the laboratory tests predicted faults in the on-road driving test in the novice group, whereas slowness in the laboratory predicted driving faults in the experienced drivers group. 2) The Parkinson study clearly showed that even an experienced clinician cannot reliably accomplish an evaluation of a disabled person’s driving ability without collaboration with other specialists. 3) The main finding of the stroke study was that the use of a multidisciplinary team as a source of information harmonises the specialists’ evaluations. 4) The patient studies demonstrated that the disabled persons themselves, as well as their spouses, are as a rule not reliable evaluators. 5) From the safety point of view, perceptible operations with the control devices are not crucial, but correct mental actions which the driver carries out with the help of the control devices are of greatest importance. 6) Personality factors including higher-order needs and motives, attitudes and a degree of self-awareness, particularly a sense of illness, are decisive when evaluating a disabled person’s driving ability. Personality is also the main source of resources concerning compensations for lower-order physical deficiencies and restrictions. From work with the conceptual model we drew the following methodological conclusions: First, the driver has to be considered as a holistic subject of the activity, as a multilevel hierarchically organised system of an organism, a temperament, an individuality, and a personality where the personality is the leading subsystem from the standpoint of safety. Second, driving as a human form of a sociopractical activity, is also a hierarchically organised dynamic system. Third, in an evaluation of driving ability it is a question of matching these two hierarchically organised structures: a subject of an activity and a proper activity. Fourth, an evaluation has to be person centred but not disease-, function- or method centred. On the basis of our study a multidisciplinary team (practitioner, driving school teacher, psychologist, occupational therapist) is recommended for use in demanding driver evaluations. Primary in a driver’s evaluations is a coherent conceptual model while concrete methods of evaluations may vary. However, the on-road test must always be performed if possible.

Lawyers linked to litigation funding face court censure: Bolitho v Banksia Securities Limited (No.4) [2014] VSC 582

In Bolitho v Banksia Securities Limited (No 4) [2014] VSC 582 the Supreme Court of Victoria concluded that the proper administration of justice, including the appearance of justice, required that the lawyers representing the plaintiff in the group proceeding should be restrained from continuing to act for the plaintiff. This Victorian case illustrates how courts are likely to respond when lawyers attempt to circumvent the prohibition on contingency fees through litigation funding in which they have a financial interest.

Datorstödda studier i hälso- och socialvård : MuPSiNet-projektet

The aim of the study was to explore why the MuPSiNet project - a computer and network supported learning environment for the field of health care and social work - did not develop as expected. To grasp the problem some hypotheses were formulated. The hypotheses regarded the teachers' skills in and attitudes towards computing and their attitudes towards constructivist study methods. An online survey containing 48 items was performed. The survey targeted all the teachers within the field of health care and social work in the country, and it produced 461 responses that were analysed against the hypotheses. The reliability of the variables was tested using the Cronbach alpha coefficient and t-tests. Poor basic computing skills among the teachers combined with a vulnerable technical solution, and inadequate project management combined with lack of administrative models for transforming economic resources into manpower were the factors that turned out to play a decisive role in the project. Other important findings were that the teachers had rather poor skills and knowledge in computing, computer safety and computer supported instruction, and that these skills were significantly poorer among female teachers who were in majority in the sample. The fraction of teachers who were familiar with software for electronic patient records (EPR) was low. The attitudes towards constructivist teaching methods were positive, and further education seemed to utterly increase the teachers' readiness to use alternative teaching methods. The most important conclusions were the following: In order to integrate EPR software as a natural tool in teaching planning and documenting health care, it is crucial that the teachers have sufficient basic skills in computing and that more teachers have personal experience of using EPR software. In order for computer supported teaching to become accepted it is necessary to arrange with extensive further education for the teachers presently working, and for that further education to succeed it should be backed up locally among other things by sufficient support in matters concerning computer supported teaching. The attitudes towards computing showed significant gender differences. Based on the findings it is suggested that basic skills in computing should also include an awareness of data safety in relation to work in different kinds of computer networks, and that projects of this kind should be built up around a proper project organisation with sufficient resources. Suggestions concerning curricular development and further education are also presented. Conclusions concerning the research method were that reminders have a better effect, and that respondents tend to answer open-ended questions more verbosely in electronically distributed online surveys compared to traditional surveys. A method of utilising randomized passwords to guarantee respondent anonymity while maintaining sample control is presented. Keywords: computer-assisted learning, computer-assisted instruction, health care, social work, vocational education, computerized patient record, online survey

Effect of timing of a deficit-irrigation allocation on corn evapotranspiration, yield, water use efficiency and dry mass

Water regulations have decreased irrigation water supplies in Nebraska and some other areas of the USA Great Plains. When available water is not enough to meet crop water requirements during the entire growing cycle, it becomes critical to know the proper irrigation timing that would maximize yields and profits. This study evaluated the effect of timing of a deficit-irrigation allocation (150 mm) on crop evapotranspiration (ETc), yield, water use efficiency (WUE = yield/ETc), irrigation water use efficiency (IWUE = yield/irrigation), and dry mass (DM) of corn (Zea mays L.) irrigated with subsurface drip irrigation in the semiarid climate of North Platte, NE. During 2005 and 2006, a total of sixteen irrigation treatments (eight each year) were evaluated, which received different percentages of the water allocation during July, August, and September. During both years, all treatments resulted in no crop stress during the vegetative period and stress during the reproductive stages, which affected ETc, DM, yield, WUE and IWUE. Among treatments, ETc varied by 7.2 and 18.8%; yield by 17 and 33%; WUE by 12 and 22%, and IWUE by 18 and 33% in 2005 and 2006, respectively. Yield and WUE both increased linearly with ETc and with ETc/ETp (ETp = seasonal ETc with no water stress), and WUE increased linearly with yield. The yield response factor (ky) averaged 1.50 over the two seasons. Irrigation timing affected the DM of the plant, grain, and cob, but not that of the stover. It also affected the percent of DM partitioned to the grain (harvest index), which increased linearly with ETc and averaged 56.2% over the two seasons, but did not affect the percent allocated to the cob or stover. Irrigation applied in July had the highest positive coefficient of determination (R2) with yield. This high positive correlation decreased considerably for irrigation applied in August, and became negative for irrigation applied in September. The best positive correlation between the soil water deficit factor (Ks) and yield occurred during weeks 12-14 from crop emergence, during the "milk" and "dough" growth stages. Yield was poorly correlated to stress during weeks 15 and 16, and the correlation became negative after week 17. Dividing the 150 mm allocation about evenly among July, August and September was a good strategy resulting in the highest yields in 2005, but not in 2006. Applying a larger proportion of the allocation in July was a good strategy during both years, and the opposite resulted when applying a large proportion of the allocation in September. The different results obtained between years indicate that flexible irrigation scheduling techniques should be adopted, rather than relying on fixed timing strategies.

Koulukasvatusta teknologisoituvaan yhteiskuntaan : Kansakoulun opetussuunnitelman rakentuminen, 1945-1952

Education for a Technological Society. Public School Curriculum Construction, 1945-1952. The subject of my research is the significance of technology in the construction process of the public school curriculum during the years 1945-1952. During the period the war reparation and rebuilding placed demands and actions to rationalise and dramatise industry and agriculture. Thereby the ambitions of building a technological country and the reformation of curriculum took place simultaneously. Fordistian terms of reference, of which the principles were mass production, rationalisation and standardisation, a hierarchical division of labour and partition of assignments, provided a model for the developing curriculum. In the research the curriculum is examined as an artefact, which shapes socio-technically under the influence of social and technical factors. In the perspective of socio-technical construction the artefact is represented by the viewpoints of members of relevant social groups. The groups give meaning to the curriculum artefact, which determines the components of the curriculum. The weakness of the curriculum was its ineffectiveness, which was due to three critical problems. Firstly, the curriculum was to be based on scientific work, which meant the development of schools through experiments and scientific research. Secondly, the civilised conseption in the curriculum was to be composed of theoretical knowledge, as well as practical skills. Practical education was useful for both the individual and society. Thirdly, the curriculum was to be reformed in a way that the individuality of the pupil would be taken into account. It was useful for the society that talents and natural abilities of every pupil were observed and used to direct the pupil to the proper place in the social division of labour, according to the "right man in a right place" principle. The solutions to critical problems formed the instructions of the public school curriculum, which described the nature and content of education. Technology and its development were on essential part of the whole school curriculum process. The quality words connected to the development of technology - progress, rationality and effectiveness - were also suitable qualifiers and reasons for the reform of the curriculum. On the other hand, technology set a point of comparison and demand for the development of all phases of education. The view of technology was not clearly deterministic - it was also possible to shape technological society with the help of education. The public school curriculum process indicates how originally the principles of technological systems were shaped to the language of education and accepted in educational content.

Hip power analysis in individuals with transfemoral amputation: A different strategy different from stabilisation during gait stance

Introduction and Objectives Joint moments and joint powers during gait are widely used to determine the effects of rehabilitation programs as well as prosthetic fitting. Following the definition of power (dot product of joint moment and joint angular velocity) it has been previously proposed to analyse the 3D angle between both vectors, αMw. Basically, joint power is maximised when both vectors are parallel and cancelled when both vectors are orthogonal. In other words, αMw < 60° reveals a propulsion configuration (more than 50% of the moment contribute to positive power) while αMw > 120° reveals a resistance configuration (more than 50% of the moment contribute to negative power). A stabilisation configuration (less than 50% of the moment contribute to power) corresponds to 60° < αMw < 120°. Previous studies demonstrated that hip joints of able-bodied adults (AB) are mainly in a stabilisation configuration (αMw about 90°) during the stance phase of gait. [1, 2] Individuals with transfemoral amputation (TFA) need to maximise joint power at the hip while controlling the prosthetic knee during stance. Therefore, we tested the hypothesis that TFAs should adopt a strategy that is different from a continuous stabilisation. The objective of this study was to compute joint power and αMw for TFA and to compare them with AB. Methods Three trials of walking at self-selected speed were analysed for 8 TFAs (7 males and 1 female, 46±10 years old, 1.78±0.08 m 82±13 kg) and 8 ABs (males, 25±3 years old, 1.75±0.04, m 67±6 kg). The joint moments are computed from a motion analysis system (Qualisys, Goteborg, Sweden) and a multi-axial transducer (JR3, Woodland, USA) mounted above the prosthetic knee for TFAs and from a motion analysis system (Motion Analysis, Santa Rosa, USA) and force plates (Bertec, Columbus, USA) for ABs. The TFAs were fitted with an OPRA (Integrum, AB, Gothengurg, Sweden) osseointegrated implant system and their prosthetic designs include pneumatic, hydraulic and microprocessor knees. Previous studies showed that the inverse dynamics computed from the multi-axial transducer is the proper method considering the absorption at the foot and resistance at the knee. Results The peak of positive power at loading response (H1) was earlier and lower for TFA compared to AB. Although the joint power is lower, the 3D angle between joint moment and joint angular velocity, αMw, reveals an obvious propulsion configuration (mean αMw about 20°) for TFA compared to a stabilisation configuration (mean αMw about 70°) for AB. The peaks of negative power at midstance (H2) and of positive power at preswing / initial swing (H3) occurred later, lower and longer for TFA compared to AB. Again, the joint powers are lower for TFA but, in this case, αMw is almost comparable (with a time lag), demonstrating a stabilisation (almost a resistance for TFA, mean αMw about 120°) and a propulsion configuration, respectively. The swing phase is not analysed in the present study. Conclusion The analysis of hip joint power may indicate that TFAs demonstrated less propulsion and resistance than ABs during the stance phase of gait. This is true from a quantitative point of view. On the contrary, the 3D angle between joint moment and joint angular velocity, αMw, reveals that TFAs have a remarkable propulsion strategy at loading response and almost a resistance strategy at midstance while ABs adopted a stabilisation strategy. The propulsion configuration, with αMw close to 0°, seems to aim at maximising the positive joint power. The configuration close to resistance, with αMw far from 180°, might aim at unlocking the prosthetic knee before swing while minimising the negative power. This analysis of both joint power and 3D angle between the joint moment and the joint angular velocity provides complementary insights into the gait strategies of TFA that can be used to support evidence-based rehabilitation and fitting of prosthetic components.

Biophysical Characterization of Oxidized Phospholipids : Implications for Altered Membrane Structure and Function

The present study aims to elucidate the modifications in the structure and functionality of the phospholipid matrix of biological membranes brought about by free radical-mediated oxidative damage of its molecular constituents. To this end, the surface properties of two oxidatively modified phospholipids bearing an aldehyde or carboxyl function at the end of truncated sn-2 acyl chain were studied using a Langmuir balance. The results obtained reveal both oxidized species to have a significant impact on the structural dynamics of phospholipid monolayers, as illustrated by the progressive changes in force-area isotherms with increasing mole fraction of the oxidized lipid component. Moreover, surface potential measurements revealed considerable modifications in the electric properties of oxidized phospholipid containing monolayers during film compression, suggesting a packing state-controlled reorientation of the intramolecular electric dipoles of the lipid headgroups and acyl chains. Based on the above findings, a model describing the conformational state of oxidized phospholipid molecules in biological membranes is proposed, involving the protrusion of the acyl chains bearing the polar functional groups out from the hydrocarbon phase to the surrounding aqueous medium. Oxidative modifications alter profoundly the physicochemical properties of unsaturated phospholipids and are therefore readily anticipated to have important implications for their interactions with membrane-associating molecules. Along these lines, the carboxyl group bearing lipid was observed to bind avidly the peripheral membrane protein cytochrome c. The binding was reversed following increase in ionic strength or addition of polyanionic ATP, thus suggesting it to be driven by electrostatic interactions between cationic residues of the protein and the deprotonated lipid carboxyl exposed to the aqueous phase. The presence of aldehyde function bearing oxidized phospholipid was observed to enhance the intercalation of four antimicrobial peptides into phospholipid monolayers and liposomal bilayers. Partitioning of the peptides to monolayers was markedly attenuated by the aldehyde scavenger methoxyamine, revealing it to be mediated by the carbonyl moiety possibly through efficient hydrogen bonding or, alternatively, formation of covalent adduct in form of a Schiff base between the lipid aldehydes and primary amine groups of the peptide molecules. Lastly, both oxidized phospholipid species were observed to bind with high affinity three small membrane-partitioning therapeutic agents, viz. chlorpromazine, haloperidol, and doxorubicin. In conclusion, the results of studies conducted using biomimetic model systems support the notion that oxidative damage influences the molecular architecture as well as the bulk physicochemical properties of phospholipid membranes. Further, common polar functional groups carried by phospholipids subjected to oxidation were observed to act as molecular binding sites at the lipid-water interface. It is thus plausible that oxidized phospholipid species may elicit cellular level effects by modulating integration of various membrane-embedded and surface-associated proteins and peptides, whose conformational state, oligomerization, and functionality is known to be controlled by highly specific lipid-protein interactions and proper physical state of the membrane environment.

Indigenous Intellectual Property: A Handbook of Contemporary Research

Taking an interdisciplinary approach unmatched by any other book on this topic, this thoughtful Handbook considers the international struggle to provide for proper and just protection of Indigenous intellectual property (IP). In light of the United Nations Declaration on the Rights of Indigenous Peoples 2007, expert contributors assess the legal and policy controversies over Indigenous knowledge in the fields of international law, copyright law, trademark law, patent law, trade secrets law, and cultural heritage. The overarching discussion examines national developments in Indigenous IP in the United States, Canada, South Africa, the European Union, Australia, New Zealand, and Indonesia. The Handbook provides a comprehensive overview of the historical origins of conflict over Indigenous knowledge, and examines new challenges to Indigenous IP from emerging developments in information technology, biotechnology, and climate change. Practitioners and scholars in the field of IP will learn a great deal from this Handbook about the issues and challenges that surround just protection of a variety of forms of IP for Indigenous communities. Preface The Legacy of David Unaipon Matthew Rimmer Introduction: Mapping Indigenous Intellectual Property Matthew Rimmer PART I INTERNATIONAL LAW 1. The United Nations Declaration on the Rights of Indigenous Peoples: A Human Rights Framework for Indigenous Intellectual Property Mauro Barelli 2. The WTO, The TRIPS Agreement and Traditional Knowledge Tania Voon 3. The World Intellectual Property Organization and Traditional Knowledge Sara Bannerman 4. The World Indigenous Network: Rio+20, Intellectual Property, Indigenous Knowledge, and Sustainable Development Matthew Rimmer PART II COPYRIGHT LAW AND RELATED RIGHTS 5. Government Man, Government Painting? David Malangi and the 1966 One-Dollar Note Stephen Gray 6. What Wandjuk Wanted Martin Hardie 7. Avatar Dreaming: Indigenous Cultural Protocols and Making Films Using Indigenous Content Terri Janke 8. The Australian Resale Royalty for Visual Artists: Indigenous Art and Social Justice Robert Dearn and Matthew Rimmer PART III TRADE MARK LAW AND RELATED RIGHTS 9. Indigenous Cultural Expression and Registered Designs Maree Sainsbury 10. The Indian Arts and Crafts Act: The Limits of Trademark Analogies Rebecca Tushnet 11. Protection of Traditional Cultural Expressions within the New Zealand Intellectual Property Framework: A Case Study of the Ka Mate Haka Sarah Rosanowski 12 Geographical Indications and Indigenous Intellectual Property William van Caenegem PART IV PATENT LAW AND RELATED RIGHTS 13. Pressuring ‘Suspect Orthodoxy’: Traditional Knowledge and the Patent System Chidi Oguamanam, 14. The Nagoya Protocol: Unfinished Business Remains Unfinished Achmad Gusman Siswandi 15. Legislating on Biopiracy in Europe: Too Little, too Late? Angela Daly 16. Intellectual Property, Indigenous Knowledge, and Climate Change Matthew Rimmer PART V PRIVACY LAW AND IDENTITY RIGHTS 17. Confidential Information and Anthropology: Indigenous Knowledge and the Digital Economy Sarah Holcombe 18. Indigenous Cultural Heritage in Australia: The Control of Living Heritages Judith Bannister 19. Dignity, Trust and Identity: Private Spheres and Indigenous Intellectual Property Bruce Baer Arnold 20. Racial Discrimination Laws as a Means of Protecting Collective Reputation and Identity David Rolph PART VI INDIGENOUS INTELLECTUAL PROPERTY: REGIONAL PERSPECTIVES 21. Diluted Control: A Critical Analysis of the WAI262 Report on Maori Traditional Knowledge and Culture Fleur Adcock 22. Traditional Knowledge Governance Challenges in Canada Jeremy de Beer and Daniel Dylan 23. Intellectual Property protection of Traditional Knowledge and Access to Knowledge in South Africa Caroline Ncube 24. Traditional Knowledge Sovereignty: The Fundamental Role of Customary Law in Protection of Traditional Knowledge Brendan Tobin Index

On the kinetics of crystal growth from a supercooled melt

We present a theoretical analysis of the dynamics of crystal growth from a supercooled melt. A molecular theory of crystal growth that pays proper attention to the structure at the liquid-solid interface is discussed.