Design and experimental characterization of antennas and wireless systems for innovative wearable and implantable ultra low–power applications

The present PhD thesis exploits the design skills I have been improving since my master thesis’ research. A brief description of the chapters’ content follows. Chapter 1: the simulation of a complete front–end is a very complex problem and, in particular, is the basis upon which the prediction of the overall performance of the system is possible. By means of a commercial EM simulation tool and a rigorous nonlinear/EM circuit co–simulation based on the Reciprocity Theorem, the above–mentioned prediction can be achieved and exploited for wireless links characterization. This will represent the theoretical basics of the entire present thesis and will be supported by two RF applications. Chapter 2: an extensive dissertation about Magneto–Dielectric (MD) materials will be presented, together with their peculiar characteristics as substrates for antenna miniaturization purposes. A designed and tested device for RF on–body applications will be described in detail. Finally, future research will be discussed. Chapter 3: this chapter will deal with the issue regarding the exploitation of renewable energy sources for low–energy consumption devices. Hence the problem related to the so–called energy harvesting will be tackled and a first attempt to deploy THz solar energy in an innovative way will be presented and discussed. Future research will be proposed as well. Chapter 4: graphene is a very promising material for devices to be exploited in the RF and THz frequency range for a wide range of engineering applications, including those ones marked as the main research goal of the present thesis. This chapter will present the results obtained during my research period at the National Institute for Research and Development in Microtechnologies (IMT) in Bucharest, Romania. It will concern the design and manufacturing of antennas and diodes made in graphene–based technology for detection/rectification purposes.

Nano-fabrication of complex functional structures using non- conventional lithography

In Chapter 1 I will present a brief introduction on the state of art of nanotechnologies, nanofabrication techniques and unconventional lithography as a technique to fabricate the novel electronic device as resistive switch so-called memristor is shown. In Chapter 2 a detailed description of the main fabrication and characterization techniques employed in this work is reported. Chapter 3 parallel local oxidation lithography (pLOx) describes as a main technique to obtain accurate patterning process. All the effective parameters has been studied and the optimized condition observed to highly reproducible with excellent patterned nanostructures. The effect of negative bias, calls local reduction (LR) studied. Moreover, the use of AC bias shows faster patterning process respect to DC bias. In Chapter 4 (metal/ e-SiO2/ Si nanojunction) it is shown how the electrochemical oxide nanostructures by using pLOx can be used in the fabrication of novel devices call memristor. We demonstrate a new concept, based on conventional materials, where the lifetime problem is resolved by introducing a “regeneration” step, which restores the nano-memristor to its pristine condition by applying an appropriate voltage cycle. In Chapter 5 (Graphene/ e-SiO2/ Si), Graphene as a building block material is used as an electrode to selectively oxidize the silicon substrate by pLOx set up for the fabrication of novel resistive switch device. In Chapter 6 (surface architecture) I will show another application of pLOx in biotechnology is shown. So the surface functionalization combine with nano-patterning by pLOx used to design a new surface to accurately bind biomolecules with the possibility of studying those properties and more application in nano-bio device fabrication. So, in order to obtain biochips, electronic and optical/photonics devices Nano patterning of DNA used as scaffolds to fabricate small functional nano-components.

Nanographene als funktionale Materialien und synthetische Herausforderung

Im Rahmen dieser Arbeit wurden neuartige funktionale Nanographene synthetisiert und hinsichtlich ihrer strukturellen und elektronischen Eigenschaften charakterisiert. Basierend auf dem Strukturmotiv des Graphens konnten anellierte polyzyklische aromatische Kohlenwasserstoffe (PAKs) mit unterschiedlichen Seitenverhältnissen strukturdefiniert erhalten und gezielt in der Peripherie funktionalisiert werden. Basierend auf dem Synthesekonzept einer „Vorplanarisierung“ konnten Nanographen-Scheiben mit einem Durchmesser von bis zu 3 nm in hoher Reinheit erhalten werden. Durch die Entwicklung von Polyphenylen-Vorläufern mit einem gewinkelten Rückgrat konnten erstmals defektfreie und lösliche Nanographen-Streifen (GNRs) mit Breiten von 1,0 - 2,1 nm und Längen von über 40 nm synthetisiert werden.rnrnAm Hexa-peri-hexabenzocoronen (HBC) war es möglich, durch die Einführung kurzer linearer Alkylreste in der Peripherie den inter- und intrakolumnaren Abstand nach Selbstorganisation zu reduzieren. In Mischungen mit Perylentetracarboxydiimid (PDI) als Akzeptor konnte durch eine erhöhte Dichte und eine verbesserte Ladungsträgermobilität eine relative Steigerung der Effizienz von Donor-Akzeptor-Heteroübergangs-Solarzellen um 9 % erreicht werden. Eine kovalente Verknüpfung von HBC und PDI erlaubte hier die vollständige Kontrolle der supramolekularen Organisation, des Phasenverhaltens sowie des Abstandes zwischen Donor und Akzeptor.rnrnBasierend auf den im Rahmen dieser Arbeit entwickelten Synthesekonzepten, eröffnen sich nun zahlreiche Möglichkeiten zur Entwicklung weiterer Nanographene, die entsprechend der gewünschten Anwendung funktionalisiert werden können und ein besseres Verständnis der Eigenschaften graphenartiger Materialien erlauben werden.

From large polycyclic aromatic hydrocarbons to extended aromate-rich networks

The common ground of this study is the development of novel synthetic strategies to extended one-, two- and three-dimensional aromate-rich systems for which a number of applications are envisaged. rnThe point of departure is the synthesis and characterization of highly symmetric macrocyclic PAHs (polycyclic aromatic hydrocarbons) for which various aspects of supramolecular chemistry will be investigated. The versatility of the Yamamoto macrocyclization will be demonstrated on the basis of a set of cyclic trimers that exhibit a rich supramolecular chemistry. 1,10-phenanthroline, triphenylene and ortho-terphenyl building blocks have been successfully assembled to the corresponding macrocycles following the newly developed synthetic route. Scanning-tunneling microscopy (STM) and two-dimensional wide-angle X-ray scattering (2D-WAXS) were used to study the two- and three-dimensional self-assembly, respectively.rnSecondly, the development of chemical approaches to highly shape-anisotropic graphene nanoribbons (GNRs) and related nanographene molecules shall be discussed. Aryl-aryl coupling was used for the bottom-up fabrication of dendronized monomers, polymers and model compounds. Subsequently, these structures were converted into the final graphene material using oxidative (Scholl-type) cyclodehydrogenation. The GNRs thus obtained are characterized by an unprecedented length and lateral extension. The relevance of structural tailoring in the field of well-defined graphene materials is discussed in detail as only the chemical approach provides full geometry control. rnLastly, novel pathways towards the synthesis of extended three-dimensional networks that are dominated by nitrogen-rich motifs will be presented. If porous, these materials hold a great potential in the fields of gas and energy storage as well as for applications in catalysis. Hence, poly(aminal) networks based on melamine as crosslinking unit were synthesized and characterized with respect to the applications mentioned above. As set of conjugated poly(azomethine) networks was investigated regarding their use as a novel class of organic semiconductors for photocatalytic water splitting. The network structures described in this chapter can also be subjected to a controlled pyrolysis yielding mesoporous, nitrogen-rich carbon materials that were evaluated as active component for supercapacitors.rn

Spectroscopic investigations of functional bulk and thin film Heusler alloys

Functional and smart materials have gained large scientific and practical interest in current research and development. The Heusler alloys form an important class of functional materials used in spintronics, thermoelectrics, and for shape memory alloy applications. An important aspect of functional materials is the adaptability of their physical properties. In this work functional polycrystalline bulk and epitaxial thin film Heusler alloys are characterized by means of spectroscopic investigation methods, X-ray magnetic circular dichroism (XMCD) and energy dispersive X-ray analysis (EDX). With EDX the homogeneity of the samples is studied extensively. For some cases of quaternary compounds, for example Co2(MnxTi1−x)Sn and Co2(Mn0.5Dy0.5)Sn, an interesting phase separation in two nearly pure ternary Heusler phases occurs. For these samples the phase separation leads to an improvement of thermoelectric properties. XMCD as the main investigation method was used to study Co2TiZ (Z = Si, Sn, and Sb), Co2(MnxTi1−x)Si, Co2(MnxTi1−x)Ge, Co2Mn(Ga1−xGex), Co2FeAl, Mn2VAl, and Ni2MnGa Heusler compounds. The element-specific magnetic moments are calculated. Also, the spin-resolved unoccupied density of states is determined, for example giving hints for half-metallic ferromagnetism for some Co-based compounds. The systematic change of the magnetic moments and the shift of the Fermi energy is a proof that Heusler alloys are suitable for a controlled tailoring of physical properties. The comparison of the experimental results with theoretical predictions improves the understanding of complex materials needed to optimize functional Heusler alloys.

Computational insight into materials properties

The aim of the work was to explore the practical applicability of molecular dynamics at different length and time scales. From nanoparticles system over colloids and polymers to biological systems like membranes and finally living cells, a broad range of materials was considered from a theoretical standpoint. In this dissertation five chemistry-related problem are addressed by means of theoretical and computational methods. The main results can be outlined as follows. (1) A systematic study of the effect of the concentration, chain length, and charge of surfactants on fullerene aggregation is presented. The long-discussed problem of the location of C60 in micelles was addressed and fullerenes were found in the hydrophobic region of the micelles. (2) The interactions between graphene sheet of increasing size and phospholipid membrane are quantitatively investigated. (3) A model was proposed to study structure, stability, and dynamics of MoS2, a material well-known for its tribological properties. The telescopic movement of nested nanotubes and the sliding of MoS2 layers is simulated. (4) A mathematical model to gain understaning of the coupled diffusion-swelling process in poly(lactic-co-glycolic acid), PLGA, was proposed. (5) A soft matter cell model is developed to explore the interaction of living cell with artificial surfaces. The effect of the surface properties on the adhesion dynamics of cells are discussed.

HCl gas gettering of 3d transition metals for crystalline silicon solar cell concepts

In order to reduce the costs of crystalline silicon solar cells, low-cost silicon materials like upgraded metallurgical grade (UMG) silicon are investigated for the application in the photovoltaic (PV) industry. Conventional high-purity silicon is made by cost-intensive methods, based on the so-called Siemens process, which uses the reaction to form chlorosilanes and subsequent several distillation steps before the deposition of high-purity silicon on slim high-purity silicon rods. UMG silicon in contrast is gained from metallurgical silicon by a rather inexpensive physicochemical purification (e.g., acid leaching and/or segregation). However, this type of silicon usually contains much higher concentrations of impurities, especially 3d transition metals like Ti, Fe, and Cu. These metals are extremely detrimental in the electrically active part of silicon solar cells, as they form recombination centers for charge carriers in the silicon band gap. This is why simple purification techniques like gettering, which can be applied between or during solar cell process steps, will play an important role for such low-cost silicon materials. Gettering in general describes a process, whereby impurities are moved to a place or turned into a state, where they are less detrimental to the solar cell. Hydrogen chloride (HCl) gas gettering in particular is a promising simple and cheap gettering technique, which is based on the reaction of HCl gas with transition metals to form volatile metal chloride species at high temperatures.rnThe aim of this thesis was to find the optimum process parameters for HCl gas gettering of 3d transition metals in low-cost silicon to improve the cell efficiency of solar cells for two different cell concepts, the standard wafer cell concept and the epitaxial wafer equivalent (EpiWE) cell concept. Whereas the former is based on a wafer which is the electrically active part of the solar cell, the latter uses an electrically inactive low-cost silicon substrate with an active layer of epitaxially grown silicon on top. Low-cost silicon materials with different impurity grades were used for HCl gas gettering experiments with the variation of process parameters like the temperature, the gettering time, and the HCl gas concentration. Subsequently, the multicrystalline silicon neighboring wafers with and without gettering were compared by element analysis techniques like neutron activation analysis (NAA). It was demonstrated that HCl gas gettering is an effective purification technique for silicon wafers, which is able to reduce some 3d transition metal concentrations by over 90%. Solar cells were processed for both concepts which could demonstrate a significant increase of the solar cell efficiency by HCl gas gettering. The efficiency of EpiWE cells could be increased by HCl gas gettering by approximately 25% relative to cells without gettering. First process simulations were performed based on a simple model for HCl gas gettering processes, which could be used to make qualitative predictions.

Integrazione tecnologica di grafene cresciuto per deposizione chimica da fase vapore per applicazioni termiche e termoelettriche

L’obiettivo del lavoro di tesi è quello di studiare l’integrazione del grafene con i processi tecnologici propri della tecnologia del silicio, per la realizzazione di dispositivi innovativi per la misura delle proprietà termiche e termoelettriche del grafene che sono tra le meno studiate ad oggi. L’attività sperimentale svolta, ha riguardato l’intero processo di produzione, processing ed integrazione tecnologica del grafene. Da una parte è stato messo a punto un processo ottimizzato, partendo da una approfondita ricerca bibliografica, per il trasferimento delle membrane dai substrati di crescita, in rame, a quelli di destinazione, SiO2 e Si3N4, mantenendo la completa compatibilità con i processi della microelettronica del silicio in particolare per quanto riguarda l’eliminazione dei residui metallici dalla sintesi. Dall’altra è stata sviluppata una procedura di patterning micrometrico del grafene, affidabile e riproducibile, e, soprattutto, compatibile con la microelettronica del silicio. Le membrane, cresciute tramite deposizione da fase vapore (Chemical Vapor Deposition), sono state caratterizzate tramite la microscopia elettronica, a scansione e in trasmissione, la microscopia ottica, spettroscopia Raman e microscopia a forza atomica, tecniche che sono state utilizzate per caratterizzare i campioni durante l'intero processo di patterning. Il processo di etching del grafene in ossigeno, realizzato con il plasma cleaner, strumento che nasce per la pulizia di campioni per microscopia elettronica, è stato messo a punto il attraverso una estesa attività di test sia dei parametri di funzionamento dello strumento che del fotoresist da utilizzare. La procedura di patterning micrometrico vera e propria, ha comportato di affrontare diverse classi di problemi, dalla rimozione del fotoresist con soluzioni diverse (soluzione di sviluppo dedicata e/o acetone) alla rimozione dei residui presenti sulle membrane di grafene anche a valle del patterning stesso. La rimozione dei residui tramite acido cloridrico, insieme ad una procedura di annealing a 400°C in aria per la rimozione dei residui del fotoresist polimerico che erano presenti a valle dell’etching in ossigeno, ha permesso di ottenere un patterning del grafene ben definito su scala micrometrica e una ridottissima presenza di residui. Le procedure ottimizzate di trasferimento e di patterning sono il principale avanzamento rispetto allo stato dell’arte. Le metodiche messe a punto in questo lavoro, consentiranno di integrare il grafene direttamente nel processo di micro-fabbricazione di dispositivi per misure termiche e termoelettriche, per i quali quali sono in realizzazione le maschere di processo che rappresentando la naturale conclusione del lavoro di tesi.

Laserablation von oxidischen Multilagenstrukturen zur Untersuchung von heteroepitaktischen Grenzflächenzuständen

Die Deposition von dünnen, metallischen Schichten auf Silizium-Substraten stellt bereits seit Jahrzehnten die wichtigste Möglichkeit dar, um die wachsenden Anforderungen der Speichertechnologien zu erfüllen. Obwohl Multilagenstrukturen aus oxidischen Schichten eine nahezu unerschöpfliche Vielfalt an neuen Effekten bieten, kommen diese aktuell nur in Nischenanwendungen zum Einsatz. Der Fokus dieser Arbeit liegt auf dem Verständnis von Phänomenen, die nur an Grenzflächensystemen zu beobachten sind. Die Basis der Untersuchungen stellten die Präparation der Multilagenstrukturen durch Laserablation dar. Eine Untersuchung der strukturellen Eigenschaften von multiferroischen BiFeO3 (BFO)-Schichten erlaubte eine Analyse der Wachstumsmodi und der Symmetrie der Einheitszelle von BFO unter heteroepitaktischer Verspannung. Durch Piezokraftmikroskopie konnte die ferroelektrische Domänenstruktur dünner BFO-Schichten analysiert werden. Die Abbildung der magnetischen Domänenstruktur der ferromagnetischen La0,67Sr0,33MnO3 (LSMO)-Schicht und der antiferromagnetischen BFO-Schicht einer Bilagenstruktur durch Photoemissionselektronenmikroskopie erlaubte eine Analyse der Austauschkopplung an der Grenzfläche. Durch elektronische Rekonstruktion entsteht an der LaAlO3 (LAO) /SrTiO3 (STO)-Grenzfläche ein leitfähiger, quasi-zweidimensionaler Zustand. Dessen Transporteigenschaften wurden mit einem Schwerpunkt auf deren Beeinflussung durch ein elektrisches Feld charakterisiert. Diese Ergebnisse führten zur Implementierung einer ferroelektrischen BFO-Schicht zur Manipulation der Leitfähigkeit an der LAO/STO-Grenzfläche. Die Kontrolle des Widerstandes eines mikrostrukturierten Bereichs durch die Polarisation der BFO-Schicht erlaubt die Nutzung der Struktur als Speichertechnologie.

Dotierte Nanographenstreifen mit definierten Randstrukturen

Die in der vorliegenden Dissertation entwickelten organochemischen Protokolle und Konzepte erweitern die Bottom-Up-Synthese von atompräzisen Nanographenstreifen (GNR) um zwei fundamentale Bereiche. Zum einen die Dotierung der halbleitenden GNR mit Schwefel oder Stickstoffatomen und zum anderen ein Protokoll für eine lösungsbasierte Synthese von stickstoffdotierten Zickzack-Streifen.rnDie Dotierung von GNR beinhaltet die Synthese von monomeren Bausteinen bei denen, im Gegensatz zu ihren reinen Kohlenstoffhomologen, definierte Positionen am Rand mit zwei oder vier Stickstoff- beziehungsweise zwei Schwefelatomen ersetzt wurden. Die Synthese atompräziser GNR konnte mit verschiedenen experimentellen Methoden analysiert und anschaulich über STM visualisiert werden. Neben einer n-Dotierung gelang so auch erstmals eine Bottom-Up-Synthese von schwefeldotierten GNR. Eine mögliche Anwendung in der Nanoelektronik aufbauend auf dotierten GNR wurde bestätigt, indem durch Co-Polymerisation von stickstoffhaltigen mit reinen Kohlenstoffmonomeren Heteroschnittstellen zwischen dotierten und undotierten Bereichen hergestellt werden konnten. Solche Heteroschnittstellen sind fundamentale Grundlage von Dioden und damit Basis einer Vielzahl elektronischer Elemente wie Solarzellen oder Leuchtdioden.rnWährend für halbleitende GNR mit einer Armlehnen-Form ein breites Spektrum an organischen Syntheseprotokollen zur Verfügung stand, existierte zu Beginn dieser Arbeit keines für GNR mit Zickzack-Struktur. Innerhalb dieser Arbeit konnte eine Bottom-Up-Synthese zur Erschließung stickstoffdotierter GNR mit Zickzack-Randstruktur erarbeitet werden. Durch die Verwendung eines (2-Hydroxymethyl)phenylboronsäureesters werden Hydroxymethylsubsituenten entlang eines Polyphenylenrückgrats eingebaut, die nach Kondensation mit dem Stickstoffatom eine Zickzack-Kante ergeben. Innerhalb der synthetisierten Zielstrukturen kann das 9a-Azaphenalen als letztes, bislang nicht erschlossenes Isomer der Azaphenalene, als wiederkehrende Struktur, gefunden werden. Die Reaktivität der Zickzackkante konnte zudem zum Aufbau einer Vielzahl bislang unzugänglicher, polycyclischer Heteroaromaten über 1,3-dipolare Addition dieses polycyclischen Azomethin Ylides (PAMY) genutzt werden.rn

Non-aqueous dispersions of particles and their applications

In the current work, three studies about non-aqueous dispersions of particles were carried out by using an amphiphilic block copolymer poly(isoprene)-block-poly(methyl methacrylate) (PI-b-PMMA) as stabilizer:rn1. Dispersions of polyurethane and polyurea porous particles for polymer compositesrn2. Dispersions of PMMA and PU particles with PDI dye for study of Single Molecule Spectroscopy Detectionrn3. Dispersions of graphene nanosheets for polymer compositesrnrnIn the first study, highly porous polyurethane and polyurea particles were prepared in a non-aqueous emulsion. The preparation of porous particles consisted of two parts: At first, a system was developed where the emulsion had high stability for the polymerization among diisocyanate, diol and water. In the second part, porous particles were prepared by using two methods fission/fusion and combination by which highly porous particles were obtained. In this study, the applications of porous particles were also investigated where polyurethane particles were tested as filling material for polymer composites and as catalyst carrier for polyethylene polymerization. rnrnIn the second study, PMMA and PU particles from one non-aqueous emulsion were investigated via single molecule fluorescence detection. At first the particles were loaded with PDI dye, which were detected by fluorescence microscopy. The distribution and orientation of the PDI molecules in the particles were successfully observed by Single Molecule Fluorescence Detection. The molecules were homogenously distributed inside of the particles. In addition they had random orientation, meaning that no aggregations of dye molecules were formed. With the results, it could be supposed that the polymer chains were also homogenously distributed in the particles, and that the conformation was relatively flexible. rnrnIn the third part of the study, graphene nanosheets with high surface area were dispersed in an organic solvent with low boiling point and low toxicity, THF, stabilized with a block copolymer PI-b-PMMA. The dispersion was used to prepare polymer composites. It was shown that the modified graphene nanosheets had good compatibility with the PS and PMMA matrices. rn

Studio nanomorfologico di superficie tramite microscopia a forza atomica di grafite minerale e grafene

L’obiettivo di questa tesi è esfoliare mediante tecnica LPE qualche layer di grafite ed analizzare il campione ottenuto mediante la tecnica AFM. Negli studi sperimentali svolti nell’ambito di questa tesi sono state condotte tre tipologie di esperimenti: 1) analisi della grafite minerale prima del trattamento di esfoliazione; 2) esfoliazione LPE di grafite fissata su substrato di muscovite, in bagno ultrasonico con acqua bidistillata; 3) esfoliazione LPE di grafite fissata su muscovite, in bagno ultrasonico con azoto liquido. L’ultrasonicazione ha portato al distacco ed isolamento di frammenti di grafite di forma tipicamente triangolare e di dimensioni laterali micrometriche, i quali si sono depositati sul substrato di muscovite e ridepositati sulla grafite stessa. Inoltre ho osservato la presenza di diversi DLG (double-layer graphene) e addirittura la presenza di SLG (single-layer graphene) estesi alcune centinaia di nm. L’analisi AFM ha mostrato la presenza di bordi cristallografici definiti, a volte con la presenza di angoli di 120° e ha mostrato il fenomeno del “folding”.

Grafene: Proprieta, sintesi e applicazioni

Nel 2004 due Fisici dell’Università di Manchester, nel Regno Unito, isolarono per la prima volta un materiale dallo spessore di un singolo atomo: il grafene. Questo materiale, composto da un reticolo di atomi di carbonio disposti a nido d’ape, possiede interessanti proprietà chimiche e fisiche, tra le quali una elevata resistenza chimica e meccanica, un eccellente trasporto termico ed elettrico ed un’ elevata trasparenza. Il crescente fermento attorno al grafene ha suscitato un forte interesse a livello europeo, al punto che la Comunità Europea ha approvato due dei più grandi progetti di ricerca mai finanziati in Europa, tra questi il Graphene Flagship Project (www.graphene-flagship.eu) che coinvolge oltre 120 gruppi di ricerca da 17 Stati Europei e distribuirà nei prossimi anni 1,000 milioni di euro per lo sviluppo di tecnologie e dispositivi a base grafene. Con Flagship Grafene l’Europa punta sul grafene, e lo fa in grande. L’obiettivo è dunque ambizioso. Il suddetto materiale è infatti non solo il più sottile che conosciamo, con uno spessore di un atomo di carbonio, ma è anche 100 volte più resistente dell’acciaio e al tempo stesso flessibile. E’ Inoltre trasparente e conduce l’energia elettrica e termica molto meglio del rame. Ergo, il grafene offre le stesse performance dei materiali usati attualmente nei nostri dispositivi, con l’aggiunta però di ulteriori funzionalità.

Electrospun chitosan nanofibers for virus removal

Electrospinning uses electrostatic forces to create nanofibers that are far smaller than conventional fiber spinning process. Nanofibers made with chitosan were created and techniques to control fibers diameter and were well developed. However, the adsorption of porcine parvovirus (PPV) was low. PPV is a small, nonenveloped virus that is difficult to remove due to its size, 18-26 nm in diameter, and its chemical stability. To improve virus adsorption, we functionalized the nanofibers with a quaternized amine, forming N-[(2-hydroxy-3-trimethylammonium) propyl] chitosan chloride (HTCC). This was blended with additives to increase the ability to form HTCC nanofibers. The additives changed the viscosity and conductivity of the electrospinning solution. We have successfully synthesized and functionalized HTCC nanofibers that absorb PPV. HTCC blend with graphene have the ability to remove a minimum of 99% of PPV present in solution.

Investigation into the enhancement of polycarbonate with conductive nanomaterials

Polymers are typically electrically and thermally insulating materials. The electrical and thermal conductivities of polymers can be increased by the addition conductive fillers such as carbons. Once the polymer composites have been made electrically and thermally conductive, they can be used in applications where these conductivities are desired such as electromagnetic shielding and static dissipation. In this project, three carbon nanomaterials are added to polycarbonate to enhance the electrical and thermal conductivity of the resulting composite. Hyperion Catalysis FIBRILs carbon nanotubes were added to a maximum loading of 8 wt%. Ketjenblack EC-600 JD carbon black was added to a maximum loading of 10 wt%. XG Sciences xGnP™ graphene nanoplatelets were added to a maximum loading of 15 wt%. These three materials have drastically different morphologies and will have varying effects on the various properties of polycarbonate composites. It was determined that carbon nanotubes have the largest effect on electrical conductivity with an 8 wt% carbon nanotube in polycarbonate composite having an electrical conductivity of 0.128 S/cm (from a pure polycarbonate value of 10-17 S/cm). Carbon black has the next largest effect with an 8 wt% carbon black in polycarbonate composite having an electrical conductivity of 0.008 S/cm. Graphene nanoplatelets have the least effect with an 8 wt% graphene nanoplatelet in polycarbonate having an electrical conductivity of 2.53 x 10-8 S/cm. Graphene nanoplatelets show a significantly higher effect on increasing thermal conductivity than either carbon nanotubes or carbon black. Mechanically, all three materials have similar effects with graphene nanoplatelets being somewhat more effective at increasing the tensile modulus of the composite than the other fillers. Carbon black and graphene nanoplatelets show standard carbon-filler rheology where the addition of filler increases the viscosity of the resulting composite. Carbon nanotubes, on the other hand, show an unexpected rheology. As carbon nanotubes are added to polycarbonate the viscosity of the composite is reduced below that of the original polycarbonate. It was seen that the addition of carbon nanotubes offsets the increased viscosity from a second filler, such as carbon black or graphene nanoplatelets.