Fouling management and retention in nanofiltration of integrated paper mill effluents

Nanofiltration performance was studied with effluents from the pulp and paper industry and with model substances. The effect of filtration conditions and membrane properties on nanofiltration flux, retention, and fouling was investigated. Generally, the aim was to determine the parameters that influence nanofiltration efficiency and study how to carry out nanofiltration without fouling by controlling these parameters. The retentions of the nanofiltration membranes studied were considerably higher than those of tight ultrafiltration membranes, and the permeate fluxes obtained were approximately the same as those of tight ultrafiltration membranes. Generally, about 80% retentions of total carbon and conductivity were obtained during the nanofiltration experiments. Depending on the membrane and the filtration conditions, the retentions of monovalent ions (chloride) were between 80 and 95% in the nanofiltrations. An increase in pH improved retentions considerably and also the flux to some degree. An increase in pressure improved retention, whereas an increase in temperature decreased retention if the membrane retained the solute by the solution diffusion mechanism. In this study, more open membranes fouled more than tighter membranes due to higher concentration polarization and plugging of the membrane material. More irreversible fouling was measured for hydrophobic membranes. Electrostatic repulsion between the membrane and the components in the solution reduced fouling but did not completely prevent it with the hydrophobic membranes. Nanofiltration could be carried out without fouling, at least with the laboratory scale apparatus used here when the flux was below the critical flux. Model substances had a strong form of the critical flux, but the effluents had only a weak form of the critical flux. With the effluents, some fouling always occurred immediately when the filtration was started. However, if the flux was below the critical flux, further fouling was not observed. The flow velocity and pH were probably the most important parameters, along with the membrane properties, that influenced the critical flux. Precleaning of the membranes had only a small effect on the critical flux and retentions, but it improved the permeability of the membranes significantly.

Methods for assessing the sustainability of integrated municipal waste management and

The general striving to bring down the number of municipal landfills and to increase the reuse and recycling of waste-derived materials across the EU supports the debates concerning the feasibility and rationality of waste management systems. Substantial decrease in the volume and mass of landfill-disposed waste flows can be achieved by directing suitable waste fractions to energy recovery. Global fossil energy supplies are becoming more and more valuable and expensive energy sources for the mankind, and efforts to save fossil fuels have been made. Waste-derived fuels offer one potential partial solution to two different problems. First, waste that cannot be feasibly re-used or recycled is utilized in the energy conversion process according to EU’s Waste Hierarchy. Second, fossil fuels can be saved for other purposes than energy, mainly as transport fuels. This thesis presents the principles of assessing the most sustainable system solution for an integrated municipal waste management and energy system. The assessment process includes: · formation of a SISMan (Simple Integrated System Management) model of an integrated system including mass, energy and financial flows, and · formation of a MEFLO (Mass, Energy, Financial, Legislational, Other decisionsupport data) decision matrix according to the selected decision criteria, including essential and optional decision criteria. The methods are described and theoretical examples of the utilization of the methods are presented in the thesis. The assessment process involves the selection of different system alternatives (process alternatives for treatment of different waste fractions) and comparison between the alternatives. The first of the two novelty values of the utilization of the presented methods is the perspective selected for the formation of the SISMan model. Normally waste management and energy systems are operated separately according to the targets and principles set for each system. In the thesis the waste management and energy supply systems are considered as one larger integrated system with one primary target of serving the customers, i.e. citizens, as efficiently as possible in the spirit of sustainable development, including the following requirements: · reasonable overall costs, including waste management costs and energy costs; · minimum environmental burdens caused by the integrated waste management and energy system, taking into account the requirement above; and · social acceptance of the selected waste treatment and energy production methods. The integrated waste management and energy system is described by forming a SISMan model including three different flows of the system: energy, mass and financial flows. By defining the three types of flows for an integrated system, the selected factor results needed in the decision-making process of the selection of waste management treatment processes for different waste fractions can be calculated. The model and its results form a transparent description of the integrated system under discussion. The MEFLO decision matrix has been formed from the results of the SISMan model, combined with additional data, including e.g. environmental restrictions and regional aspects. System alternatives which do not meet the requirements set by legislation can be deleted from the comparisons before any closer numerical considerations. The second novelty value of this thesis is the three-level ranking method for combining the factor results of the MEFLO decision matrix. As a result of the MEFLO decision matrix, a transparent ranking of different system alternatives, including selection of treatment processes for different waste fractions, is achieved. SISMan and MEFLO are methods meant to be utilized in municipal decision-making processes concerning waste management and energy supply as simple, transparent and easyto- understand tools. The methods can be utilized in the assessment of existing systems, and particularly in the planning processes of future regional integrated systems. The principles of SISMan and MEFLO can be utilized also in other environments, where synergies of integrating two (or more) systems can be obtained. The SISMan flow model and the MEFLO decision matrix can be formed with or without any applicable commercial or free-of-charge tool/software. SISMan and MEFLO are not bound to any libraries or data-bases including process information, such as different emission data libraries utilized in life cycle assessments.

Implementation and Integration of New Baggage Logistic Centre at HelsinkiVantaa Airport

This thesis deals with improving international airport baggage supply chain management (SCM) by means of information technology and new baggage handling system. This study aims to focus on supply chain visibility in practice and to suggest different ways to improve the supply chain performance through information sharing. The objective is also to define how radio frequency identification (RFID) and enterprise resource planning (ERP) can make processes more transparent. In order to get full benefits from processes, effective business process management and monitoring as well as the key performance indicators must be defined, implemented and visualized through e.g. dashboard views for different roles. As an outcome of the research the need for the use of information technology systems and more advanced technologies, e.g. RFID in the supply chain management is evident. Sophisticated ERP is crucial in boosting SCM business processes and profitability. This would be beneficial for dynamic decision making as well in the airport and airline supply chain management. In the long term, economic aspects support the actions I have suggested in order to make production more flexible in reacting to quick changes.

Emergency Management and Wildland-Urban Interface Fires in the United States of America

FEMA's mission is to support our citizens and first responders to ensure that as a Nation we work together to build, sustain, and improve our capability to prepare for, protect against, respond to, recover from, and mitigate all hazards.

Sales and Operations Planning Implementation

The master’s thesis focused on implementing a sales and operations planning process. The main objectives were to create planning methods and tools for the implementation. The ultimate goal of the process, beyond this master’s thesis, is to balance the supply of products with customer demand, with optimized profitability. The theoretical part focused on giving a thorough view on the sales and operations planning process. The basis for a monthly planning cycle was identified. Methods, tools, and metrics for demand forecasting and operations planning were also introduced. Based on the theoretical part, a method for forecasting, a forecast spreadsheet, and a forecast accuracy metric were designed. A spreadsheet tool and methods were also designed for the monthly planning of production volumes, capacity, and inventory. The implementation progress was reviewed for two product families for three months. The sales and operations planning process was able to successfully identify a demand peak for the product families. Suggestions for the future of sales and operations planning were also made.

Business on demand and its mobile solution - study with SAP ByDesign

Business On-Demand solutions are widely used by SMEs in the world today. When I started working in SAP, SAP had just launched its first version mobile solutions for Business On-Demand solutions. SAP ByDesign mobile solution is great, but I believe we could do something even better on mobile phones. My job is focusing on mobile application development. Therefore, I have lots of thoughts about how we could make the mobile solutions better serve desktop solutions and how to distinguish the mobile solutions. Finally I decide to have a further research into this area. The purpose of this thesis is trying to find out how to improve the mobile solutions for Business On-Demand, find out its benefit and limits, and distinguish SaaS mobile solutions from desktop ones. In order to conduct this research, I had some online literature search to find out the Business On-Demand market and major players in this area. I compare the materials from public internet with the ones that are used internally in SAP. I had some interviews with SAP solution manager and SAP‟s potential customers. I finally made some pro-posals for mobile SaaS solutions which I believe will make the solutions better present and much helpful to the customers.

Performance of active portfolio management and the effect of stock market trend

Purpose of the study is to evaluate performance of active portfolio management and the effect of stock market trend on the performance. Theory of efficient markets states that market prices reflect all available information and that all investors share a common view of future price developments. This view gives little room for the success of active management, but the theory has been disputed – at least the level of efficiency. Behavioral finance has developed theories that identify irrational behavior patterns of investors. For example, investment decisions are not made independent of past market developments. These findings give reason to believe that also the performance of active portfolio management may depend on market developments. Performance of 16 Finnish equity funds is evaluated during the period of 2005 to 2011. In addition two sub periods are constructed, a bull market period and a bear market period. The sub periods are created by joining together the two bull market phases and the two bear market phases of the whole period. This allows for the comparison of the two different market states. Performance of the funds is measured with risk-adjusted performance by Modigliani and Modigliani (1997), abnormal return over the CAPM by Jensen (1968), and market timing by Henriksson and Merton (1981). The results suggested that in average the funds are not able to outperform the market portfolio. However, the underperformance was found to be lower than the management fees in average which suggests that portfolio managers are able to do successful investment decisions to some extent. The study revealed substantial dependence on the market trend for all of the measures. The risk-adjusted performance measure suggested that in bear markets active portfolio managers in average are able to beat the market portfolio but not in bull markets. Jensen´s alpha and the market timing model also showed striking differences between the two market states. The results of these two measures were, however, somewhat problematic and reliable conclusions about the performance could not be drawn.

Improving the inventory management and valuation process, Case: The Switch Drive Systems

The goal of this study is to create a new inventory valuation process for The Switch Drive Systems and to improve its inventory management practices. In the matter of inventories the main problems in the case company are that it doesn’t have consistent valuation methods throughout the company and that information received in ERP system isn’t trustful. The research is qualitative case study. The empirical data is gathered through observing and unstructured interviews. The research shows that material flow process and the inventory valuation must be divided and handled separately but they should interact with each other. The result is a new inventory valuation process which takes many factors of material process under the consideration in order to receive reliable value for inventories.

Transition management and the sustainable nutrients economy in the Netherlands; positioning paper

In this positioning paper transition management (TM) and the sustainable nutrient economy are addressed. We discuss TM from its scholarly origins in the 1990’s to its implementation as a comprehensive sector-wide policy program on sustainability in The Netherlands during the first decade of the 2000´s. Although the program was innovative and provoked a new approach to environmental policy and governance, the program at large failed to set the right conditions under which sustainable transition take place. Lessons from the Netherlands, both successful and less successful, are addressed in this positioning paper to inform Finnish governmental and knowledge institutes on how (not) to implement TM on environmental issues. When looking at sustainable nutrient economy the paper takes a historical view at how problems with nutrients (especially phosphates) were dealt with in the Netherlands during the post World War II era. This transition did not occur easily. In the agricultural sector environmental policies to prevent nutrient problems were not easily accepted, as large agricultural economic interests were at stake and the sector’s main actors were generally opposed to (radical) environmental transition. Currently, sustainable nutrient economy initiatives are starting to receive attention on the political agenda once again. In 2011 a sector- and chain-wide covenant was signed, showing that sustainable nutrient transition goals get commitment from stakeholders throughout the nutrient chain. We judge that TM provides useful elements that are applicable to Finnish governance modes to support sustainable nutrient economy transition. However, the Finnish government should be careful when implementing TM to prevent making the same mistakes the Dutch government made in previous years.

Lean daily management, visual management and continuous improvement

This thesis was part of lean adaptation project started at Outotec Lappeenranta factory in early 2013. The purpose of this thesis was to develop and propose lean tools that could be used in daily management, visual management and continuous improvement. This thesis was “outsiders” view, and as such, did not study the current processes deeply. As result of this thesis, two different Daily Management -boards were designed, one for parallel processes and one for sequential processes. In addition, methods of doing continuous improvement and daily task accountability were framed and standard work for the leaders outlined. The tools presented in this thesis are general tools which support work in lean environment. They are visual and, if used correctly, they provide a basis from which continuous improvement can be done. Lean philosophy emphasizes the deep understanding of the current situation and it would be against the lean principles to blindly implement anything developed “on the outside”. The tools presented should be reviewed and modified further by the people working on the factory floor.

Long-term nutrient load management and lake restoration: Case of Säkylän Pyhäjärvi (SW Finland)

Eutrophication caused by anthropogenic nutrient pollution has become one of the most severe threats to water bodies. Nutrients enter water bodies from atmospheric precipitation, industrial and domestic wastewaters and surface runoff from agricultural and forest areas. As point pollution has been significantly reduced in developed countries in recent decades, agricultural non-point sources have been increasingly identified as the largest source of nutrient loading in water bodies. In this study, Lake Säkylän Pyhäjärvi and its catchment are studied as an example of a long-term, voluntary-based, co-operative model of lake and catchment management. Lake Pyhäjärvi is located in the centre of an intensive agricultural area in southwestern Finland. More than 20 professional fishermen operate in the lake area, and the lake is used as a drinking water source and for various recreational activities. Lake Pyhäjärvi is a good example of a large and shallow lake that suffers from eutrophication and is subject to measures to improve this undesired state under changing conditions. Climate change is one of the most important challenges faced by Lake Pyhäjärvi and other water bodies. The results show that climatic variation affects the amounts of runoff and nutrient loading and their timing during the year. The findings from the study area concerning warm winters and their influences on nutrient loading are in accordance with the IPCC scenarios of future climate change. In addition to nutrient reduction measures, the restoration of food chains (biomanipulation) is a key method in water quality management. The food-web structure in Lake Pyhäjärvi has, however, become disturbed due to mild winters, short ice cover and low fish catch. Ice cover that enables winter seining is extremely important to the water quality and ecosystem of Lake Pyhäjärvi, as the vendace stock is one of the key factors affecting the food web and the state of the lake. New methods for the reduction of nutrient loading and the treatment of runoff waters from agriculture, such as sand filters, were tested in field conditions. The results confirm that the filter technique is an applicable method for nutrient reduction, but further development is needed. The ability of sand filters to absorb nutrients can be improved with nutrient binding compounds, such as lime. Long-term hydrological, chemical and biological research and monitoring data on Lake Pyhäjärvi and its catchment provide a basis for water protection measures and improve our understanding of the complicated physical, chemical and biological interactions between the terrestrial and aquatic realms. In addition to measurements carried out in field conditions, Lake Pyhäjärvi and its catchment were studied using various modelling methods. In the calibration and validation of models, long-term and wide-ranging time series data proved to be valuable. Collaboration between researchers, modellers and local water managers further improves the reliability and usefulness of models. Lake Pyhäjärvi and its catchment can also be regarded as a good research laboratory from the point of view of the Baltic Sea. The main problem in both of them is eutrophication caused by excess nutrients, and nutrient loading has to be reduced – especially from agriculture. Mitigation measures are also similar in both cases.

Soil seed bank of plant species as a function of long-term soil management and sampled depth

This study aimed at assessing the level of weed infestation indifferent areas that were submitted to different soil management for 16 years. Four management systems were studied: (1) agriculture only under conventional tillage system; (2) agriculture only under no-till system; (3) crop-livestock integrationcrop-livestock integration; (4) livestock only. These areas were sampled at three soil depths (0-5, 5-10 and 10-15 cm), and soil was stored in plastic pots and taken to a greenhouse, where soil moisture and weight were standardized. Soil was kept near 70% moisture field capacity, being revolved every 20 days when all seedling emerged from soil were counted, identified and collected for dry mass assessment. The soil coverage by weeds, number of weed seedlings and dry mass of the weedy community were assessed. A phytoecological analysis was conducted. Weed composition is differentdifferent among management systems after 16 years. Areas with livestock showed much smaller number of weed species in comparison to systems where only grain crops are grown. The presence of livestock affects the potential of germination of soil seed bank. Agriculture systems are similar in terms of weed composition along soil profile, while systems involving livestock show little relation in what regards such sampled depths. Conservationist models of land exploration contribute to reduce severity of weed species occurrence in the long term.

Finnish SMEs and Russian Business Environment: Challenges and Support Activities

The purpose of this study is based on the need of finding what kind of problems Finnish SMEs face in Russian market and how they could be supported. Used support activities in certain levels of internationalization and internationalization patterns are evaluated, international experience of entrepreneur is compared to used support activities and the most challenging pillars in Russia from the Institutional Theory are defined. The empirical part of the study is a semi structured qualitative analysis of ten case companies that represent different industry fields. All of them are SMEs and they represent different levels of internationalization and internationalization patterns. The results of this study indicated that usefulness of support activities have to be evaluated case by case. All the companies are individual organizations and usefulness of support activities have to be evaluated according to the actual situation of the company. International experience of manager has effect on the use of support activities. SMEs identified many problems related to pillars of Institutional theory and regulative environment seems to be the most challenging one.